summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-10-08google/gru: Add USB 2.0 PHY tuning for Kevin PHY0 and PHY1William wu
We found that Kevin board PHY0 and PHY1 eye-diagram margin is not enough to make compliance test pass, and the PHY0 USB SI is worse than PHY1, because of the higher PCB impedance. For PHY0, we can't improve the eye-diagram by SW PHY tuning, so we need to reduce the RBIAS resistance from 133 ohm to 115 ohm, it can help to increase the eye-height. For PHY1, we can improve the eye-diagram by setting the max pre-emphasis level. And after the above change, the USB2 signal amplitude will become larger at the test point near to SOC USB2 PHY, in order to avoid mis-trigger the disconnect detection (650mV), we need to disable pre-emphasize in eop state. BRANCH=None BUG=chrome-os-partner:53863 TEST=do USB 2.0 compliance test for Kevin C0 and C1 port. Change-Id: I95c0acd79623aeca9a0ae077b1dd3836d91fe561 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: de3cdef128966d76e7d8e2ebd641763b911c3ad5 Original-Change-Id: I00cb325b9938e4276cc77b5d6f5faa7023379608 Original-Signed-off-by: William wu <wulf@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/390615 Original-Commit-Ready: Julius Werner <jwerner@chromium.org> Original-Tested-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16911 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-08rockchip/rk3399: Add Type-C PHY initWilliam wu
Though we don't use Type-C PHY to support USB3 in firmware, we still need to initialize the Type-C PHY, and make sure the power state of pipe is always fixed to U2/P2. After this, we can force USB3 controller to work in USB2 only mode. BRANCH=none BUG=chrome-os-partner:56425 TEST=Go to recovery mode, plug a Type-C USB drive containing chrome OS image into both ports in all orientations, check if system can boot from USB. Change-Id: I95bb96ff27d4fecafb7b2b9e9dc2839b5c132654 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 8ec98507845276119d8a9d5626934dedcb35f2dd Original-Change-Id: Ie3654cd1c1cb76b62aa9b247879b60cbecee0155 Original-Signed-off-by: William wu <wulf@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/391412 Original-Commit-Ready: Julius Werner <jwerner@chromium.org> Original-Tested-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16910 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-08RISCV: have the make-spike-elf.sh script use the riscv toolsRonald G. Minnich
We do this so that the riscv objdump can be used on the coreboot.elf file. Change-Id: Ib8bf85a3299dd75b779e7fa3757f5b62c9c7170b Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-on: https://review.coreboot.org/16918 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
2016-10-07soc/intel/apollolake: Disable HECI2 device reset on S3 resumeAndrey Petrov
Converged Security Engine (CSE) has a secure variable storage feature. However, this storage is expected to be reset during S3 resume flow. Since coreboot does not use secure storage feature, disable HECI2 reset request. This saves appr. 130ms of resume time. BUG=chrome-os-partner:56941 BRANCH=none TEST=powerd_dbus_suspend; resume; check time with cbmem -t. Note FspMemoryInit time is not significantly different from normal boot time case. Change-Id: I485a980369c6bd97c43b9e554d65ee89e84d8233 Signed-off-by: Andrey Petrov <andrey.petrov@intel.com> Reviewed-on: https://review.coreboot.org/16870 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-07vendorcode/intel/fsp: Update UPD headers for FSP 157_10Brandon Breitenstein
These header files contain a few new UPDs. The EnableS3Heci2 UPD will be used to save ~100ms from the S3 resume time on Apollolake chrome platforms. BUG=chrome-os-partner:58121 BRANCH=none TEST=built coreboot for reef and verified no regressions Change-Id: I1f324d00237c7150697800258a2f7b7eed856417 Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com> Reviewed-on: https://review.coreboot.org/16869 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07google/reef/variants/pyro: Add support for GPIO output polarityMartin Roth
commit 028200f7 - x86/acpi_device: Add support for GPIO output polarity updated ACPI_GPIO_OUTPUT to ACPI_GPIO_OUTPUT_ACTIVE_HIGH for the other boards that needed it, but pyro wasn't in the tree when it was initially pushed. Now that pyro is in the tree, it needs to be updated as well. Change-Id: I617999b06ee584e0543d7ae3232bb2be2ff7429c Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16930 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins)
2016-10-07util/release/build-release: Update tar commandMartin Roth
Between GNU Tar 1.28 & 1.29, the files excluded by --exclude-vcs was updated. This breaks the reproducibility. Instead, just manually exclude the files to match what was excluded in v 1.28 and earlier. Change-Id: Ie0717891506f4a6d750ff264f9cc2494a296265b Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16900 Tested-by: build bot (Jenkins) Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2016-10-07util/release/build-release: Update scriptMartin Roth
- Add more help text. - Remove braces from variables where the variable is isolated. - Remove --recurse-submodules from clone. This breaks on old coreboot versions. - Add some whitespace between blocks. - Fix all shellcheck warnings. - Verify tar version and fail if it doesn't support --sort. Change-Id: I4a49df99532d9a92a4a05bceff16f96a4fc3e205 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16883 Tested-by: build bot (Jenkins) Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2016-10-07soc/intel/apollolake: Implement stage cache to improve resume timeBrandon Breitenstein
This patch enables stage cache to save ~40ms during S3 resume. It saves ramstage in the stage cache and restores it on resume so that ramstage does not have to reinitialize during the resume flow. Stage cache functionality is added to postcar stage since ramstage is called from postcar. BUG=chrome-os-partner:56941 BRANCH=none TEST=built for Reef and tested ramstage being cached Change-Id: I1551fd0faca536bd8c8656f0a8ec7f900aae1f72 Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com> Reviewed-on: https://review.coreboot.org/16833 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-07src/southbridge: Remove unnecessary whitespaceElyes HAOUAS
Change-Id: Ibcac5dd60dc7da82bbeeb89ac445a5a1aa56ed3d Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16852 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07src/arch: Remove whitespace after sizeofElyes HAOUAS
Change-Id: Ia2fc3d5ea88d61ba7c4a1daebfe74a24948c8f6e Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16865 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07src/cpu: Remove unnecessary whitespaceElyes HAOUAS
Change-Id: I0903b7ca9eada4beacfcdbcacddec23c3515651e Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16850 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07src/southbridge: Remove whitespace after sizeofElyes HAOUAS
Change-Id: Ic3b599d49a4c03ad8035c558b975f31cb91d253b Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16862 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07cpu/amd/geode_gx2: Remove unnecessary semicolonElyes HAOUAS
Change-Id: I5585eac9fec5180254c7d3cc966441e9794e8390 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16858 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07src/drivers: Remove whitespace after memcpy & memsetElyes HAOUAS
