summaryrefslogtreecommitdiff
path: root/src/mainboard/google/brox/variants
AgeCommit message (Collapse)Author
2024-07-12mb/google/brox/var/lotso: Add FW_CONFIG for FPWentao Qin
This patch adds FW_CONFIG to accommodate different Lotso BoM components across various SKUs. 1. Fingerprint sensor - FP Present/Absent BUG=b:350360162 BRANCH=None TEST=Boot image on SKU2 and check FP working. Change-Id: I1ee5fcd1c29099bdbee741ef76c00cf45fcc1189 Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83388 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-07-08mb/google/brox/var/lotso: Update DTT settings for thermal controlKun Liu
update DTT settings for thermal control,according to b:348285763#comment6. BUG=b:348285763 TEST=emerge-brox coreboot Change-Id: I67e16a2596884d501273a5787119406dff7a20f9 Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83304 Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-07-04mb/google/lotso: Add hid report address for gt7986uKun Liu
Add hid report address for gt7986u. BUG=b:342932183 BRANCH=None TEST=Verify touchscreen work normal. Change-Id: I464c2691505083314528519f608108c8a31e6cc0 Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83201 Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-07-03mb/google/brox/var/lotso: Tune I2C frequency for 400 kHzJing Tong
Before: I2C0 - 401kHz I2C4 - 405kHz After: I2C0 - 392kHz I2C4 - 395kHz HW: Change R8409/R8411 to 33ohm. BUG=b:349743464,b:349735055 TEST=emerge-brox sys-boot/coreboot Test pass by EE Change-Id: I985837b1b80e973f148529b446905580c0f95e98 Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83290 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
2024-06-28mb/google/brox/variants/brox/fw_config.c: Remove unused macroElyes Haouas
Change-Id: I8ce94c8bc7ed137eaace12d6cb0befa6c0d39a37 Signed-off-by: Elyes Haouas <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82925 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yidi Lin <yidilin@google.com> Reviewed-by: Eric Lai <ericllai@google.com>
2024-06-27mb/google/brox/var/lotso: GPP_B14 used for buzzerJing Tong
ALC257 does not supoort built-in digtal buzzer, So use external pwm to PCBEEP for beep sound. BUG=b:346956771 BRANCH=None TEST=emerge-brox coreboot sys-boot/chromeos-bootimage firmware-shell: devbeep -> can output beep normally. Change-Id: If924f9f27f229420e78015f418a97b2d5daf62e5 Signed-off-by: Jing Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83147 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-06-26mb/google/brox: Disable Touchscreen for hardware board version 1Karthikeyan Ramasubramanian
On board version 1 and later, touchscreen is not stuffed. Hence configure the relevant GPIOs as not connected, disable the concerned I2C bus in the devicetree as well as SoC chip config for board version 1. BUG=b:347333500 TEST=Build Brox BIOS image and boot to OS. Ensure that there are no peripherals detected in I2C 1 bus through i2cdetect tool. Ensure that no touchscreen devices are exported through ACPI SSDT table. Ensure that other I2C peripherals - eg. Trackpad and Ti50 are functional. Ensure that the device is able to suspend and resume for 25 cycles. Change-Id: Ia0578b90b0e8158ae28bcc51add637844ba6acf6 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83199 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-06-25lotso: Update board type to BOARD_TYPE_ULT_ULXKun Liu
Update board type to BOARD_TYPE_ULT_ULX BUG=b:348147663 BRANCH=none TEST=Built and compare the results of command 'dmidecode --type 17 | grep Speed' [Before] Speed: 8400 MT/s Configured Memory Speed: 6400 MT/s [After] Speed: 8400 MT/s Configured Memory Speed: 5200 MT/s Change-Id: I049d7c19424f41e83480f4b80bafd6ef8b9e30f6 Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83191 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
2024-06-24mb/google/brox: Add support for batteryless bootingShelley Chen
Set PsysPL2 and PsysPL3 in addition to making adjustments to PL2 and PL4 in order to prevent brownouts when we don't have a battery or have an empty battery at boot time. BUG=b:335046538,b:329722827 BRANCH=None TEST=flash Able to successfully boot on a SKU1 with 45W, 60W+ adapters and SKU2 with a 60W or higher type C adapter. 30W is still being worked on. Change-Id: Ie36f16b2c938dce29cd2130a86fc8c08f5ba0902 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83087 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-06-20mb/google/brox/var/lotso: enable CNVi bluetoothJing Tong
Lotso's WIFI_BT is same design as brox, copy from brox. BUG=b:339612353 TEST=emerge-brox coreboot chromeos-bootimage and boot on Change-Id: I030e306dc5d9d3fcb6314bc491dbf5c9ae60bcb7 Signed-off-by: Jing Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83126 Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
2024-06-19mb/google/brox/var/lotso: Update devicetree settingJian Tong
Based on schematics NB7228A_LOTSO_INTEL_MB_PROTO_20240521A_BOM.pdf update devicetree settings. BUG=b:333494257 TEST=emerge-brox coreboot chromeos-bootimage and boot on Change-Id: Ic9a7a9062f5c6e45c5bd9617f3b2a0634b8dc1db Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83051 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-06-19mb/google/brox/var/lotso: Update verb table from ALC256 to ALC257Jing Tong
