| Age | Commit message (Collapse) | Author |
|---|
|
Create an event handler for the PEWAKE# GPIO and notify the device
driver to wake up the device.
BUG=b:301150499
TEST=Compiled and tested on google/redrix:
1. Enable runtime suspend for linux mtk_t7xx driver
2. Wait for device to enter suspended state
3. Modem should be able to wake up driver, e.g. on SIM card insert/eject
The interrupts should show up under /proc/interrupts as ACPI:Event
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Change-Id: I32257689da85ea71f9de781093b3ede0cfe70a0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78297
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After commit e12b313844da ("drivers/pc80/rtc/option.c: Allow CMOS
defaults to extend to bank 1"), Thinkpad X200 with
CONFIG(STATIC_OPTION_TABLE) can no longer resume from s3 (detected via
bisect).
Further inspection shows that DRAM training result of GM45 is stored
in CMOS above 128 bytes in raminit_read_write_training.c, for s3 resume
to restore, but it will be erased by sanitize_cmos(), which now clears
both bank 0 and bank 1, leaving only "untrained" result restored, so s3
resume will fail.
However, resetting CMOS seems unnecessary during s3 resume. Now,
cmos_need_reset will be negated when acpi_is_wakeup_s3() returns true.
Tested: Thinkpad X200 with CONFIG(STATIC_OPTION_TABLE) can resume from
s3 again with these changes.
Change-Id: I533e83f3b95f327b0e24f4d750f8812325b7770b
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78288
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Bayhub BH720 eMMC bridge is a fixed internal device, and needs to
me marked as non-removable in order for Windows to properly recognize/
utilize the device. Add the necessary ACPI to be generated at runtime.
TEST=build/boot/install Win11 on google/kahlee (liara)
Change-Id: I0815abf1d2dc5cfe785dc04670ab91f2a6a1af23
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Support embedding a second FSP-M/FSP-S binary for an SoC that can
select one at runtime.
Comet Lake v1 and v2 are different steppings of the same SKUs, but they
require different FSP binaries. Supporting both in a single build
requires embedding both FSPs and selecting one at runtime based on the
CPUID. This is desirable for a product that may have different CPU
steppings but is not otherwise differentiated enough for a separate
firmware build.
An SoC can select PLATFORM_USES_SECOND_FSP to indicate that two FSP-M/
FSP-S binaries are required. Implement soc_select_fsp_m_cbfs() and
soc_select_fsp_s_cbfs() to choose one based on platform-specific
criteria. For Comet Lake, the first FSP is CML v1 and the second is
CML v2, but in principle a platform could define any meaning for the
first and second FSP.
FSP-T is not affected, only one FSP-T can be embedded if FSP_CAR is
used.
Only one set of FSP headers is used, which is sufficient for Comet Lake
v1/v2; their headers are equivalent.
ADD_FSP_BINARIES, FSP_USE_REPO, and FSP_FULL_FD are supported for both
sets of FSP-S/FSP-M but cannot be configured separately, both use the
same configuration.
Change-Id: Ied4c6c49a6bdf278238272edd47a2006258be8e5
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78344
Reviewed-by: Michał Kopeć <michal.kopec@3mdeb.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
This consolidates the bp, tb, cmp, srp0 and srp1 variables under the new
spi_flash_bpbits struct to allow treating them as one unit in the
refactoring to follow.
Change-Id: I2a1a77fb73047df733498c0fa8b8de1153c3b09e
Signed-off-by: Daniel Gröber <dxld@darkboxed.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42113
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch introduces a new coreboot table entry named
"has_external_display" to understand if external display is attached.
This information is useful to prevent graceful shutdown by payload
when the LID is closed but an external display is present.
This piece of the information will be gathered by coreboot and passed
into the payload using this new entry aka external_display because
payload (i.e., deptcharge) doesn't have any other way to determine
if external display is available.
BUG=b:299137940
TEST=Able to build and boot google/rex.
w/o this patch:
LID closed and external display attached (HDMI) in developer mode
(GBB 0x39):
> System is powered off by depthcharge
w/ this patch:
LID closed and external display attached (HDMI) in developer mode
(GBB 0x39):
> Booted to OS and device is alive/usable
Change-Id: I0fa7eee4c5a50371a7a66c6ca1ac2c7d046d010b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77796
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit updates the port select bit definitions for the
TRANS_DDI_FUNC_CTL registers in the Intel GMA driver to accommodate
the changes introduced since TGL SoC.
Specifically, the following changes were made:
- Updated the DDI select bit definitions from 3-bits (bit 28-30) to
4-bits (bit 27-30).
- Introduces `INTEL_GMA_VERSION_2` config to accommodate the port and
pipe related differences between previous generation GMA register
(TRANS_DDI_FUNC_CTL) to the current generation GMA register.
This commit backports the change from the following upstream patch:
https://patchwork.freedesktop.org/patch/msgid/20190713010940.17711-3-
lucas.demarchi@intel.com
BUG=b:299137940
TEST=Able to build and boot google/rex.
Change-Id: I815ffa90c2e235afd70baa7e3837e1f9af89b1b0
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Separate these so a mainboard can describe a PS/2 keyboard without a
PS/2 mouse or vice-versa.
Librem 11 has a PS/2 keyboard for the volume keys, but does not have a
PS/2 mouse, and the presence of a mouse device can cause the cursor to
appear on the desktop incorrectly.
ps2_controller.asl remains since many boards include it, it now just
includes the two new files.
Change-Id: I13a4c2caf8dc9e5004b775dc0a9ac2488e39f184
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78096
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add additional failure mode reporting to the TPM driver to provide
additional visibility into what failures are occurring.
BUG=b:296439237
TEST=Verify code paths on Skyrim, ensure behavior is unchanged.
BRANCH=None
Change-Id: I77a653201acf1bddc1ed1e2af701c8d3dd4f0606
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77491
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
Convert TPM functions to return TPM error codes(referred to as
tpm_result_t) values to match the TCG standard.
BUG=b:296439237
TEST=build and boot to Skyrim
BRANCH=None
Change-Id: Ifdf9ff6c2a1f9b938dbb04d245799391115eb6b1
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77666
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert hex print values to use the %#x qualifier to print 0x{value}.