Change-Id: If79eb706b6d44f7c34dfe31a1545f5850870b334 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16866 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07src/mainboard: Remove whitespace after sizeofElyes HAOUAS
Change-Id: Ie2a047d35e69182812c349daedc5b3b5fde20122 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16860 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07src/mainboard: Remove unnecessary whitespaceElyes HAOUAS
Change-Id: I35cb7e08d5233aa5a3dbb4631ab2ee4dc9596f98 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16849 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07x86/acpi_device: Add support for GPIO output polarityFurquan Shaikh
Instead of hard-coding the polarity of the GPIO to active high/low, accept it as a parameter in devicetree. This polarity can then be used while calling into acpi_dp_add_gpio to determine the active low status correctly. BUG=chrome-os-partner:55988 BRANCH=None TEST=Verified that correct polarity is set for reset-gpio on reef. Change-Id: I4aba4bb8bd61799962deaaa11307c0c5be112919 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/16877 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2016-10-07x86/acpi_device: Fix writing of array propertyFurquan Shaikh
Only acpi_dp of type DP_TYPE_TABLE is allowed to be an array. This DP_TYPE_TABLE does not have a value which is written. Thus, acpi_dp_write_array needs to start counting from the next element type in the array. Fix this by updating the initialization in for loop for writing array elements. BUG=chrome-os-partner:55988 BRANCH=None TEST=Verified that the correct number of elements are passed for add_gpio in maxim sdmode-gpio. Change-Id: I8e1e540d66086971de2edf0bb83494d3b1dbd176 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/16871 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-10-07ec/google/chromeec: Add minimum delay between SPI CS assertionsJulius Werner
Some Chrome OS ECs require a small amount of time after a SPI transaction to reset their controllers before they can service the next CS assertion. The kernel and depthcharge have always enforced a 200us minimum delay for this... coreboot should've done the same. BRANCH=gru BUG=chrome-os-partner:58046 TEST=Booted Kevin in recovery mode, confirmed that recovery events got logged with correct timestamps in eventlog. Change-Id: I32ec343f3293ac93729d3e6e2f43d7605a396cdb Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: b9e4696533d4318ae7c8715b71ab963d8897c16c Original-Change-Id: I6a7baf7859d5d50e299495d118e7890dcaa2c1b0 Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/392206 Original-Tested-by: Shawn N <shawnn@chromium.org> Original-Reviewed-by: Shawn N <shawnn@chromium.org> Reviewed-on: https://review.coreboot.org/16885 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07google/gru: drive WLAN_MODULE_RST# low as early as possibleBrian Norris
GPIO1_B3 (WLAN_MODULE_RST#) defaults as a pull-up input, but it is also "pulled up" by 1.8V_WLAN. However, 1.8V_WLAN remains low for some time during early boot. This leaves the signal floating somewhere in the middle. This has two potential issues: (1) we're leaking some power for some (hopefully) short period of time (2) we are possibly screwing with the Wifi power sequence; we aren't supposed to deassert PDn (i.e., MODULE_RST#) until all the rails have fully ramped for some period of time Neither of the above issues are likely to be significant, but it is nice to fix, I expect. BRANCH=gru BUG=chrome-os-partner:54026 TEST=measure WLAN_MODULE_RST# on scope at boot time Change-Id: Ia6af9ad6954ad8feeda33015e3f205842380939e Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 0e890a2787bf034d3358a33fc88c2dd8078593ab Original-Change-Id: I120e26ad0ca486a326874986e142dcaee965b62d Original-Signed-off-by: Brian Norris <briannorris@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/388009 Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16882 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07Revert "soc/intel/apollolake: Add pmc_ipc device support"Furquan Shaikh
This reverts commit 28821dbb2261267462a7e9b0cc1c23b51af2d3ee. (https://review.coreboot.org/16649) This change causes the kernel to boot really slow. Maybe there is an interrupt storm that prevents the kernel from making any progress. Reverting until the proper kernel dependency is met. BUG=chrome-os-partner:57364 BRANCH=None TEST=Kernels boots to prompt fine on DVT. Change-Id: I1c9913b4476a08303f9dd887b8631601c847dcf7 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: d7014ee1bb88df7a2d7f6b3dced797fef75b252d Original-Change-Id: I061c0b03b43b516a190b370c04888e73a410fcf1 Original-Signed-off-by: Furquan Shaikh <furquan@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/391233 Original-Reviewed-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/16881 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07soc/qualcomm/ipq40xx: Fix GPIO pull up config.Kan Yan
BUG=b:31690391 TEST=Tested with board ID BRANCH=none Change-Id: I9a2b7eec111a79827f72a506942a8ec833ba7e60 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: f23e2b6e72491aaafa15774f9bded3e14363abbc Original-Change-Id: I23183db29d7f7dd812e94ab6a1f2f1329c46ac60 Original-Signed-off-by: Kan Yan <kyan@google.com> Original-Reviewed-on: https://chromium-review.googlesource.com/388778 Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org> Original-Reviewed-by: Suresh Rajashekara <sureshraj@chromium.org> Reviewed-on: https://review.coreboot.org/16770 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07rockchip/rk3399: Actually remove big CPU initialization from bootblockJulius Werner
CL:377541 was supposed to remove the big CPU cluster initialization from rkclk_init() in the bootblock and move it to a more suitable place in ramstage. Except that next to all the code cleanup I did in that patch, I seem to have forgotten to actually remove that old code. Big thanks to Nico for spotting that in the upstream coreboot review. BRANCH=gru BUG=chrome-os-partner:54906 TEST=Booted Kevin. Change-Id: I09fe948b4587536802b42329b813177439e0804f Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 77f9eaf0446b22adfca79d0adf8a0ecfd93c0040 Original-Change-Id: I13dab208225b7e43ad864f2f3cf51b3c104acd4b Original-Reported-by: Nico Huber <nico.h@gmx.de> Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/389236 Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-on: https://review.coreboot.org/16769 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07rockchip/rk3399: select rank before triggering trainingDerek Basehore
This selects the rank to train before training is triggered. This is to prevent any race conditions with the hardware. BRANCH=none BUG=chrome-os-partner:56940 TEST=stressapptest -M 1536 -s 1000 Change-Id: I892bace414cf4495619d41bdaea0c4e91c1e29b3 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 8f2dd6f52978a9e54ddd2688eb68fd237aabfe2d Original-Change-Id: I4e7118d8509b59e391d0a254477b5390dfdd43a5 Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/387907 Original-Commit-Ready: Douglas Anderson <dianders@chromium.org> Original-Tested-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-by: 云平 汤 <typ@rock-chips.com> Reviewed-on: https://review.coreboot.org/16768 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07Gale: Fix the orange color to match the UX docSuresh Rajashekara
