| Age | Commit message (Collapse) | Author |
|---|
|
AMD has rewritten AGESA (now at v9) for direct inclusion into UEFI
build environments. Therefore, unlike the previous Arch2008
(a.k.a. v5), it can't be built without additional source, e.g. by
combining with EDK II, and it has no entry points for easily
building it into a legacy BIOS.
AGESA in coreboot now relies on the FSP 2.0 framework published
by Intel and uses the existing fsp2_0 driver.
* Add fsp_memory_init() to romstage.c. Although Picasso comes out
of reset with DRAM alive, this call is added to maximize
compatibility and facilitate internal development. Future work
may look at removing it. AGESA reports the memory map to coreboot
via HOBs returned from fsp_memory_init().
* AGESA currently sets up MTRRs, as in most older generations.
Take ownership back immediately before running ramstage.
* Remove cbmem initialization, as the FSP driver handles this.
* Add chipset_handle_reset() for compatibility.
* Top of memory is determined by the FSP driver checking the HOBs
passed from AGESA. Note that relying on the TOM register happens
to be misleading when UMA is below 4GB.
BUG=b:147042464
TEST=Boot trembyle to payload
Change-Id: Iecb3a3f2599a8ccbc168b1d26a0271f51b71dcf0
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34423
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FSP AGESA overrides the MTRRs that coreboot set up. Until this is fixed
we need to save and restore the MTRRs to undo what AGESA did.
Once AGESA is fixed, we can delete these files.
BUG=b:155426691, b:147042464
TEST=Boot trembyle and see MTRRs being modified
Saving Variable MTRR 0: Base: 0x00000000 0xff000005, Mask: 0x0000ffff 0xff000800
Saving Variable MTRR 1: Base: 0x00000000 0x08070006, Mask: 0x0000ffff 0xffff0800
Saving Variable MTRR 2: Base: 0x00000000 0x00000000, Mask: 0x00000000 0x00000000
Saving Variable MTRR 3: Base: 0x00000000 0x00000000, Mask: 0x00000000 0x00000000
Saving Variable MTRR 4: Base: 0x00000000 0x00000000, Mask: 0x00000000 0x00000000
Saving Variable MTRR 5: Base: 0x00000000 0x00000000, Mask: 0x00000000 0x00000000
Saving Variable MTRR 6: Base: 0x00000000 0x00000000, Mask: 0x00000000 0x00000000
Saving Variable MTRR 7: Base: 0x00000000 0x00000000, Mask: 0x00000000 0x00000000
Saving Fixed MTRR 0: 0x00000000 0x00000000
Saving Fixed MTRR 1: 0x00000000 0x00000000
Saving Fixed MTRR 2: 0x00000000 0x00000000
Saving Fixed MTRR 3: 0x00000000 0x00000000
Saving Fixed MTRR 4: 0x00000000 0x00000000
Saving Fixed MTRR 5: 0x00000000 0x00000000
Saving Fixed MTRR 6: 0x00000000 0x00000000
Saving Fixed MTRR 7: 0x00000000 0x00000000
Saving Fixed MTRR 8: 0x00000000 0x00000000
Saving Fixed MTRR 9: 0x00000000 0x00000000
Saving Fixed MTRR 10: 0x00000000 0x00000000
Saving Default Type MTRR: 0x00000000 0x00000800
Saving SYS_CFG: 0x00000000 0x00000800
...
MSR 0x200 was modified: 0x00000000 0x00000006
MSR 0x201 was modified: 0x0000ffff 0x80000800
MSR 0x202 was modified: 0x00000000 0x80000006
MSR 0x203 was modified: 0x0000ffff 0xc0000800
MSR 0x204 was modified: 0x00000000 0xc0000006
MSR 0x205 was modified: 0x0000ffff 0xf0000800
MSR 0x250 was modified: 0x06060606 0x06060606
MSR 0x258 was modified: 0x06060606 0x06060606
SYS_CFG was modified: 0x00000000 0x00740000
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6048b25bd8a32904031ca23953f9726754b5a294
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40922
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Perform the P2SB hide/unhide trick. This is needed so that BAR0
(0xfd000000) is not reclaimed by resource allocator, since it can
not deal with a device that does not exist (hidden).