BUG=b:296439237
TEST=build and boot to Skyrim
BRANCH=None
Change-Id: I0d1ac4b920530635fb758c5165a6a99c11b414c8
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78183
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enables correct identification of boards using rt5650 codec for either
speaker or headset output (or both) by SOF Windows drivers.
Change-Id: Ied9717955fcfca33bd63a34f3f6961deb045239c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78092
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enables correct identification of boards using rt1019 speaker amplifier
by SOF Windows drivers.
TEST=tested with rest of patch train
Change-Id: I550dc8614e6e21d6d8715c12b7a4af35117497b5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Allows device to be hidden from OS (Windows) via devicetree 'hidden'
keyword.
TEST=tested with rest of patch train
Change-Id: I81482bd19e24627cab80deed2b9057f45b6ac0a0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78037
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make naming convention consistent across all functions return values.
BUG=b:296439237
TEST=Boot to OS on Skyrim
BRANCH=None
Change-Id: If86805b39048800276ab90b7687644ec2a0d4bee
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77536
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
tis_init calls into tis_probe and returns an error or success, simplify
the call stack by removing the current tis_init implementation and
renaming tis_probe to tis_init.
BUG=None
TEST=builds
Change-Id: I8e58eda66a44abf5858123cf9bcf620626f1b880
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Update an invalid error message printed when the timer expires.
BUG=None
TEST=None
BRANCH=None
Change-Id: If6d35290e9cb8281cd33892dc052f49277474a59
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add some noop device_operations for devices below chip drivers/pc80/tpm
in the case CONFIG_TPM is unset. This avoids the warning "... missing
read_resources" when probing all devices for resources.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ibc37642a8b5f37b95c648141e03025a04ffa36bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77386
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
x86 pre-memory stages do not support the `.data` section and as a
result developers are required to include runtime initialization code
instead of relying on C global variable definition.
To illustrate the impact of this lack of `.data` section support, here
are two limitations I personally ran into:
1. The inclusion of libgfxinit in romstage for Raptor Lake has
required some changes in libgfxinit to ensure data is initialized at
runtime. In addition, we had to manually map some `.data` symbols in
the `_bss` region.
2. CBFS cache is currently not supported in pre-memory stages and
enabling it would require to add an initialization function and
find a generic spot to call it.
Other platforms do not have that limitation. Hence, resolving it would
help to align code and reduce compilation based restriction (cf. the
use of `ENV_HAS_DATA_SECTION` compilation flag in various places of
coreboot code).
We identified three cases to consider:
1. eXecute-In-Place pre-memory stages
- code is in SPINOR
- data is also stored in SPINOR but must be linked in Cache-As-RAM
and copied there at runtime
2. `bootblock` stage is a bit different as it uses Cache-As-Ram but
the memory mapping and its entry code different
3. pre-memory stages loaded in and executed from
Cache-As-RAM (cf. `CONFIG_NO_XIP_EARLY_STAGES`).
eXecute-In-Place pre-memory stages (#1) require the creation of a new
ELF segment as the code segment Virtual Memory Address and Load Memory
Address are identical but the data needs to be linked in
cache-As-RAM (VMA) but to be stored right after the code (LMA).
Here is the output `readelf --segments` on a `romstage.debug` ELF
binary.
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x000080 0x02000000 0x02000000 0x21960 0x21960 R E 0x20
LOAD 0x0219e0 0xfefb1640 0x02021960 0x00018 0x00018 RW 0x4
Section to Segment mapping:
Segment Sections...
00 .text
01 .data
Segment 0 `VirtAddr` and `PhysAddr` are at the same address while they
are totally different for the Segment 1 holding the `.data`
section. Since we need the data section `VirtAddr` to be in the
Cache-As-Ram and its `PhysAddr` right after the `.text` section, the
use of a new segment is mandatory.
`bootblock` (#2) also uses this new segment to store the data right
after the code and load it to Cache-As-RAM at runtime. However, the
code involved is different.
Not eXecute-In-Place pre-memory stages (#3) do not really need any
special work other than enabling a data section as the code and data
VMA / LMA translation vector is the same.
TEST=#1 and #2 verified on rex and qemu 32 and 64 bits:
- The `bootblock.debug`, `romstage.debug` and
`verstage.debug` all have data stored at the end of the `.text`
section and code to copy the data content to the Cache-As-RAM.
- The CBFS stages included in the final image has not improperly
relocated any of the `.data` section symbol.
- Test purposes global data symbols we added in bootblock,
romstage and verstage are properly accessible at runtime
#3: for "Intel Apollolake DDR3 RVP1" board, we verified that the
generated romstage ELF includes a .data section similarly to a
regular memory enabled stage.
Change-Id: I030407fcc72776e59def476daa5b86ad0495debe
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
_STR should return Unicode string. From ACPI spec:
6.1.10 _STR (String)
The _STR object evaluates to an Unicode string that describes the
device or thermal zone.
BUG=NA
TEST=Check the changed _STR in SSDT to see if Unicode() macro is used
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I1f4b55a268c1dadbae456afe5821ae161b8e15a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77695
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
This adds DRIVERS_INTEL_MIPI_SUPPORTS_PRE_PRODUCTION_SOC to provide
the option to load pre-production or production signed IPU FW from IPU
kernel driver.
BUG=None
TEST=Build rex and brya to check if the build passes without an
error.
Change-Id: Ib507bceb6fd85d8ed764df82db400526a10e4d6e
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77854
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The sta_himax83102 panel sometimes shows abnormally flickering
horizontal lines. The front gate output will precharge the X point of
the next pole circuit before TP term starts, and wait until the end of
the TP term to resume the CLK. For this reason, the X point must be
maintained during the TP term. In abnormal case, we measured a slight
leakage at point X. This is because during the TP term, the GPW does not
fully pull the VGL low, causing the TFT to not be closed tightly.
To fix this, we completely pull GPW to VGL before entering the TP term.
This will ensure that the TFT is closed tightly and prevent the abnormal
display.
BUG=b:299249186
BRANCH=corsola
TEST=FW Screen display normally
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I5dddaaa38917a65990c1474b657db5eb551940b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77692
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I42e995952a72a23a5f3aeadf428ad13f25546854
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Also move the semicolon on next line.
Change-Id: I68412407ec8c8f99c15f39b0ec08d4fb33eb1b3f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ic52f01d1d5d86334e0fd639b968b5eed43a35f1d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77633
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Parentheses are not required.