Update verb table provided by Realtek on 20240614. BUG=b:344471736 TEST=emerge-brox sys-boot/coreboot sys-boot/chromeos-bootimage Device list: cat /sys/bus/hdaudio/devices/ehdaudio0D0/chip_name ALC257 cat /sys/bus/hdaudio/devices/ehdaudio0D0/vendor_name Realtek Headphone detection: Event: time 1718633617.056092, type 5 (EV_SW), code 2 (SW_HEADPHONE_INSERT), value 1 Event: time 1718633621.471708, type 5 (EV_SW), code 2 (SW_HEADPHONE_INSERT), value 0 Event: time 1718633623.898046, type 5 (EV_SW), code 2 (SW_HEADPHONE_INSERT), value 1 Event: time 1718633625.743663, type 1 (EV_KEY), code 115 (KEY_VOLUMEUP), value 1 Event: time 1718633625.743678, type 1 (EV_KEY), code 115 (KEY_VOLUMEUP), value 0 Change-Id: Idde8963de9302849f87b7c262f17d9c9d99b46dc Signed-off-by: Jing Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83109 Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-06-17Revert "mb/google/brox/var/lotso: enable CNVi bluetooth"Matt DeVillier
This reverts commit 0e0bc618e3ed1888ac140010057dc7485443c3c2. Reason for revert: Merged out of order, breaks tree Change-Id: I22bd85a2008db471177257a8b779c06898b1010c Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83105 Reviewed-by: Martin L Roth <gaumless@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-06-17mb/google/brox/var/lotso: enable CNVi bluetoothJian Tong
Lotso's WIFI_BT is same design as brox, copy from brox. BUG=b:339612353 TEST=emerge-brox coreboot chromeos-bootimage and boot on Change-Id: I3946297db7f10a31570f773bdc5665f9f472c9fe Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83053 Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2024-06-12mb/google/brox: Generate RAM IDsKun Liu
Generate RAM IDs for K3KL6L60GM-MGCT H9JCNNNBK3MLYR-N6E K3KL8L80DM-MGCU MT62F1G32D2DS-023 WT:C H58G56BK8BX068 BUG=b:333494257 BRANCH=None TEST=Run part_id_gen tool without any errors Change-Id: I7a240a263816193b9f3d418385c1673e9d3f89db Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83040 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
2024-06-12mb/google/brox/var/lotso: Update gpio settingJian Tong
Based on lotso EVT schematics update gpio settings. GSPI0_CS0_L -> NF7 GSPI0_MISO -> NF7 GSPI0_MISO -> NF7 GPP_F18 -> EDGE_SINGLE BUG=b:333494257 TEST=emerge-brox coreboot chromeos-bootimage and boot on Change-Id: I12d84538566c4d51fe346eb5609e55d91ddafbea Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/83039 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
2024-06-07mb/google/brox/var/brox: update thermal settings to start fan earlySumeet Pawnikar
Current existing temperature thresholds of TSR1 sensor are set at 60C to start fan. Due to this CPU gets hot and temperature goes over 80C. In this situation, fan does not even start to lower down CPU temperature. With updated new settings based on tuning from thermal team, start fan early at 40C for TSR0 and TSR1 so the CPU temperature stays below 80C. BUG=b:339493551 TEST=Built and tested on google/brox board Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Change-Id: I4765c13c10e436733d8c9d017085968daa561ccc Reviewed-on: https://review.coreboot.org/c/coreboot/+/82784 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-06-06mb/google/brox/var/lotso: Add dq map settingJian Tong
Based on lotso EVT schematics add dq map settings. BUG=b:333494257 TEST=emerge-brox coreboot chromeos-bootimage and boot on Change-Id: I4f03e8a90522cbf2fe06f4160414202dcc4a2199 Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82600 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Dengwu Yu <yudengwu@huaqin.corp-partner.google.com>
2024-06-05mb/google/brox/var/lotso: Update gpio settingJian Tong
Based on lotso EVT schematics update gpio settings. BUG=b:333494257 TEST=emerge-brox coreboot chromeos-bootimage and boot on Change-Id: I13485cc7ccd8b15352f5e21ad9336aa2b3d35749 Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82573 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Shelley Chen <shchen@google.com>
2024-05-23mb/google/brox/var/brox: Remove mux references from typec portPrashant Malani
The Type-C kernel driver no longer programs the AP mux, as of https://review.coreboot.org/c/coreboot/+/82077. So remove device references to the TCSS Mux control device from the Type-C port driver. This eliminates the following kernel error which was observed as a result of the kernel trying to program muxes it no longer has control over: [ 4.618600] cros-ec-typec GOOG0014:00: Failed to get mux info for port: 0, err = -95 [ 4.618608] cros-ec-typec GOOG0014:00: Configure muxes failed, err = -95 BUG=b:341331428 TEST=Run system reboot; configure mux kernel errors no longer seen. Change-Id: I93e498b12b109c0e649a23a4a49868976a9ee06b Signed-off-by: Prashant Malani <pmalani@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82599 Reviewed-by: Caveh Jalali <caveh@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-05-22Revert "mb/google/brox: Update verb table to fix headset detection"Terry Cheong
This reverts commit f867c9c5473156617691d78350c362cd993bfcdd. The new verb table breaks external mic detection on brox. Revert and use old verb tables instead. BUG=b:330433089 BRANCH=main TEST=Verified headset on Brox When connected to audiojack in power_save state of legacy hda driver, headset is detected and audio is resumed. Change-Id: I0d8c092de6166b2c62f5ecc3deaf4960128e6106 Signed-off-by: Terry Cheong <htcheong@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82273 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-05-21mb/google/brox/var/greenbayupoc: Update verb table from ALC256 to ALC236Wu Garen
On GreenbayPOC, HDA Codec used is ALC236, different with Brox (ALC256) Update to Realtek provided verb table for ALC236 audio codec. BUG=b:336967284 TEST=Verified headset and audio workable on DUT with "rec" and "aplay" command. Change-Id: I9fbe57a0acab20387754f6b6cb5705e34c1c149b Signed-off-by: Wu Garen <wu.garen@inventec.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82413 Reviewed-by: Ivan Chen <yulunchen@google.com> Reviewed-by: Derek Huang <derekhuang@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-05-14mb/google/brox/var/greenbayupoc: Add vbt from broxEren Peng
