| Age | Commit message (Collapse) | Author |
|---|
|
This option is neither selected nor usable for the only remaining SoC
that uses this code, so drop the remaining parts. configure_hudson_uart
isn't called anywhere and isn't even compiled, since it's guarded by an
#if CONFIG(HUDSON_UART) block and the HUDSON_UART Kconfig option isn't
selected anywhere. Both the offsets used in the iomux_write8 calls and
the UART controller itself aren't listed in the BKDG #52740 Rev 3.05 for
the AMD Family 16h Models 30h-3Fh APUs which is the only SoC that uses
this code, so the code didn't even apply for this chip.
TEST=Timeless build for pcengines/apu2 results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3f462d1f83a0f1ba851329ebebb1f3263267fdc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This config selected ADD_FSP_BINARIES even though HAVE_INTEL_FSP_REPO is
only defined for Apollolake and not Geminilake that resides in the same
SoC directory and uses the same Kconfig file. This results in the paths
to the FSP binaries not being defined, in which case the
ADD_FSP_BINARIES option shouldn't be selected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I95123c4930b44a3b76c87768e130eb7359bbf625
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since the FSP binaries for Picasso are present in the amd_blobs repo,
select the ADD_FSP_BINARIES option if the Kconfig option to check out
that repo is set.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9a8571730cf271ad5e113e5df87700882b3c5475
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch ensures mp_run_on_all_aps() is passing 'MP_RUN_ON_ALL_CPUS'
macro rather hardcoding `0` while running `func` on all APs.
Change-Id: Icd34371c0d4349e1eefe945958eda957c4794707
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
EGPIO132 is the last documented GPIO on the GPIO controller in the NDA
version of the BKDG for AMD Family 16h Models 30h-3Fh Processors (#52740
Rev 3.06) which is the only SoC using this code, so define
SOC_GPIO_TOTAL_PINS as 133, since the internal GPIO numbers are
0-indexed. This definition will be needed the subsequent patch that'll
add the remote GPIO support to the common AMD GPIO code to make sure
that the compiler can optimize out the code path needed to support the
remote GPIO access which isn't available on this platform anyway.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I877d462c5e753c9bbb3461dbb10cde2adc2cb12c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
If a USB_MUX_EVENT happens while the AP is in S3 during powerdown
transtion (S0->S3->S5), this will cause the device to boot again after
it has finished sequencing down to S5. Since S3 is not POR for ChromeOS
devices anymore, change this event to wake from S3 and S0ix to just
S0ix.
BUG=b:197039097
TEST=abuild
Change-Id: I91e5e0ab8301377817875b6fa9e3c0e1f96c1465
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add NixOS configurations for bootable live systems containing a set of
tools which might be useful for firmware development in general and for
working on coreboot.
There are two configurations provided. One for console-only and a
graphical one, which is mostly the same as the console image but it
comes with Gnome Shell as window manager and some graphical tools in
addition.
An image can be built using `build-console.sh`, respectively
`build-graphical.sh`. The resulting iso image can be found in
`result/iso/`.
The console image results in ~700MB, while the graphical one results in
~2GB.
Change-Id: Iaf49d198e99781434bd89d2a8a125a4988b77e1c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
This patch updates debug message to specifically the case when SMBIOS
table 7 write would abort due to either `unknown` CPU or CPU `doesn't
have support for deterministic cache cpuid leaf`.
Change-Id: I288593b3f78ab858bf66c689e7cfb6ba2ff746d0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Don't attempt to fill the SMBIOS table if the CPU doesn't support
deterministic cache CPUID.
TEST=Able to fix the hang issue seen on ASRock E350M1 with commit hash
e2b5fee.
Change-Id: Id65dc963e235f7080370a32cf69bcc4bee94d28f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57306
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`cpu_get_cache_info_leaf()` function is responsible to report leaf
value for CPU that have support for deterministic cache cpuid. As per
available datasheets from AMD and Intel the supported CPUID leafs are
0x8000_001d for AMD and 0x04 for Intel. Hence, this CL skips returning
default leaf value as `0`.
TEST=Verified fixes: e2b5fee3b006 (arch/x86: smbios write 7 table using
deterministic cache functions) hang issue on ASRock E350M1.
Change-Id: Iee33b39298e7821ac5280d998172b58a70c8715b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57305
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor Qcom QSPI driver to separate common
and SoC specific driver code.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: Ibe1dc3fe8bd71957ff8604ef4c9d97963100ccfb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
There are two different types of 682 SKU available with TDP
of 28W and 45W. This patch fix override values for power
limits for these 682 SKU. This patch also sets power limit
values dynamically based on machine ID and CPU TDP of SKU.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I796e56321ae9c8312530a4b8986cd73a2245f5fa
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57290
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
copy existing QSPI driver from /soc/qualcomm/sc7180 to common folder.
