summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-07-10max77802: add header for max77802 PMICDavid Hendricks
This adds register offsets and important values for the Maxim MAX77802 PMIC. Change-Id: I3724b82bcb235b6684d2b976876f628f1ffbed3f Signed-off-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: http://review.coreboot.org/3747 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ARM: when setting a GPIO to put, set the value, then the directionRonald G. Minnich
We saw a problem on x86 last year in which setting direction, then value, glitched the output and caused problems. Change this code to set the output, then the direction. Change-Id: I3e1e17ffe82ae270eea539530368a58c6cfe0ebe Signed-off-by: Ronald G. Minnich <rminnich@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3679 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynox5420: Remove the 5250 clock registers and fix the SPI frequency.Gabe Black
The 5420 clock code still had a data structure in it for the 5250 clock registers which was used by some of the clock functions. That caused some clocks to be configured incorrectly, specifically the i2c clock which was running at about 80KHz instead of about 600KHz as configured by U-Boot. Also, the registers and bit positions used to set up the SPI bus were not consistent with U-Boot, and if the bus clock rate were set to 50MHz, a rate which has historically worked on snow, loading would fail. With these fixes the clock rate can be set to 50MHz and the device boots as much as is expected. I haven't yet measured the actual frequency of the bus to verify that it's now being calculated correctly. Change-Id: Id53448fcb6d186bddb3f889c84ba267135dfbc00 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3678 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10PIT: memory setupRonald G. Minnich
Tested and working. Gets us to ramstage. Change-Id: Ib9ea4a6c912e8152246aaf4f1f084a4aa1626053 Signed-off-by: Ronald G. Minnich <rminnich@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3677 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5420: add I2C8-10 to clock_get_periph_rate()David Hendricks
This adds entries for I2C8-10 to giant switch statement in clock_get_periph_rate(). It also eliminates the I2C peripheral's usage of clk_bit_info since it's confusing and error-prone. Change-Id: I30dfc4c9a03fbf16d08e44e074189fb9021edb6d Signed-off-by: David Hendricks <dhendrix@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3676 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10armv7a: Enable native memcpy / memsetStefan Reinauer
The code has been there for quite a while but was never enabled. Change-Id: I4ec3dcbb3c03805ac5c75872614e5d394df667cf Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3675 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5420: Implement support for the pinmux as functions.Gabe Black
Change-Id: I5e0ec360597cd95cb6510fb32b04d8931e6a33db Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3674 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5250: De-switch-ify the pinmux configuration code.Gabe Black
The pinmux code for the exynos5250 was all bundled into a single, large function which contained a switch statement that would set up the pins for different peripherals within the SOC. There was also a "flags" parameter, the meaning of which, if any, depended on which peripheral was being set up. There are several problems with that approach. First, the code is inefficient in both time and space. The caller knows which peripheral it wants to set up, but that information is encoded in a constant which has to be unpacked within the function before any action can be taken. If there were a function per peripheral, that information would be implicit. Also, the compiler and linker are forced to include the entire function with all its cases even if most of them are never called. If each peripheral was a function, the unused ones could be garbage collected. Second, it would be possible to try to set up a peripheral which that function doesn't know about, so there has to be additional error checking/handling. If each peripheral had a function, the fact that there was a function to call at all would imply that the call would be understood. Third, the flags parameter is fairly opaque, usually doesn't do anything, and sometimes has to have multiple values embedded in it. By having separate functions, you can have only the parameters you actually want, give them names that make sense, and pass in values directly. Fourth, having one giant function pretends to be a generic, portable API, but in reality, the only way it's useful is to call it with constants which are specific to a particular implementation of that API. It's highly unlikely that a bit of code will need to set up a peripheral but have no idea what that peripheral actually is. Call sights for the prior pinmux API have been updated. Also, pinmux initialization within the i2c driver was moved to be in the board setup code where it really probably belongs. The function block that implements the I2C controller may be shared between multiple SOCs (and in fact is), and those SOCs may have different pinmuxes (which they do). Other places this same sort of change can be made are the pinmux code for the 5420, and the clock configuration code for both the 5250 and the 5420. Change-Id: Ie9133a895e0dd861cb06a6d5f995b8770b6dc8cf Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3673 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ARM: Tell the linker memset and memcpy are functions.Gabe Black
The memset and memcpy functions are assembled as ARM code, likely because that's the default of the assembler. Without special annotation, the assembler and linker don't know that those symbols are functions which need special handling so that ARM/thumb issues are handled properly. This change adds that annotation which gets those functions working in Coreboot which is compiled as thumb. Libpayload and depthcharge are compiled as ARM so they don't *need* the annotation since it just works out in ARM mode, but it's the safe thing to do in case we change that in the future. We should explicitly select ARM vs. thumb when assembling assembly files to be consistent across builds and toolchains. Change-Id: I814b137064cf46ae9e2744ff6c223b695dc1ef01 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3672 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ARM: Separate the early console (romstage) from the bootblock console.Gabe Black