Copy the data.vbt from brox to greenbayupoc BUG=b:326413034 TEST=emerge-brox coreboot chromeos-bootimage, flash and boot on DUT Change-Id: I1e8101519ab2ecbb4654c20485fbe83c90656e4d Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82108 Reviewed-by: Derek Huang <derekhuang@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-05-14mb/google/brox/var/greenbayupoc: Update devicetree and gpio settingsEren Peng
Based on latest schematics GREENBAY_0412.SCH update the gpio and devicetree settings. BUG=b:326413034 TEST=emerge-brox coreboot chromeos-bootimage, flash and boot on DUT Cq-Depend:chrome-internal:7218819 Change-Id: I59f25b8abb7dd8a2dff7ff567b231bddc9db8455 Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82093 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Derek Huang <derekhuang@google.com>
2024-05-13mb/google/brox: Disable c1 state auto-demotionAshish Kumar Mishra
Disable c1 state auto-demotion support for brox BUG=None BRANCH=None TEST=Boot brox and verify in fsp debug logs Change-Id: I18d40cd721d46fce4702cf1a943583cd41c03cf4 Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82104 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-05-12mb/google/brox/var/greenbayupoc: Configure board for SODIMM useEren Peng
Configure SODIMM settings for greenbayupoc. The SODIMM settings are copied from mainboard/google/brya/variants/baseboard/brask/memory.c. BUG=b:336955026, b:332230842 TEST=emerge-brox coreboot chromeos-bootimage, flash and boot to OS using Hynix HMAG56EXNSA051N 4G and Micron MTA8AFT1G64HZ-3G2R1 8G SODIMM. Change-Id: I1552cadfa81c48fe561947ded078bcca2e6bc6ad Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82085 Reviewed-by: Derek Huang <derekhuang@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kapil Porwal <kapilporwal@google.com>
2024-05-08mb/google/brox: Fix the pad reset config for WLAN Wake interruptKarthikeyan Ramasubramanian
Update the pad reset config for WLAN Interrupt from PLTRST to DEEP so that it can still act as a wake source during S3 suspend. BUG=b:336398012 TEST=Build Brox BIOS image and boot to OS. Suspend to S0ix & S3 and wakeup successfully using Wake on WLAN. 268 | 2024-05-07 13:56:44-0700 | S0ix Enter 269 | 2024-05-07 13:57:07-0700 | S0ix Exit 270 | 2024-05-07 13:57:07-0700 | Wake Source | GPE # | 3 271 | 2024-05-07 13:59:01-0700 | ACPI Enter | S3 273 | 2024-05-07 13:59:26-0700 | Wake Source | PME - WIFI | 0 274 | 2024-05-07 13:59:26-0700 | ACPI Wake | S3 275 | 2024-05-07 13:59:26-0700 | Wake Source | GPE # | 3 Change-Id: Ie0d6e6c8fefdd081e252ea99d6e3c559a5330b0e Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82234 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-05-08mb/google/brox/var/brox: increase PsysPmax from 21.5W to 208WLawrence Chang
According to Brox HW design, the PsysPmax is supposed to be 208W. This patch changes PsysPmax setting from 21.5W to 208W. Change-Id: I43f4b00a54dc0dfe6bd690492f9ef92698c9b903 Signed-off-by: Lawrence Chang <lawrence.chang@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82185 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Shelley Chen <shchen@google.com>
2024-04-30mb/google/brox: Add 20K pulldown to GPP_D14Shelley Chen
GPP_D14 is floating when ISH is not being used and wasting power. Add pulldown to prevent this from happening. BUG=b:336654954 BRANCH=None TEST=emerge-brox coreboot chromeos-bootimage make sure OS boots up HW team validated that power usage is 20 mW lower Change-Id: I4e19e98fa31022ece66a47402a2a4461b430ef70 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82096 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-04-29mb/google/brox: Fix the pad reset config for Touchpad interruptKarthikeyan Ramasubramanian
Update the pad reset config for Touchpad Interrupt from PLTRST to DEEP so that it can still act as a wake source during S3 suspend. BUG=b:336398012 TEST=Build Brox BIOS image and boot to OS. Suspend to S3 and wakeup using Trackpad. 246 | 2024-04-25 16:55:18-0700 | ACPI Enter | S3 247 | 2024-04-25 16:55:34-0700 | ACPI Wake | S3 248 | 2024-04-25 16:55:34-0700 | Wake Source | GPE # | 67 249 | 2024-04-25 17:00:38-0700 | ACPI Enter | S3 250 | 2024-04-25 17:00:47-0700 | ACPI Wake | S3 251 | 2024-04-25 17:00:47-0700 | Wake Source | GPE # | 67 Also suspend to S0ix and wakeup using Trackpad. Change-Id: If1a275e42c6c7ad743eedc9cd3320776008bfd62 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82067 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com>
2024-04-25mb/google/brox/var/lotso: Add fw_config field for storagetongjian
Add STORAGE_UNKNOWN, STORAGE_UFS, STORAGE_NVME for storage fw_config field to prevent depthcharge build break. BUG=b:333494257 TEST=emerge-brox coreboot depthcharge sys-boot/chromeos-bootimage Change-Id: Idb62e3f37e1480979ae529692455beb533434520 Signed-off-by: tongjian <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/82056 Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2024-04-19mb/google/brox/variants/lotso: add missing hda_verb.hFelix Held
Commit 00b40090aecf ("mb/google/brox: Move hda verb to variant dir") introduces a variant-specific file for the HDA verb tables, which commit 1bf0c3f1897c ("mb/google/brox: Create lotso variant") was missing which caused the build to fail when both patches were submitted. To fix the tree, add this file to the newly created lotso variant. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: I8a85115a204d9d9447a58da71eb65b1de963023d Reviewed-on: https://review.coreboot.org/c/coreboot/+/82014 Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2024-04-19mb/google/brox: Create lotso variantKun Liu
