| Age | Commit message (Collapse) | Author |
|---|
|
1. device ref pcie_rp11 -> pcie_rp9 on.
BUG=b:270657362
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: If23785f42466ba94f33d4d15dde96de29dbb3a1e
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73530
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable ELAN eKTH5015M touchscreen.
BUG=b:271966059
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I41eac949f21a48098b445f8d1b05f308672f7ab8
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Decrease Touch i2c delay during power-on sequence from 300 ms to
150 ms to make S0ix resume time meet requirement.
BUG=b:264199989
TEST=Run the following test from chroot.
test_that -b {BOARD_NAME} {device IP} f:.*power_UiResume/control
Check seconds_system_resume value less than 500 msec
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Ib81a9c1a90589b8b08e6ce6471db2abef96047ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73532
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove GPP_D11,GPP_D12 in ramstage, follow baseboard brask setting.
TEST=emerge-brask coreboot
make sure HDMIA can display
Change-Id: I953170f006699e3dc9d6111ded8234f66b9162c7
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
EC_HOST_EVENT_GPU was renamed from
EC_HOST_EVENT_USB_CHARGER and thought to no longer
be used. It was subsequently removed in
I9e3e0e9b45385766343489ae2d8fc43fb0954923
Add back the mask for this event as it is infact
required on certain Brya (Agah) and Hades variants.
Signed-off-by: Tarun Tuli <taruntuli@google.com>
BUG=b:216485035,b:258126464,b:266631157
BRANCH=none
TEST=D-notifier events are received again from EC
Change-Id: I9d7bf52efa9572e1bbd2f307420e09a7398a1ca9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73217
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Extend sd_hold to meet touchpad/touchscreen SPEC.
touchscreen:
tHD > 100 ns
touchpad:
900 ns > tHD > 300 ns
After applied the change, the tHD meets reqirement.
touchscreen:
35 ns --> 260 ns
touchpad:
43 ns --> 368 ns
BUG=b:271524470
TEST=build and measure the timing meet SPEC
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: Iec2f72da80ffe8d4dd494caabbe1a97e52a81e78
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Add SODIMM support, drop the solderdown based on schematics.
BUG=b:271199379
TEST=abuild -a -x -c max -p none -t google/brya -b hades
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I85ec79c3d8f1147a875c4d04017bb50347121ebb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Fast VMode makes the SoC throttle when the current exceeds the I_TRIP
threshold.
BUG=b:270242461
BRANCH=firmware-brya-14505.B
TEST=Verify that the feature is enabled by reading from fsp log
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I82c2016d9dfb39ff7b372815737d4ae62875340c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73373
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add minimum device tree. Leave IOs default disable to optimize variant
override complexity.
BUG=b:271199379
TEST=abuild -a -x -c max -p none -t google/brya -b hades
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ibb056c07193b4265352a9ec74829dcf02a9340bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
BUG=b:230398487
BRANCH=none
TEST=Verify USB-A device could wake up Moli.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I1c8daf62dabe674a39b1416d886f9e470ae23a5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73174
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The skolas baseboard is no longer needed, so this change removes the
baseboard files for skolas and adjusts the config settings to that
variants that used to select BOARD_GOOGLE_BASEBOARD_SKOLAS now
select BOARD_GOOGLE_BASEBOARD_BRYA and SOC_INTEL_RAPTORLAKE.
BUG=b:271470530
TEST="emerge-brya coreboot chromeos-bootimage", flash image-skolas.bin
onto a skolas and verify it boots to kernel.
Change-Id: I34cae7e471851aa52a64ce3af7bb506dc67f806b
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Fast VMode makes the SoC throttle when the current exceeds the I_TRIP
threshold.
TEST=FW_NAME=constitution emerge-brask coreboot
Change-Id: I1e68f708b7740567e24f8a3ddb9832aeec7ee6b5
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73247
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Pablo Ceballos <pceballos@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Fast VMode nmakes the SoC throttle when the current exceeds the I_TRIP
threshold.
BUG=b:270640775
BRANCH=firmware-brya-14505.B
TEST=Verify that the feature is enabled by reading from fsp log
Change-Id: I35f577e1bab0f8dda10061903df13730e2c8ee04
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Bob Moragues <moragues@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Remove world-facing microphone for xivu360.
Switching to world-facing camera will use the
user-facing microphone to record sound.
BUG=b:263927799
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: Ibb720974b6488ce4453081e0bc5b4e7f34a6b0f6
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
Update override devicetree based on schematics.