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I5db0ae4e31d72ba86efba5728b2afc68d3180d5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
Use common P2SB driver. This is needed to address a problem when
enumerator does not see p2sb device (since it is hidden) but it
is active and BAR is decoded.
Change-Id: I9cb821a5684f15f1e1486872bf806a6ee3d0676f
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40920
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add p2sb.h that is shared by all currently supported Xeon SP CPUs.
Change-Id: Idcbff7ad587cb116897a953c079fb0a8b86cc2ed
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40919
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable P2SB in static device tree so that hide/unhide trick
works.
Change-Id: I7dc20b001605b715155d333a07580e21a5f24136
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
These parameters were found to work fine for 2-socket configuration,
for FSP based on tag 16.D.21.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I466a7f2951ef307036ddaed0be0aacf98dd2710f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
It is necessary to rename the file gpio.h so that there are no conflict
with another file (src/include/gpio.h)
Change-Id: I4e3ef5882d6cb0ddbcb8357b54106ff2f47e4c51
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40733
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I8599dca99c1f34e3937c5b77b3505815ce625b46
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
If the current pad configuration can not be defined using standard
macros from the gpio_defs.h [1], then the intelp2m utility generates
"advanced" _PAD_CFG_STRUCT() macros. However, often this configuration
in the vendor’s firmware is erroneous. Change the extended macros to
standard ones taking into account the information based on the schematic
diagram and the previous GPIO configuration for FSP-M [2].
[1] src/soc/intel/common/block/include/intelblocks/gpio_defs.h
[2] src/mainboard/ocp/tiogapass/skxsp_tp_gpio.h
Change-Id: I56e45b1df77acbdd67e6325c3745a7ad137f8805
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
|
|
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1
registers values from the inteltool dump, is more understandable and
makes the code much cleaner. The gpio.h file with PAD_CFG macros was
automatically generated using the util/intelp2m [1] utility:
./intelp2m -p lbg -file tiogapass/vendorbios/inteltool_gpio.log
According to the documentation [2], the Host Software Pad Ownership
register only affects the pads that are configured as input (GPI).
The intelp2m utility takes this into account when converting macros
and ignores bits from this register for the corresponding pads.
[1] https://review.coreboot.org/c/coreboot/+/35643
[2] Intel Document Number: 549921
Change-Id: I21e98721e58b00be9196927837daa2b5d2560822
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40731
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to changes in the soc/xeon_sp code [1,2], server motherboards
with Lewisburg PCH can use the soc/intel/common/gpio driver to configure
GPIO controller. This patch adds pads configuration map, which has the
format required by the GPIO driver. The data for this was taken from the
inteltool register dump with AMI firmware. The gpio.h file with pad
configuration was generated automatically using the util/intelp2m [3]:
./intelp2m -raw -p lbg -file tiogapass/vendorbios/inteltool_gpio.log
[1] https: //review.coreboot.org/c/coreboot/+/39425
[2] https: //review.coreboot.org/c/coreboot/+/39428
[3] https: //review.coreboot.org/c/coreboot/+/35643
Change-Id: I818d040fa33f3e7b94b73c9bbbafca5df424616d
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39427
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since CPX FSP headers are not released yet, populate certain
settings with hard-coded offsets. Provided values are probably
not correct and I do not understand what they mean and there is
no documentation available yet. However they were found to work
to a certain degree.
TEST=tested on OCP Sonora Pass EVT
Change-Id: I0f78cde69cb8a49a388a412b97bf8713e5b380ea
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40554
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9b15b5458bb8140fa9bb6b0ffb6b9c78e8d8a93b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Just a minimal set of board files needed to get it to boot
in 1 CPU mode.
Signed-off-by: Ryback Hung <ryback.hung%quantatw.com@gtempaccount.com>
Change-Id: Ia7b45c78b38d091bd9535899b681746e13efb4fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
|
|
Change-Id: I353daf35c843521b089ff8411a9ba8c801605ff9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ie213b8c08e2d2b33a1dc1fda632163160d1cd70e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: If7e2c84c39039e0dc6811f247390f856fc634b33
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I09cc69a20dc67c0f48b35bfd2afeaba9e2ee5064
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I0fd1a758d8838b3eea5640b41eee6a6893360aa3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The AMD64 Architecture Programmer's Manual, Volume 2: Systems
Programming says the following about variable MTRRs:
Variable Range Size and Alignment.