Create the lotso variant of the brox reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.5.0). BUG=b:333494257 BRANCH=None TEST=util/abuild/abuild -p none -t google/brox -x -a make sure the build includes GOOGLE_LOTSO Change-Id: I5939127f9e6abe5b792c0627d9d67e739b27083b Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/81817 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-04-19mb/google/brox: Move hda verb to variant dirtongjian
Others variant boards might use diff HDA Codec, so move hda verb to brox variant dir. BUG=b:314702466 BRANCH=None TEST=emerge-brox sys-boot/coreboot sys-boot/chromeos-bootimage Device list: cat /sys/bus/hdaudio/devices/ehdaudio0D0/chip_name ALC256 cat /sys/bus/hdaudio/devices/ehdaudio0D0/vendor_name Realtek Headphone detection: evtest 8 Event: time 1713404716.656768, type 5 (EV_SW), code 2 (SW_HEADPHONE_INSERT), value 1 Event: time 1713404716.656768, -------------- SYN_REPORT ------------ Event: time 1713404722.802661, type 5 (EV_SW), code 2 (SW_HEADPHONE_INSERT), value 0 Event: time 1713404722.802661, -------------- SYN_REPORT ------------ Change-Id: Id987c248c37dc8bdc63be7a2513fa8997b5ddc33 Signed-off-by: tongjian <tongjian@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/81945 Reviewed-by: Poornima Tom <poornima.tom@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2024-04-19mb/google/brox/var/greenbayupoc: Add fw_config field for storageEren Peng
Add STORAGE_UNKNOWN, STORAGE_UFS, STORAGE_NVME for storage fw_config field to prevent depthcharge build break. BUG=b:333325006 TEST=emerge-brox coreboot depthcharge with no errors Change-Id: I0e220787d6ac73ec8fa2469ed958981d0801920e Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/81833 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ivan Chen <yulunchen@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Derek Huang <derekhuang@google.com>
2024-04-17mb/google/brox: Enable SAGvAshish Kumar Mishra
Enable SaGv support for brox BUG=None BRANCH=None TEST=Boot brox with SAGv enabled and verify in fsp debug logs Change-Id: I80c44e7df1d75732c6982b27e44ecd6060b1b3f1 Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/81556 Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-04-15mb/google/brox: Create greenbayupoc variantEren Peng
Create the greenbayupoc variant of the brox reference board by copying the template files to a new directory named for the variant. BUG=b:329530883 BRANCH=None TEST=util/abuild/abuild -p none -t google/brox -x -a make sure the build includes GOOGLE_GREENBAYUPOC. Change-Id: I90936d97b41e59c49dd92997146caf580bce1f4f Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/81565 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Shelley Chen <shchen@google.com>
2024-04-12mb/google/brox: Initialize NOTE_BOOK_MODE GPIOShelley Chen
The GPIO for NOTE_BOOK_MODE has changed from GPP_B17 to GPP_E9. Also initializing it (if ISH is enabled) to be NF2 (ISH_GP4). Also took the liberty of alphabetizing all the ISH GPIOs to they're easier to search through. BUG=b:316421831 BRANCH=None TEST=emerge-brox coreboot chromeos-bootimage Make sure that brox device still boots up with this change. Change-Id: I4a091b58deb855c7a7f1489a9506db2f821503b7 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/81789 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-04-02mb/google/brox: Enable PMC pins to work with PDAshish Kumar Mishra
Enable SMLINK1 interface for PMC-PD communication to configure Type-C muxes. Refer RPL EDS vol 1: 765585. BUG=b:327622474 BRANCH=None TEST=Boot image on SKU2 and check PMC-PD working. Change-Id: Ia678d291e7a14aefe09026e70478fea3f68c8e10 Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/81207 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Deepti Deshatty <deepti.deshatty@intel.com>
2024-04-01mb/google/brox: Configure ISH device based on FW_CONFIGKarthikeyan Ramasubramanian
ISH Firmware name needs to be configured only when full sensing capabilities are enabled through ISH_ENABLE FW_CONFIG. Similarly DMA property needs to be added only when UFS is enabled through STORAGE_UFS FW_CONFIG. Hence configure the ISH device at run-time based on FW_CONFIG. BUG=b:319164720 TEST=Build Brox BIOS image and boot to OS. Change-Id: I678416acd48e03ab77ae299beae6e295a688b8df Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/81418 Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2024-03-27mb/google/brox: Fix GPE_EC_WAKE configurationKarthikeyan Ramasubramanian
Wake signal from EC is routed to GPP_D1 and hence GPE_EC_WAKE corresponds to GPE0_DW1_01. Fix GPE_EC_WAKE configuration. BUG=b:329026602 TEST=Build Brox BIOS image and boot to OS. Trigger suspend and wake up using EC generated events like AC connect/disconnect. Change-Id: Ifb89bd0de7b7fc316792e801ed5a1d3f25ca5b1c Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/81526 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Kangheui Won <khwon@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Keith Short <keithshort@chromium.org>
2024-03-21mb/google/brox: Configure I2C timing for I2C devicesIvy Jian
Configure I2C0/1 timing in devicetree to meet timing requirement. (THIGH(us) minimum is 0.6us). Before: I2C0 : THIGH(us) 0.595us I2C1 : THIGH(us) 0.582us After: I2C0 : THIGH(us) 0.673us I2C1 : THIGH(us) 0.666us Change-Id: I79af4fde4eb08d4eb896794756a633701bebb755 Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/81348 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2024-03-20mb/google/brox: support ISHLi Feng
Set FW_CONFIG bit 21 to enable ISH PCI device and define ISH main firmware name so ISH shim loader can load firmware from file system. ISH also need to be enabled if STORAGE_UFS is set. BUG=b:280329972 TEST= Set bit CBI FW_CONFIG bit 21 Boot Brox board, check that ISH is enabled and loaded lspci shows: 00:12.0 Serial controller: Intel Corporation Alder Lake-P Integrated Sensor Hub (rev 01). Change-Id: Iadc5108c62737d27642a6948c00b5c122541aaba Signed-off-by: Li Feng <li1.feng@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80773 Reviewed-by: Tanu Malhotra <tanu.malhotra@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Yuval Peress <peress@google.com>