It might be that you want an early console in romstage before RAM is up, but you can't or don't want to support the console all the way back in the bootblock. By making the console in those two different environments configurable seperately that becomes possible. On the 5250 console output as early as the bootblock works, but on the 5420 it only starts working in the ROM stage after clocks have been initialized. Change-Id: I68ae3fcb4d828fa8a328a30001c23c81a4423bb8 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3671 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10google/pit: Don't spew output with GPIO configStefan Reinauer
There are hundreds of GPIOs on the Exynos5420. Don't always print all of them per default. Change-Id: I2152ab760e31a335dbcd9d6ad32cd1eaae4b89bc Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3670 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10arch: clean up Kconfig and MakefileStefan Reinauer
remove some unused code Change-Id: I41602fb391c1910c588a4f9dcc7c2edefe8ab5bc Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3669 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5420: Clear the framebuffer before making it uncacheableStefan Reinauer
If we clear the framebuffer and then flush it back to memory using cache operations, the writes are going to be full cachelines at a time. If we make it uncacheable first, the writes will be serialized writes of whatever sized chunks memset uses, probably 4 bytes or less. Change-Id: I960f87a370e97f9e91236ad796d931573bb3dbb8 Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3668 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5420: Don't disable and re-enable the MMU when uncaching the framebufferStefan Reinauer
At one time it seemed to be necessary to disable and then re-enable the MMU when setting the framebuffer to be uncache-able due to bugs in the MMU management code. Since those bugs have been fixed, this is no longer necessary. Change-Id: I7ce825cf5eaaa95119364d780cba0935752e4632 Signed-off-by: Gabe Black <gabeblack@chromium.org> Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Reviewed-on: http://review.coreboot.org/3667 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5420: Simplify the graphics code by eliminating the unused color mapStefan Reinauer
The code that allocated space for the framebuffer was adding space for a vestigial color map which was never used. It was also passing around a structure which was used to calculate a single value which was already known when that structure was put together. Eliminate the extra space, and pass the single value instead of the structure. Change-Id: I29bc17488539dbe695908e47f0b80c07e102e17d Signed-off-by: Gabe Black <gabeblack@chromium.org> Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Reviewed-on: http://review.coreboot.org/3666 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5420: Fix some problems with the clock management code.Gabe Black
The code which figured out the rate of the input clock to a peripheral was doing several things wrong. First, it was using the wrong values when determing what the source of a clock was set to. Second, it was using the wrong offset into that register to find the current source setting. This change fixes the constants which select a clock source which get some more things working, but doesn't attempt to fix the bit position table. Change-Id: Id7482ee1c78cec274353bae3ce2dccb84705c66a Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3665 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10armv7: Reserve space BL1 and checksum header by specifying bootblock offset.Hung-Te Lin
Not all ARM systems need "BL1", and the layout of BL* and bootblock may be different (ex, Exynos 5250 may use a new BL1 with variable length checksum header). To support that better, define the real base address (and ROM offset) of boot block, and then we can post-processing ROM image file by filling data / checksum and any other information. Change-Id: I0e3105e52500b6b457371ad33a9aa546acf28928 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3664 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10cpu: Add CPU microcode file to cbfs with 16-byte alignmentAaron Durbin
On x86 there is a 16-byte alignment requirement for the addresses containing the CPU microcode. The cbfs files containing the microcode are used in memory-mapped fashion when loading new mircocode. Therefore, the data payload's address/offset of a cbfs file in flash dictates the resulting alignment. Fix this by processing the CPU microcode cbfs file separately as it uses $(CBFSTOOL) to find the proper location within the provided rom image. Change-Id: Ia200d62dbcf7ff1fa59598654718a0b7e178ca4c Signed-off-by: Aaron Durbin <adurbin@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3663 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ec: Reserve correct ioport regions for Chrome OS EC to useBill Richardson
The LPC-based ChromeOS EC uses several ioport regions to communicate with the AP. In order for the new unified userspace access method to work, we need them to be reserved by the BIOS. Before /proc/ioports shows: 0800-0803 0804-08ff We'd like just a single 256-byte region at 0x800, but ASL can't handle that. So this will work: 0800-087f 0880-08ff Change-Id: I3f8060bff32d3a49f1488b26830ae26b83dab79d Signed-off-by: Bill Richardson <wfrichar@chromium.org> Reviewed-on: http://review.coreboot.org/3746 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10google/snow: Don't spew output with GPIO configStefan Reinauer
There are hundreds of GPIOs on the Exynos5250. Don't always print all of them per default. Change-Id: Ie349f2a4117883302b743027ed13cc9705b804f8 Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3661 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10slippy/falco/peppy: Enable SERIRQ continuous modeDuncan Laurie
The Chrome EC still does not tolerate SERIRQ in quiet mode and so the keyboard does not work properly. Change-Id: I9ab052187c9926ce0e2c86b86dfe987dd6564c1b Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/3745 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ec: Add romstage function for checking and rebooting ECDuncan Laurie
Now that we are executing VbInit() in coreboot we can end up in a situation where the recovery reason is consumed during VbInit (end of romstage) and then the EC is rebooted to RO during ramstage EC init, thereby losing the recovery reason. Two possiblities are to remove the EC check+reboot from ramstage and let it happen in depthcharge. This however means that the system has to boot all the way into depthcharge and then reboot the EC and the system again. Instead if we do a check in romstage before VbInit() is called then we can reboot the EC into RO early and avoid booting all the way to depthcharge first. This change adds a ramstage version the EC init function and calls it from the shared romstage code immediately after the PCH decode windows are setup. Change-Id: I30d2a0c7131b8e4ec30c63eea36944ec111a8fba Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/3744 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10chrome ec: Update EC header from EC repositoryDuncan Laurie