This common QSPI driver works in master mode and provides read/write
operation for the slave devices like flash.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I5b3816b823e14db1dd13f1eb4a6761c7a61604b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Introduce DDR One-Time-Training Support
Device reboots without training from second iteration
and also DDR training data is 32kb size, hence update
required in memlayout and to sync with upstream changes
the Fmap size even got bumped up.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: I81038c5c7802c154f4310509c6c64710580b8ce4
Signed-off-by: Sudheer Kumar Amrabadi <samrabad@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Configure 384MHz for eMMC clock and 50MHz for SD card clock.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: I8acbce58614add0228adc39289762da10937cbe2
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
It supports the clock consumers for QUP, SDCC, PCIE, Display to be able
to configure & enable the desired clocks.
The clock driver also supports reset of subsystems like AOP and SHRM.
Also add support for Zonda PLL enable for CPU in common clock driver.
Refactor the SC7280 clock driver to use the common clock driver APIs.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: I590a93cda0d6eccb51b54692b620d43ccacede77
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50580
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add TPM IRQ config to gpio_m.c, so the TPM IRQ is not allocated
to I2C4.
BUG=NA
BRANCH=None
TEST= boot to os and check cat /proc/interrupts, cr50 SPI interrupt is assigned
and does not conflict with I2C.
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 CPU8 CPU9 CPU10 CPU11
0: 36 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 2-edge timer
1: 0 0 0 0 0 0 0 0 9 0 0 0 IO-APIC 1-edge i8042
8: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 8-edge rtc0
9: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 9-fasteoi acpi
14: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 14-fasteoi INTC1055:00
16: 0 0 0 0 0 0 0 0 0 0 4 0 IO-APIC 16-fasteoi intel-ipu6
22: 0 13 0 0 0 0 0 0 0 0 0 0 IO-APIC 22-fasteoi idma64.4, i801_smbus, ttyS0
37: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 37-fasteoi idma64.0, i2c_designware.0
38: 0 0 0 0 0 0 0 0 0 0 4 0 IO-APIC 38-fasteoi idma64.1, i2c_designware.1
41: 0 0 0 0 2274 0 0 0 0 0 0 0 IO-APIC 41-edge cr50_spi
42: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 42-fasteoi idma64.2, i2c_designware.2
43: 4 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 43-fasteoi idma64.3, i2c_designware.3
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Change-Id: Id0f3885dec5a6f635254c233709090321491c739
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57102
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set power limit values dynamically based on CPU TDP and PCI ID of SKU.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: Ic331a3debb076ef08a312a31edc1468974fd4902
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57035
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get tdp value of CPU for different SKUs based on PKG POWER MSR.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I9fba0a64da2f1d79d633054dddd9fdf1d3d8e258
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Add GPIO IOMUX defines for the pins that are used in the mainboard code
which enables using the PAD_GPI and PAD_GPO macros.
TEST=Timeless build for APU2/3/4/5 results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie32df9ed2cb6a5670a29cff91e085a3585c8bcf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
southbridge/amd/pi/hudson uses the common GPIO bank access code from
soc/amd, but doesn't provide all functionality that would be needed to
use the full functionality. Add a Kconfig option that switches off some
functionality in the common SoC GPIO access code, so that more of the
functionality proviced by the common SoC GPIO code can be used in the
AMD binaryPI chipset and board code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib10d5d5580aab30a359aa001bb6fc7e9fdb8fc41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56783
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The mapping of the package GPIO numbers to the GPIO numbers on the GPIO
controller isn't a 1:1 one, so add a comment about that to avoid
confusion. Also change the comment style to match the style guide.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie30bf5483ea2e2516d7e3fdd21ea9338362e526e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Also remove the unused amdblocks/acpimmio.h include in gpio_ftns.c.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Michał Kopeć <michal.kopec@3mdeb.com>
Change-Id: If121941c8a6ba88913653192740997aeef426548
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56784
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Override DdiPortAConfig as MIPI DSI
BUG=b:192521391
BRANCH=None
TEST=Built test coreboot image and boot on bugzzy board
Change-Id: If308f9d69fea56176527e7b67f36b29c43adb525
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Make adding the FSP-T file to CBFS depend on both ADD_FSP_BINARIES and
FSP_CAR Kconfig options being set. The FSP_T_FILE Kconfig option depends
on both, so also check if both are selected in the Makefile where it
tries to add the FSP-T to the CBFS.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Furquan Shaikh <furquan@google.com>
Change-Id: Id347336f2751c6d871f31d89c30a1222037c2d69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Remove unused drivers and some fast calibration implementations
to align with the latest MTK memory reference code.