Change-Id: Iad1f766a3eb569af39030e43365e8a0a609f5944
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77706
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: I6ff11df45ddc396391efd651f9938e04646dc0d3
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77707
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This patch adds support for Intel WIFI-7 series PCIe based WLAN module.
Change-Id: Ia31fdb87e15b50471dc7664e42b1e2625ce1ac58
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Convert camel case macros to uppercase and underscore separated macros,
such as:
PCI_DID_CyP_6SERIES_WIFI -> PCI_DID_CP_6SERIES_WIFI
PCI_DID_TyP_6SERIES_WIFI -> PCI_DID_TP_6SERIES_WIFI
This makes the macros more consistent with the rest of the code and
easier to read.
Change-Id: I9c739aab93dc0d043a3c9d9ce799087952c1e20b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77644
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch refactors the existing MRC cache storing logic, which was
spread between the ROM and RAM stages, into a single early MRC cache
store stage. The only exception is when SoC user selects
FSP_NVS_DATA_POST_SILICON_INIT to store MRC cache from ramstage (after
FSP-S).
It reverts all the boot-state logic previously used to locate and store
MRC cache from NVS HOB into NVS because majority of the platform can
potentially use the early MRC cache store with improved memory caching
at the pre-RAM phase (with the ramtop implementation).
The only exception is the Xeon SP platform, which currently locates
the MRC cache post in FSP-S (at ramstage). Therefore, this patch
provides an API to the FSP 2.x silicon init code to perform late
storing of the MRC cache.
In majority cases the updated logic, the romstage (post FSP-M) will
attempt to save the MRC cache. Platform that selects
FSP_NVS_DATA_POST_SILICON_INIT config performs the same operation post
FSP-S. Depending on whether the MRC_STASH_TO_CBMEM config is
enabled, the MRC cache will either be written directly to NVRAM at the
romstage or stashed into CBMEM for a late NVRAM write at ramstage.
Below table captures the change in the boot state w/ and w/o this
patch for storing the MRC cache. Overall the goal is to ensure the
platform behavior is remain unchanged before and after this patch.
w/o this patch:
| | Save MRC | Finalize | Lock the |
| | Cache | MRC Cache | Boot Medium |
+-----------+----------------+----------------+----------------+
| MRC_WRITE | BS_OS_RESUME | BS_OS_RESUME | BS_ON_RESUME |
| NV_LATE | CHECK_ENTRY | CHECK_ENTRY | CHECK_EXIT |
+-----------+----------------+----------------+----------------+
| MRC_STASH | BS_DEV | BS_DEV | BS_DEV |
| TO_CBMEM | ENUMERATE_EXIT | ENUMERATE_EXIT | RESOURCES_ENTRY|
+-----------+----------------+----------------+----------------+
| FSP_NVS | BS_DEV_INIT | BS_DEV | BS_DEV |
| DATA_POST | CHIPS_EXIT | ENUMERATE_EXIT | RESOURCES_ENTRY|
| SILICON | | | |
| INIT | | | |
+-----------+----------------+----------------+----------------+
| Platform | BS_PRE | BS_DEV | BS_DEV |
| w/o above | DEVICE_ENTRY | ENUMERATE_EXIT | ENUMERATE_ENTRY|
| config | | | |
| (FSP 2.0 | | | |
| platforms | | | |
w/ this patch:
| | Save MRC | Finalize | Lock the |
| | Cache | MRC Cache | Boot Medium |
+-----------+----------------+----------------+----------------+
| MRC_WRITE | BS_OS_RESUME | BS_OS_RESUME | BS_ON_RESUME |
| NV_LATE | CHECK_ENTRY | CHECK_ENTRY | CHECK_EXIT |
+-----------+----------------+----------------+----------------+
| MRC_STASH | BS_DEV | BS_DEV | BS_DEV |
| TO_CBMEM | ENUMERATE_EXIT | ENUMERATE_EXIT | RESOURCES_ENTRY|
+-----------+----------------+----------------+----------------+
| FSP_NVS | Post FSP-S | BS_DEV | BS_DEV |
| DATA_POST | (ramstage) | ENUMERATE_EXIT | RESOURCES_ENTRY|
| SILICON | | | |
| INIT | | | |
+-----------+----------------+----------------+----------------+
| Platform | Post FSP-M | BS_DEV | BS_DEV |
| w/o above | (romstage) | ENUMERATE_EXIT | ENUMERATE_ENTRY|
| config | | | |
| (FSP 2.0 | | | |
| platforms | | | |
BUG=b:296704537
TEST=Able to build and boot google/rex without any boot time impact.
Change-Id: Id1e91d25916594f59d1e467a142f5042c6138b51
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77556
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This patch renames `SAVE_MRC_AFTER_FSPS` config to
`FSP_NVS_DATA_POST_SILICON_INIT` to highlight the violation in the Xeon
SP FSP implementation, where the FSP Silicon Init API produces
Non-Volatile Storage (NVS) instead of the FSP-Memory Init API.
According to the FSP 2.x specification (section 11.3), the FSP
populates the NVS data using the FSP_NON_VOLATILE_STORAGE_HOB and
expects the boot firmware to parse the FSP_NON_VOLATILE_STORAGE_HOB
after the FspMemoryInit() API in API mode.
However, not all Intel SoC platforms that support the FSP 2.x
specification adhere to this requirement. For example, the FSP binary
for XEON SP platform produces NVS data (aka
FSP_NON_VOLATILE_STORAGE_HOB) after the FspSiliconInit() API.
Therefore, attempting to locate NVS data after the FspMemoryInit() API
on these platforms would result in an error. The `save_mrc_data.c`
implementation provides the required hooks to locate the NVS post
FSP-Silicon Init and store into Non-Volatile Storage.
BUG=b:296704537
TEST=Able to build and boot Intel Xeon SP w/o any functional impact.
Change-Id: I815a64263fa1415bfe30bb3c1c35e4adee307e86
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Change-Id: Ic49cb6c67aa707efa6495788137b550683008868
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Add an option to invert write protect polarity for GL9750.
Change-Id: I5761f3066291a2400caecbecc79ae893f0a0c146
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77403
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds logic for logging the FW splash screen event to
the event log.