- Updated ec_commands.h is copied in directly from EC repo - Removed "old" interface and update resources for "new" interface - Updated temp sensor constants and added "not calibrated" - Update mainboards to remove check for EC_SWITCH_KEYBOARD_RECOVERY Change-Id: Ic93c1914f86b6f5bc224178270624ed92b5c1e15 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/3743 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10Drop ELF remains from boot codeStefan Reinauer
This stuff is not used, so let's drop it. Change-Id: I671a5e87855b4c59622cafacdefe466ab3d70143 Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3660 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ARMv7: flatten arch/armv7 source treeStefan Reinauer
With only 19 source files it doesn't make a whole lot of sense to create sub directories in arch/armv7, especially since the files were distributed somewhat randomly. Change-Id: I029c7848e915edf1737e1c401c034837c95d179d Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3659 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5420: Replace the 5250 clock logic with 5420.Gabe Black
The new code is stolen from U-Boot with little or no understanding of how it works. Change-Id: I3de7d25174072f6068d9d4fdaa308c0462296737 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3658 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5420: Make the ps_hold_setup function public.Gabe Black
This function had been declared in a public header file, but was marked static when actually defined. Change-Id: Ia551a5a12e7dbaf7bc00861e085695145ab7b91a Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3657 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10Exynos5420: Clean up console codeStefan Reinauer
- Don't initialize console twice in the bootblock - remove printk in memory init that would mess up the UART - unconditionally run console_init() in romstage, as it is also unconditionally run in the bootblock. Change-Id: I983d011c6ca602445f447d17799c1b2a33e8bd1d Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3656 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ec: Remove hardcoded GPI offset in EC SCIDuncan Laurie
With LynxPoint-LP the SCI GPE is no longer a GPIO that is offset by 16. Remove the Add and fix up the link definition so it is still accurate. Change-Id: I091141183a09345b5ffe28365583e48019f9f5e5 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/3742 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5250: Clear the framebuffer before making it uncacheable.Gabe Black
If we clear the framebuffer and then flush it back to memory using cache operations, the writes are going to be full cachelines at a time. If we make it uncacheable first, the writes will be serialized writes of whatever sized chunks memset uses, probably 4 bytes or less. Change-Id: I1b81731cfed00ae091ba6357451ab186d16f559e Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3655 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5250: Don't disable and re-enable the MMU when uncaching the framebuffer.Gabe Black
At one time it seemed to be necessary to disable and then re-enable the MMU when setting the framebuffer to be uncache-able due to bugs in the MMU management code. Since those bugs have been fixed, this is no longer necessary. Change-Id: I5f7b9bd14dc9929efe1834ec9a258d388b8c94e9 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3654 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ARM: Fix up page table/cachability management.Gabe Black
When modifying the page tables, use writel to ensure the writes happen, flush the page tables themselves to ensure they're visible to the MMU if it doesn't look at the caches, and invalidate the right TLB entries. The first two changes are probably safer but may not be strictly necessary. The third change is necessary because we were invalidating the TLB using i which was in megabytes but using an instruction that expects an address in bytes. One symptom of this problem was that the framebuffer, which was supposed to be marked uncacheable, was only being partially updated since some of the updates were still in the cache. With this change the graphics show up correctly. Change-Id: I5475df29690371459b0d37a304eebc62f81dd76b Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3653 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5250: Simplify the graphics code by eliminating the unused color map.Gabe Black
The code that allocated space for the framebuffer was adding space for a vestigial color map which was never used. It was also passing around a structure which was used to calculate a single value which was already known when that structure was put together. Eliminate the extra space, and pass the single value instead of the structure. Change-Id: Ia6a41cefdf8b29fe7d68f9596a156eced6eb5df8 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3652 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10snow: Make coreboot set up pins for busses it knows are hooked up as suchGabe Black
Coreboot knows that, for the snow board, certain pins are to be connected to bus controllers in the SOC and to the wires of a bus external to the SOC. It can configure them as such and free its payload from having to know how to set everything up. Change-Id: I1bb127c810e9ee077afc4227a6f316eaa53d6498 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3650 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins)
2013-07-10drivers: Fix spellingMartin Roth
Change-Id: Ib0d98e3ab5b2943c36f88765587e8963a4f49604 Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/3754 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ec: Fix spellingMartin Roth
Change-Id: I5e4d35572c43f07bec5ec0bcd75c717723228e2f Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/3757 Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10lib: Fix spellingMartin Roth
Change-Id: I999987af9cb44906e3c3135c0351a0cd6eb210ff Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/3756 Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10device: Fix spellingMartin Roth
Change-Id: I53a40d114aa2da76398c5b97443d4096809dcf36 Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/3730 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10console: Fix spellingMartin Roth
Change-Id: I1fef27c4a16ee4358ace8014a8d6e9fa92c4f790 Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/3728 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10arch: Fix spellingMartin Roth