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: I3b235cbceb231898f00fce7905f596eab54ca595
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57275
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The clock driver supports configuring the general purpose PLLs,
configuring the root clock generator (RCG), enable clock branch, enable
gdsc and also the block resets.
The common clock driver exposes PLL configuration functions and also
different Agera PLL enable functions for the CPU PLLs.
While at it, the common driver also supports reset of subsystems like
AOP and SHRM.
SC7180 clock driver is also refactored to use the common clock
driver APIs.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Change-Id: I03d1b4a2fb90303c7259ec08f312d78b4e33ec39
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
As we move to use the common clock driver, the sc7180 clock driver,
watchdog and display drivers requires few cleanups, thus update the
impacted drivers.
Earlier the display client is expected to provide 2n divider value,
as the divider value in register is in form "2n-1".
mdss_clk_cfg.div = half_divider ? (half_divider - 1) : 0;
The older convention in the upcoming patches would be replaced with
the common macro of QCOM_CLOCK_DIV, thus need the divider needs to
be updated.
mdss_clk_cfg.div = half_divider ? QCOM_CLOCK_DIV(half_divider) : 0;
To accommodate impacting the functionality, the half_divider is taken
care in the clock driver.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 development board
Change-Id: Ic334fd0d43e5b4b1e43a27d5db7665f0bc151d66
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
CONFIG_DRIVERS_INTEL_MIPI_CAMERA and CONFIG_SOC_INTEL_COMMON_BLOCK_IPU
are getting selected for all ADLRVPs irrespective of ADL-P and ADL-M
(internal and external EC SKUs) hence, select those Kconfigs from
mainboard Kconfig rather Kconfig.name.
Also, select DRIVERS_INTEL_SOUNDWIRE as per alphabetical order.
TEST=No changes are seen while the .config file is getting auto
generated.
Change-Id: I62d5ec19c3364da79ebe7287b1b3d6eb2a0efca0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Set the `UserBd` FSP-M UPD to `BOARD_TYPE_DESKTOP` by default on PCH-H.
Remove now-redundant mainboard code to set the `UserBd` UPD.
Change-Id: I349abe5d89f562c158ce9baadbca2b2f56695846
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57261
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SoC code already sets this UPD to `CONFIG_IED_REGION_SIZE`, which
defaults to 0x400000 for soc/intel/cannonlake.
Change-Id: I6587e17a4a3425c561cffe6e3df0d932a2458168
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Change-Id: I291dc71bb6e3888b71ebce315f9ad09ccbc4a9a7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Specify the type of the `DIMM_MAX` Kconfig symbol once.
Change-Id: I2e86baaa8bd50c7b82c399fde5dcea05da6b4307
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Specify the type of the `DIMM_SPD_SIZE` Kconfig symbol once.
Change-Id: I619833dbce6d2dbe414ed9b37f43196b4b52730e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
variant_has_pcie_wwan() was always coming back as disabled because
find_dev_nested_path() couldn't find the device until the domain was
added to the array.
BUG=b:193036827
TEST=Boot guybrush with PCIe & USB WWAN devices.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Id94fa0b0ff5c29fa447e869220d27ccfe61438c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: I0b1c29162a64030b5c100368f2471702e22b8311
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The RW_MRC_CACHE only needs to be 64K for Brya.
BUG=none
TEST="emerge-brya coreboot chromeos-bootimage", flash and boot
brya0 to kernel.
Change-Id: I74365b795e184b92f483ae2bf862791e235c5362
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56989
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for DSM methods as per the connectivity document
559910_Intel_Connectivity_Platforms_BIOS_Guidelines_Rev6_4.pdf
BUG=b:191720858
TEST=Check the generated SSDT tables for DSM methods
Change-Id: Ie154edf188531fe6c260274edaa694cf3b3605d3
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add support for the WTAS ACPI BIOS configuration table as per the
connectivity document:
559910_Intel_Connectivity_Platforms_BIOS_Guidelines_Rev6_4.pdf
BUG=b:193665559
TEST=Generated SAR file with the WTAS related configuration values and
verified that the SSDT has the WTAS ACPI table.
Change-Id: I42cf3cba7974e6db0e05de30846ef103a15fd584
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add support for the PPAG ACPI BIOS configuration table as per the
connectivity document:
559910_Intel_Connectivity_Platforms_BIOS_Guidelines_Rev6_4.pdf
BUG=b:193665559
TEST=Generated SAR file with the PPAG related configuration values and
verified that the SSDT has the PPAG ACPI table.