UX Doc = go/gale-hw-ui This color wasn't changed earlier as the change wasn't done in the OS also. However, since we cannot change this later in FW (but OS can change anytime), I am making this change after discussing with the UX team. BUG=b:31501528, b:31633562 TEST=Change the device state to 'recovery mode' to observe the new color. BRANCH=none Change-Id: Ia91f14eb77492095cb41a9de0bb9790e72aa4851 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 36a3d8c6eabbc0b23d0a15d5bddc5ed3bdeebe70 Original-Change-Id: I88768b94cf91804a6005e44b1a168e059698ec4b Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com> Original-Reviewed-on: https://chromium-review.googlesource.com/388206 Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org> Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org> Original-Reviewed-by: Christopher Book <cbook@chromium.org> Original-Reviewed-by: Kan Yan <kyan@google.com> Reviewed-on: https://review.coreboot.org/16767 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07rockchip/rk3399: Improve dram stability when run at high frequencyLin Huang
There are two modifications in the driver: 1. Correctly set speeds based on DDR frequency. Control the speeds in the predriver circuits to reduce power. SPEED[1:0] 2'b00:less than 800Mbps(400MHz) 2b01 : 800Mbps(400MHz) to 1600Mbps(800MHz) 2b10 : 1600Mbsp(800MHz) to 2400Mbps(1200MHz) 2b11 : 3200Mbps and greater 2. Configure the number of cycles for the phy clock pll wait time after locking, based on the DDR config file. BRANCH=none BUG=chrome-os-partner:56940 TEST=do memtester on kevin board, and pass Change-Id: Iaf6da59c6c5c290867e0922a2a99de272f4c7bde Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 125cf8afac3a682d33896fe74a20ba1d498a3bd2 Original-Change-Id: Iabc17df37a701c4f052540c3c259f209a1db3c59 Original-Signed-off-by: Lin Huang <hl@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/387428 Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16722 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins)
2016-10-07RISCV: update the encoding.h file.Ronald G. Minnich
Change-Id: I8997e927d82363921a3ff17580b9a575acc1ce16 Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-on: https://review.coreboot.org/16919 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
2016-10-07google/gru: set W2W_DIFFCS_DLY to 5Lin Huang
PHY_PER_CS_TRAINING is being enabled when DDR frequency >= 666. For per cs training, the controller should consider the PHY delay line switch time and there should be more cycles to switch the delay line, so update the W2W_DIFFCS_DLY_ value from 0x1 to 0x5. BRANCH=none BUG=chrome-os-partner:56940 TEST=do memtester on kevin board, and pass Change-Id: I00df2d4724b0b77f3e7565809fb35bbd2ff01ea5 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: c135ea3e33d810ed322d947eb8d512d1ac119cfc Original-Change-Id: I81b99cbc085769b7028e770509d79bd8d550820b Original-Signed-off-by: Lin Huang <hl@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/387506 Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16721 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07google/gru: pass apio number to arm-trust-firmwareLin Huang
To save power when entering suspend, gpios 2 to 4 need to be set to input and 'pull none' mode. Pass the APIO configuration to ATF so it can do a proper job here. BRANCH=None BUG=chrome-os-partner:56423 TEST=run suspend_stress_test on kevin board Change-Id: Id57fe8f622ae3f9c2bc7e58be89518b2b846cd37 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 9c42082d1ca9a6baa735821382d3e83c1f8dc9ad Original-Change-Id: Iaf441e8e34c5591ffe7c65f6533fcf0b733ff5ac Original-Signed-off-by: Lin Huang <hl@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/378475 Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com> Original-Tested-by: Caesar Wang <wxt@rock-chips.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16720 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07google/gru: pass the gpio power supply enable pin to bl31Lin Huang
We need to disable some regulators when the device goes into suspend. This means that we need to pass some gpios to bl31, and disable these gpios when bl31 runs the suspend function. BRANCH=None BUG=chrome-os-partner:56423 TEST=enter suspend, measure suspend gpio go to low [pg: also update arm-trusted-firmware to match] Change-Id: Ia0835e16f7e65de6dd24a892241f0af542ec5b4b Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 0f3332ef2136fd93f7faad579386ba5af003cf70 Original-Change-Id: I03d0407e0ef035823519a997534dcfea078a7ccd Original-Signed-off-by: Lin Huang <hl@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/374046 Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com> Original-Tested-by: Caesar Wang <wxt@rock-chips.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16719 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-07mainboard/google/reef: add pyro variant.Kevin Chiu
Create the initial Pyro variant which refers to the Reef. Pyro is APL Chrome board that deviate from reference board Reef. BRANCH=master BUG=None TEST=Build Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Change-Id: I9beed1f6895e8891d3d51b563edfe172f566718b Reviewed-on: https://review.coreboot.org/16855 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2016-10-06i2c/ww_ring: LED changes as per UX team feedback.Suresh Rajashekara
Colors and patterns as defined by the UX team BUG=b:31501528 TEST=Move the device to different states in FW using rec and dev button and verify the colors BRANCH=None Change-Id: I66d41a54590cd3ce4e5202c7cfa890f462fe195e Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 703559d5dddaeeb7d435d6cadbb2009a1b7a76c8 Original-Change-Id: I95ab1fa59b483396ff1498a28f1ee98ac08d02d7 Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com> Original-Reviewed-on: https://chromium-review.googlesource.com/387258 Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org> Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org> Original-Reviewed-by: Christopher Book <cbook@chromium.org> Original-Reviewed-by: Kan Yan <kyan@google.com> Reviewed-on: https://review.coreboot.org/16718 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06rockchip/rk3399: Configure USB3 controller to work in USB2 only modeLiangfeng Wu
In USB2 only mode, the Type-C PHY will be held in reset and only the USB2 logic of the USB3 OTG controller and PHY will be used over the USB2 pins on the Type-C connector to support Low, Full and High-speed USB operation. BRANCH=none BUG=chrome-os-partner:56425 TEST=Go to recovery mode, plug a Type-C USB drive containing chrome OS image into both ports in all orientations, check if system can boot from USB. Change-Id: Ic265c0c91c24f63b2f9c3106eb2bb277a589233b Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: a37ccc5b6019967483eac6b5a360d67bc3326e93 Original-Change-Id: I582f04f84eef447ff0ba691ce60e9461ed31cfad Original-Signed-off-by: Liangfeng Wu <wulf@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/385837 Original-Commit-Ready: Julius Werner <jwerner@chromium.org> Original-Tested-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16717 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06rockchip: rk3399: improve write leveling flowJianqun Xu