Change-Id: Ifea10f0180c0c4b684030a168402a95fadf1a9db Signed-off-by: Martin Roth <martin.roth@se-eng.com> Reviewed-on: http://review.coreboot.org/3727 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ARM: Fix the way the space for the page tables is allocated.Gabe Black
The page tables need to be aligned to a 16KB boundary and are 16KB in size. The CBMEM allocator only guarantees 512 byte alignment, so to make sure things are where they're supposed to be, the code was allocating extra space and then adjusting the pointer upwards. Unfortunately, it was adding the size of the table to the pointer first, then aligning it. Since it allocated twice the space of the table, this had the effect of moving past the first table size region of bytes, and then aligning upwards, pushing the end of the table out of the space allocated for it. You can get away with this if you push things you don't care about off the end, and it happened to be the case that we were allocating a color map we weren't using at the start of the next part of cbmem. Change-Id: I6b196fc573801b02f27f2e667acbf06163266651 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3651 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5250: When enabling the I2S pins, turn off pull ups/downs.Gabe Black
These pins will be driven by the internal controller which shouldn't have pull ups or downs in the pin fighting with them. Change-Id: I579aed84ace45d8f5f1d3ca64c064d98de842b57 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3649 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10exynos5420: Replace the 5250 GPIO code with code that should work on 5420.Gabe Black
Change-Id: Iac6615240e94c74037afc801169c32d3ebc4ac03 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3648 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ARMv7: Clean up console codeStefan Reinauer
- Guard console_init() with CONFIG_EARLY_CONSOLE in bootblock - Don't initialize console twice in the bootblock - remove printk in memory init that would mess up the UART - unconditionally run console_init() in romstage, as it is also unconditionally run in the bootblock. Change-Id: I8f0d60877433162367074d0e55e01f935fd81f8e Signed-off-by: Stefan Reinauer <reinauer@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3647 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10pit: Add a "pit" mainboard which is mostly a copy of "snow".Gabe Black
This change adds a pit mainboard which is mostly a copy of snow, except that mentions of the 5250 were replaced with the 5420, and mentions of snow were replaced with pit. Change-Id: I8eb0ce379eb2fa353bb88d5656a0c5e2290afbf0 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3646 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10pit: Fix some settings for the exynos5420 CPU.Gabe Black
Some of the settings which were defaulted to or automatically selected for the exynos5420 which were inherited from the exynos5250 were not correct for this SOC. Change-Id: I11ffd8a6b80628405ac493fe2139f79c05d15d7e Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3645 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10pit: Create an exynos5420 directory which is nearly a copy of exynos5250.Gabe Black
This change creates an exynos5420 directory with code that will eventually implement support for the exynos5420 cpu from Samsung. Currently it's a copy of the exynos5250 directory with the name changed. There are going to be some problems where headers in src/cpu/samsung/exynos-common include headers in the exynos5250 directory directly. Change-Id: Ia8d7244310d32499238bbc171c0c668ec48178e1 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3644 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ARMv7: De-uboot-ify Exynos5250 GPIO codeStefan Reinauer
The Exynos GPIO code has three different APIs that, unfortunately, were widely used throughout the code base. This patch is cleaning up the mess. Change-Id: I09ccc7819fb892dbace9693c786dacc62f3f8eac Signed-off-by: Stefan Reinauer <reinauer@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3643 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ARMv7: De-uboot-ify Exynos5250 codeStefan Reinauer
When starting the Exynos5250 port, a lot of unneeded u-boot code was imported. This is an attempt to get rid of a lot of unneeded code before the port is used as a basis for further ARM ports. There is a lot more that can be done, including cleaning up the 5250's Kconfig file. Change-Id: I2d88676c436eea4b21bcb62f40018af9fabb3016 Signed-off-by: Stefan Reinauer <reinauer@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3642 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10Update 3rdparty hash for latest ARM BL1 binariesStefan Reinauer
Change-Id: Ice28114e5f53f510d305cd85d095044e2f4bd7b2 Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/3740 Reviewed-by: Gabe Black <gabeblack@chromium.org> Reviewed-by: David Hendricks <dhendrix@chromium.org> Tested-by: build bot (Jenkins)
2013-07-10w83627hf/acpi: Fix endianess error in floppy drive enumeration codeChristoph Grenz
The enumeration results are stored as five DWORDs in one 20 byte buffer. Bytes 3, 7, 11 and 15 were used to set the lowest bit of each DWORD. ACPI uses little endian, so 1, 4, 8 and 12 are the correct indices. Change-Id: I793225cb1bb62fd148ecfa1e61e02f5d7be62cdb Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de> Reviewed-on: http://review.coreboot.org/3602 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-10samsung/exynos5250: unify codeStefan Reinauer
It turns out that the exynos5-common code previously imported from u-boot is not common code at all but very specific to the 5250 and not compatible with the 5450. Hence, unify the directories exynos5250 and exynos5-common. We will try to factor out common code while progressing with the 5450 port. Change-Id: Iab595e66fcd01eda8365c96fb8bef896f7602f03 Signed-off-by: Stefan Reinauer <reinauer@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3641 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10Wield battle axe at ARM portStefan Reinauer
This patch unfortunately incorporates a number of changes, all of which are making future ARM ports easier. - drop cruft that came in with u-boot - move serial console from mainboard Kconfig to Exynos Kconfig - factor out non-board specific wakeup code - move generic bootblock code from mainboard to Exynos - actually call arch_cpu_init() - remove dead code - fix up copyright messages - remove snow_ prefix from a lot of code to reduce the noise when creating a new mainboard based on that code. Change-Id: Ic05326edf5a7e1a691c5ff841a604cb9e351b562 Signed-off-by: Stefan Reinauer <reinauer@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3640 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10Rename hardwaremain() to main()Stefan Reinauer