Change-Id: Ie8d25113feeeb4a4242cfd7d72a5091d2d5fb389
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Existing SAR infrastructure supports only revision 0 of the SAR tables.
This patch modifies it to extend support for intel wifi 6 and wifi 6e
configurations as per the connectivity document:
559910_Intel_Connectivity_Platforms_BIOS_Guidelines_Rev6_4.pdf
The SAR table and WGDS configuration block sizes were static in the
legacy SAR file format. Following is the format of the new binary file.
+------------------------------------------------------------+
| Field | Size | Description |
+------------------------------------------------------------+
| Marker | 4 bytes | "$SAR" |
+------------------------------------------------------------+
| Version | 1 byte | Current version = 1 |
+------------------------------------------------------------+
| SAR table | 2 bytes | Offset of SAR table from start of |
| offset | | the header |
+------------------------------------------------------------+
| WGDS | 2 bytes | Offset of WGDS table from start of |
| offset | | the header |
+------------------------------------------------------------+
| Data | n bytes | Data for the different tables |
+------------------------------------------------------------+
This change supports both the legacy and the new format of SAR file
BUG=b:193665559
TEST=Checked the SSDT entries for WRDS, EWRD and WGDS with different
binaries generated by setting different versions in the config.star
Change-Id: I08c3f321938eba04e8bcff4d87cb215422715bb2
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
GPIO PM was disabled for brya to evaluate if longer interrupt pulses
are required for ADL. Since ADL requires 4us long pulses (EDS:626817),
GPIO PM can be enabled. All devices currently tested on brya support 4us
long pulses. This change drops the GPIO PM override and re-enables
dynamic GPIO PM.
TEST=Boot brya to OS, ensure no TPM errors.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0c7b66b5514d8b80775ab7578ce7b12181af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56926
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It doesn't make sense to store the orientation field directly in the
panel information structure, which is supposed to be reuseable between
different boards. The thing that determines orientation is how that
panel is built into the board in question, which only the board itself
can know. The same portrait panel could be rotated left to be used as
landscape in one board and rotated right to be used as landscape in
another. This patch moves the orientation field out of the panel
structure back into the mainboards to reflect this.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If2b716aa4dae036515730c12961fdd8a9ac34753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57324
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable PCIE port 7 using clk 6 for RTL8125 Ethernet
BUG=b:193750191
BRANCH=None
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ic60a66dbd6ad87cf9c0de85ca7df4d854c371bf5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
TGL-H supports up to 8 cores (16 threads).
Change-Id: I2ee1be37f564bf1b6249a6c223be093747c38ab5
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Windows will write to the century byte (0x32), causing the option table
checksum to be invalid and reset all options to their default values.
Move options and checksum to start after the century byte.
Change-Id: Ia395acacda1e251251c880587bbf61d7ee81ba3d
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNCPMMLXR-NEE
K4UBE3D4AA-MGCR
BUG=b:194031783
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I71ceaf0a2738584d316a5b7cc51539821b430128
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
It turns out that putting a device ref in an overridetree at a different
point in the tree will generate a duplicate device definition, such that
the change introducing this support was ignoring the device presence
specified by overridetree.cb and only using the baseboard configuration.
I believe testing of that change was not redone after the baseboard was
changed to disable the MST, so that conflicting behavior was not
noticed.
The incorrect behavior generated a disabled device for the MST at the
location specified by the baseboard, and one with the probe as a child
of the soc. At runtime this did a fw_config probe of the "I2C 00:4a"
device, and later probed a different "I2C 00:4a" which was already
disabled. As the disabled one came later, it seems to have completely
disabled the MST, discarding the results of the variant-specific probe.
BUG=b:185862297
TEST=10EC2141 device is now present on a Dali berknip
BRANCH=zork
Change-Id: I2a8feb544f3fc198fe6313b226ad8995aad31c3e
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57298
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The patch is to fix "Not a usable UEFI firmware volume" issue when
creating CBFS/flash image. This issue is caused by adding FvNameGuid
in UefiPayloadEntry.fdf in EDKII. There is an ext header between header
of Fv and header of PayloadEntry in Fv with FvNameGuid. The ext header
causes the UefiPayloadEntry to be found incorrectly when parsing Fv.