To improve sdram 800MHz and 933MHz stability, we need to modify write leveling flow to get the proper write leveling value. BUG=chrome-os-partner:56940 BRANCH=none TEST=Boot from kevin on 933MHz, and do stressapptest Change-Id: I5b24c93d4a57917fb9af7e5e2a95d8423ccbaa7e Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: d84bf25b3e5de373c7913e6d534a810cb984b3fd Original-Change-Id: I87efddf628c3683fcb85d6875e029cf3cbc482be Original-Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com> Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Original-Signed-off-by: Lin Huang <hl@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/384292 Original-Commit-Ready: Julius Werner <jwerner@chromium.org> Original-Tested-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16716 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06google/gru: Shrink RW_ELOG region to 4KBJulius Werner
Since there's currently a limitation in coreboot's code that prevents more than 4KB to be used by the eventlog anyway, this patch shrinks the available RW_ELOG area in the FMAP for Gru down to 4KB. This may prove prudent later if we ever resolve that limitation, so that tools can rely on the area in the FMAP being the same as the area actually used by the read-only firmware code on these boards. BRANCH=gru BUG=chrome-os-partner:55593 TEST=Booted Kevin, confirmed that eventlog got written normally. Ran a reboot loop to exhaust eventlog space, confirmed that the shrink code kicks in as expected before reaching 4KB. Change-Id: I3c55d836c72486665a19783fe98ce9e0df174b6d Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 05efb82ca00703fd92d925ebf717738e37295c18 Original-Change-Id: Ia2617681f9394e953f5beb4abf419fe8d97e6d3e Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/384585 Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Original-Reviewed-by: Simon Glass <sjg@google.com> Reviewed-on: https://review.coreboot.org/16715 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06rockchip/rk3399: Move TTB to the end of SRAMJulius Werner
We found that we may want to load some components of BL31 on the RK3399 into SRAM. As usual, these components may not overlap any coreboot regions still in use at that time, as is already statically checked by the check-ramstage-overlaps rule in Makefile.inc. On RK3399, the only such regions are TTB and STACK. This patch moves the TTB region back to the end of SRAM (right before STACK), so that a large contiguous region of SRAM before that remains usable for BL31. BRANCH=gru BUG=None TEST=Booted Kevin. Change-Id: I1689d0280d79bad805fea5fc3759c2ae3ba24915 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 1d4c6c6f6cc0efe97d6962a81e309a1c040d1def Original-Change-Id: I37c94f2460ef63aec4526caabe58f35ae851bab0 Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/384635 Original-Reviewed-by: Simon Glass <sjg@google.com> Reviewed-on: https://review.coreboot.org/16714 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06rockchip: rk3399: improve sdram noc timingLin Huang
sdram noc timing will affect ddr latency, this patch improves rk3399 sdram noc timing so improve memory performance. BRANCH=gru BUG=chrome-os-partner:57248 TEST=Boot from kevin board Change-Id: I09e984490a7ad747ef8abfc6542d0e2c95ec19bc Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 43dfe55d713d371e39d21312772fd353614b7642 Original-Change-Id: I393e74ecdeb72930ac38ae9bcf311e5654f65162 Original-Signed-off-by: Lin Huang <hl@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/382725 Original-Reviewed-by: Sonny Rao <sonnyrao@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-Tested-by: Sonny Rao <sonnyrao@chromium.org> Original-Commit-Queue: Sonny Rao <sonnyrao@chromium.org> Reviewed-on: https://review.coreboot.org/16713 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06rockchip: spi: Add support for 16-bit APB readsSimon Glass
With a SPI clock above about 24MHz the APB cannot keep up when doing individual byte transfers. Adjust the driver to use 16-bit reads when it can, to remove this bottleneck. Any transaction which involves writing bytes still uses 8-bit transfers, to simplify the code. These are the transfers that are not time-critical since they tend to be small. The case that really matters is reading from SPI flash. In general we can use 16-bit reads anytime we are transferring an even number of bytes. If the code detects an odd number of bytes, it tries to perform the operation in two steps: once in 16-bit mode with an even number of bytes, and once in 8-bit mode for the final byte. This allow us to use 16-bit reads even if asked to transfer (for example) 0xf423 bytes. The limit on in_now and out_now is adjusted to 0xfffe to avoid an extra transfer when transferring ~>=64KB. CQ-DEPEND=CL:383232 BUG=chrome-os-partner:56556 BRANCH=none TEST=boot on gru and see that things still work correctly. I tested (with extra debugging) that the 16-bit case is being picked when it should be. Change-Id: If5effae9a84e4de06537fd594bedf7f01d6a9c88 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: ec250b4931c7d99cc014e32ab597fca948299d08 Original-Change-Id: Idc5b7e5d82cdbdc1e8fe8b2d6da819edf2d5570c Original-Signed-off-by: Simon Glass <sjg@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/381312 Original-Commit-Ready: Julius Werner <jwerner@chromium.org> Original-Tested-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16712 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06rockchip/rk3399: lower kevin board sdram frequency to 800MHzLin Huang
We found some boards are not stable when sdram is run at 933Mhz. Before we can fix it, we need to lower the sdram frequency to 800MHz. In this patch we modify the DQS delay from 0x280 to 0x260 and extend the DQS window. BRANCH=None BUG=chrome-os-partner:56940 TEST=Booted Kevin. Change-Id: I68561c4aa4d9ab66acfa3515a42d696157aff759 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 877a7f6ad22a5bde9f9e458bcb65f133f2f001bd Original-Change-Id: I5eab6bbe96f0dae095c5353403292022e7a25421 Original-Signed-off-by: Lin Huang <hl@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/382724 Original-Commit-Ready: Douglas Anderson <dianders@chromium.org> Original-Tested-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-on: https://review.coreboot.org/16709 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06arm64: Use 'payload' format for ATF instead of 'stage'Simon Glass