The size and alignment of variable memory-ranges (MTRRs) and I/O ranges
(IORRs) are restricted as follows:
* The boundary on which a variable range is aligned must be equal to the
range size. For example, a memory range of 16 Mbytes must be aligned on a
16-Mbyte boundary (i.e., naturally aligned).
* The range size must be a power of 2 (2^n , 52 > n > 11), with a minimum
allowable size of 4 Kbytes. For example, 4 Mbytes and 8 Mbytes are
allowable memory range sizes, but 6 Mbytes is not allowable.
Print out errors if these conditions are violated. I didn't assert since
`set_var_mtrr` can be used in boot block before the serial console is
enabled.
BUG=b:147042464
TEST=Boot trembyle and see MTRR errors:
MTRR Error: base 0xcc800000 must be aligned to size 0x1000000
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8b8c734c7599bd89cf9f212ed43c2dd5b2c8ba7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40762
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Let's gather some documentation ideas for the season of docs. I reused
the project ideas style (thanks Patrick). Feel free to add yourself as a
mentor here. Also if you have more ideas, please add them to the
document.
Change-Id: I72221cbd53b99cdc946109753cf72af9c865a1e5
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40662
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I11b8743234cb1292db8c930edecf8fb5c47d63fd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add GPIO_PCH_WP (GPP_C11) to associate GPP_PCH_WP with community
zero.
TEST=Build coreboot, flash, boot to
and log into kernel, execute "wp enable" in console,
execute "crossystem" at kernel prompt and verify that "wpsw_cur"
shows as being "1", Execute "wp disable" in console, execute
"crossystem" at kernel prompt and verify "wpsw_cur" is 0.
Change-Id: Ie4ae1365a7611b8be3e795798c171e3f7ea9e417
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40744
Reviewed-by: Usha P <usha.p@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:153642124
TEST=Saw I2C communication
Change-Id: I31f8b97d1ff7b687d7e078d5b594d1ad73c815e7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2145457
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
sb_reset_i2c_slaves is called in fch_pre_init.
BUG=b:153675916
TEST=Builds on trembyle
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I157e473984257d633ceb3ef9df45c71a31c5c00b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
fch_early_init already calls i2c_soc_early_init().
BUG=b:153675916
TEST=Boot trembyle and only see 1 i2c initialization message
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I689616fb617904df1781be3abe9d1dc580608173
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Mainboards must provide their DDI descriptors.
BUG=b:153502861
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2146443
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2146439
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2146438
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2145453
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2145454
Change-Id: Ib3f115711e74d0e6eb5b063b3dccb36b265779af
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40875
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The expected error code observed in clear_pending_events() should
be EC_RES_UNAVAILABLE(9), not EC_RES_INVALID_COMMAND(1).
BUG=b:153896701
Change-Id: I609490ceef675267760d34b5e9775211da93347c
Signed-off-by: Victor Ding <victording@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40900
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Harrison Peak (HrP) 9560 module needs a reset pin for BT power sequence.
BUG=b:155248677
TEST=Boot into OS and check BT is functional.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I55ed1b095ba53c414c44088f4a6e7720b970e2f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
understanding
BIT 1 -> DEBUG_INTERFACE_UART_8250IO
BIT 4 -> DEBUG_INTERFACE_LPSS_SERIAL_IO
Change-Id: I566b9dc82b2289af42e58705ebeee51179886f1f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Update USB3 ports configuration as schematics design.
BUG=b:155026295
TEST=Boot into OS and check WWAN device detected by lsusb.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Icb938e5a9c05fcc9772219b081a6f05334261baf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40818
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
An array of 64bit integers is passed to acpi_dp_add_integer_array() but
it is not const so can't take a const array without a compiler error.
The function does not modify the array so it can be made const without
breaking anything and allowing a const array to be passed in the future.
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I98ecdaef5ddfa2026390e2812f5ea841ee51f073
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40882
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The generic container HID is defined in ACPI specification as PNP0A05.