BUG=None
TEST=FW_NAME=constitution emerge-brask coreboot
Change-Id: I883a806950821e6306242975764930035a94888e
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73110
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pablo Ceballos <pceballos@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
This reverts commit 3eb17b91daac0b3acaffb01568d724d23c6f0eea.
Reason for revert:
PLTRST only keeps 18xms and it's too short for eMMC disk fully reset.
Change-Id: If4277cb600bfe4e071959dacaf204fe7d3518f68
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73202
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This reverts commit 0e0f9e51c4c4f190cbe7ef5bffa138601c644d3c.
Reason for revert:
PLTRST only keeps 18xms and it's too short for eMMC disk fully reset.
Change-Id: I13b93747bdb4d39de1ffcfdc020648871fa6e048
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73203
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Update GPP_E12,GPP_E13,GPP_H19 in ramstage.
Update GPP_F11 in bootblock.
TEST=emerge-brask coreboot
Change-Id: Icdca7f574282da140ec64cea9cdda3ebccbe3eb8
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73194
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Pablo Ceballos <pceballos@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Introduce at new config option CONFIG_FSP_PUBLISH_MBP_HOB to control
the creation of ME_BIOS_PAYLOAD_HOB (MBP HOB) by FSP.
This new option is hooked with `SkipMbpHob` UPD and is always disabled
for RPL & ADL-N based ChromeOS platforms.
It is not disabled for ADL-P based platforms because ADL-P FSP relies
on MBP HOB for ChipsetInit version for ChipsetInit sync. As ChipsetInit
sync doesn't occur if no MBP HOB, so it results S0ix issue. This
limitation is addressed in the later platforms so creation of MBP HOB
can be skipped for ADL-N and RPL based platforms.
This made skip_mbp_hob SOC chip config variable redundant which is also
removed as part of this change.
BUG=none
TEST=Build and boot to Google/Taniks.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ia396b633a71aedf592c45b69063ee0528840fd2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch makes EC wake up AP from s3/s0ix for OS shutdown/hibernate
when the state of charge drops to low_battery_shutdown_percent.
BUG=b:255465618
TEST=emerge-nissa chromeos-bootimage (EC: https://crrev.com/c/4243898)
Verify system resumes from s0ix and then enter S5 on nivviks with steps:
1. disconnect AC
2. powerd_dbus_suspend --disable_dark_resume=false
3. fakebatt 5
4. fakebatt 4
Change-Id: I63b5246432687e38ddfc5733ac3a115c3456d7e9
Signed-off-by: Ivan Chen <yulunchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73082
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Package C state demotion is now disabled for all RPL SoCs from within
soc/intel/alderlake/fsp_params, so no need to duplicate that in the
skolas devicetree.cb.
BUG=268296760
BRANCH=firmware-brya-14505.B
TEST=Boot and verified that S0ix issue is resolved.
Change-Id: I1c630e2efbdddd18a5423c79b73269e9b1be79c7
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
BUG=b:265611305
TEST=Reboot test 2500 times pass
Signed-off-by: Chia-Ling Hou <chia-ling.hou@intel.com>
Change-Id: I2b114cac58a7fadeaee6d48996cb8b51f192e78f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Add a new baseboard for hades, an Intel RPL based reference design.
Also, add variants for the reference boards hades. This commit is
a stub which only adds the minimum code needed for a successful build.
Need update gpio and memory DQ pins after final shchematic comes out.
BUG=b:269371363
TEST=abuild -a -x -c max -p none -t google/brya -b hades
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ib7fbdf997df8225cc7814a34f8b4e4e04884dbf9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Initial Aurash configuration base on moli design.
1. Set up gpio.
2. Add memory config.
3. There is no SD card setting on aurash, remove it from overridetree.
4. Follow moli psys schematic design.
5. Enable BT offload.
BUG=b:269063331
TEST=emerge-brask coreboot.
Signed-off-by: Zoey Wu <zoey_wu@wistron.corp-partner.google.com>
Change-Id: Ia9088cc2937bab72c8c22af592392384a10616a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
|
|
Add new memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
1) Samsung K3KL8L80CM-MGCT
2) Hynix H58G56BK7BX068
3) Micron MT62F1G32D2DS-026 WT:B
4) Micron MT62F512M32D2DR-031 WT:B
5) Hynix H58G56BK8BX068
BUG=b:264340545
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I1f650c7e90804e871572f42ac925da85afd7f9d3
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72886
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyle Lin <kylelinck@google.com>
|
|
Configure GPIOs according to schematics
TEST=emerge-brask coreboot
Change-Id: Ib27f1c334cad47b3be57f57b7cc8ca5530118328
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72945
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust timing parameters on i2c1 and i2c2 to meet timing requirements.