There could be three possible scenarios as below:
1. Platform w/o FW splash screen (i.e., either HAVE_FSP_LOGO_SUPPORT
or BMP_LOGO configs not enabled)
Expectation: Firmware Splash Screen (ELOG_TYPE_FW_SPLASH_SCREEN) not
present in the event log.
39 | 2023-08-27 12:42:54-0700 | System boot | 12
40 | 2023-08-27 12:42:54-0700 | ACPI Wake | S5
41 | 2023-08-27 12:42:54-0700 | Wake Source | Power Button | 0
2. Platform w/ FW splash screen (i.e., both HAVE_FSP_LOGO_SUPPORT
and BMP_LOGO configs are enabled)
Expectation: Firmware Splash Screen (ELOG_TYPE_FW_SPLASH_SCREEN) is
enabled in the event log.
34 | 2023-08-27 12:07:29-0700 | System boot | 11
35 | 2023-08-27 12:07:29-0700 | Firmware Splash Screen | Enabled
36 | 2023-08-27 12:07:31-0700 | ACPI Wake | S5
37 | 2023-08-27 12:07:31-0700 | Wake Source | Power Button | 0
3. Failed to render FW splash screen (due to any reason if FSP failed
to render the splash screen)
Expectation: Firmware Splash Screen (ELOG_TYPE_FW_SPLASH_SCREEN) is
disabled in the event log.
43 | 2023-08-27 13:06:10-0700 | System boot | 13
44 | 2023-08-27 13:06:10-0700 | Firmware Splash Screen | Disabled
45 | 2023-08-27 13:06:11-0700 | ACPI Wake | S5
46 | 2023-08-27 13:06:11-0700 | Wake Source | Power Button | 0
BUG=b:284799726
TEST=Verify that the event shows up in the event log when the user
selects the HAVE_FSP_LOGO_SUPPORT and BMP_LOGO configs to display
the firmware splash screen.
Change-Id: Ie9e09acff5443c31b881c300134bc0bb06c490c6
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
'useable' -> 'usable'.
Change-Id: Iad2e1ef97a5c98ffa6f33806bce5b77722e687e8
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: I9804fcd9076b5a4813f099db0852a5af5ac36609
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77523
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: Idc38c759489976cbdf51d9c4bb950ef6d470b93a
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: Id7634099e40c0bf97944be124b494c41d6335ad7
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
These Kconfig options were being used basically as #define statements,
which is unnecessary. This isn't a good use of Kconfig options and would
be better just as #defines if actually needed.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If987b50d8ec3bb2ab99096e5e3c325e4d90a67a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
When LZMA compression is selected, then it's not needed to check if LZ4
compression is selected in addition. So instead of handling both cases
separately, check for LZ4 only if LZMA is not selected.
This applies to the cases of both, FSP-M and FSP-S.
Change-Id: I4ea61a38baf4c29bf522a50a26c6b47292e67960
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77323
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Fix the issue by adding the "ifeq" keyword which makes the extraneous
text a correct conditional directive.
Change-Id: Id8a8aa7acfdaeb0549f417fb013b2535a7298045
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77286
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
This patch uses the CSE firmware specific data to store Intel
ISH firmware related information. Sending an ISH partition version
information command on every boot cycle would impact the overall boot
performance.
This information is used by the auto-test framework to ensure the ISH
firmware update is proper for in-field devices.
BUG=b:285405031
TEST=Able to build and boot google/rex. Verified ISH FW version is
getting displayed across warm resets without impacting the boot time.
Change-Id: I0242c26dd90d834815799f54740d8147ff9d45b7
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch adds a new configuration option to allow the compression
algorithm for the logo cbfs file to be specified. By default, the logo
cbfs file is compressed using LZMA. However, enabling LZ4 compression
can save ~2ms of boot time when the BMP_LOGO config is enabled.
This patch verified that the logo cbfs file can be booted using either
LZMA or LZ4 compression.
BUG=b:284799726
TEST=Able to boot google/rex and verified firmware splash screen using
either LZMA or LZ4 compression.
Change-Id: Ib0aa5320632ae3f734004d2b1d495af11c2e1928
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Set the ACPI device status to hidden, since no driver is necessary or
available under Windows.
Linux is unaffected as it does not use the ACPI device status.
TEST=build/boot Win11 on google/akemi
Change-Id: Ib1e274084400fa47e483267d331e632ceb5be757
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75178
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds an API to convert BMP images into GOP BLT buffers for
Intel FSP-S. This is required to display the OEM splash screen at
pre-boot phase.
Previously, Intel FSP-S had provision to consume the *.BMP file as is.
However, starting with the Alder Lake platform, Intel FSP has dropped
this conversion logic and expects the boot firmware to pass the BLT
buffer directly.
This patch implements the conversion logic in coreboot.
BUG=b:284799726
TEST=Able to build and boot google/rex
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I992b45d65374f09498ff0cab497f7091e1e7a350
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
It makes no sense to expose these symbols to the user in the menu.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I6eb78d12afdc0828bf5e2d305f033d2f0cf4622a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
|
|
Width of registers are always dwords on pl011, not bytes.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I955319d31bba5c0cd4d50f2b34111d51fea653ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This is unused - other references were removed long ago.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ia7a65f54c736db20a5440795fdfaa8be31ef971f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
To help identify the licenses of the various files contained in the
coreboot source, we've added SPDX headers to the top of all of the
.c and .h files. This extends that practice to Makefiles.
Any file in the coreboot project without a specific license is bound
to the license of the overall coreboot project, GPL Version 2.
This patch adds the GPL V2 license identifier to the top of all
makefiles in the drivers directory that don't already have an SPDX
license line at the top.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I8442bc18ce228eca88a084660be84bcd1c5de928
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68980
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The prefix POSTCODE makes it clear that the macro is a post code.
Hence, replace related macros starting with POST to POSTCODE and
also replace every instance the macros are invoked with the new
name.
The files was changed by running the following bash script from the
top level directory.
header="src/soc/amd/common/block/include/amdblocks/post_codes.h \
src/include/cpu/intel/post_codes.h \
src/soc/intel/common/block/include/intelblocks/post_codes.h"
array=`grep -r "#define POST_" $header | \
tr '\t' ' ' | cut -d ":" -f 2 | cut -d " " -f 2`
for str in $array; do
splitstr=`echo $str | cut -d '_' -f2-`
grep -r $str src | cut -d ':' -f 1 | \
xargs sed -i'' -e "s/$str/POSTCODE_$splitstr/g"
done
Change-Id: Id2ca654126fc5b96e6b40d222bb636bbf39ab7ad
Signed-off-by: Yuchen He <yuchenhe126@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76044
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: I9241d713fb8cc26c768746c8e442b46292036d20
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76694
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use C99 flexible arrays instead of older style of one-element or
zero-length arrays.