2024-03-09mb/google/brox: Enable Wake on WLAN for SKU1Ashish Kumar Mishra
For SKU1, wake pin is WLAN_PCIE_WAKE_ODL. Update gpio config and corresponding ACPI for WoWLAN. BUG=b:327379404 BRANCH=None TEST=Boot image on SKU1 and check Wake on WLAN from S0ix. Change-Id: I04c35da2c9ac57cafdf7f7a35d83ab2e7a05fe4a Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80780 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com>
2024-02-20mb/google/brox: enable DPTF functionality for broxSumeet Pawnikar
Enable DPTF functionality for brox board BRANCH=None BUG=b:324360936 TEST=Built and tested on brox board Change-Id: I0315f7f45688ccc36d321d6be4fa4fac7559a16b Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80418 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2024-02-17mb/google/brox: Handle bluetooth enable on devicesAshish Kumar Mishra
For devices that require CNVi Bluetooth select WIFI_BT_CNVI in FW_CONFIG. Discrete Bluetooth devices need to select WIFI_BT_PCIE. BUG=b:319188820,b:325084796 BRANCH=None TEST=Boot image on SKU1,SKU2 and check BT devices enumerate. Change-Id: Iba008682fcfa7ddc1ec400649c8742c721666f1d Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80564 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-02-16mb/google/brox: Set PCH_EC_PCH_INT_ODL pin as IOAPICShelley Chen
Setting the EC interrupt GPIO as an APIC is able to solve many problems that we are currently seeing: 1. Routing through the APIC make the IRQ# associated with this pin unavailable to claim for other devices in the kernel. This is causing EC interrupts to not work. 2. Since EC interrupt are not working, we are not able to flash the EC from the DUT. 3. Also, the GPI_INT configuration does not allow us to set the polarity of the GPIO, which means that it is by default set as active high. As a result, we are seeing an excessive number of host command interrupts to the EC. This disappears when we change the configuration to APIC and set the polarity as INVERT. BUG=b:319129926,b:324707182 BRANCH=None TEST=1. After boot up, check if ec_cros_lpcs driver was successfully registered. Look for the following string: "cros_ec_lpcs GOOG0004:00: Chrome EC device registered" 2. Make sure can flash the EC image from the DUT 3. Make sure EC console is not getting continuous stream of host commands. Change-Id: I74bff88d2ddbaf1f4b085c31d582bd66e18c438a Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80467 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ashish Kumar Mishra <ashish.k.mishra@intel.corp-partner.google.com>
2024-02-13mb/google/brox: Set display output type for eDP panelMatt DeVillier
Set the display type for the LCD panel configured via the gfx/generic driver. This will ensure the correct DID/device address are generated in the SSDT. Change-Id: If63374329ed5eb4330517ca1bf2ba1ada24fa54a Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80244 Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Reviewed-by: Martin L Roth <gaumless@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-02-13mb/google/brox: Use name 'LCD0' for internal panel outputMatt DeVillier
The GMA driver generates the brightness controls expecting the name LCD0, so we need to use it here as well so that the DSDT and SSDT parts match. Change-Id: Id52f7c0e542423ba08eeed89bf9b171e540e10e4 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80243 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin L Roth <gaumless@gmail.com> Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
2024-02-09mb/google/brox: Initialize TCHSCR_RST_L to 0Shelley Chen
TCHSCR_RST_L signal was originally being configured to 1 in gpio.c but this was causing some leakage. Configuring it to 0 initially in romstage fixes this. Also, make sure that EN_PP3300_TCHSCR is initialized in romstage as well. BUG=b:322249892 BRANCH=None TEST=Make brox boots and touchscreen is still working Change-Id: I5bf1901a3a40a38237b950abcb758f96aebcc1cf Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80300 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-02-08mb/google/brox: Handle GPI_INT pin lower to GPI_WAKEAshish Kumar Mishra
In case where PAD_CFG_GPI_INT() is initialized with a pin value lower to PAD_CFG_GPI_IRQ_WAKE() for same GPIO community the set_ioapic_used() is only called for the PAD_CFG_GPI_IRQ_WAKE() pin. Due to this the IRQ associated with PAD_CFG_GPI_INT() is found free by find_free_unique_irq() during IRQ assignment and assigned to other pins which causes IRQ conflicts BUG=b:322984217 BRANCH=None TEST=Boot test on brox, check if correct IRQ assigned to EC Change-Id: I8c3d557e888b8d0ceac203f49b702910fba26d6d Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80334 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-02-05mb/google/brox: Fix the I2C configurationKarthikeyan Ramasubramanian
Update the I2C configuration to match the usage such that only required I2C controllers are enabled. BUG=b:319390850 TEST=Build Brox BIOS image and boot to OS. Ensure that only the required I2C controllers are enabled. Change-Id: I9f24beb9ef587163362cc6ded88efb05be1329b9 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80303 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-02-01mb/google/brox: Enable HDA Codec ALC256Poornima Tom