For SCL, the t-high time is now over the min 600ns requirement
for 400KHz operation (measure at over 700ns). Also, this change
does not violate other parameters - rise time, setup time and hold time.
BUG=b:264704732
TEST=Verified all timings meet spec now
Change-Id: I0e92b2c9c25e7fb5fa7082af3f4a88da168c3ef2
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This reverts commit e30695dbe196ea42864ad03af799706eaae11f02.
for meet thermal criteria, modify PS1/PS2 cutoff to default value
BUG=b:229803757
BRANCH=brya
TEST='FW_NAME=vell emerge-brya coreboot'
Change-Id: Ie009788116f1e25db8aed2df58102a316a8aeef2
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72833
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
eMMC RST pin could reply on PLT_RST so we could keep GPP B3 in VIH.
BUG=b:263548436
TEST=emerge-brask coreboot
Change-Id: Iffbc9dc932325cdd2176b36795a2ff1b3690fbf8
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72941
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
eMMC RST pin could reply on PLT_RST so we could keep GPP B3 in VIH.
BUG=b:263548436
TEST=emerge-brask coreboot
Change-Id: I610d53059e86945693bc5b3d7e43462e53640564
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72940
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add Raptor Lake (RPL) 28W dptf settings for Brya0
BUG=b:235311241
BRANCH=firmware-brya-14505.B
TEST=Built and tested on brya
Change-Id: I5d06c1ace5b481012ea39f2a57570eb6330479cb
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Add Raptor Lake (RPL) 28W dptf settings for Skolas
BUG=b:235311241
BRANCH=firmware-brya-14505.B
TEST=Built and tested on skolas
Change-Id: I4364ca6a50906c2a6dd0e754238264c680e7ebd0
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72728
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Update Power Limit1 (PL1) minimum value to 15W based on the Brya
design.
BRANCH=firmware-brya-14505.B
BUG=b:235311241
TEST=Built and tested on Brya system
Change-Id: Ifd5256221b82eae2cfe8009918f8ff4791751b4d
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72868
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Update Power Limit1 (PL1) minimum value to 15W based on the skolas
design.
BRANCH=firmware-brya-14505.B
BUG=b:235311241
TEST=Built and tested on Skolas system
Change-Id: I1027ca2bf2323ac959474ee6c38e47fa530113da
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72727
Reviewed-by: AlanKY Lee <alanky_lee@compal.corp-partner.google.com>
Reviewed-by: Vidya Gopalakrishnan <vidya.gopalakrishnan@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Update dptf thermal settings as per suggested by thermal team.
Control fan based on TSR sensors, not based on CPU sensor temperature
which changes too fast.
BRANCH=firmware-brya-14505.B
BUG=b:235311241, b:261749371
TEST=Built and tested on Brya system
Change-Id: I58bc7132086b0776ee191a242bd1302554f3854f
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72867
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Update dptf thermal settings as per suggested by thermal team.
Control fan based on TSR sensors, not based on CPU sensor temperature
which changes too fast. This change is based on the discussion on
bug:235311241 comment#7.
BRANCH=firmware-brya-14505.B
BUG=b:235311241, b:261749371
TEST=Built and tested on Skolas system
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Change-Id: Ibeddce61b0d73d82a85f486e7cb5cbfa9568953c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71692
Reviewed-by: AlanKY Lee <alanky_lee@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Vidya Gopalakrishnan <vidya.gopalakrishnan@intel.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Constitution will use SOLDERDOWN. Add memory.c to override baseboard.
Add mem_parts_used.txt and generate dram_id.generated.txt and
Makefile.inc
Memory:
SAMSUNG K4U6E3S4AB-MGCL
MICRON MT53E1G32D2NP-046 WT:B
BUG=b:267539938
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
Change-Id: Id879b2a7491f29e9fca903dcf3c022ec8ffffab4
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72775
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add EC_HOST_EVENT_USB_MUX to MAINBOARD_EC_S0IX_WAKE_EVENTS for
brask. Without it EC won't send host event to wake AP when USB
MUX is changed during S0ix. It's there for brya but missing
for brask.