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I3632e77533a47f22b92259b469b03e63f51687e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently if a child table is created and added to a property list
without adding any properties to that child it will generate an
empty package. For example:
struct acpi_dp *dsd = acpi_dp_new_table("_DSD");
struct acpi_dp *prop = acpi_dp_new_table("PROP");
acpi_dp_add_child(dsd, "dsd-prop", prop);
acpi_dp_write(dsd);
Results in an empty PROP package:
Name (_DSD, Package (2)
{
ToUUID("dbb8e3e6-5886-4ba6-8795-1319f52a966b")
Package (1) {
Package (2) {
"dsd-prop",
"PROP"
}
}
}
Name (PROP, Package (0)
{
}
Empty packages don't seem to be explicitly forbidden, but they don't
serve a purpose with device properties. Instead, if packages without
any properties or children are skipped then this empty package is not
written and the added child property can refer to another property that
is already defined.
This allows creating property references to existing tables, which can
save duplication and namespace collision issues with nested properties.
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I9fee2ceb8a4496b90c7210533eee8c2b186cdfff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:152019429
BRANCH=None
TEST=1. provision dram_part_num field of CBI
2. modify mainboard - dedede to report DRAM part number from CBI
3. check DRAM part number is correct in SMBIOS for memory device
Change-Id: I509d06a81bd005c5afe6e74a2da2ca408dee7b29
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Separate specific setting to variant from baseboard.
baseboard/romstage.c in current release is only utilized by
careena, we could remove it from the rest of variant build.
BUG=b:154357210,b:154848243
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I658526e44aadc47bdc5538f506a1bfe2e5f20f63
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix FSP CAR on platforms that have ROM_SIZE of 32MiB.
CodeRegionSize must be smaller than or equal to 16MiB
to not overlap with LAPIC or the CAR area at 0xfef00000.
Tested on Intel CFL, the new code allows to boot using FSP-T.
Change-Id: I4dfee230c3cc883fad0cb92977c8f5570e1a927c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Fix code blocks, add a newline, use inline code blocks for commands.
Change-Id: Iecf04b00ed12323c124517f2557cc8b60640b618
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
LTE module is lost after idle overnight, with this workaround,
host will not initiate U3 wakeup at the same time with device,
which will avoid the race condition.
Disable XHCI LFPS power management.
If the option is set in the devicetree, the bits[7:4] in
XHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated
from default 9 to 0.
BUG=b:146768983
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ib8e5ae79e097debf0c75ead232ddbb2baced2a2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Enable Goodix touch screen and ensure it works properly.
BUG=b:154191288
TEST=FW_NAME=malefor emerge-volteer coreboot chromeos-bootimage
Boot to kernel and check the Goodix touch screen function.
Signed-off-by: William Wei <wenxu.wei@bitland.corp-partner.google.com>
Change-Id: I236ac56dd0a1817092151bae93e699115ba88e4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40598
Reviewed-by: Alex Levin <levinale@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Running commit aee0baf0690681fae85d24e6887d6cbb9209de83 on
Facebook fbg1701 results in an error:
VB2:vb2_rsa_verify_digest() ERROR - vboot2 work buffer too small!
ERROR: HASH table verification failed!
The actual vboot structures require more space.
Workbuffer size needs to be increased.
We didn't determine the commit causing the issue because this change
fixes the issue.
BUG=N/A
TEST=Build and boot Facebook fbg1701
Change-Id: I5caebc643eb493f4285c2f2fc164ff3a5d35e24e
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
|
|
Add unit test for src/device/i2c.c module.
This patch is also used as an example for incorporating Cmocka mocking
feature (-wrap linker flag).
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: I2eeb565aacc724ae3b9f5c76ef4b98ef695416d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Show a basic example of how unit testing can be applied for the coreboot
project. Add a test harness for lib/string.c module.
TEST=Install cmocka via appropriate command:
sudo apt-get install -y libcmocka-dev
sudo emerge dev-util/cmocka
yum install libcmocka-devel
* Build and run unit tests via `make unit-tests`
* Check the output to see that tests passed.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: Ibf5554d1e99a393721a66bdd35af0122c2e412c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Add a subsystem which will be used for writing, building and running
unit tests for different coreboot's modules. This work is built using
Cmocka unit testing framework. Description of what unit testing means
(for the author) and how unit testing framework evaluation was performed
may be found in Documentation/technotes/2020-03-unit-testing-coreboot.md
Makefiles structure is very similar to this used for building coreboot
images. Every directory has its own Makefile.inc were tests' names,
sources, subdirs and multiple other test-related attributes are defined
in form of variables.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: I9b0220b84b9a6e448476ca3eb3ccccc5fb829ad1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: I552d6c3373219978b8e5fd4304f993d920425431
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
BUG=none
TEST=Made sure trembyle builds
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9df70fd5c41a9a68edc7be3c2e920c4dc94d5af9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40871
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enables ACPI backlight controls.