Commit in EDKII: 4bac086e8e007c7143e33f87bb96238326d1d6ba
Bugzila: https://bugzilla.tianocore.org/show_bug.cgi?id=3585
Signed-off-by: Dun Tan <dun.tan@intel.com>
Change-Id: Id063efb1c8e6c7a96ec2182e87b71c7e8b7b6423
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57296
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: King Sumo <kingsumos@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit adds test case for lib/cbfs verification mechanisms.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I1d8cbb1c2d0a9db3236de065428b70a9c2a66330
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56601
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The new CBFS stack was written to try to isolate cases of single file
corruption as far as possible and still make other files avaialble (at
least as long as verification is disabled and they can still be found at
all). For most cases of header corruption, it will just continue trying
to parse the next file. However, in cases where parts of the file extend
beyond the end of the rdev, we have been relying on the range checking
of the rdev API rather than doing it explicitly.
This is fine in general, but it causes the problem that these errors
cannot be distinguished from I/O errors, and I/O errors always make the
whole cbfs_walk() fail. That means we will not return a successful
result from cbfs_mcache_build(), and leads to an odd discrepancy in how
certain kinds of corrupted CBFSes are treated with and without mcache.
This patch adds an explicit range check to make the behavior consistent.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ice2b6960284bd0c19be35b0607e5e32791e7a64c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
When running multiple tests, e.g. by using unit-tests target, it is hard
to differentiate, which output comes from which file and/or
configuration. This patch makes the output easier to analyze and
understand by using new wrapper macro cb_run_group_tests(). This macro
uses __TEST_NAME__ value (containing test path and Makefile test name)
as a group name when calling cmocka group runner.
Example:
Test path: tests/lib/
Makefile test name: cbmem_stage_cache-test
Test group array name: tests
Result: tests/lib/cbmem_stage_cache-test(tests)
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I4fd936d00d77cbe2637b857ba03b4a208428ea0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
On mainboards with Cezanne SOC, serial enabled FSP_M binary size is
greater than the size allocated in DRAM. Increase the allocated size for
FSP_M binary in DRAM to handle both debug and release FSP_M binaries.
Also adjust the verstage load address accordingly.
BUG=None
TEST=Build and boot to OS in guybrush with both debug and release FSP_M.
Perform warm, cold reboot and suspend/resume cycling for 10 iterations.
Change-Id: Ic6f90041e258039e691cbdb3a978cfe1f782642a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57293
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Before this patch EXTRA_CFLAGS were placed before many other options.
This made overriding impossible even, when necessary. This patch moves
EXTRA_CFLAGS to be placed after original CFLAGS, thus making option
overriding possible.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: If8394b151696eee4bd736d2fb1ad340209e05fbb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57181
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable this feature, and it can use the probe statement in devicetree
to cache of fw_config field as oem string.
BUG=b:191931762
TEST=With CBI FW_CONFIG field set to 0x8,
set probe AUDIO MAX98390_ALC5682I_I2S_4SPK in devicetree
dmidecode -t 11
OEM Strings
AUDIO-MAX98390_ALC5682I_I2S_4SPK
Change-Id: I93cd9ef2d1ad963e66c422cff17b083abf731046
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
When the override functionality looks for device match, check that
the probe list for both the devices matches exactly if probe list
exists for the base device. This ensures that if there are two devices
with same identity (e.g. I2C address or USB port #) but using
different properties (registers) controlled by different probe
statements, then the two devices are not incorrectly matched as the
same device.
The check for base device having a probe list is performed before
comparing the probe lists because a base device might not really have
any probe requirements at all. So, when overriding such a device,
there is no need to check for the probe list match.
BUG=b:187193527
TEST=Verified by adding two I2C devices in the override tree with the
same I2C address and chip but different probe statements and confirmed
that both the devices are present in generated static.c file.
Change-Id: Ib18868b336cf4ffc9aa38aee7c6f333a35d32fce
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change moves the hda device enabling from baseboard device tree
to override tree for the variants that did not provide any hda
specific nodes. This ensures that the probe statements are correctly
selected by the variant depending upon the configurations it
supports.
Change-Id: Ib7b36468f17fbd65eb3d7d9355fcf78148aeb44a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57123
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
volteer baseboard was currently enabling TBT(USB4) devices in
baseboard devicetree and also selecting the Kconfigs required for
resource allocation above 4G for the USB4 controllers. However, not
all volteer devices have USB4 support. This change fixes USB4 enabling
for volteer family by making the following udpates:
1. TBT devices are moved from baseboard devicetree to individual
override trees for the variants that actually support USB4.
2. When moving TBT devices to override tree, tbt_pcie_rp0 is marked as
on instead of hidden for all variants other than volteer
reference. This is because volteer reference is the only device that
has an asymmetric support for USB4 (i.e. does not support USB4 on C0
port).
3. Kconfig selection for PCIEXP_HOTPLUG is moved to Kconfig.name for
these variants.