On Brox, HDA Codec used is ALC256. Add verb table for the same. Also, add the related device tree changes for HDA related registers. Realtek High Definition Audio Configuration- Version : 5.0.3.1 BUG=b:317398558 BRANCH=None TEST=verified HDA on Brox. HDA Sound cards detected. Headphone working verified. Device listed under sysfs as below: cat /sys/bus/hdaudio/devices/ehdaudio0D0/chip_name ID 256 cat /sys/bus/hdaudio/devices/ehdaudio0D0/vendor_name Realtek Change-Id: I1edd5aee053debe39b34048266703031c088cd00 Signed-off-by: Poornima Tom <poornima.tom@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79723 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-26mb/google/brox: Enable TouchscreenShelley Chen
BUG=b:300690448,b:319393777 BRANCH=None TEST=tested on a device with i2cdetect Also tested with evtest and make sure Wacom is listed Change-Id: I4f528b0d778c8c4a4e83774d5c167ccb2d6afd9a Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79895 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-26mb/google/brox: Remove CNVi BluetoothShelley Chen
This is causing an assertion error on the devices that don't have CNVi enabled because CNVi is hidden behind a FW_CONFIG flag in the overridetree now. BUG=b:319188820 BRANCH=None TEST=emerge-brox coreboot chromeos-bootimage make sure we can boot to kernel on device. Change-Id: Ifcfbc04825d4d4e7f2874a4c52f9c5cf3e657856 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80211 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-25mb/google/brox: Switch EC INT and WAKE GPIOsShelley Chen
There was a mistake in the gpio spreadsheet provided by the HW team and the GPIO assignments for the EC INT and WAKE signals got switched from what it was in the schematics. The correct assignments are: GPP_D0 = EC_PCH_INT_ODL GPP_D1 = EC_PCH_WAKE_ODL BUG=b:311450057,b:300690448 BRANCH=None TEST=emerge-brox coreboot Will try to boot OS image on device and see if there are any ec errors. Change-Id: I02057aeb5d82218dbbe4c939d4feb87a4d3da678 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79886 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-24mb/google/asurada to cyan: Rename Makefiles from .inc to .mkMartin Roth
The .inc suffix is confusing to various tools as it's not specific to Makefiles. This means that editors don't recognize the files, and don't open them with highlighting and any other specific editor functionality. This issue is also seen in the release notes generation script where Makefiles get renamed before running cloc. Signed-off-by: Martin Roth <gaumless@gmail.com> Change-Id: I5855f49984db59d786decad6142e3525b146a573 Reviewed-on: https://review.coreboot.org/c/coreboot/+/80105 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
2024-01-23mb/google/brox: Move cnvi to overridetreeShelley Chen
We need to disable the cnvi device when pcie wifi is enabled, so need to use the FW_CONFIG defined in the overridetree for this. BUG=b:311450057,b:300690448,b:319188820 BRANCH=None TEST=This will be tested on the device when received Change-Id: If9e861db37e321fd69c09f9b4aafa2e212f92caa Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79898 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-23mb/google/brox: Enable WLAN on root port 5Shelley Chen
BUG=b:311450057,b:300690448,b:319188820 BRANCH=None TEST=test on device with lspci & make sure can see the Intel Network controller Change-Id: I361bef13ebd073b6fccb729a1960d3832cf2681a Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79888 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2024-01-20mb/google/brox: enable WIFI_SARShelley Chen
Add get_wifi_sar_cbfs_filename(). This function uses the FW_CONFIG for WIFI to choose the right wifi_sar hex file. Below is the file mapping: wifi_sar_0.hex = wifi6 wifi_sar_1.hex = wifi7 BUG=b:319302319 BRANCH=None TEST=emerge-brox coreboot chromeos-bootimage Change-Id: I212c80412141e7770a512bd8ccf4111963bab395 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/80085 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-18mb/google/brox: Fix user facing camera acronymShelley Chen
I got confused and used UFS (User Facing Side) for the User Facing Camera (UFC) in the FW_CONFIGs. Change references of the camera from UFS --> UFC. BUG=b:300690448 BRANCH=None TEST=None. The camera has not been enabled yet. Change-Id: I4f8240ae51aad1e077f325a9eab5a2a92f1402cb Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79997 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-17mb/google/brox: Move storage devices to overridetreeShelley Chen
These are specific to the brox board, so moving devices to the brox variant. BUG=b:311450057,b:300690448,b:319058143 BRANCH=None TEST=emerge-brox coreboot chromeos-bootimage will check if this helps detect the storage device in the factory Change-Id: I18d096040c293abfd4cd0b1bb5f50ba6dcc2e183 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79995 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2024-01-17mb/google/brox: Set up FW_CONFIGShelley Chen
Brox project has FW_CONFIG bits already set up in the project file for the retimer and for storage, so make sure that the brox device tree matches those settings. BUG=b:311450057,b:300690448,b:319058143 BRANCH=None TEST=emerge-brox coreboot chromeos-bootimage will check if this helps detect the storage device in the factory Change-Id: Iaf43003b7e8210eee9016d779839d7048c15825f Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79854 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-13mb/google/brox: Enable Elan trackpadShelley Chen
BUG=b:311450057,b:300690448 BRANCH=None TEST=to be tested on a device with i2cdetect Change-Id: If6da1c722e87a50c6d422b300f16a52d884fa08f Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79892 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2024-01-13mb/google/brox: Configure vGPIOs for NVMeShelley Chen