Change-Id: Iccf50f427b7555ee1a3ef9cc11a89d532789ac54
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Unlike prior AMD devices, picasso cannot rely on the cache-as-RAM
setup code to properly enable MTRRs. Add that capability to the
bootblock_c_entry() function. In addition, enable an MTRR to cache
(WP) the flash boot device and another for WB of the non-XIP bootblock
running in DRAM.
BUG=b:147042464
TEST=Boot trembyle to payload and make sure bootblock isn't abnormally
slow.
Change-Id: I5615ff60ca196e622a939b46276a4a0940076ebe
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38691
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Error codes are renamed as follows:
VBERROR_SHUTDOWN_REQUESTED
--> VB2_REQUEST_SHUTDOWN
VBERROR_REBOOT_REQUIRED
--> VB2_REQUEST_REBOOT
VBERROR_EC_REBOOT_TO_SWITCH_RW
--> VB2_REQUEST_REBOOT_EC_SWITCH_RW
VBERROR_EC_REBOOT_TO_RO_REQUIRED
--> VB2_REQUEST_REBOOT_EC_TO_RO
BRANCH=none
BUG=b:124141368, chromium:988410
TEST=emerge-nami coreboot
Cq-Depend: chromium:2143030
Change-Id: Id82cf85f49dfb63a9c3d41aacd3969786bffcac7
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40749
Reviewed-by: Joel Kitching <kitching@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updating from commit id 55154620:
vboot: Add screens for recovery using disk
to commit id 3aab3014:
vboot: Convert reboot-related errors to vboot2-style
This brings in 3 new commits.
Change-Id: I75be535e0b0f8080366b98e5ae2007452ad51738
Signed-off-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40845
Reviewed-by: Joel Kitching <kitching@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This CL adds support to fill PcieRpClkReqDetect UPD from devicetree.
Filling this UPD will allow FSP to enable proper clksrc gpio
configuration.
BUG=None
BRANCH=None
TEST=Build and boot tglrvp.
Change-Id: Iad0ba94fea019623a5b98fff0cb4a2cd1d2a7bd7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This patch adds psys_pmax calculation. There are two types of power
sources. One is barrel jack and the other is USB TYPE-C. The voltage
level is fixed for a barrel jack while TYPE-C may vary depending
on power ratings. We need to get voltage information from
EC and calculate correct psys_pmax value. The psys_pmax needs to be
set before FSP-S since FSP-S will handle the setting passing to pcode,
so move the routine ahead to variant_ramstage_init.
BUG=b:151972149
TEST=emerge-puff coreboot chromeos-bootimage
check firmware log and ensure psys_pmax is passed to FSP
check the data from dump_intel_rapl_consumption in the OS and
ensure the power data is close to an external power meter.
Change-Id: Iff767d4b44a01e766258345545438a54a16d1af5
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Change-Id: I34facbe0cbbdc91066799b586d96abca1599c509
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40743
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib403f5a231f86bdc60b956e72a4ae631aa6a3899
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Support USB Chicony user facing camera.
BUG=b:155109736
BRANCH=None
TEST=Build and Boot waddledoo board and able to capture image
using user facing camera.
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I7580a58086977e239dca49c1def4f03583831662
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: If39cdfb21fec307141593f2482e014e146d4f1f2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I5a07a00e1183ef834d97c11268935617cfe17faa
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I81b740e0cfcf0e1bf096427b45ffba06d357fee6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I212ef304a03d068232f50a71c318e2b468336339
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3a00db217ce7acd11f979e64bb5d417a8bfc8717
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I7b39e895501c3bc672a9dffec06b7969dc2f911f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This CL selects the PcieRpClkReqDetect for the required root ports
which is needed to allow proper clksrc gpio configuration.
Also, sets the unused PcieClkSrcUsage to 0xFF.