It allows the compiler to generate errors when the flexible array does
not occur at the end in the structure.
Change-Id: Ideed4b333632df5068b88dde6f89d3831e3046d1
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
In the datasheet of ILI9882T [1] section 3.11 Power On/Off Sequence,
the TReset-CMD (Reset to First Command in Display Sleep In Mode) should
be larger than 10ms, but it's 1.1ms now. This may cause abnormal
display as some commands may be lost during power on. Fix this and
leave some margins by increasing TReset-CMD to 20ms. Also, to align
with the kernel driver structure starry_ili9882t_init_cmd, add 20ms
delay at the end of command.
[1] ILI9882T_Datasheet_20220428.pdf
BUG=b:293380212
TEST=Boot and display normally
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Ifdcaf0e34753fc906817c763f1c8e7389448d1dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76766
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Use C99 flexible arrays instead of older style of one-element or
zero-length arrays.
It allows the compiler to generate errors when the flexible array does
not occur at the end in the structure.
Change-Id: Iab55c57ee5cac60911c9fe4cee8d86a252bde372
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76839
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7c9c938bd20d36be8fdfb0d95bb58a7259650693
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Use C99 flexible arrays instead of older style of one-element or
zero-length arrays.
It allows the compiler to generate errors when the flexible array does
not occur at the end in the structure.
Change-Id: I03c21e180e9e399e5cb451bf3b9cfb6484cab68b
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76778
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use C99 flexible arrays instead of older style of one-element or
zero-length arrays.
It allows the compiler to generate errors when the flexible array does
not occur at the end in the structure.
Change-Id: I80b4b2df4a38dcbb28d928018446e91acae90ee6
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
There is a problem of screen shake on the old panel[1]. So increase the
panel GOP component pull-down circuit size in hardware, and update the
initialization code at the same time. The new initialization code is
mainly adjusted for GOP timing. When Display sleep in, raise all GOP
signals to VGHO and then drop to GND. In order to be consistent with
the current panel model, let's rename this file.
[1]: INX old panel product number is HJ110IZ-01A-B1, and the new
panel product number is HJ110IZ-01A-B2. We have recalled the shipment
old panel.
BUG=b:270276344
BRANCH=trogdor
TEST= test firmware display pass
Change-Id: I2b2534afee1ed700c39d3c360aafd685b63ccbfb
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Allows the new Infineon TPM chip used on Clevo laptops to be recognized.
Change-Id: I2ee31b787d80c0b9c24c748b1b28906a22a1dee7
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The OxPCIe952 serial cards currently fails after entering
postcar, since the state of oxpcie_present is not maintained
from previous stage.
As a quick work-around test the expected UART register space
to see if anyone decodes the address.
Change-Id: I5601034be6e413616fb3433c894fb008a3e02138
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74597
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
coreboot logs the error below, since the value of hporch is too small. Increasing hbl from 80 to 174, and hso from 40 to 72 to revise the HBP(Horizontal Back Porch) and HFP(Horizontal Front Porch). After revising this, the actual measurement frame rate is 60.1Hz.
[ERROR]HFP plus HBP is not greater than d_phy, the panel may not work
properly.
BUG=b:284812193
TEST=cbmem -c | grep "ERROR" and measure frame rate
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I7de5984ce8aec12d8ebe292974e05776835330d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76218
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I40b8482f41e8fece55fd60fec7ec3f63f83bd030
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76280
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Reserving resources needs to have inclusive region ends.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I88a09d205ef9699de7f18e0a2f33c9ad3ce9fa36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76279
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove BUILD_TIME_STAMP_SIZE macro from coreboot because FSP 3223
version have BUILD_TIME_STAMP_SIZE macro defined as part of
`FspProducerDataHeader.h`.
Ref change:
9c28ab1d1a vc/intel/fsp/mtl: Update header files from 3194_81 to 3223.80
BUG=b:285110116
TEST=Able to build google/rex.
Change-Id: I52707adf1aa6dadca8dcf82102f76916a0cfe346
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
tis_plat_irq_status() function is used only by Google TPM. It should
be moved to drivers/tpm/cr50.c. The name of the function was changed
to cr50_plat_irq_status().
BUG=b:277787305
TEST=Build all affected platforms
Change-Id: I78dc39f2c7b44232b06947d3dfe6afa52807ced8
Signed-off-by: Grzegorz Bernacki <bernacki@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75917
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Always send the Exit 4-Byte Address Mode (E9h) command before the first
access to the SPI flash in all stages when the SPI flash is
memory-mapped. This is useful for x86 mainboards that do not access SPI
flash in bootblock yet still need to exit 4-byte addressing mode in
romstage or ramstage.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I3a62bfa44a0a5645c1bb80b32d0b9f92075c66bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Commit d054bbd4f1ba ("Makefile.inc: fix multiple jobs build issue")
added a dependency on $(obj)/fmap_config.h to all .c source files in all
stages, so it's not needed any more to add it as a dependency to files
that include fmap_config.h.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7b62917f32ae9f51f079b243a606e5db07ca9099
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76002
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
The prefix POSTCODE makes it clear that the macro is a post code.
Hence, replace related macros starting with POST to POSTCODE and
also replace every instance the macros are invoked with the new
name.
The files was changed by running the following bash script from the
top level directory.
sed -i'' '30,${s/#define POST/#define POSTCODE/g;}' \
src/commonlib/include/commonlib/console/post_codes.h;
myArray=`grep -e "^#define POSTCODE_" \
src/commonlib/include/commonlib/console/post_codes.h | \
grep -v "POST_CODES_H" | tr '\t' ' ' | cut -d ' ' -f 2`;
for str in ${myArray[@]}; do
splitstr=`echo $str | cut -d '_' -f2-`
grep -r POST_$splitstr src | \
cut -d ':' -f 1 | xargs sed -i'' -e "s/POST_$splitstr/$str/g";
grep -r "POST_$splitstr" util/cbfstool | \
cut -d ':' -f 1 | xargs sed -i'' -e "s/POST_$splitstr/$str/g";
done
Change-Id: I25db79fa15f032c08678f66d86c10c928b7de9b8
Signed-off-by: lilacious <yuchenhe126@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch introduces CBMEM ID to store the MRC version (similar to
existing implementation that stores the FSP-M version inside CBMEM ID)
inside cbmem so the version information is available across the
different coreboot stages. For example:
* romstage: Use the CBMEM ID version information to check if the MRC
cache is valid and need to erase the MRC cache
* ramstage: Use the CBMEM ID to store the MRC cache into the
non-volatile space.