... and drop the wrapper on ARMv7 Change-Id: If3ffe953cee9e61d4dcbb38f4e5e2ca74b628ccc Signed-off-by: Stefan Reinauer <reinauer@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3639 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ARMv7: normalize ramstage code flowStefan Reinauer
In ram stage, all code flow should be tied to the resource allocator. Stuff that has to happen before everything else goes into the mainboard enable function in mainboard.c. This patch empties the main() wrapper around hardwaremain.c, allowing to get rid of this special case in the ARM port. Change-Id: Ide91a23f1043b64acf64471f180a2297f0f40d97 Signed-off-by: Stefan Reinauer <reinauer@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3638 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10FUI: reorganize include filesRonald G. Minnich
We've got enough of a handle on this to realize some things: drm_dp_helper.h is by design device and architecture independent i915.h is common to most intel graphics chipsets going back several years i915_reg.h is as well Move these files to src/include/device, and adjust the .c files accordingly. Change-Id: I07512b3695fea0b22949074b467986420783d62a Signed-off-by: Ronald G. Minnich <rminnich@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3637 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10Provide support for setting up the framebuffer from EDIDRonald G. Minnich
Add three functions to edid.c: void set_vbe_mode_info_valid(struct edid *edid, uintptr_t fb_addr) takes an edid and uintptr_t, and fills in a static lb_framebuffer struct as well as setting the static vbe_valid to 1 unless some problem is found in the edid. The intent here is that this could be called from the native graphics setup code on both ARM and x86. int vbe_mode_info_valid(void) returns value of the static vbe_valid. void fill_lb_framebuffer(struct lb_framebuffer *framebuffer) copies the static edid_fb to lb_framebuffer. There is now a common vbe.h in src/include, removed the two special ones. In general, graphics in coreboot is a mess, but graphics is always a mess. We don't have a clean way to try two different ways to turn on a device and use the one that works. One battle at a time. Overall, things are much better. The best part: this code would also work for ARM, which also uses EDID. Change-Id: Id23eb61498b331d44ab064b8fb4cb10f07cff7f3 Signed-off-by: Ronald G. Minnich <rminnich@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3636 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10ChromeEC: Fix the default, depends for EC_GOOGLE_CHROMEEC_I2C.Gabe Black
The default for this variable should be n, it should only depend on EC_GOOGLE_CHROMEEC, and it should be (and is) explicitly enabled when needed. This prevents it from being turned on when the EC bus is SPI. Change-Id: Idc6651a764be4f055341a36b9b4a58990f050b0c Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3737 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10Drop some duplicates of PCI-e config functionsKyösti Mälkki
These are not specific to Intel. Further work needs to be done to combine these with MMCONF_SUPPORT in arch/io.h. Change-Id: Id429db2df8d47433117c21133d80fc985b3e11e4 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3502 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10Fix MMCONF_SUPPORT_DEFAULT for ramstageKyösti Mälkki
Define at one place whether to use IO 0xcf8/0xcfc or MMIO via MMCONF_BASE_ADDRESS for PCI configuration access funtions in ramstage. The implementation of pci_default_config() always returned with pci_cf8_conf1. This means any PCI configuration access that did not target bus 0 used PCI IO config operations, if PCI MMIO config was not explicitly requested. Change-Id: I3b04f570fe88d022cd60dde8bb98e76bd00fe612 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3606 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com> Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-07-10southbridge/intel/i82801gx: Make compilation possible with CONFIG_SMM_TSEGDenis 'GNUtoo' Carikli
Without that fix, and with CONFIG_SMM_TSEG, we have: src/southbridge/intel/i82801gx/smihandler.c: In function 'southbridge_smi_sleep': src/southbridge/intel/i82801gx/smihandler.c:340:3: error: implicit declaration of function 'smi_release_lock' [-Werror=implicit-function-declaration] cc1: all warnings being treated as errors make: *** [build/southbridge/intel/i82801gx/smihandler.smm.o] Error 1 The fix is modelled after src/cpu/x86/smm/smihandler.c which ifdefs smi_release_lock(). Change-Id: Icdc6d039b34a1d95d0e607419bba2484d21abc5e Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: http://review.coreboot.org/3281 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10i82801gx: smihandle: sync with southbridge/intel/bd82x6x/smihandler.cDenis 'GNUtoo' Carikli
Change-Id: Ic725b169061bd426aa8206dc1d6d31e67cc639f2 Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: http://review.coreboot.org/3304 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10southbridge: i82801gx: smihandler.c: Correct outl->outw mistake.Denis 'GNUtoo' Carikli
This mistake was spoted by comparison with the src/southbridge/intel/bd82x6x/smihandler.c file. Change-Id: I1516f0131d524bd7d001e6780e9a45402d1814d1 Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: http://review.coreboot.org/3303 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10sandybridge: Add option to lock SPI regions on resumeNico Huber
Add an option to mark all SPI regions write protected on each S3 resume. We were used to lock the SPI interface in the payload which isn't run on the resume path. So we have to do it here. For the write protection to be effective, all write opcodes in the opmenu have to be marked correctly (as write operations) and the whole SPI interface has to be locked. Both is already done. Change-Id: I5c268ae8850642f5e82f18c28c71cf1ae248dbff Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3594 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-09fox_wtm2: First step support for coreboot-based graphics startupRonald G. Minnich