BUG=None
BRANCH=None
TEST=Build and boot jslrvp with NVMe
Change-Id: Ie4ae1365a7621b8be3b795798c171e3f7ea9e487
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
This CL adds support to fill PcieRpClkReqDetect UPD from devicetree.
Filling this UPD will allow FSP to enable proper clksrc gpio
configuration.
BUG=None
BRANCH=None
TEST=Build and boot jslrvp with NVMe
Change-Id: Iad0b394fea019223a5b98fff0cb4a2bd1d2a7bd7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40757
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
|
|
Change-Id: I12345a5b6c9ce94ca9f8b555154b2278a8ff97bf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
smbios_slot_{type,data_width,length,designation} used for smbios_type_9 needs "smbios.h"
Also use already defined 'smbios_type11' in "smbios.h".
This will also include <smbios.h> in "static.c" file, this we can remove indirect includes of
<smbios.h> in "chip.h"
Change-Id: Id412a504da2fd75648636febd150356569e07935
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40310
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The stuffed resistor straps are weaker compared to the internal pull-up.
This can cause the GPIO to read '1' always. Remove the internal pull-up.
Also read the GPIO only on the boards where the board version is
populated.
BUG=b:154301008
TEST=Build and boot the mainboard.
Change-Id: Ib640211b9f50dfb0174a570eda1625bacbebb855
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update DPTF settings for smooth fan speed control.
BRANCH=firmware-hatch-12672.B
BUG=b:154074920
TEST=Built and test on Helios system
Change-Id: I3f4d9fd9e17541dd5fb7982a8b43a039c41cba87
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40530
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=None
BRANCH=None
TEST=Build and Boot waddledoo board and able to capture image
using world facing camera.
Change-Id: I51dcf96a82535fc1e0b9247fd52af919885575e5
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
1. Add support as per the schematics
2. Add 2 Ports and 2 Endpoints
3. Add support for OTVI8856 and OTVI5676
4. Add ON and OFF logic as Power Rails are same for both sensor
BUG=None
BRANCH=None
TEST=Build and Boot waddledoo board and able to capture image
using world facing camera.
Change-Id: Ic8687bce4896d9fc17b2190b8d11618af3515cc1
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: I62a213013d9008d8a4a22b5908b7fc7d1b663c4b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The QEMU XHCI driver does not implement the Port Change Detect bit
in the USBSTS register. As a result no devices are attached without
looking at each port individually.
Detect this as a quirk based on the QEMU XHCI controller PCI ID,
and apply it to the root hub quirk list so it can get used by the
generic hub driver to skip this check.
With this change an attached USB mass storage device is detected and
able to boot when supplied to qemu:
-drive if=none,id=usbmsc,format=raw,file=/tmp/disk.img
-device qemu-xhci,id-xhci
-device usb-storage,bus=xhci.0,drive=usbmsc
Change-Id: I6689cb1dbb24c93d45f5c5ef040b713925d07588
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39839
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I2bf1eb87bb5476dd77b5a56dfe8846e82d414523
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40666
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add initial support for wheelie variant board.
BUG=b:154664137
BRANCH=None
TEST=build
Change-Id: Id638e987f45c247dae824f221a38ccf32626572f
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update usb2 port strength parameter for usb2_port[0] to improve SI.
BUG=b:154668734
BRANCH=firmware-hatch-12672.B
TEST=Built and checked SI margin of USB2 ports
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: I8b4b58a67dc0835a677770a2968e8d8d61e0374f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add support to generate ACPI operations to get/set/clear RX/TX GPIOs.
BUG=b:152936541
TEST=Build and boot the mainboard. Ensure that there are no errors in
the coreboot logs regarding unsupported ACPI GPIO operations.
Change-Id: Ibc4846fbd9baf4f22c48c82acefed960669ed7d4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update UPD IIO bifurcation at run-time according to different Riser
cards. For detail please reference
Facebook Server Intel Motherboard v4.0, Sec. 10.1.2 Riser card types.
With the engineering build FSP, it can only configure IIO for
one socket so my local test needs to remove all socket1 elements
from tp_iio_bifur_table.
This change relies on [1] and need to add GPP_C15 and GPP_C16 to
early_gpio_table for gpio configuration in bootblock.
[1] https://review.coreboot.org/c/coreboot/+/39427/
Tested=OCP Tioga Pass can see socket0 IIO being updated with
an engineering build FSP.