Switch the BL31 (ARM Trusted Firmware) format to payload so that it can have multiple independent segments. This also requires disabling the region check since SRAM is currently faulted by that check. This has been tested with Rockchip's pending change: https://chromium-review.googlesource.com/#/c/368592/3 with the patch mentioned on the bug at #13. BUG=chrome-os-partner:56314 BRANCH=none TEST=boot on gru and see that BL31 loads and runs. Im not sure if it is correct though: CBFS: Locating 'fallback/payload' CBFS: Found @ offset 1b440 size 15a75 Loading segment from ROM address 0x0000000000100000 code (compression=1) New segment dstaddr 0x18104800 memsize 0x117fbe0 srcaddr 0x100038 filesize 0x15a3d Loading segment from ROM address 0x000000000010001c Entry Point 0x0000000018104800 Loading Segment: addr: 0x0000000018104800 memsz: 0x000000000117fbe0 filesz: 0x0000000000015a3d lb: [0x0000000000300000, 0x0000000000320558) Post relocation: addr: 0x0000000018104800 memsz: 0x000000000117fbe0 filesz: 0x0000000000015a3d using LZMA [ 0x18104800, 18137d90, 0x192843e0) <- 00100038 Clearing Segment: addr: 0x0000000018137d90 memsz: 0x000000000114c650 dest 0000000018104800, end 00000000192843e0, bouncebuffer ffffffffffffffff Loaded segments BS: BS_PAYLOAD_LOAD times (us): entry 0 run 125150 exit 1 Jumping to boot code at 0000000018104800(00000000f7eda000) CPU0: stack: 00000000ff8ec000 - 00000000ff8f0000, lowest used address 00000000ff8ef3d0, stack used: 3120 bytes CBFS: 'VBOOT' located CBFS at [402000:44cc00) CBFS: Locating 'fallback/bl31' CBFS: Found @ offset 10ec0 size 8d0c Loading segment from ROM address 0x0000000000100000 code (compression=1) New segment dstaddr 0x10000 memsize 0x40000 srcaddr 0x100054 filesize 0x8192 Loading segment from ROM address 0x000000000010001c code (compression=1) New segment dstaddr 0xff8d4000 memsize 0x1f50 srcaddr 0x1081e6 filesize 0xb26 Loading segment from ROM address 0x0000000000100038 Entry Point 0x0000000000010000 Loading Segment: addr: 0x0000000000010000 memsz: 0x0000000000040000 filesz: 0x0000000000008192 lb: [0x0000000000300000, 0x0000000000320558) Post relocation: addr: 0x0000000000010000 memsz: 0x0000000000040000 filesz: 0x0000000000008192 using LZMA [ 0x00010000, 00035708, 0x00050000) <- 00100054 Clearing Segment: addr: 0x0000000000035708 memsz: 0x000000000001a8f8 dest 0000000000010000, end 0000000000050000, bouncebuffer ffffffffffffffff Loading Segment: addr: 0x00000000ff8d4000 memsz: 0x0000000000001f50 filesz: 0x0000000000000b26 lb: [0x0000000000300000, 0x0000000000320558) Post relocation: addr: 0x00000000ff8d4000 memsz: 0x0000000000001f50 filesz: 0x0000000000000b26 using LZMA [ 0xff8d4000, ff8d5f50, 0xff8d5f50) <- 001081e6 dest 00000000ff8d4000, end 00000000ff8d5f50, bouncebuffer ffffffffffffffff Loaded segments INFO: plat_rockchip_pmusram_prepare pmu: code d2bfe625,d2bfe625,80 INFO: plat_rockchip_pmusram_prepare pmu: code 0xff8d4000,0x50000,3364 INFO: plat_rockchip_pmusram_prepare: data 0xff8d4d28,0xff8d4d24,4648 NOTICE: BL31: v1.2(debug): NOTICE: BL31: Built : Sun Sep 4 22:36:16 UTC 2016 INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 INFO: plat_rockchip_pmu_init(1189): pd status 3e INFO: BL31: Initializing runtime services INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x18104800 INFO: SPSR = 0x8 Change-Id: Ie2484d122a603f1c7b7082a1de3f240aa6e6d540 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 8c1d75bff6e810a39776048ad9049ec0a9c5d94e Original-Change-Id: I2d60e5762f8377e43835558f76a3928156acb26c Original-Signed-off-by: Simon Glass <sjg@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/376849 Original-Commit-Ready: Simon Glass <sjg@google.com> Original-Tested-by: Simon Glass <sjg@google.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16706 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06rockchip: Correct and standardize clock divisor range assertionsJulius Werner
Some of the asserts for valid clock divisor ranges were off by one. This patch corrects them and writes them all in a consistent way. BRANCH=None BUG=None TEST=Booted Kevin. Change-Id: I81749408a40822100797f1734f3b88987d12d8d5 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: e09cdfde26700496aaa1fc41489f63a355e8a89d Original-Change-Id: I429edb99e2d5ff2302d9750e6569b3d21f5686fa Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/381574 Original-Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-on: https://review.coreboot.org/16704 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06spi: Add a way to show SPI transfer speed for readsSimon Glass
SPI read speed directly impacts boot time and we do quite a lot of reading. Add a way to easily find out the speed of SPI flash reads within coreboot. Write speed is less important since there are very few writes and they are small. BUG=chrome-os-partner:56556 BRANCH=none TEST=run on gru with SPI_SPEED_DEBUG set to 1. See the output messages: read SPI 627d4 7d73: 18455 us, 1740 KB/s, 13.920 Mbps Change-Id: Id3814bd2b7bd045cdfcc67eb1fabc861bf9ed3b2 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 82cb93f6be47efce3b0a3843bab89d2381baef89 Original-Change-Id: Iec66f5b8e3ad62f14d836a538dc7801e4ca669e7 Original-Signed-off-by: Simon Glass <sjg@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/376944 Original-Commit-Ready: Julius Werner <jwerner@chromium.org> Original-Tested-by: Simon Glass <sjg@google.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16701 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06google/veyron_rialto: Add lpddr3-K4E6E304EB-2GB-1CH memory configurationJeffy Chen
Add lpddr3-K4E6E304EB-2GB-1CH memory configuration for rialto. BUG=chrome-os-partner:56759 BRANCH=none TEST=Build Change-Id: I698fe450d48b64a06232aa44ecf91d688d9dc17a Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: d3edecdb135939c3264ab1b831e7821d3a3e0149 Original-Change-Id: I7dae9fd822abeff5b08de0ab9262e1817ac58531 Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/380443 Original-Commit-Ready: Alexandru Stan <amstan@chromium.org> Original-Tested-by: Alexandru Stan <amstan@chromium.org> Original-Reviewed-by: Alexandru Stan <amstan@chromium.org> Original-Reviewed-by: Jonathan Dixon <joth@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16699 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2016-10-06rockchip/rk3399: Move big CPU cluster initialization into ramstageJulius Werner
This patch moves the big CPU cluster initialization on the RK3399 from the clock init bootblock function into ramstage. We're only really doing this to put the cluster into a sane state for the OS, we're never actually taking it out of reset ourselves... so there's no reason to do this so early. Also cleaned up the interface for rkclk_configure_cpu() a bit to make it more readable. BRANCH=None BUG=chrome-os-partner:54906 TEST=Booted Kevin. Change-Id: I568b891da0abb404760d120cef847737c1f9e3ec Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: bd7aa7ec3e6d211b17ed61419f80a818cee78919 Original-Change-Id: Ic3d01a51531683b53e17addf1942441663a8ea40 Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/377541 Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-on: https://review.coreboot.org/16698 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-06i2c/ww_ring: Change LED configuration for Gale EVT3Suresh Rajashekara
Gale EVT3 has only one LED controller (earlier we had 2). Remove the support for the second controller and also the corresponding microcode. The color values used are the same as onHub (Arkham to be specific). BUG=b:30890905 TEST=Move the device to different states manually by appropriate actions (like dev mode, rec mode etc) and observe the different colors. BRANCH=None Change-Id: I853035610ea7ea7c8d29c30d2de13c9e2e786b2b Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 593905d2d69daa7482318aa5f5c5cd7cf984043e Original-Change-Id: If8f22abd605faac6f6215ef600041740ce15ea0c Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com> Original-Reviewed-on: https://chromium-review.googlesource.com/370821 Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org> Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org> Original-Reviewed-by: Kan Yan <kyan@google.com> Reviewed-on: https://review.coreboot.org/16697 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-05drivers/i2c/tpm/cr50: Initialize IRQ status handler before probeDuncan Laurie