BUG=b:261689642
TEST=Able to build and boot google/rex and dump the MRC version as
below.
cbmem --list
CBMEM table of contents:
NAME ID START LENGTH
...
21. MRC VERSION 5f43524d 75ffeb60 00000004
...
localhost ~ # cbmem -r 5f43524d | hexdump
00000000 01 12 07 00
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I91f735239b33c6f8ba41c076048903e4b213c6a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75921
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch uses the "generic" variable name as "version" while storing
the MRC cache data instead referring to the FSP-M version or MRC
version. Hence, updated all the instances of `fsp_version/fspm_version`
with `version`.
Also introduces the new option to the MRC cache
version that allows SoC users to store the MRC cache version based on
the supported EDK2 version. Intel FSP built with EDK2 version 202302
onwards has support to retrieve the MRC version by directly parsing
the binary.
Additionally, added the helper function `fsp_mrc_version()` and
corresponding header file to read the MRC version from the FSP binary.
BUG=b:261689642
TEST=Able to build and boot google/rex and google/omnigul.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ia8af53aed674ad4a3b426264706264df91d9c6b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75920
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
FSP performance timestamp is in nano second by default. This patch is to
correct unit in FSP performance timestamp data print and macro name to
avoid confusion.
Change-Id: I4aec4f63beddbd7ce6e8e3fc1b53a45da2ee0b00
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75816
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
In commit e59f18bf29a8 ("drivers/i2c: Add PI7C9X2G608GP PCIe switch
driver (pi608gp)"), there were some suggestions after it's been already
merged.
This patch addresses the points regarding the code style and comments.
BUG=none
TEST=Build OK, no behavioral changes in the pi608gp driver, console logs
without changes.
Change-Id: I5fc54708e0085fea4bd1f2fbf2afb400d2ccbd46
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
In commit e59f18bf29a8 ("drivers/i2c: Add PI7C9X2G608GP PCIe switch
driver (pi608gp)"), there were some suggestions after it's been already
merged.
This patch addresses the points regarding the number types - fix of the
printk format strings, inclusion of 'stdint.h' and marking the set of
allowed values as constant.
BUG=none
TEST=Build OK, no behavioral changes in the pi608gp driver, console logs
without changes.
Change-Id: I34c664f6a8a257b260facdbf9043825ff4a4c932
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75500
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This patch renames `SOC_INTEL_STORE_CSE_FPT_PARTITION_VERSION` config
to `SOC_INTEL_STORE_ISH_FW_VERSION` to ensure the usage of this config
is clear.
Any platform would like to fetch the currently running ISH firmware
version should select this configuration.
TEST=Able to build and boot google/marasov.
Change-Id: Ie503d6a5bf5bd0d3d561355b592e75b22c910bf5
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75767
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This fixes format string vulnerability issues with snprintf statement
found by klocwork scan.
Foundby=klocwork
BUG=NONE
TEST=Boot to OS on Meteor Lake rex platform and run klocwork scan.
Check related ACPI tables and modem driver behavior after changes.
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Change-Id: Ia6b7d70c0b2b86d0918e58348dccd206a7ee9193
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75733
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of adding the new PCI IDs of the XHCI controllers in every new
chip generation to the pci_xhci driver, bind the driver to the internal
PCI devices of the XHCI controllers via the device ops statement in the
chipset devicetree. The PCI device function of the XHCI2 controller in
Mendocino can be either a dummy device or the XHCI controller, so the
device ops are attached to that device in the mainboard devicetree
instead. The Glinda code is right now just a copy of the Mendocino code,
so it'll change in the future, but for consistency the equivalent
changes to those in Mendocino are applied there too.
Since the device ops are now attached to the devices via the static
devicetree entry, also remove both the xhci_pci_driver struct and the
amd_pci_device_ids array from drivers/usb/pci_xhci/pci_xhci.c.
TEST=SSDT entries for the XHCI controllers are still generated on
Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9c455002c6d2aac576fe24eee0c31744b4507bb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Hook up xhci ops for Phoenix xHCI device. Benefit is we don't have to
bother by adding xhci DID.
BUG=b:285981912
TEST=check coreboot log shows below.
[INFO ] \_SB.PCI0.GP41.XHC0.RHUB.SS01: USB3 Type-A Port A0 (MLB)
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ib59874948725966b04b54def3f6de463afeda709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
BUG=b:285110121
TEST=boot Myst and verify the flash is recognized
Change-Id: I30aed5299f87f7cf02fe9a5569edd2b8dcf7b452
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Print the flash ID codes when find_match fails to match the flash.
BUG=b:285110121
Change-Id: I2106abfcfbd44c7d56d48ffbb43d8c76089af076
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Add a new Kconfig LINUXPAYLOAD_CMDLINE_VPD_OVERWRITE that can overwrite
Linux payload's kernel command line from VPD. Currently only overwrite
Linux kernel command line 'loglevel' via VPD key 'kernel_log_level'.
TESTED=On OCP Delta Lake, with kernel_log_level set to 0, warm reboot
time can see about 10 seconds improvement comparing to kernel log level
7.
Change-Id: Idf06c7ab9958c940fc3b23d560bb9dade991a6da
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ib8ee07aefdb32b8efe719f484e242b6129596842
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
"extern" is automatically implied with function declaration.
Change-Id: Ic40218acab5a009621b6882faacfcac800aaf0b9
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71890
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The CS42L42 low power audio codec can be connected over SoundWire and
be configured for mainboards to use:
- Data Port 0 and Bulk Register Access
- Data Port 1 is the 64bit data output for the headset
- Data Port 2 is the 64bit data input for the headset
- Data Port 3 is the 64bit data input for the headset
The data port and audio mode properties are filled out as best as
possible with the datasheet as a reference.