Change-Id: If380dcb1ea1633b3a1d6932e769cb6ed0a2761c7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57112
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Processor hang is observed while hot plug unplug of TBT device. BIOS
should execute TBT PCIe RP RTD3 flow based on the value of
TBT_DMA_CFG_VS_CAP_9[30]. It should skip TBT PCIe RP RTD3 flow, if
BIT30 in TBT FW version is not set.
BUG=b:194880254
Change-Id: Ie3577df519f64c6f7270dc5537278af76536774e
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56503
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DEV0 - 0x3a i2c-MX98390:00: Right Speaker
DEV1 - 0x3b i2c-MX98390:01: Left Speaker
DEV2 - 0x38 i2c-MX98390:02: Right Tweeter
DEV2 - 0x39 i2c-MX98390:03: Left Tweeter
This is to consist with other 2 speakers configs, and m/c driver design.
uid0/1 = regular speakers.
uid2/3 = tweeter
BUG=191931762
TEST=FW_NAME=redrix emerge-brya coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I0a3183b1e1ecbb109258d6e076551158e0b40ce1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
It would be easier for people to find the defined variables.
Change-Id: I6d181f6602aa5d55019ea2110b2d8e1fa7e0159c
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
On Braswell this is done in the bootblock before C code is executed.
Change-Id: I72c7b821e04169ae237d8adb6a8348f06e87b047
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
In CB:56884 we discussed changing the default fast_read speed from
66MHz, which some platforms may not be capable of running, to 33MHz,
which should be generally suitable for all platforms. This same
change has been applied to the default for all SPI speeds.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ibf926df6829ffdcbae947aaa245356f219615ce8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57148
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add buffer_end() function to common.h. This function returns a
pointer to the end of the buffer (exclusive).
This is needed by elogtool util. (See the next CL in the chain).
BUG=b:172210863
Change-Id: I380eecbc89c13f5fe5ab4c31d7a4fef97690a791
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ic7396b8429e29739e18a189dacea3a76e571cd58
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57049
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Using tablet mode of fw config to decide to load custom wifi sar or not.
BUG=b:194163604
TEST=build and test on cret and cret360
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: Ie94c2a07ad43fe1cb426e543dd97ed0434c42f2d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
commit de7262f82cdc1a7c868dbc9ca41e186e885eb2ba (soc/amd: remove special
GPIO_2 override soc_gpio_hook) removed the workaround that needed those
definitions, so remove the now unused GPIO_2_EVENT definitions.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3f3e3061eade0e0cd25e2263451ccf6cefdc4ea4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56812
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The `smbios_get_device_type_from_dev()` function is only called once
from the `smbios_walk_device_tree_type41()` function. Put the former
function's definition above the latter function's, instead of having
them a thousand lines apart.
Change-Id: Idc6175324ca8a14841eaf7d6904712efb75f2d26
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57205
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPD support to gimble for LPDDR4 memory part K4UBE3D4AA-MGCR.
BUG=b:191574298
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ida21fd50129412af59a341dea45232fd0f9931ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57253
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FSP-S disables UART #0 as per the `SerialIoDevMode` settings.
Change-Id: Ic1f9f7ce6fd4f453200d563bd8556946eef1b287
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Mimoja <coreboot@mimoja.de>
|
|
Commit 98ec53bdf15ff79369307862e71142d4606f9e5a (mb/google/caroline:
Re-enable I2C2 / fix digitizer) enabled I2C #2 in the `SerialIoDevMode`
array, but left the device disabled in the devicetree. Enable it.
Change-Id: I67eec1c753bfd2a78ed0c1e0a78057cd4a3d4153
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
FSP-S configures the GPIOs for enabled SerialIO devices. However, Poppy
boards only enable UART 0 because it's function 0 of PCI device 30, and
the PCI specification requires that function 0 of multifunction devices
be implemented if other functions are implemented as well.
Nautilus got remedied in commit 8a1f095e50e068e42d378f47c79467e7b6295b7b
(mb/google/poppy/variants/nautilus: Update camera power enable GPIOs) by
using `PchSerialIoSkipInit` for UART 0, which tells FSP to not touch the
SerialIO device. This way, it remains enabled and the GPIO settings will
not be overwritten by FSP.
However, not all variants do this, but use some UART 0 pads as GPIOs. To
prevent any issues, configure UART 0 as `PchSerialIoSkipInit` on all the
variants.
Change-Id: I7e3a61769ef9e3b348ce84c663f67d3c4c5d9485
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55236
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change can make the code be more flexible. And later we will use
amd_cb_config to transfer parameters.
Change-Id: Ic726aa9fc5f67803210af71d3e9cf2438b7e2a9b
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57062
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The issue is reported by Coverity. Using strcpy or strcat copying
string without checking length may cause overflow.