BUG=b:267573651
TEST=emerge-brask coreboot
Signed-off-by: Derek Huang <derekhuang@google.com>
Change-Id: Id08d9aec9ab3566176369f2ca25cd00b9f0a0ca5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Add SoC config and .early_init = 1 in I2C1
BUG=b:263060849
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I661bdee6c7b9e6ea4cd0ab2006967d7c7ddd0f67
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72872
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
|
|
1. Add fw_config:STORAGE_UFS & STORAGE_NVME to switch storage.
2. rp11 off change to on.
BUG:b:263846075
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I35c02ac9cbb8442d7b4aae57f6c7b576b2b5f77b
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72090
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Create the aurash variant of the brask reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:263691099
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_AURASH
Change-Id: I595102778071f822c5cf69ceadeed174e5ea4836
Signed-off-by: Zoey Wu <zoey_wu@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72837
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Intel ADL-P USB Type-C ports are not compatible with Parade PS8815
retimer on USB U1/U2 transition. The usb_lpm_incapable config is
used to disable USB U1/U2 transition for these Type-C ports.
This patch add usb_lpm_incapable config for the following variants
with PS8815 retimer:
- kinox MLB: C0
- volmar DB: C1
- osiris MLB: C0/C1
- mithrax DB: C1
- felwinter DB: C1
- taeko DB: C1
- gimble DB: C1
- gimble4es DB: C1
- taniks DB: C1
- marasov DB: C2
- gaelin MLB: C0/C1
- skolas DB: C1
- skolas4es DB: C1
- brya0 DB: C1
BUG=b:253402457
TEST=Plug in device and check LPM sysfs nodes are disabled
localhost ~ # cat /sys/bus/usb/devices/2-X/power/usb3_hardware_lpm_u1
disabled
localhost ~ # cat /sys/bus/usb/devices/2-X/power/usb3_hardware_lpm_u2
disabled
Change-Id: Ie9246ff7908887404f49ec10ee781c8cba410557
Signed-off-by: Ron Lee <ron.lee@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Create the constitution variant of the brask reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:267539938
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_CONSTITUTION
Change-Id: Idb6089561d3aa5aac4448f9d46347c731f027e9c
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72730
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ELAN updated the datasheet, the HID/I2C protocol's T3 delay
time is 150ms now. Modify the kano's delay time to follow
the requiremnet.
BUG=b:247944006
TEST=Manually checked touchscreen works after reboot and suspend.
Change-Id: I42a7737060a82c0b27717f1510b8ec64abd1465a
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paz Zcharya <pazz@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
1. Enable Cnvi BT Audio Offload feature and also
configure the virtual GPIO for CNVi Bluetooth I2S pads.
2. According to the SOC_GPIO_Table_20230116,
Change GPIO GPP_D15, GPP_D16 to NC.
BUG=b:264834572
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I4901c8cd660f2d47018e4cccdb67f666f0800423
Signed-off-by: Jamie chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72035
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
This variant was added without a devicetree, so add the board
specific devicetree according to schematic_20230110.
BUG=b:263060849
BRANCH=None
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: Ie05c152a20953e3e2d5f4ba5f9c00160a3e418e1
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
|
|
NVMe PCIe 9-12 using clk_src1 and clk_req2 mapping to hardware design,
Due to inconsistency between PMC firmware and FSP, we need to set
clk_src to clk_req number, not same as hardware mapping in coreboot.
Then swap correct setting to clk_src=1,clk_req=2 in mFIT.
BUG=b:265720813
TEST=build firmware and veirfy suspend function on DUT.
Cq-Depend: chrome-internal:5351299
Change-Id: Ia057dfa98cb9293d9e212edb4e4ac198e94e8985
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72051
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn off camera power during S0ix to improve power consumption.
BUG=b:265754302
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Ie2b300783adfc1cab30bc897d086a3674436724a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The patch disables Tccold Handshake to prevent possible display
flicker issue for skolas board. Please refer to Intel doc#723158
for more information.
BUG=b:221461379
BRANCH=firmware-brya-14505.B
TEST=Boot to OS on Skolas, verify upd setting.
Change-Id: Ic184a61c27abd729667cd181d8f9954f58b67856
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68636
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ADL-N 15W CPU thermal settings.
BUG=b:265101768
TEST=emerge-nissa coreboot
Change-Id: I325704d6fc4ddaf56eaddd6a69bc619588df99cd
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71860
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Vidya Gopalakrishnan <vidya.gopalakrishnan@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This is regarding issues observed on multiple Brya and Nissa
variant such as Skolas and Nivviks. Issue is that once coreboot
sets GPE_EN bit for the GPIO pin and locks it, kernel is not able
to change the control bit. Hence kernel is not able to control the
IRQ on the pin when required.