Change-Id: I8e63a233a2235cd45b14b20542e6efab3de17899
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1
registers values from the inteltool dump, is more understandable and
makes the code much cleaner. The gpio.h file with PAD_CFG macros was
automatically generated using the util/intelp2m [1] utility:
./intelp2m -p lbg -file cedarisland/vendorbios/inteltool_gpio.log
According to the documentation [2], the Host Software Pad Ownership
register only affects the pads that are configured as input. The
intelp2m utility takes this into account when converting macros and
ignores bits from this register for the corresponding pads.
[1] https://review.coreboot.org/c/coreboot/+/35643
[2] Intel Document Number: 549921
Change-Id: Id671a9021a8313d8c3359b89c2934b929bcab1a4
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40736
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We should be sure that after romstage the pads will be configured
according to the config from gpio.h only. This patch sets the GPIO
configuration from gpio.h using the soc/intel/common/gpio.c driver
again in ramstage.
[1] https://review.coreboot.org/c/coreboot/+/40730
Change-Id: Ic49e504d96fe4fd44434e7b981f8d8d9e76880ef
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
|
|
According to changes in the soc/xeon_sp code [1,2], server motherboards
with Lewisburg PCH can use the soc/intel/common/gpio driver to configure
GPIO controller. This patch adds pads configuration map, which has the
format required by the GPIO driver. The data for this was taken from the
inteltool register dump with vendors firmware. The gpio.h file with pad
configuration was generated automatically using the util/intelp2m [3]:
./intelp2m -raw -p lbg -file cedarisland/vendorbios/inteltool_gpio.log
[1] https: //review.coreboot.org/c/coreboot/+/39425
[2] https: //review.coreboot.org/c/coreboot/+/39428
[3] https: //review.coreboot.org/c/coreboot/+/35643
Change-Id: I90b91e6dbf8c65c747d0e0d94c61023e610f93ab
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
|
|
-n needs to check against a string, but if CONFIG_TIANOCORE_BOOTSPLASH_FILE
is unset, then $(CONFIG_TIANOCORE_BOOTSPLASH_FILE) evaluates to nothing
and the check fails, leading the Makefile to try and copy a non-
existant file/path.
Change-Id: Iff717dd48748cff16f485bafaa91c7a225fb5bdb
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Most payloads, like GRUB, SeaBIOS and Linux, are able to initialize the
PS/2 keyboard themselves, so coreboot does not need to initialize it.
Therefore, this option should not be hard-coded for the mainboard, and
be left for the user to select.
Change-Id: Ibfb7efa22c525e60399afc198af6632330faaac3
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Since commit 6aa8c5bc (drivers/pc80: Do not initialize PS2 keyboard by
default), the Kconfig option `DRIVERS_PS2_KEYBOARD` already defaults to
`n`. So, remove it here, as this option should be user selectable
anyway depending on the payload.
Change-Id: I3d08fb6bbb3e9d53fd2fed96f26679e8b1e73f8c
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Most payloads, like GRUB, SeaBIOS and Linux, are able to initialize the
PS/2 keyboard themselves, so coreboot does not need to initialize it.
Therefore, this option should not be hard-coded for the mainboard, and
be left for the user to select.
Change-Id: Iac835d2e7a3232f8e5c76f10984ae3f172f9c0ca
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change enables support for em100 for Picasso platform. Since
em100 requires lower SPI speed, this change configures speed in all
modes as 16MHz.
BUG=b:147758054,b:153675510
BRANCH=trembyle-bringup
TEST=Verified that em100 works fine on trembyle.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib5ea1fe094fda9b8dba63e94b37e61791629564f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40825
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds options to allow mainboard to configure SPI speed for
different modes as well as the SPI read mode.
BUG=b:153675510,b:147758054
BRANCH=trembyle-bringup
TEST=Verified that SPI settings are configured correctly for trembyle.
Change-Id: I24c27ec39101c7c07bedc27056f690cf2cc54951
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Rob Barnes <robbarnes@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40421
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds a helper sb_spi_init() that makes all the required
calls for configuring SPI to ROM.