This code is the initial version of FUI for haswell and wtm2. The code is simplified from before in many ways. I've gotten rid of the opcode table, because it obscured meaning and I don't think it is needed any more. Register sets, mainly used for reset, are just lines of code -- not many of them. There are a bunch of not-yet-documented registers here; the VBIOS seemed to think they were necessary and testing shows they seem to be right. As a bit of added paranoia, we always include the VBIOS code as our emergency recovery path. You have to run it now anyways, so this is no regression from our current situation; and, if all goes well, in a week (or so), you'll never have to run it again, but like the Force and nose hair, it will be with you always. The code can return in three ways. The first, best way is success: panel is up and the VBIOS need not run. The second mode is that we tried to light up the panel but could not, for some reason, but will return with the panel partly up. In this case, it's ok not to power cycle the panel. The third, worst case, which will NEVER happen, ha ha, is that we have to turn the panel off and wait the required 600ms for it to cycle. Life sucks sometimes. This failure mode is in the 'hang on we're going to fix it' category now that we have ramstage in RW. The Big Goal here is to create something other coreboot ports can use as well. The guys doing the x60 report that the link FUI works, without too many mods, on that chipset, so it seems Intel is keeping things from changing too much over time. Also, again, please note: this and the next 3 versions will ALWAYS fail. The goal is to verify the correctness of the recovery path. The bizarre tab-space formatting in drm_dp_helper.h is from the original, as in i915_reg.h Change-Id: I6ecf454633029d185c29d470980b5a0f3114a8ce Signed-off-by: Ronald G. Minnich <rminnich@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3635 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-09FOX_WTM2: First pass at FUI.Ronald G. Minnich
This lights up the display. We don't get graphics but we are missing the gttsetup at this point, so that is no shock. The real shock is that anything works at all. Change-Id: I03fc470334e96878aeb8465044b3cc9c90378735 Signed-off-by: Ronald G. Minnich <rminnich@google.com> Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3634 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-08msrtool: Fix verbose ignored by cpuid().Benoît Legat
This is a trivial patch moving cpuid() call after reading argv so that verbose is set. Change-Id: Ic621191ef650495614a041413c1a0f707d4469e6 Signed-off-by: Benoît Legat <benoit.legat@gmail.com> Reviewed-on: http://review.coreboot.org/3627 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-08Fix Vortex86EX devicetree.cb indentation.Andrew Wu
Change-Id: If357b55b91618ee2438e6c6b2efb7018c56d26d0 Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3628 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-08Revert "Radio and dock support in EC on X60 and X201"Peter Stuge
This reverts commit 7d1ebbff5ad224591a2d1972737611f96a13145c Change-Id: I4a9d0cd31a3df3d1e092193953f334697ca65167 Signed-off-by: Peter Stuge <peter@stuge.se> Reviewed-on: http://review.coreboot.org/3616 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-07-06am335x: Implement support for the UART.Gabe Black
This patch was started by Dave Hendricks and implements the procedure for setting up the UART as described in the manual. Some unused code was removed. Change-Id: If26a424cac401ef3eafaec081147f41184fbcee9 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3490 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Tested-by: build bot (Jenkins)
2013-07-05Add support for DMP Vortex86EX PCI mainboard.Andrew Wu
Change-Id: I8d42f765519e356d8f0cc6ed339d9b74f0a3e4d7 Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3610 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-04w83627hf/acpi: Fix offset of logical device activationNico Huber
The PnP's logical device activation normally resides at 0x30. This might have been overlooked as 0x29 looks very close to 0x30 in human eyes. Change-Id: Id5d5a92f2683ebe1808b943f686c062151d216da Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3592 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-07-04w83627hf/acpi: Fix type error in floppy drive enumeration codeChristoph Grenz
The enumeration method tried to evaluate an one-byte OperationRegion instead of a field in this OperationRegion, which resulted in an AE_TYPE error at runtime. Indexing the OperationRegion with a single field fixes this error. Change-Id: I15dd7aa6ecafb3a215d165d2b721003446815025 Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de> Reviewed-on: http://review.coreboot.org/3603 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-04intel/i5000: Use MMCONF_SUPPORT_DEFAULTKyösti Mälkki
Change all PCI configuration accesses to MMIO on two boards with i5000 chipset. To enable MMIO style access, add explicit PCI IO config write in the bootblock. Change-Id: I26f1c2da5ae98aeeda78bdcae0fb1e8c711a3586 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3601 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-04Move select MMCONF_SUPPORT under northbridge (fix)Kyösti Mälkki
I missed the board with gm45 when I moved MMCONF_SUPPORT lines. Also, the intel/i3100 does not have MMCONF_SUPPORT implemented even though it was previously selected for intel/eagleheights board. Change-Id: I9c7f6b0a150b4d54288a1e015277b9d98467fca4 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3598 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-04intel/i945: Use MMCONF_SUPPORT_DEFAULTKyösti Mälkki
Change all PCI configuration accesses to MMIO on all boards with i945 chipset. To enable MMIO style access, add explicit PCI IO config write in the bootblock. Change-Id: Ia1ab73f1a2dcda87db4eb9b2ffddc6f7b4382b01 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3584 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com> Reviewed-by: Nico Huber <nico.huber@secunet.com>
2013-07-04intel/sandybridge intel/ivybridge: Use MMCONF_SUPPORT_DEFAULTKyösti Mälkki
Change all PCI configuration accesses to MMIO on all boards with SandyBridge and IvyBridge. To enable MMIO style access, add explicit PCI IO config write in the bootblock. Change-Id: I8f957a80bf57df000897c5a080dd5ff131b1ec0d Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3576 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.huber@secunet.com>
2013-07-03Move select MMCONF_SUPPORT under northbridgeKyösti Mälkki
Move/remove MMCONF_SUPPORT reference under mainboard Kconfig, as that feature originates from northbridge and cannot be disabled for a single mainboard. Change-Id: I6d6861079876ddddaff90b10f18edb6936e93bd0 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3589 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-03Add support for DMP Vortex86EX PCI southbridge.Andrew Wu
Change-Id: Iad11cb1b22e9d1e2953b12221541b1478cad9665 Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3547 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-03winbond/w83627dhg: Fix logical device power down in ACPINico Huber