This issue was root caused to the patch which was setting GPE_EN
bits for the GPIOs before locking.
Ref: commit 38b8bf02d820
("intelblocks: Add function to program GPE_EN before GPIO locking")
This patch skips the locking for GPP_F14 to allow kernel to
configure it later during reboot or shutdown as required.
BUG=b:254064671
BRANCH=None
TEST=Shutdown works on Skolas and Brya board with the patch.
Signed-off-by: Maulik Vaghela <maulikvaghela@google.com>
Change-Id: I7e4a6ac4668028bcd5fa400b9aa8eccf36a79620
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72648
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is an existing issue for skolas boards where board wakes up
from shutdown immediately due to touchpad wake signal.
This issue was root caused to the patch which was setting GPE_EN
bits for the GPIOs before locking.
Ref: commit 38b8bf02d820 ("intelblocks: Add function to program GPE_EN before GPIO locking")
Later issue was found to be with GPP_F14 configuration for skolas
boards. While shutting down, kernel is not able to disable IRQ for
touchpad due to GPE_EN register getting locked and it is preventing
shutdown of the board.
This patch skips the locking for GPP_F14 to allow kernel to
configure it later.
BUG=b:254064671
BRANCH=None
TEST=Shutdown works on Skolas board with the patch.
Nissa Bug: 234097956
Signed-off-by: Maulik Vaghela <maulikvaghela@google.com>
Change-Id: I09cf1af1f5ab11b06073755374ee8a306984d557
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72426
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the rcomp, dqs and dq tables based on the schematic.
BUG=b:264340545
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I82ca8aa9c3535983d5c506c15dbc69e7be926fa0
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Marx Wang <marx.wang@intel.com>
|
|
Change-Id: Id8e1a52279e6a606441eefe30e24bcd44e006aad
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69815
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Update the mem_parts_used.txt, generate Makefile.inc and
dram_id.generated.txt for this part.
DRAM Part Name ID to assign
MT62F1G32D2DS-026 WT:B 4 (0100)
K3KL8L80CM-MGCT 4 (0100)
H58G56BK7BX068 4 (0100)
BUG=b:259467147
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Change-Id: I204e871129a1b15d7c373d579e10a7b9ab6deabe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71906
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This reverts commit 197d550d069f918698fa7cd8dda73e09fbfda30c.
Reason for revert: breaks TBT and TypeC display on Brya0
Bug=265375098
Branch=firmware-brya-14505.B
Test=Build and boot Skolas board with Brya0 image. Test TBT
and TypeC display functionality.
Change-Id: Ia0283b023949476e90edff7151d605fa36331bfd
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72081
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
1. Enable multiple GPIOs to support the touch panel.
2. Add I2C setting for touch panel.
BUG=b:260818082, b:264812909
BRANCH=firmware-brya-14505.B
TEST=emerge-brask coreboot
Change-Id: I2b805d1960f8b4e3e27f1af02f9c4d31f973288f
Signed-off-by: Mike Shih <mikeshih@msi.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Wlan power enable pin is changed from EN_PP3300_WLAN to SLP_SUS_L.
Remove unused RTD3 driver.
BUG=b:263448873
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I22448a8cb28ddadb93b114c096e364980feab6fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71693
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change skips the MBP HOB creation since coreboot doesn't
use it and also helps to reduce the boot time by ~10msec.
Boot time data:
Before:
* 955:returning from FspSiliconInit 897,278 (33,603)
After:
* 955:returning from FspSiliconInit 864,543 (21,273)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ia97cca560869fcfd55e65c2e1719cceec6f3ab7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71873
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow hardware design to correct aux setting on USB-C ports to
fix DP monitor can not output data through type-C port 0
USB-C port 0 did not have retimer.
USB-C port 1 have retimer.
USB-C port 0 AUX_DC_P connect to GPP_E22.
USB-C port 0 AUX_DC_N connect to GPP_E23.
BUG=b:263212450
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
DP monitor display normally
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I3af7522f7b6477edcd88004ce1d5f86aeebe3393
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71222
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Exposing the GPIOs via an ACPI PowerResource and the _CRS results in the
OS driver and ACPI thinking they own the GPIO. This can cause timing
problems because it's not clear which system should be controlling the
GPIO.
Previously, we flagged as an error any device which set the
'has_power_resource' flag but did not set 'disable_gpio_export_in_crs.'
There's no reason to require explicit disablement however, so drop the
superfluous 'disable' flag, and change the _CRS generation to check if
the GPIOs will be exported via the 'has_power_resource' flag instead.