BUG=b:188769921
Reported-by: Coverity (CID:1438964)
Change-Id: I609d9ce405d01c57b1847a6310630ea0341e13be
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54946
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make sure that the 48MHz clock output that is typically used as a clock
source for an I2S audio codec or a Super I/O chip.
TEST=On Guybrush before and after this patch the final state of
MISC_CLK_CNTL0 is 0x1006044, so BP_X48M0_OUTPUT_EN is set in both cases.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I38be344a95ccf166c344b2bddcb388fea437a4df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56528
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the SPI configuration has been moved into Kconfig, it is no
longer needed in devicetree.
BUG=b:194919326
TEST=Build & boot guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ifdcd3f33173194c4a25794137756b143751edd70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:194919326
TEST=See SPI settings in bootblock
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I8ee8981986990240b09414cde8b84d9b109cb5b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This patch adds code to print the current SPI speeds for each of the 4
different speeds, Normal, Fast-read, Alt-mode, & TPM. It also displays
the SPI mode and whether or not SPI100 mode is enabled.
BUG=b:194919326
TEST: Display the speed, change speeds, show that new speeds are the
expected values.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I7825a9337474c147b803c85c9af7f9dc24670459
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add the fch_spi_early_init call in fch_pre_init to perform early SPI
initialization which enables SPI ROM and setting the speed & read modes.
BUG=b:194919326
TEST=Build and boot to OS in Guybrush.
Change-Id: Ibfbe6e16bd6b0dd46c13cecf2a35f0c0b4576b88
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56684
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get the settings for fast-read and mode from EFS, and reprogram those.
Program Normal reads, Alt-mode, and TPM speeds from Kconfig settings.
BUG=b:195943311
TEST=Boot and see that SPI was set to the correct speed & mode
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I8a24f637b2a0061f60a8f736121d224d4c4ba69b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The common_i2c_save struct isn't specific to the I2C code and since it
contains the state of the GPIO control & status register and the state
of the GPIO MUX register, move it to include/amdblocks/gpio_banks.h and
rename it to soc_amd_gpio_register_save.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If7cd47e5a32427d856948e319de8dfad8c928e96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
No need to strip the quotes of the FSP-M file path in the size check and
it's always a good idea to not remove the quotes around file paths that
will get passed as parameters to shell programs so that spaces in the
path can't cause malfunction.
TEST=All cases still behave as expected for Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Nico Huber <nico.h@gmx.de>
Change-Id: Ieeea84b5861f9d15b2472208432169dc8e3f0049
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This fix will enable PCIe x1 slot for ADL-M LP4 and LP5 RVPs.
The BDF for this PCIe slot is pci is: 0000:00:1d.0
TEST = show device command:
$ lspci -s 00:19.0
expect this:
00:19.0 Serial bus controller [0c80]: Intel Corporation Device 51c5
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ia988fa0b5d8fefe68503b39843aab06c4229b36f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57053
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on latest schematic to update the gpio table.
BUG=b:197308586
BRANCH=None
TEST=emerge-brya coreboot
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I0d91199ffd2128a136ea0a33dfe7affa77ae61d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Based on latest shcematic to update the device tree.
BUG=b:197308586
BRANCH=None
TEST=emerge-brya coreboot
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I59601571c5e4c2d19738cb333605fb22e1ea0d2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable flag SOC_INTEL_COMMON_BLOCK_TCSS.
BUG=b:187385592
TEST=type-C pendrive/Gen-2 SSD detected as Super speed.
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.com>
Change-Id: Ie3cb8b8836b17fa00ab0089d03fca9f22c4d702e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54090
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to schematics, TSR2 thermal sensor is not present in driblee.
BUG=b:191732473, b:197180925, b:195868075
BRANCH=keeby
TEST=FW_NAME="driblee" emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I343a6161f71f66b77d23f1fa2f581aaee5eddf1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57091
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the combination audio CS42L42 and amp. MAX98360.
BUG=b:195619349, b:191732473
BRANCH=keeby
TEST=FW_NAME="driblee" emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I264c680ed5638b71c912253a38c27152a9015d4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Power down the eMMC controller via the AOAC interface when it's not
enabled in the devicetree.
BUG=b:184978118
TEST=On guybrush the unused eMMC controller is disabled in AOAC after
applying this patch. Before this patch it was enabled.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I18f4626a29fdc422218777058341b0eae401bcd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55537
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
NCT6776's data sheet does say that the virtual LDN of GPIO base should
be 0x308, and most mainboards using it usually correctly config it in
devicetree.cb under the path 2e.308, but in nct6776.h it used to be
defined as 8 from the beginning (an ancient commit 1e3a22649a9, lately
revived in commit f95daa510d6), identical to the LDN of WDT, which
eliminates the definition of value 2e.308, and makes related resource
allocations unable to take effect. (in log we can find "PNP: 002e.308
missing read_resources" if 2e.308 is enabled and assigned with
resources)
In this commit, NCT6776_GPIOBASE is set to a value consistent with the
data sheet.