The W83627DHG has some power managements bits to power down individual logical devices. These are called `* Power Down`. Counterintuitively and in contrast to `Immediate Power Down` (bit to power down the whole chip), these bits are set when the respective logical device is powered. Unfortunately, our ACPI code set them wrong which led to disabled devices after a S3 suspend/resume. Adding an option how to set the PM bits and setting them to zero for the W83627DHG, corrects it. Tested with kontron/ktqm77. Change-Id: I8a472d480d4277721bd17c9f7c2ce44fa84e8ae2 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3590 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-03pnp: Add some default functions to enter/exit config stateNico Huber
Implement some common default functions to enter and exit the configuration state. Also provide default pnp_mode_ops for common enter()/exit() function pairs. The following cocci ensures their use: @ mode_match @ identifier enter, exit, ops; @@ struct pnp_mode_ops ops = { .enter_conf_mode = enter, .exit_conf_mode = exit, }; @ enter_match_8787 @ identifier mode_match.enter, dev; @@ enter(...) { outb(0x87, dev->path.pnp.port); outb(0x87, dev->path.pnp.port); } @ depends on enter_match_8787 @ identifier mode_match.enter, mode_match.ops; @@ struct pnp_mode_ops ops = { - .enter_conf_mode = enter, + .enter_conf_mode = pnp_enter_conf_mode_8787, }; @ enter_match_55 @ identifier mode_match.enter, dev; @@ enter(...) { outb(0x55, dev->path.pnp.port); } @ depends on enter_match_55 @ identifier mode_match.enter, mode_match.ops; @@ struct pnp_mode_ops ops = { - .enter_conf_mode = enter, + .enter_conf_mode = pnp_enter_conf_mode_55, }; @ depends on enter_match_8787 || enter_match_55 @ identifier mode_match.enter; @@ -enter(...) {...} @ exit_match_aa @ identifier mode_match.exit, dev; @@ exit(...) { outb(0xaa, dev->path.pnp.port); } @ depends on exit_match_aa @ identifier mode_match.exit, mode_match.ops; @@ struct pnp_mode_ops ops = { - .exit_conf_mode = exit, + .exit_conf_mode = pnp_exit_conf_mode_aa, }; @ depends on exit_match_aa @ identifier mode_match.exit; @@ -exit(...) {...} @ depends on enter_match_8787 || enter_match_55 || exit_match_aa @ @@ #include <device/pnp.h> +#include <superio/conf_mode.h> @ mode_match_55_aa @ identifier ops; @@ struct pnp_mode_ops ops = { .enter_conf_mode = pnp_enter_conf_mode_55, .exit_conf_mode = pnp_exit_conf_mode_aa, }; @@ identifier mode_match_55_aa.ops; @@ -struct pnp_mode_ops ops = {...}; @@ identifier mode_match_55_aa.ops, devops; @@ struct device_operations devops = { - .ops_pnp_mode = &ops, + .ops_pnp_mode = &pnp_conf_mode_55_aa, }; @ mode_match_8787_aa @ identifier ops; @@ struct pnp_mode_ops ops = { .enter_conf_mode = pnp_enter_conf_mode_8787, .exit_conf_mode = pnp_exit_conf_mode_aa, }; @@ identifier mode_match_8787_aa.ops; @@ -struct pnp_mode_ops ops = {...}; @@ identifier mode_match_8787_aa.ops, devops; @@ struct device_operations devops = { - .ops_pnp_mode = &ops, + .ops_pnp_mode = &pnp_conf_mode_8787_aa, }; Change-Id: I1480336b54523cc95210d99cf31c1a0b3a14b464 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/3484 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2013-07-02Intel GM45, 945, Sandy Bridge: Unify `delay.c` and `udelay.c`Paul Menzel
Use the same indentation, comment placement and spelling of words. Run `indent -linux …`. Change-Id: Id5765c45b28058cdd50ee4c0a1fd9f645ad7f3f8 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/3220 Reviewed-by: Nico Huber <nico.huber@secunet.com> Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-02Make setting MAX_PIRQ_LINKs depend on NORTHBRIDGE_VIA_VX900Dave Frodin
The MAX_PIRQ_LINKS is defined in src/Kconfig with a default value of 4. The src/northbridge/via/vx900/Kconfig also defines MAX_PIRQ_LINKS with a default of 8 and it ends up giving us a value of 8 for non-VIA platforms. Change-Id: Iee1938d38a93ab7c35c8cb6fe9656a92cf3fa21e Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/3586 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.huber@secunet.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-07-01w83627hf: Add comments about parallel port modes in superio.aslChristoph Grenz
Add comments in PAR0._PRS explaining which dependent resource descriptor puts the parallel port into EPP or SPP mode. Change-Id: If4e224dbaf6f9105cde88d995d2e7c74fbf14502 Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de> Reviewed-on: http://review.coreboot.org/3495 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.huber@secunet.com>
2013-07-01cbmem: Fix makefileStefan Tauner
The .dependencies rule did not use the CPPFLAGS variable which led to funny behavior: a spurious termination message the first time (after checkout/make distclean) one executes make. Afterwards the (wrongly) empty .dependencies file hides the problem and the binary is created anyway. $ make cbmem.c:37:34: fatal error: boot/coreboot_tables.h: No such file or directory compilation terminated. cc -O2 -Wall -Werror -iquote ../../src/include -iquote ../../src/src/arch/x86 -c -o cbmem.o cbmem.c cc cbmem.o -o cbmem $ make make: Nothing to be done for `all'. $ make clean rm -f cbmem *.o *~ $ make cc -O2 -Wall -Werror -iquote ../../src/include -iquote ../../src/src/arch/x86 -c -o cbmem.o cbmem.c cc cbmem.o -o cbmem $ make distclean rm -f cbmem *.o *~ rm -f .dependencies $ make cbmem.c:37:34: fatal error: boot/coreboot_tables.h: No such file or directory compilation terminated. cc -O2 -Wall -Werror -iquote ../../src/include -iquote ../../src/src/arch/x86 -c -o cbmem.o cbmem.c cc cbmem.o -o cbmem I fixed that by adding the CPPFLAGS variable to the .dependencies recipe, just like Stefan Reinauer did in Chromium (Ia9d2e10a3ef122f30d681d16c2291eb108ead835), hence the split sign-off for this tiny change. :) Change-Id: Icd11b146ad762cbdf9774630b950f70e1253a072 Signed-off-by: Stefan Reinauer <reinauer@google.com> Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at> Reviewed-on: http://review.coreboot.org/3548 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.huber@secunet.com>
2013-07-01beaglebone: Enable the clocks and pins for the configured UART.Gabe Black
Set up the pinmux to enable the pins and the clocks for whichever UART is currently configured. Change-Id: Iac13f16d9d84320555b99734ea83eafd0a2803fe Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3573 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-01am335x: Fix the address of the pinmux registers.Gabe Black
The pinmux register data structure describes a subset of the control module registers, but the address which pointed to the base of the pinmux registers was actually being set to the beginning of all the control module registers, not just those having to do with the pinmux. With this address fixed, the UART now works on the beaglebone black. Change-Id: I7c99b6f37d7da359af074127cd0c1a86fda2d9a0 Signed-off-by: Gabe Black <gabeblack@chromium.org> Reviewed-on: http://review.coreboot.org/3574 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-01usbdebug: Support i82801dx/ex southbridgeKyösti Mälkki