BUG=b:265055477
TEST=build/boot skyrim, dump SSDT and verify touchscreen GPIOs only
listed under PRx, not under _CRS.
Change-Id: I837ae6c6fe4b8e1c4e10686406cba06bdb7759d2
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
<gpio.h> chain-include <soc/gpio.h>.
Change-Id: Ia57d5cd33c70b6a755babd4db56c64c0e3666f9f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Configure GPIOs based from EE.
BUG=b:263060849
BRANCH=None
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I5cfaa8fce6df7f09b744fb3e0b7b1d5b6acdc79b
Signed-off-by: jamie_chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
|
|
BUG=b:252792591
BRANCH=firmware-brya-14505.B
TEST=On-screen text message seen during MRC training on skolas
with a few extra patches
Change-Id: I41c9cccb09dea52e2318f8f9ebeeda3697a7b514
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71696
|
|
Disable devices in variant.c instead of adding probe statements to
devicetree because storage devices need to be enabled when fw_config is
unprovisioned, and devicetree does not currently support this (it
disables all probed devices when fw_config is unprovisioned).
BUG=b:263920313
TEST=Boot to OS on craask eMMC and NVMe SKUs with both unprovisioned
fw_config and fw_config set correctly.
Change-Id: I4167ee4d00b9ae8fe074c6f5e7a2d5a7382bfe6d
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Disable devices in variant.c instead of adding probe statements to
devicetree because storage devices need to be enabled when fw_config is
unprovisioned, and devicetree does not currently support this (it
disables all probed devices when fw_config is unprovisioned).
BUG=b:251055188
TEST=Boot to OS on yaviks eMMC and UFS SKUs with both unprovisioned
fw_config and fw_config set correctly.
On UFS SKU with fw_config set, eMMC no longer shows up in lspci.
(On eMMC SKU, UFS and ISH were already disabled by the coreboot PCI scan
so there's no change in behaviour.)
Change-Id: I31402cb49cffefd98b6fed971f249528448b1d0d
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Add new memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
1) Samsung K3KL8L80CM-MGCT
2) Hynix H58G56BK7BX068
3) Micron MT62F1G32D2DS-026 WT:B
4) Micron MT62F512M32D2DR-031 WT:B
BUG=b:264340545
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I699070596a77c975254660a1ba74b0f40026186d
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add the first version DPTF parameters.
BUG=b:264217345
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I55a3066ef61ce461f40b425a6549d083c29256e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71634
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Kyle Lin <kylelinck@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Disable touch panel power for non-touch sku by fw_config TOUCH field.
BUG=b:263452842
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I4736f94481512806377b733b26fdc7290046c555
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71691
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kyle Lin <kylelinck@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust LAN LED config to 0x060f.
BUG=b:246657849
TEST=emerge-brask coreboot
Change-Id: Idd5ed2bf7eb4ee5990f2a842cba43f967ae3825e
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71698
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
|
|
Adjust LAN LED config to 0x060f.
BUG=b:239513596
TEST=emerge-brask coreboot
Change-Id: I17b844b89569fb7653454fd08782fc961c715817
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71697
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
|
|
Follow thermal table from thermal team.
1. Enable TS3 thermal sensor.
2. Set TS3 passive policy to 63.
3. Set TS3 critical policy to 73.
4. Modify TSR2 passive policy to CPU.
BUG=b:263554342
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: Ia1fcaee15a8b58b755ce0a48a1978e795b66efd7
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71658
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: AlanKY Lee <alanky_lee@compal.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add ACPI DmaProperty for gladios.
BUG=b:239513596
TEST=Verified SSDT on gladios unit.
Before:
Scope (\_SB.PCI0.RP01)
{
Device (RLTK)
{
Name (_HID, "R8168") // _HID: Hardware ID
Name (_UID, 0xD0E889DD) // _UID: Unique ID
Name (_DDN, "Realtek r8168") // _DDN: DOS Device Name
Name (_ADR, 0x00000000) // _ADR: Address
Name (_PRW, Package (0x02) // _PRW: Power Resources for Wake
{
0x07,
0x03
})
}
}
After:
Scope (\_SB.PCI0.RP01)
{
Device (RLTK)
{
Name (_HID, "R8168") // _HID: Hardware ID
Name (_UID, 0xD0E889DD) // _UID: Unique ID
Name (_DDN, "Realtek r8168") // _DDN: DOS Device Name
Name (_ADR, 0x00000000) // _ADR: Address
Name (_PRW, Package (0x02) // _PRW: Power Resources for Wake
{
0x07,
0x03
})
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("70d24161-6dd5-4c9e-8070-705531292865"),
Package (0x01)
{
Package (0x02)
{
"DmaProperty",
One
}
}
})
}
}
Change-Id: I1c4f6ff7b3eda114f4f365a963c089fe584d8aee
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71699
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This bit is dropped in factory. All skus can use table ID_0.