This is needed for NVMe to work when PCIe device is connected to the CPU side of RPL soc. BUG=b:311450057,b:300690448, b:319058143 BRANCH=None TEST=Tested on device and was able to boot to the OS Change-Id: Ic8a1fdcedf2ec6c7bf1dd00e02ef7c13e9338aac Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79857 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2024-01-13mb/google/brox: Disable package c state demotionShelley Chen
This needs to be disabled for RPL otherwise we'll hit the assertion: [EMERG] ASSERTION ERROR: file 'src/soc/intel/alderlake/fsp_params.c', line 1066 There is a comment in the referenced file/line in the assertion that says that "C state demotion must be disabled for Raptorlake J0 and Q0 SKUs." So, disabling it. BUG=b:311450057,b:300690448 BRANCH=None TEST=Tested that we didn't hit this assertion on the device after this change Change-Id: Ib7b2484de2d84c980550fd951f1e30efab0ee197 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79855 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-09mb/google/brox: Fix error in DDR DQS configShelley Chen
The DQS mapping for DIMM idx 6 was discovered to be incorrect to what was in the schematics. Correcting the mistake in this CL. BUG=b:311450057,b:300690448 BRANCH=None TEST=tested on device and it passed memory training Change-Id: I21f50e2f5b4fae09725c1c7532636ed1cc1a9043 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79843 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
2023-12-28mb/google/brox: Add new GFX devicesShelley Chen
Add GFX devices for DDI (eDP and HDMI) and TCP (USC C0 and C2 ports). Copied the PLD placements from USB PLDs. BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: Ic39916819f64ede1c80eccfd05ba4916b9f285af Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79731 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
2023-12-22mb/google/brox: Fix config errors with 8 GPIOsShelley Chen
Some GPIOs were not configured correctly according to the HW spreadsheet provided by the HW team. * GPP_B5/GPP_B6 use NF1, not NF2 * GPP_B23 should use NF2, no GPI * GPP_D11 should be set to NC * GPP_E21/22 should be using NF (previous NC) * GPP_F17 is a GPO * GPP_F18 should be an interrupt, not a NF BUG=b:300690448,b:316180020 BRANCH=NONE TEST=emerge-brox coreboot Change-Id: I9e1e62adb79bd7fdab935afdbf2d23f9061b88aa Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79705 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2023-12-22mb/google/brox: Align GPIO reset with HW spreadsheetShelley Chen
Did a pass through HW team's brox speadsheet and aligned the gpio.c file with it. The changes in this CL are to fix the pad's reset field as needed. See "Intel SoCs" section in https://doc.coreboot.org/getting_started/gpio.html for reset definitions. BUG=b:300690448,b:316180020 BRANCH=NONE TEST=emerge-brox coreboot Change-Id: I4285136184c648adb9dc97748bd6b01cba3f8ddd Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79579 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2023-12-22mb/google/brox: Fix pulls as necessaryShelley Chen
Did a pass through HW team's brox speadsheet and aligned the gpio.c file with it. The changes in this CL include fixing the pulls for GPIOs as necessary, making sure that it matches what is in the HW team's spreadsheet. BUG=b:300690448 BRANCH=NONE TEST=emerge-brox coreboot Change-Id: Ie50cb3c6fc85f1633c1afd1330c0e040e04b0ec1 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79704 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-22mb/google/brox: Change unused GPIOs to NCShelley Chen
Did a pass through HW team's brox speadsheet and aligned the gpio.c file with it. The changes here include changing the pad config to NC because it is not being used in ChromeOS. BUG=b:300690448 BRANCH=NONE TEST=emerge-brox coreboot Change-Id: I15471e4d7ff25c858b05ef024f15ca7c0b9e598e Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79703 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-21mb/google/{brya,brox,rex}: Update ec_sync wake capabilityMark Hasemeyer
Some of the boards use the EC_SYNC pin to wake the AP but do not advertise the pin as wake capable in the CREC _CRS resource. Relevant boards were determined through empirical testing and inspection of gpio configuration. Update the ACPI tables for rex, brya, and brox based boards to advertise their EC_SYNC pin as wake capable. BUG=b:243700486 TEST=-Dump ACPI and verify ExclusiveAndWake share type is set when EC_SYNC_IRQ_WAKE_CAPABLE is defined -Wake Aviko via keypress and verify chromeos-ec as wake source -Wake Screebo via lid open and verify chromeos-ec as wake source Change-Id: I5828be7c9420cab6ae838272c8301c302a3e078c Signed-off-by: Mark Hasemeyer <markhas@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79374 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Kapil Porwal <kapilporwal@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-12-20mb/google/brox: Enable FSP UPD LpDdrDqDqsReTrainingIvy Jian
FSP default value for LpDdrDqDqsReTraining is 1. For boards that didn't set LpDdrDqDqsReTraining to any value, 0 was being assigned and it caused black screen issue. BUG=b:311450057 BRANCH=NONE TEST=emerge-brox coreboot Change-Id: I4a009076e50408a4f7ff16ddc96a0f2e47b09470 Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79646 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-13mb/google/brox: Generate RAM ID for supported memory partIvy Jian
Add the MICRON MT62F1G32D2DS-023 WT:B RAM part for brox: DRAM Part Name ID to assign MT62F512M32D2DR-031 WT:B 0 (0000) H9JCNNNBK3MLYR-N6E 0 (0000) MT62F1G32D4DR-031 WT:B 1 (0001) MT62F1G32D2DS-023 WT:B 2 (0010) BUG=b:311450057,b:315913909 BRANCH=None TEST=Run part_id_gen tool without any errors Change-Id: Id120a5eb311d8299a8e59d2c1658fe0742e93934 Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79459 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2023-12-08mb/google/brox: Update configuration for USB portsIvy Jian