Move the setup of the IRQ status handler so it will be set up properly before the early probe happens. BUG=chrome-os-partner:53336 Change-Id: I4380af1233d2a252899459635a3cb69ca196088d Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/16861 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
2016-10-05siemens/mc_tcu3: Increase LCD backlight turn-on delay to 500 msWerner Zeh
Due to different LCD panel requirements the delay between LVDS becomes active and the backlight is switched on needs to be increased to 500 ms. Change-Id: I09029624469aef412141c7b46224d48557ba4af1 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/16875 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-04rockchip: spi: Set rxd sample delay when using high speedSimon Glass
At higher SPI bus speeds the SPI RX value is not available in time for sampling at the normal time. Add a delay to ensure that we read the correct data. The value of 40ns is chosen arbitrarily. In my testing I can use a sample delay of 1 even at 24MHz. But since it is not necessary, I have left that case alone. It kicks in at 25MHz and up. BUG=chrome-os-partner:56556 BRANCH=none TEST=boot on gru and see no change at current speed Change-Id: I3ef335d9a532eaef1e76034bd02e185acf11176a Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: e9b620c47fc3e39211487507fadb8657afdebee7 Original-Change-Id: I65d66d752cbbbee4d02f475de23a52069a0e9782 Original-Signed-off-by: Simon Glass <sjg@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/381311 Original-Commit-Ready: Julius Werner <jwerner@chromium.org> Original-Tested-by: Simon Glass <sjg@google.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16707 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2016-10-04google/gru: Ensure correct pull resistors for special-function pinsJulius Werner
Several of the special function pins we're using in firmware have a pre-assigned pull-up or pull-down on power-on reset. We don't want those to interfere with any of the signaling we're trying to do on those pins, so this patch disables them. Also do some house-cleaning to group the bootblock code better, and change the setup code for all SPI and I2C buses to first initialize the controller and then mux the pins... I assume this might be a little safer (in case the controller peripheral has some pins in a weird state before it gets fully initialized, we don't want to mux it through too early). BRANCH=None BUG=chrome-os-partner:52526 TEST=Booted Kevin. Change-Id: I4d5bd3f7657b8113d90b65d9571583142ba10a27 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: f8f7fd56e945987eb0b1124b699f676bc68d0560 Original-Change-Id: I6bcf2b9a5dc686f2b6f82bd80fc9a1a245661c47 Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/382532 Reviewed-on: https://review.coreboot.org/16711 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-04rockchip/rk3399: Fix rkclk_init() to actually use PERILP1_PCLK_HZJulius Werner
This patch fixes a typo in the clock initialization code that caused the PERILP1_PCLK_HZ constant to be ignored and the clock to always run at the same speed as its parent (PERILP1_HCLK_HZ). Since we've done all our previous tests and validation with this bug, we should probably increase the value of the constant (that had not actually been used) to the value that we had been incorrectly using instead (which also makes effective SPI read times faster). BRANCH=None BUG=chrome-os-partner:56556 TEST=Booted Kevin. Change-Id: Ibeb08f5fe5e984a74e3f57e60c62d4bfb644b6ca Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 06e605a5fcb9bdf13a3d301112380633b892fd4e Original-Change-Id: Icb5e079f53eb22b0dbf0ea4d1c2ff08688e3fa8e Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/381031 Original-Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-on: https://review.coreboot.org/16703 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-04gru: Increase SPI speed to 33MHzSimon Glass
Increase the SPI bus speed to speed up boot time. The maximum supported speed at 1.8V is 37.5MHz, and 33MHz is the next lowest convenient speed, given the clock parents. BUG=chrome-os-partner:56556 BRANCH=none TEST=boot on gru and see that things still work correctly. Total time spent on reading from SPI reduces from 185ms to 141ms. Change-Id: I71436c9e343b18360fa63d528dea5cfcfbc831e6 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: d7576f6e53e407af61160be142c3d589e864a8cf Original-Change-Id: I55a19f523817862e081d23469e94fd795456dd67 Original-Signed-off-by: Simon Glass <sjg@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/381313 Original-Commit-Ready: Julius Werner <jwerner@chromium.org> Original-Tested-by: Simon Glass <sjg@google.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16708 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-04rockchip: Remove pulls for gpio_output(), clean up codeJulius Werner
Output GPIOs should never have a pull-up or pull-down resistor attached since they're actively driven. Since some GPIOs get initialized with a pull at power-on reset, we should explicitly overwrite that setting. Most other platforms do this on gpio_output, but Rockchip hadn't yet. Also, shuffle some code around to make things cleaner and allow for easier code reuse. BRANCH=None BUG=chrome-os-partner:52526 TEST=Booted Kevin. Change-Id: I1425d074ea1e90f4484e1e84a8002b057192c5f7 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: df5b236bfd58b172435043c1cb792b917a4ec4ab Original-Change-Id: I044266d71ef8bd0518316ff72d829d1ca1e30f35 Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/382531 Original-Reviewed-by: Simon Glass <sjg@google.com> Reviewed-on: https://review.coreboot.org/16710 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-04google/gru: Init the PWM pinmux after setting up the PWMDouglas Anderson
If we setup the PWM _after_ the pinmux then there's a period of time when we're driving the PWM incorrectly. Let's setup the regulator and _then_ configure the pinmux. This fixes no known bugs, but it is more correct and probably makes the signals look better at bootup. BRANCH=None BUG=None TEST=scope Change-Id: I311c0eded873b65e0489373e87b88bcdd8e4b806 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: fcf4d0ba29d82cce779c0b25ead36de4a95d97a1 Original-Change-Id: I5124f48d04a18c07bbd2d54bc08ee001c9c7e8d1 Original-Signed-off-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/381592 Original-Reviewed-by: Simon Glass <sjg@google.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/16700 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-04rockchip/rk3399: Remove CONFIG_ARM64_A53_ERRATUM_843419Julius Werner
As far as I know, the Cortex-A53 cores in RK3399 are of a newer revision that is not affected by ARM erratum 843419. If it was, the workaround would also need to be enabled in libpayload and Chrome OS userspace, which it currently isn't. I assume this was just incorrectly copied over from another SoC and we can safely remove it. BRANCH=None BUG=chrome-os-partner:56700 TEST=Booted Kevin. Change-Id: I5b1534c954a6d985499b481738723cabbdc07253 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 4891cc866583532ee3dcb1a5ad5b81670eb0743d Original-Change-Id: Iadb57428f8727ce0e563204723644e2c79e3007c Original-Signed-off-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/376363 Original-Commit-Queue: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-on: https://review.coreboot.org/16702 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-04mainboard/siemens/sitemp_g1p1: Use tabs for indentsElyes HAOUAS