BUG=b:251287101
TEST=build passed.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I4298376899f881dd2265aef5a0bbc5bcc46728a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71690
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When EC_GOOGLE_CHROMEEC_INCLUDE_SSFC_IN_FW_CONFIG is enabled and
SSFC is not set, it will treat missing SSFC as zero, so Kano needs
to set the ov2740 to 0 to avoid probing wrong mipi camera.
Before patch
>fw_config match found: UFC=UFC_MIPI_OVTI2740
>fw_config match found: AUDIO=MAX98373_NAU88L25B_I2S
>fw_config match found: AUDIO=MAX98373_NAU88L25B_I2S
>fw_config match found: AUDIO=MAX98373_NAU88L25B_I2S
>fw_config match found: UFC=UFC_MIPI_OVTI2740
>fw_config match found: ZYDRON_UFC=UFC_MIPI_HI556
>fw_config match found: UFC=UFC_MIPI_OVTI2740
>fw_config match found: STYLUS=STYLUS_PRESENT
After patch
>fw_config match found: UFC=UFC_MIPI_OVTI2740
>fw_config match found: AUDIO=MAX98373_NAU88L25B_I2S
>fw_config match found: AUDIO=MAX98373_NAU88L25B_I2S
>fw_config match found: AUDIO=MAX98373_NAU88L25B_I2S
>fw_config match found: UFC=UFC_MIPI_OVTI2740
>I2C: 00:20 disabled by fw_config
>fw_config match found: UFC=UFC_MIPI_OVTI2740
>fw_config match found: STYLUS=STYLUS_PRESENT
BUG=b:262939431
TEST=Boot on kano and check functional with ov2740 camera.
Change-Id: I46fac6c820d6006956680a07198db82225630905
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Modify NVMe clkreq pin to GPP_D7 from GPP_D6.The design change is for
commonality of GPIO settings. To reserve craask GPIO table and add
craaskneto/craaskino's NVMe GPIO setting. In the change, clkreq# will
be 2 and clksrc is still 1.
BUG=b:259211172
TEST=Verify on reworked craask DUT to boot up from NVMe.
Change-Id: If45c1a87144d5370b1ca2525295fb7947639362f
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71170
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set fingerprint control GPIO to NC by HW design.
BUG=b:264340020
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I304862f0dd201da100b89c79a473eb116fc8263e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71650
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
Create the omnigul variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:263060849
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_OMNIGUL
Change-Id: I6b4123db9cb77dc050a81f1cb83ef10e2fbffe8d
Signed-off-by: jamie_chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This reverts commit 96d9b756690839c17b307a93b8a1898bd1c02ff5.
Reason for revert: Merged out of order, broke tree
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Iac2d78f2d6c687f52dc720e8d8dcb5cf7a171c9d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71280
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:252792591
BRANCH=firmware-brya-14505.B
TEST=On-screen text message seen during MRC training on skolas
with a few extra patches
Change-Id: I41c9cccb09dea52e2318f8f9ebeeda3697a7b513
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
In next phase, yaviks will remove external fivr. Use the board version
to config external fivr for backward compatibility and show message.
BUG=b:263842258
TEST=build, boot to OS, suspend/resume work normally.
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Id85570046c5b8e9d90a112793c1ec8604e6bf533
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Adjust audio codec i2c timing to 399 kHz.
BUG=b:263050944
TEST=FW_NAME=lisbon emerge-brask coreboot
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: I8495a88f2034e5e4ccf28ff53c81e0d6561e2e0f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Adjust audio codec i2c timing to 399 kHz.
BUG=b:262959586
TEST=FW_NAME=gladios emerge-brask coreboot
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: I2f621e3af39fb40ab270c9de35d51dd43147b8f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add wifi sar table for kuldax
BUG=b:248367859
BRANCH=firmware-brya-14505.B
TEST=emerge-brask coreboot-private-files-baseboard-brya coreboot
chromeos-bootimage
Change-Id: I5ade590c739aae391e47e8bb66ee03c086e8d56e
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71270
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fast VMode nmakes the SoC throttle when the current exceeds the I_TRIP
threshold.