Tested on i82801dx system with board aopen/dxplplusu. Change-Id: I522455ac79c87b9b6fc9cd8c4dc0da3563dfbfad Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3381 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-07-01usbdebug: Unify Intel southbridge buildsKyösti Mälkki
EHCI controller enable is identical on the affected chipsets. Change-Id: I91830b6f5144a70b158ec1ee40e9cba5fab3fbc9 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3424 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-07-01usbdebug: Drop duplicates of EHCI BAR relocation codeKyösti Mälkki
All the additional work that needs to be done in EHCI BAR relocation is independent of the hardware platform and was functionally identical in all the copies removed. When USBDEBUG is not selected, PCI EHCI controllers use standard pci_dev_read_resources() call. With USBDEBUG selected, PCI EHCI controller's device_operations .read_resources is replaced with pci_ehci_read_resources() call, which in turn will replace the device_operations .set_resources call. The replacement for .set_resources reconfigures usbdebug driver side, and calls the original .set_resources to configure hardware side. Change-Id: I8e136a5da4efedf60b6dd7068c0488153efaaf8e Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3412 Reviewed-by: Aaron Durbin <adurbin@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-06-29AMD S3 resume: Add framwork to write bigger dataSiyuan Wang
This patch is based on 'AMD S3: Program the flash in a bigger data packet'[1] Some AMD south bridge can write bigger data when saving S3 info. In this patch, I use config 'AMD_SB_SPI_TX_LEN' to contral data size. AMD_SB_SPI_TX_LEN is defined in 'src/southbridge/amd/Kconfig' and then can be overridden in the Kconfig for specific southbridges that support larger size. I have tested on AMD Parmer and Thatcher. We will release a new board whose south bridge can transfer more than 4 bytes each time. [1] http://review.coreboot.org/#/c/2306/ Change-Id: Id984955d46eae487e39d45979f1a90054aa9f54b Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/3413 Tested-by: build bot (Jenkins) Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-28ELOG: Fix warning to fix the compilation.Denis 'GNUtoo' Carikli
Without that fix we have: src/drivers/elog/elog.c: In function 'elog_is_header_valid': src/drivers/elog/elog.c:213:3: error: format '%u' expects argument of type 'unsigned int', but argument 4 has type 'long unsigned int' [-Werror=format] Change-Id: I71b80a94c03a04eedb688ae107d92c05a878315e Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: http://review.coreboot.org/3551 Reviewed-by: Nico Huber <nico.huber@secunet.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-06-28libpayload: Add strerrorStefan Tauner
Change-Id: I33d45ad7d09473b8c6f5b7ee5fbadc0d184f9dcd Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at> Reviewed-on: http://review.coreboot.org/3537 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.huber@secunet.com>
2013-06-28Drop WARNINGS_ARE_ERRORS exceptionsStefan Reinauer
Thanks to Bruce's great work, we can finally drop this workaround. Change-Id: Ie92d1e53ef867fa34aa2489ccfb682d73195b213 Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/3569 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-28Supermicro H8SCM/H8QGI: Increase size of bus variable to meet APIBruce Griffith
Users of mptable_write_buses() pass two pass-by-reference parameters reflecting a maximum bus number and a search bus number. These bus numbers are expected to be held in "int" variables and are updated by the function. Both of the Supermicro boards define the search bus number as a byte value in mptable.c. For now, change the two Supermicro boards to use "int" to hold the search bus index. Change-Id: Ie71850719c1fa3cda0ac9c8773bb80650de95c70 Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-on: http://review.coreboot.org/3546 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-28AMD Dinar: Eliminate warnings (initializers/prototypes/unused var)Bruce Griffith
Fix a bunch of compiler-generated warning messages. These fixes are mainly braces for grouping initializers. These changes are not intended to change any code functionality. There are two changes where function prototypes are added, and two cases where unused variables are eliminated. Change-Id: I93cef8899170b5575e7fb7c55181b381a7bcd9d8 Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-on: http://review.coreboot.org/3545 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Zheng Bao <zheng.bao@amd.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-28AMD SB700 boards: Set Azalia configuration flagsBruce Griffith
The existing code for setting Azalia configuration assumes that the configuration bits are contiguous within a single byte and can be set using a byte copy addressed into the lowest 2-bit subfield. The fix in Family 14 defines a union that can be addressed as a byte to overlay the bit fields. Since the offset of the four subfields is not necessarily fixed, change the code to initialize each of the four subfields individually. Change-Id: I1dff20bb8bd3e1bcd8b4e6b0537e20779d2a3521 Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-on: http://review.coreboot.org/3544 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Zheng Bao <zheng.bao@amd.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-28supermicro/h8scm: Add a type cast for printk to correct a warning messageBruce Griffith
Copy a type cast from the other cases of the same switch statement to eliminate compiler warning messages. Change-Id: I8d0a88892f6a5f8e43227ab5f830041894b07f6a Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-on: http://review.coreboot.org/3543 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-28Dinar, H8SCM, H8QGI: Add prototype of get_bus_conf()Bruce Griffith
On Dinar, H8SCM, and H8QGI, add <cpu/amd/amdfam15.h> as an include to pick up the prototype definition of get_bus_conf(). Change-Id: Ie4887670ac52aa194745881362df19cd1d75773e Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-on: http://review.coreboot.org/3542 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Zheng Bao <zheng.bao@amd.com> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-28amd/cimx/sb700/late.c: Add type cast to (UINT8)Bruce Griffith
This change inserts a type cast to eliminate a compiler warning. Change-Id: If223f61f1565caeadb1b7e0762975b1b2412eda5 Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-on: http://review.coreboot.org/3541 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>