Change-Id: Ia5ea2198cdc93822723a4fe5440d574d76cb4de2 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16847 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-04src/northbridge: Remove unnecessary whitespaceElyes HAOUAS
Change-Id: Ib06ecd083f00c74f1d227368811729d2944dd1ef Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16851 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-04util/release: Update genrelnotes.script to the latest versionMartin Roth
Internal changes: - Fix shellcheck issues. - Add some help text and update section header text. - Reorder sections to try to get better estimates of what the commits were mainly touching. - Start making the script slightly less coreboot-centric. - Don't print git errors. Changes in output: - Find new and deleted CPUs, SOCs, northbridges, southbridges, and SIOs. - Show new users. - Show before and after commit count for all authors. Change-Id: I9858436f9458b2859a91273a525901df34796df4 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16848 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2016-10-04nb/gm45: allow use of 352M preallocated ram for igdArthur Heymans
The datasheets on gm45: "Mobile Intel® 4 Series Express Chipset Family" mention the possibility of having 352M ram preallocated for the integrated graphic device. This only worked fine if the amount of ram in the system was 3GB or less. When 4G or more is installed, memory is remapped to create a 1GB large pci mmio hole which is not enough and creates conflicts when 352M vram is used. This patch increases the pci mmio hole size on Lenovo x200 to allow 352M vram to work. TEST: build and flash on target with 4GB ram or more, use nvramtool to set gfx_uma_size to 352M and reboot. Change-Id: I5ab066252339ac7d85149d91b09a9eaaaab3b5b6 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/16831 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-04src/cpu: Remove whitespace after sizeofElyes HAOUAS
Change-Id: I30b911a8444529653c8ea4a736a902143fe7ab20 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16864 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
2016-10-04src/northbridge: Remove whitespace after sizeofElyes HAOUAS
Change-Id: Iea0352f85f4d5f47fc906edbe625e7bbf3f03afd Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16863 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins)
2016-10-04src/southbridge: Remove unnecessary semicolonElyes HAOUAS
Change-Id: I52c3ec75d44290b758b6e952344aa9a768bc2617 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16857 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-04mainboard/amd/torpedo: Improve code formattingElyes HAOUAS
Change-Id: I18de4740e0d3512ec81e10b32d13d07a35791b57 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16846 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-04src/mainboard: Remove unnecessary semicolonElyes HAOUAS
Change-Id: Iab0c7c470a3105b5df7b6b74aebdd1329e7f93ba Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16859 Tested-by: build bot (Jenkins) Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
2016-10-04samsung/lumpy: Swap SPD assignmentsKyösti Mälkki
On-board memory is on channel 1. This fixes native raminit with 4GiB SO-DIMM installed. Change-Id: If1b94e050d7e8d0dbd349c0415a182730aa5fa90 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/16845 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-03Revert "util/lint/kconfig_lint: change warning levels and text"Martin Roth
This reverts commit dfdb0733a6a71b11d15006dafc13841e84fab7cd. Change-Id: I91bf5e42f4ac241f544742ce161bae651f9f9947 Reviewed-on: https://review.coreboot.org/16868 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins)
2016-10-03google/gale: Remove #ifdef of Kconfig bool symbolMartin Roth
Kconfig symbols of type bool are ALWAYS defined, so this code was always being included and run, which isn't what the author wanted. Change to use IS_ENABLED(), and a regular if() instead of an #ifdef. Change-Id: I72623fa27e47980c602135f4b73f371c7f50139b Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16837 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-10-03util/lint/kconfig_lint: change warning levels and textMartin Roth
- Add an exception for MAINBOARD_POWER_ON_AFTER_POWER_FAIL when checking - With those exceptions set, we don't have anymore #define or #ifdef warnings, so turn them to errors so no more can be pushed. - Change the definition of an unused symbol from a warning to a note. There are times when unused symbols are expected. - Upgrade the warning for loading Kconfig files multiple times from a warning to an error. Change-Id: I6dcb06d4f0b099d5ccaf7643e72dd790719bdf58 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16840 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-10-03util/lint/kconfig_lint: Check default typesMartin Roth
The type of the default value wasn't being checked to make sure that it matched the type of the Kconfig symbol. This makes sure that the symbol is being set to either a reasonable looking value or to another Kconfig symbol. Change-Id: Ia01bd2d8b387f319d29f0a005d55cb8e20cd3853 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16839 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-10-03google/gale/Kconfig: Change wording of Kconfig optionMartin Roth
Everybody knows WHAT they're supposed to do with options, so the text "Pick this" or "Select to" are redundant. Change-Id: I327c5be755373e99ca0738593bd78e1084d4d492 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16838 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-10-02mainboard/packardbell/ms2290: Use tabs for indentsElyes HAOUAS
Change-Id: I1559a2541a93a9969ac68708a04f0468790feb69 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16844 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-10-02mainboard/via/vt8454c: Improve code formattingElyes HAOUAS
Change-Id: Ida10672380f6dffec0daf0073f25f6badfcd83eb Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16843 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-02mainboard/apple/macbookair4_2: Use tabs for indentsElyes HAOUAS
Change-Id: I2714553e2521f8178538755e3cfadec5c1fc6b12 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16842 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-10-02vendorcode/amd/pi/Kconfig: update AGESA_BINARY_PI_LOCATION to hexMartin Roth
The AGESA_BINARY_PI_LOCATION Kconfig symbol was declared as a string. Change it to a hex value. Change-Id: Ifd87b6c8dfcdf950aea9b15a6fea45bb72e8b4e9 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16835 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-10-02Kconfig: Update default hex values to start with 0xMartin Roth
Kconfig hex values don't need to be in quotes, and should start with '0x'. If the default value isn't set this way, Kconfig will add the 0x to the start, and the entry can be added unnecessarily to the defconfig since it's "different" than what was set by the default. A check for this has been added to the Kconfig lint tool. Change-Id: I86f37340682771700011b6285e4b4af41b7e9968 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16834 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-10-02TPM2: Fill in empty tlcl_resume function in TPM2 tlclFurquan Shaikh