BUG=b:252966799
BRANCH=firmware-brya-14505.B
TEST=Verify that the feature is enabled by reading from fsp log
Change-Id: I15c3eea6ebb7f104bce0ba8cb544ecde7f488343
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
On Marasov, the ISH is running closed source firmware, so the ChromeOS
security requirements specify it must be behind an IOMMU. Add
DmaProperty to the ISH _DSD on Marasov.
TEST=Kernel marks ISH (PCI device 12.0) as untrusted, and changes the
IOMMU group type to "DMA". Also, device still goes to S0i3.
Before:
$ cat /sys/devices/pci0000\:00/0000\:00\:12.0/untrusted
0
After:
$ cat /sys/devices/pci0000\:00/0000\:00\:12.0/untrusted
1
Change-Id: I4b65b8909c41b06852fe7771375029bd2e76e111
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71263
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
For marasov, the ISH main firmware will be included in the CSE region in
flash instead of loading it from rootfs. So remove the ISH
firmware-name.
TEST=Boot to OS on Marasov UFS SKUs. Check ISH firmware is not
loaded by kernel, and device still goes to S0i3.
Change-Id: I278e5d403ef9515e538a527f43949e505d750bb1
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71261
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyle Lin <kylelinck@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
|
|
Kano didn't use SSFC in mass production, however
Zydron needs SSFC for 2rd source mipi instead of fw_config.
BUG=b:262939431
TEST=Boot to OS and check functional with ov2740/hi556 camera.
Change-Id: Idb2a35d67af0b5a7dedc66b0f7eccd8a3b4612d1
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
|
|
Use get_wifi_sar_fw_config_filename to remove the duplicate code.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I04176fee373e534d42c72506df73a092ad55e65b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Use get_wifi_sar_fw_config_filename to remove the duplicate code.
WIFI_SAR_CBFS_DEFAULT_FILENAME is not exist, so return the non-exist
id has the same outcome.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ib7a764d8cc3160c26abad9c1757812b955bef066
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Use get_wifi_sar_fw_config_filename to remove the duplicate code.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ifde714c19f7ab9fe08f870060037db190a80dbd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
The currently assigned ACPI HID 'PNP0C50' is not a valid per Windows
WHQL validation tests. To ensure compatibility with both Windows and
Linux, set the HID to 'SYNA0000' and CID to 'ACPI0C50' as previously
done for other boards (eg, google/lulu).
TEST=untested on brya, but tested under Windows/Linux on all other
boards in the tree using Synaptics touchpads.
Change-Id: Ia9351185b918f2d6f2d2be110b88e8310d37a03f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Extend sd_hold to meet touchpad/touchscreen SPEC.
touchscreen:
tHD > 0.2 us
touchpad:
0.3 us < tHD < 0.9 us
After applied the change, the tHD meets reqirement.
touchscreen:
0.056 us -> 0.28 us
touchpad:
0.056 us -> 0.384 us
BUG=b:263340540
TEST=build and measure the timing meet SPEC
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I172d2ec8a4b16d8005106f55a37795cc72d69e98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Configure eMMC DLL tuning values for Pujjo board Kioxia sku.
BUG=b:261676386
TEST=Use the value to boot on Pujjo successfully.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I46991f26571771620dcd94b90e1112484ade63bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Adjust I2C speed for codec, TPM, touchpad, touchscreen.
BUG=b:260565911
TEST=Built and verified adjusted I2C speed
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Idcec6e401992d30dff01940c50473cba48cffc19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
|
|
Enable wifi sar function for yaviks.
Use the fw_config to separate SAR setting for different wifi card.
BUG=259199095
TEST=build, enabled iwlwifi debug, and check dmesg
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I3ced65368ee66e084e58d66cff8f75147f665d71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Update SX9324 RegProxCtrl0 register settings based on tunning value
from P-sensor vendor.
BUG=b:242662878
TEST=i2cdump -y -f 13 0x28 on Pujjo
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: If471a6fee5a3daeac1958709415b2d5e1329b81b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
BUG=b:260565911
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Id5a73126737a3abbe6f0ef37276ce20f687b47fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70236
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
Disable unused PCIE8 for fix system can not enter S0ix completely.
BUG=b:261915226
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I06f8bd06e1fe92c03bd5625a41469830ce37a11c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70660
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Correct touchscreen setting to make touchscreen function workable.
BUG=b:260565911
BRANCH=firmware-brya-14505.B
TEST=Built and verified touchscreen function
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Ia98deae65ef0e2f501457331144b044e07431a3c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