BUG=b:147758054,b:153675510
BRANCH=trembyle-bringup
TEST=Verified that SPI configuration is correct for trembyle.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic5b395a8d3bdab449c24b05d1b6b8777e128b5e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40824
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds enums for spi_read_mode and spi100_speed in
preparation for adding these to chip.h in follow-up CLs. This makes it
easier to reference what the mainboard is expected to set for these
SPI configs.
BUG=b:147758054,b:153675510
BRANCH=trembyle-bringup
TEST=Verified that SPI configuration is correct for trembyle.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7f9778b41bd059a50f20993415ebd8702a1ad58e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40823
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
southbridge.h does not really need chip.h. So, this change removes the
inclusion of chip.h from it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I09c87b975ecd5f7798da8dd858be0c729aef42de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40822
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
sm.c requires acpimmio_map.h for ACPIMMIO_* macros. This change
includes acpimmio_map.h in sm.c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ia049254fa389a76bcf6538c0449229b4d856086e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40821
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 285975dbba8c7f3bbb9f9950e79a30bb983d5123.
Reason for revert: VB2_RECOVERY_TRAIN_AND_REBOOT was never meant to have
any special effect on memory training behavior. It was just supposed to
be a "reboot automatically after reaching kernel verification" recovery
reason. On x86 devices this was used to prime the separate recovery
MRC cache in the factory (make sure it is initialized before shipping).
This isn't used on Kukui anyway, but in order to make sure nobody copies
this code and keep the behavior consistent between platforms, let's
remove it.
Change-Id: I5df5e00526e90cb573131de3c8bac9f85f4e3a5f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40623
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable aspeed's function that port 80h direct to GPIO for LED display,
refer to section 9.4 Port 80h Direct to GPIO Guide of aspeed's
Application Design Guide, also configure GPIO to UART for output
serial console messages.
Tested=Check if port 80h LED debug card can display POST codes at
early stage, and serial console can see the related messages.
Change-Id: I087d5a81b881533b4550c193e4e9720a134fb8e7
Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40481
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:152893285
BRANCH=none
TEST=Build and boot to OS volteer with Intel SATA and reboot
from OS console
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ibed8f8c445bf2ac2290ffb670d8dfb83fc960438
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Create the trondo variant of the volteer reference board by copying the
template files to a new directory named for the variant.
BUG=b:154678884
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_TRONDO
Change-Id: Ie4f9bfe4798e14f91c6cb439f5c5ab2b9ea52b51
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40686
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ia25d4ce9260fa8c00fdea0e19f5e927559371af0
Signed-off-by: Felix Singer <migy@darmstadt.ccc.de>
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Based on USB SI report to fine tune the strength for USB2 port0.
BRANCH=none
BUG=b:153590143
TEST=build and test USB2 port0 function works fine.
Change-Id: I070c9e1c8153a680fb8f827889738a764d7ea9f4
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40482
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
memcpy() is meant to be used on normal memory and often implemented with
architecture-specific optimizations to make that as performant as
possible. MMIO registers often have special access restrictions that may
be incompatible with whatever memcpy() does. For example, on arm64 it
uses the LDP (load pair) to load 16 bytes at a time, which makes 4-byte
MMIO registers unhappy.
This patch removes the caching of the XHCI capreg registers and changes
it back to a pointer. The CAP_GET() macro is still accessing a full
(non-bitfield) uint32_t at the end so this should still generate a
4-byte access (which was the goal of the original change in CB:39838).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id058c8813087a8e8cb85f570399e07fb8a597108
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
It seems that all SC7180 boards we have can well handle 37.5MHz of SPI
flash speed, so bump that up from the current 25MHz so that we don't
leave boot speed on the table. (The next step would be 50MHz which
currently doesn't work on all boards so we're not going there yet.)
BUG=b:117440651
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id6e98fcbc89f5f3bfa408c7e8bbc90b4c92ceeea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
Check SPD is not NULL before print. This can prevent the system
from hanging up.
BUG=b:154445630
TEST=Check NULL SPD is not print.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Iccd9fce99eda7ae2b8fb1b4f3c2e635c2a428f04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40560
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Looks like 5 is a valid system type, as Google Beltino and Slippy are
using it. According to comments on these mainboards' code, this value
corresponds to ULT systems. So, add it to the comment on the pei_data
struct, which was likely copied from Sandy Bridge and was not updated.
Change-Id: I3654bb6022839dba3e1499cf43e8beaa97d1def1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