Update brox devicetree based on the latest schematics. - Configure typeC to EC mux ports settings. - Configure USB2/USB3 ports settings. - Configure TCSS ports settings. BUG=b:311450057 BRANCH=None TEST=emerge-brox coreboot Change-Id: Iac5a2e8be6cea64f107d267d4cf71529f08bb63d Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79391 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-06mb/google/brox: Generate RAM IDs for two modulesIvy Jian
Add the support LP5 RAM parts for brox: 1. HYNIX LPDDR5 6400 2GB H9JCNNNBK3MLYR-N6E 2. MICRON LPDDR5 6400 4GB MT62F1G32D4DR-031 WT:B DRAM Part Name ID to assign H9JCNNNBK3MLYR-N6E 0 (0000) MT62F1G32D4DR-031 WT:B 1 (0001) BUG=b:311450057 BRANCH=None TEST=Run part_id_gen tool without any errors Change-Id: Ib17f26a310435e37088191594863a645aa751440 Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79392 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2023-12-05mb/google/brox: Fix memory configShelley Chen
Fix up the memory config for brox based on the schematics. Also, since memory training needs to happen in romstage, initializing the MEM_STRAP & MEM_CH_SEL gpios for use in romstage. Also consolidating the GPIOs needing to be initialized in romstage into the baseboard gpio.c file. BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: I17615cda7df10e73e49fb49f736728787ef7625d Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79355 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
2023-12-01mb/google/brox: Update storage settings for SSD and UFSIvy Jian
Brox has SSD and UFS storage per different SKU. 1. Set SSD on CPU PCIe port (PCIEX4_A) and configure related gpio settings according to the schematic. 2. Enable UFS, also enable ISH since it is PCI function 0, required for UFS function 7 to be enabled. 3. Set unused SRCCLKREQ signals to NC. 4. Remove unused gpio settings in variant gpio table to prevent unexpected overrides. BUG=b:311450057 BRANCH=None TEST=emerge-brox coreboot Change-Id: I88922bcfa13652006aa10078c3c444624fd4575e Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79295 Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-29mb/google/brox: Fix configuration for TPMShelley Chen
On Brox, TPM is using i2c4 and GPP_E2, so modifying the Kconfig to reflect this. Also, fixing up the TPM entry in the device tree. Making sure that the GPIO for GSC_PCH_INT_ODL is set correctly. BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: I0ecaa6fcfc05c3c2e55f857d7a4e59fe46096bb5 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79102 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
2023-11-18mb/google/brox: Fix GPIO assignments in gpio.hShelley Chen
Assigning the macros in gpio.h to the correct GPIOs. Also, fixing GPE configurations so that they are mapped to the proper wake sources (GPP_B, D, E groups). BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: I6320cd98e560e514e63c52e173cb7923cfd1cdee Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/78952 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2023-11-14mb/google/brox: Set unstuffed straps to NCShelley Chen
All of these signals have net names, but are actually unstuffed, so we have to set them to NC. BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: I27d8b7cd02aefb49a2dc031a30eb0d1e8aa9faa9 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/78951 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2023-11-09mb/google/brox: Remove use of EC_IN_RW_OD GPIOShelley Chen
Later GSCs don't need a EC_IN_RW GPIO anymore, so removing the use of this for get_ec_is_trusted(). BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: I29f94969e9f2c1f239d9f9655f39b8410296f695 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/78950 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2023-11-08mb/google/brox: Configure early GPIOs in bootblockShelley Chen
Some GPIOs (like WP and GSC) need to be configured in bootblock. Making sure that they get configured earlier for this. BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: I8dd4853bc05b954f47d858d87ea2aed48e4b8074 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/78943 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-08mb/google/brox: Correcting GPIOs based on latest schematicsShelley Chen
There are some inaccuracies in arbitrage. This is the first pass at correcting the incorrectly generated configs. I also tried to update the "No heuristic was found useful" comment generated by arbitrage into something more useful (ie: the appropriate NFs). BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: I836565e09a3e0b25746b3e2f9ed6610eaacf7e97 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/78942 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-10-26mb/google/brox: Add Arbitrage generated gpio.c fileShelley Chen
Checking in gpio.c generated by arbitrage. Used this command line to generate: arb export-coreboot-gpio --refdes=U1 brox:proto1_20231017 BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: I1098bd4cfde393ed9e78cd90158c3534fdf0dc09 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/78657 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-10-13mb/google/brox: Create new Brox baseboardShelley Chen
This CL is just getting the initial brox framework to get the baseboard building. Copied files from brask baseboard and tried to remove contents of some files like the device tree and memory IDs. Added support for memory part "MT62F512M32D2DR-031 WT:B", mapped to DRAM ID 0. BUG=b:300690448 BRANCH=None TEST=./util/abuild/abuild -p none -t GOOGLE_BROX -x -a Change-Id: I929b465646ac4c69d4bab33ce23848c7b1fa0f98 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/78009 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-24 11:38:39 +0000