The ACPI address for the codec is calculated with the information in
the codec driver combined with the devicetree.cb hierarchy where the
link and unique IDs are extracted from the device path.
For example this device is connected to master link ID 0 and has strap
settings configuring it for unique ID 0.
chip drivers/soundwire/cs42l42
register "desc" = ""Headset Codec""
device generic 0.0 on end
end
This driver was tested with the rex0 reference design by booting
and disassembling the runtime SSDT to ensure that the devices have the
expected address and properties.
Device (SW00)
{
Name (_ADR, 0x00001001FA424200) // _ADR: Address
Name (_DDN, "Headset Codec") // _DDN: DOS Device Name
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
GpioInt (Edge, ActiveBoth, Exclusive, PullDefault, 0x0000,
"\\_SB.PCI0.GPIO", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0166
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.PCI0.GPIO", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0167
}
})
Name (_DSD, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "irq-gpios",
Package () { \_SB.PCI0.HDAS.SNDW.SW00, Zero, Zero, Zero }
},
Package () { "reset-gpios",
Package () { \_SB.PCI0.HDAS.SNDW.SW00, One, Zero, Zero }
},
Package () { "cirrus,ts-inv", One },
Package () { "cirrus,ts-dbnc-rise", 0x05 },
Package () { "cirrus,ts-dbnc-fall", Zero },
Package () { "cirrus,btn-det-init-dbnce", 0x64 },
Package () { "cirrus,btn-det-event-dbnce", 0x0A },
Package () { "cirrus,bias-lvls",
Package () { 0x0F, 0x08, 0x04, One }
},
Package () { "cirrus,hs-bias-ramp-rate", 0x02 },
Package () { "cirrus,hs-bias-sense-disable", One },
Package () { "mipi-sdw-sw-interface-revision", 0x00010000 },
[...]
Package () { "mipi-sdw-source-port-list", 0x02 },
Package () { "mipi-sdw-sink-port-list", 0x0C }
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package ()
{
Package () { "mipi-sdw-port-bra-mode-0", "BRA0" },
Package () { "mipi-sdw-dp-0-subproperties", "DP0" },
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" },
Package () { "mipi-sdw-dp-1-source-subproperties", "SRC1" },
Package () { "mipi-sdw-dp-2-sink-subproperties", "SNK2" },
Package () { "mipi-sdw-dp-3-sink-subproperties", "SNK3"}
}
})
Name (BRA0, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mipi-sdw-bra-mode-bus-frequency-configs",
Package () { 0x00AC4400, ... }
},
Package () { "mipi-sdw-bra-mode-max-data-per-frame", 0x1000 },
Package () { "mipi-sdw-bra-mode-min-us-between-transactions", Zero }
}
})
Name (DP0, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mipi-sdw-port-max-wordlength", 0x40 },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package ()
{
Package () { "mipi-sdw-port-bra-mode-0", "BRA0" }
}
})
Name (MOD0, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mipi-sdw-audio-mode-bus-frequency-configs",
Package () { 0x00AC4400, ... }
},
Package () { "mipi-sdw-audio-mode-max-sampling-frequency", 0x0002EE00 },
Package () { "mipi-sdw-audio-mode-min-sampling-frequency", 0x1F40 },
[...]
}
})
Name (SRC1, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mipi-sdw-data-port-type", Zero },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package ()
{
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" }
}
})
Name (SNK2, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mipi-sdw-data-port-type", Zero },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package ()
{
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" }
}
})
Name (SNK3, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mipi-sdw-data-port-type", Zero },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package ()
{
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" }
}
})
}
BUG=b:269497731
TEST=Verified SSDT for SNDW in the OS
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ic7cfe2a21c76ba01ad3dea2a5017b28743aeb9f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73279
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The MAX98363 smart speaker amp can be connected over SoundWire and be
configured for mainboards to use:
- Data Port 0 and Bulk Register Access is not supported
- Data Port 1 is the 32bit data input for the speaker path
The data port and audio mode properties are filled out as best as
possible with the datasheet as a reference.
The ACPI address for the codec is calculated with the information in
the codec driver combined with the devicetree.cb hierarchy where the
link and unique IDs are extracted from the device path.
For example this device is connected to master link ID 2 and has strap
settings configuring it for unique ID 0.
chip drivers/soundwire/max98363
register "desc" = ""Left Speaker Amp""
device generic 2.0 on end
end
This driver was tested with the rex0 reference design by booting
and disassembling the runtime SSDT to ensure that the devices have the
expected address and properties.
Device (SW20)
{
Name (_ADR, 0x000230019F836300) // _ADR: Address
Name (_DDN, "Left Speaker Amp") // _DDN: DOS Device Name
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_DSD, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mipi-sdw-sw-interface-revision", 0x00010000 },
[...]
Package () { "mipi-sdw-source-port-list", Zero },
Package () { "mipi-sdw-sink-port-list", 0x02 }
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package ()
{
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" },
Package () { "mipi-sdw-dp-1-sink-subproperties", "SNK1" }
}
})
Name (MOD0, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mipi-sdw-audio-mode-bus-frequency-configs",
Package () { 0x00927C00, ... }
},
Package () { "mipi-sdw-audio-mode-sampling-frequency-configs",
Package () { 0x3E80, ... }
},
[...]
}
})
Name (SNK1, Package ()
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mipi-sdw-data-port-type", Zero },
[...]
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package ()
{
Package () { "mipi-sdw-port-audio-mode-0", "MOD0" }
}
})
}
BUG=b:269497731
TEST=Verified SSDT for SNDW in the OS
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ie56109d615759e3e5e32782c8782cb2f47014ec4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73278
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If Fastboot is enabled, the next boot will skip MRC and won't be able
to detect MRC error via EWL and still continues booting. Enforce FSP
MRC training in the next boot.
Change-Id: I9dee0472f8e2602cecf88c6d00dec0bf02b9f7bd
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Add sending Meta's BMC SEL for memory training error occurred in EWL
type 3 error.
The detail definition of EWL (Enhanced Warning Log) can be found in the
specification document -- BIOS Data ACPI Table (BDAT) Interface
Specification v4.0 Draft 5:
https://uefi.org/sites/default/files/resources/BDAT%20Specification%20v4.0%20Draft5_0.pdf
Change-Id: I664e9d3da7910b47260881c0df64159c8dbe2dca
Signed-off-by: Shelly Chang <Shelly_Chang@wiwynn.com>
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69147
Reviewed-by: Jonathan Zhang <jon.zhixiong.zhang@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Bochs graphics adapter remaps the legacy VGA ioports
(0x3c0 -> 0x3df) to its MMIO region at offsets 0400 - 041f.