With this commit, resources under 2e.308 of NCT6776 can be allocated
successfully.
Change-Id: I604bad7ab34a8f57262fdec508e5952cf8eabf1c
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change follows other Intel SoCs common way to support SKUs with
bsp lapic_id != 0 by removing hardcoded lapic 0 from devicetree.cb and
allowing its detection at boottime. It completes support for HCV/DNV
after base SoC patch: commit ba936ce5db819d5ecb34e83a998b2390ecbdc4b9
soc/intel/denverton_ns: Ensure CPU device has a valid link
Link: https://mail.coreboot.org/hyperkitty/list/coreboot@coreboot.org/thread/YLMK2FBWWL6RKDNKBVZB3NJDYMEYHED7/
"A different lapic number in devicetree.cb needed for CPU with the same SKU and steping (Intel Atom C3538)."
Change-Id: I88f60f64d2beb2768ec9833de582d7901f456b11
Signed-off-by: Mariusz Szafrański <mariuszx.szafranski@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: King Sumo <kingsumos@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When CONFIG_FSP_M_FILE isn't defined, the parameter of the file-size
call evaluates to an empty string, so the file-size call will run
"cat | wc -c" which will cause make to get stuck in there. Also print a
message when no FSP-M file is specified that the resulting image won't
boot successfully.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b02774e2c79d12554fd076aa01bbe972176f372
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This documentation doesn't add any more value. Thus, remove it.
Change-Id: I0402bc736c6cc77d88a836bddce8eadae8ec5d7c
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Since all mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, make it the
default by changing its enum value to 0 and remove its configuration
from all related devicetrees.
If `common_soc_config.chipset_lockdown` is not configured with
something else in the devicetree, then `CHIPSET_LOCKDOWN_COREBOOT`
is used.
Also, add a release note for the upcoming 4.15 release.
Change-Id: I369f01d3da2e901e2fb57f2c83bd07380f3946a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Modify USB 2.0 port5 parameter to improve SI diagram measurement.
BUG=b:187992881
TEST= Pass USB 2.0 SI Eye diagram measurement.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I1eff05a7ad6563898744c24f9657e28625319873
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO_CODEC_SOURCE field of fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:194356991
TEST=ALC5682-VD/ALC5682-VS audio codec can work
Change-Id: I71b824c42c13cc2a8bebe0072de4a65ce238f074
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add supported memory part in the mem_parts_used.txt and generate the
SPD ID for the part. The memory part being added is:
MT53E512M32D1NP-046 WT:B
BUG=b:194223174
BRANCH=dedede
TEST=Build the boten board.
Signed-off-by: stanley.wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I36fcbf7333fd9e85b28baa64676f8435aca63889
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add supported memory parts in mem_parts_used.txt, and generate
SPD id for these parts.
MT53E1G32D2NP-046 WT:A
H9HCNNNBKMMLXR-NEE
K4U6E3S4AA-MGCR
MT53E512M32D2NP-046 WT:E
H9HCNNNCPMMLXR-NEE
K4UBE3D4AA-MGCR
H9HCNNNFAMMLXR-NEE
MT53E2G32D4NQ-046 WT:A
MT53E512M32D1NP-046 WT:B
MT53E1G32D2NP-046 WT:B
BUG=b:197850509
TEST=build pass
Change-Id: Ib7bdab1396138d728ae053c30656a9c80dddaff8
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update the I2C ports and touchpad based on the schematic.
BUG=b:195622489, b:191732473
BRANCH=keeby
TEST=FW_NAME="driblee" emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I8778ad6564e526e029c46c36c78e38f764e3c6b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56998
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the USB port configuration based on driblee schematic.
USB2 [0]: USB Type C Port 0
USB2 [1]: None
USB2 [2]: USB Type A Port 1
USB2 [3]: None
USB2 [4]: None
USB2 [5]: Camera UFC
USB2 [6]: None
USB2 [7]: None
USB3 [0]: USB Type C Port 0 (M/B side)
USB3 [1]: None
USB3 [2]: USB Type A Port 0 (M/B side)
USB3 [3]: None
BUG=b:195622487, b:191732473
BRANCH=keeby
TEST=FW_NAME="driblee" emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Id9f4f8db98cb20db1c3936c65689a847a7802b9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56997
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