Currently bochs_vga_write() calculates a wrong offset when
accessing these ioports, which causes the boot splash image
not displayed when using the legacy-free pci variant of the
Bochs graphics adapter.
TEST=Build coreboot for QEMU x86 i440fx with a boot splash image
included, boot coreboot.rom with QEMU with '-device secondary-vga'
and verify the boot splash image is correctly displayed.
Fixes: efaf1b32ba1e ("drivers/emulation/qemu/bochs: Rewrite driver")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Change-Id: I4acc71e3d6ef5161ab62e6714c94b7643c4c0972
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75146
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Some devices using the MAX98373a smart amp have the speakers connected
to port SSP2 vs the default SSP1, so add a configuration item to be
able to specify that.
TEST=tested with rest of patch train
Change-Id: I11d8011c54946aa72a83c73fa88456b4bb5d7d95
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75231
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also correct switch intendation, remove excess empty lines.
Change-Id: I86026e7f6c0c1c7f3dc6a473bb3afe2f6d32a247
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75230
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Will allow boards using this speaker configuration to correctly specify
their output type.
TEST=tested with rest of patch train
Change-Id: Iefcfc928e2611f533af1a2962ec2761ec1b7bf3a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add _STA field entry for r8168 ACPI device and set to
ACPI_STATUS_DEVICE_HIDDEN_ON in order to hide device from
OS (Windows) as there is no driver needed (or available).
Windows correctly attaches drivers to the PCIe device, the
separate ACPI device is unused and unneeded.
Linux is unaffected as it does not use the ACPI device status.
Change-Id: Ib7ae99fffcb00e71421b93c2794119841aa239d3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75177
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Restore the reverted 'commit 059902882ce5 ("drivers/ocp/ewl: Add EWL
driver for EWL type 3 error handling")'.
2. Print more EWL type 3 error information when it occurs.
Change-Id: Ib83b7653a839d18a065b929127549acd10bce7a7
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jon.zhixiong.zhang@gmail.com>
|
|
Adds the option to set the 'DmaProperty' in the device's _DSD.
This can be done by setting "add_acpi_dma_property"="true". If not set
(or set to false), the device descriptor generation behavior will remain
unchanged. The naming convention for the config option was chosen to
match that of other drivers.
This partially reverts commit 5609f7a684c6 ("drivers/pcie/generic: Clean
up driver") as the driver is now used on a couple mainboards which need
the DmaProperty.
Change-Id: I996fe4923948d13a20bf8b6b1a93dab0866d0fd4
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add STA_ILI9882T panel serializable data to CBFS.
The panel datasheet: ILI9882T_Datasheet_20220428.pdf
BUG=b:275470328
BRANCH=corsola
TEST=build and check the CBFS include the panel
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Ia7a37c0659f0959fe7be01aba0f08d63119d139f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
|
|
Configure the CMOS bank I/O base addresses with
PC_CMOS_BASE_PORT_BANK* rather than hard-coding as 0x70, 0x72. The
defaults remain the same.
Change-Id: Ie44e5f5191c66f44e2df8ea0ff58a860be88bfcf
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74903
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CMOS defaults greater than 128 bytes long will extend to bank 1.
Change-Id: I9ee8364d01dd8520be101de3f83d2302d50c7283
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add STA_HIMAX83102_J02 panel serializable data to CBFS.
The panel datasheet: HX83102-J02_Datasheet_v03.pdf.
BUG=b:272425116
BRANCH=corsola
TEST=build and check the CBFS include the panel
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I382bdc89e5a217fd1c28e677938f454dc09725cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Add _PLD support to GFX device so that each display output can store
its physical location of connection point. This is to be used primarily
for describing DP on USB-C ports in the future patches.
The upstream Linux kernel now has a feature to compare _PLD of Type C
connectors and DP connectors to link them together.
https://cgit.freedesktop.org/drm/drm-misc/commit/?id=c5c51b2420625faa1f0e363f21dba1de53806ff7
This feature allows us to tell which display output is used by which
USB-C port.
So, for the future boards, we want to add _PLD for each DP connector
matching with the corresponding USB-C port.
BUG=b:277629750
TEST=emerge-${BOARD} coreboot
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: I393207746a9e82c1fd7622ab3661d7b1232cb62f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch adds some of the variety of configuration options exported
by the Pericom Inc. PI7C9X2G608GP PCIe switch over its SMBus interface.
Currently implemented options are only used to adjust the switch
upstream port amplitude and de-emphasis levels in millivolts. Only
values specified in the switch datasheet (in tables 6-6 and 6-8) are
allowed.
Example of a devicetree.cb entry:
chip drivers/i2c/pi608gp
register "gen2_3p5_enable" = "true"
register "gen2_3p5_amp" = "AMP_LVL_MV(425)"
register "gen2_3p5_deemph" = \
"DEEMPH_LVL_MV(37, 5)"
device i2c 0x6f on
ops pi608gp_ops
end
end
Link to the datasheet:
https://web.archive.org/web/20210225074853/https://www.diodes.com/assets/Datasheets/PI7C9X2G608GP.pdf
BUG=none
TEST=Create devicetree.cb and Kconfig entries for this driver
in a mainboard containing the switch and verify, that the values read
out from the switch config space match the values programmed over the
SMBus.
Change-Id: Id191c4e97b99da58efd3ba38bf8cca3603ece4d5
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
DSM (Dynamic Speaker Management) uses calibration parameters stored in
a VPD (Vital Product Data) FMAP region to configure the audio output
via an ACPI _DSD table. This has no dependency on a ChromeOS, and can
be used by Linux/Windows drivers if appropriately configured.
Remove the dependency of DSM_CALIB (and the calibration file) on
CHROMEOS and replace it with VPD, so that non-CHROMEOS builds
can utilize this feature as well. Move files from underneath
vc/google/chromeos to underscore the point.
TEST=build/boot google/nightfury, dump ACPI, verify DSM calibraton
parameters present in _DSD table.
Change-Id: I643b3581bcc662befc9e30736dae806f94b055af
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