On resume, TPM2_Starup(STATE) command needs to be sent to the TPM. This ensures that TPM restores the state saved at last Shutdown(STATE). Since tlcl_resume and tlcl_startup both use the same sequence for sending startup command with different arguments, add a common function that can be used by both. BUG=chrome-os-partner:58043 BRANCH=None TEST=Verified that on resume coreboot no longer complains about index read for 0x1007. Return value is 0 as expected. Change-Id: Ib8640acc9cc9cdb3ba5d40e0ccee5ca7d67fa645 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/16832 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-10-02apple/imac52: add mainboardArthur Heymans
Add Imac5,2 based on macbook2,1 port. Change-Id: I34c8313c32920b02a2b964d8718e5b2b6b5a6820 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/16638 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mb/kontron/ktqm77: Let suspend LED flash slowly in S3/S4Nico Huber
Change-Id: Idb37abea01831631aadba66ecd42bc7df03aa857 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/16727 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01sio/winbond/w83627dhg: Add ACPI function to control suspend LEDNico Huber
Change-Id: Ie2062672233141b6f34625e59cbb50238be0b5fa Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/16726 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01soc/intel/skylake: Add config option for Skylake-H Sku supportTeo Boon Tiong
Change-Id: Ia9c1c065f20bf2b37afc7485ef8df3abd35e2f14 Reviewed-on: https://review.coreboot.org/16607 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01superio/nuvoton: Add back Nuvoton NCT6776 supportTeo Boon Tiong
Revert commit 53552cc0 (Drop SuperIO nuvoton/nct6776), removing the code as no other mainboard uses it. The board Intel Saddle Brook uses this device, so add the code back with minor adaptations. Change-Id: I546879285ad8336e81798d0fbdf94f72e1fa61a2 Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com> Reviewed-on: https://review.coreboot.org/16519 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01soc/intel/apollolake: Try to update BSP microcode from cbfsMartin Roth
The microcode for the BSP gets loaded early from the fit table, but in case we have newer microcode in cbfs, try to load it again from cbfs. BUG=chrome-os-partner:53013 TEST=Boot and verify that microcode tries to load into the BSP. Change-Id: Ifd6c78d7b0eec333b79e0fe5cb6a81981b078f5d Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16829 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-10-01southbridge/broadcom/bcm5785: transition away from device_tAntonello Dettori
Replace the use of the old device_t definition inside southbridge/broadcom/bcm5785. Change-Id: I091b07439ff918efa52cf8f8270484131fd0cec5 Signed-off-by: Antonello Dettori <dev@dettori.io> Reviewed-on: https://review.coreboot.org/16690 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01northbridge/via/cn700: transition away from device_tAntonello Dettori
Replace the use of the old device_t definition inside northbridge/via/cn700. Change-Id: Ib7761697daad3c459f3568e5158f925199bcd919 Signed-off-by: Antonello Dettori <dev@dettori.io> Reviewed-on: https://review.coreboot.org/16689 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01cpu/amd/model_fxx: transition away from device_tAntonello Dettori
Replace the use of the old device_t definition inside cpu/amd/model_fxx. Change-Id: Iac7571956ed2fb927a6b8cc88514e533f40490d0 Signed-off-by: Antonello Dettori <dev@dettori.io> Reviewed-on: https://review.coreboot.org/16437 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01biostar/am1ml: transition away from device_tAntonello Dettori
Replace the use of the old device_t definition inside mainboard/biostar/am1ml. Change-Id: Iba2fff5617c62152355b54e446517ad36108aa31 Signed-off-by: Antonello Dettori <dev@dettori.io> Reviewed-on: https://review.coreboot.org/16688 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-01mainboard/google/reef: Update DPTF policy temp. values for CPUSumeet Pawnikar
This patch increases the CPU specific passive temp. trip point and critical temp. trip point value for DPTF policy. BUG=chrome-os-partner:57903 TEST=Built, booted on reef and verified this passive and critical temp. trip points with heavy workload. Change-Id: I2a38d01a6539c1bd478f8716c4b543ebcd1f2080 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/16766 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
2016-10-01mainboard/google/reef: unconditionally set MAINBOARD_FAMILYAaron Durbin
For all mainboard variants use the "Google_Reef" family by default which is populated in SMBIOS tables. A variant can provide their own value if needed, but "Google_Reef" can reside as the family without having to add conditions for each variant when MAINBOARD_FAMILY have to be overridden. BUG=chrome-os-partner:56677 Change-Id: Ic214eae1e6473b32f4cb442c09c34355357e1257 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16813 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2016-10-01mainboard/amd/serengeti_cheetah: Use tabs for indentsElyes HAOUAS
Change-Id: If47f0c072399fe8291bd8e41920d828f649ec49f Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16817 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-10-01mainboard/*/*/*/usb.asl: Use tabs for indentsElyes HAOUAS
Change-Id: Id46a0c4ca59dc7224c2eedd674ea3a5486509de1 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16824 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mainboard/gigabyte/m57sli/romstage.c: Use tabs for indentsElyes HAOUAS
Change-Id: Ib439e5d96543790d17934bd477af62d39a5958b6 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16815 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mainboard/jetway/j7f2: Use tabs for indentsElyes HAOUAS
Change-Id: Id97981a05ce4af371c765c6950ed504557b0a584 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16825 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mainboard/winent/mb6047: Use tabs for indentsElyes HAOUAS
Change-Id: Iaf5ad440cfc2bbe08ea9f6c545e5e314645c8893 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16823 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mainboard/kontron/ktqm77: Use tabs for indentsElyes HAOUAS
Change-Id: I3040dc9a2534a77087805ee61c4f91d1bdb4d509 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16822 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mainboard/digitallogic/msm800sev: Use tabs for indentsElyes HAOUAS
Change-Id: I39ad6606869f059b2ef0c45d6741b844b3791655 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16821 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mainboard/gigabyte/ga-b75m-d3v: Use tabs for indentsElyes HAOUAS
Change-Id: I36011719f79da4a9ab2aaeb92ffb0506b4373143 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16816 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mainboard/gigabyte/ga-b75m-d3h: Use tabs for indentsElyes HAOUAS
Change-Id: I038e5cea654d1760ddb2c403c651d8f75e021251 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16819 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mainboard/samsung/stumpy: Use tabs for indentsElyes HAOUAS
Change-Id: I1ffee53a04df6874f658feb3d6ce7d5c7b922837 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16818 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-10-01mainboard/kontron/986lcd-m: Use tabs for indentsElyes HAOUAS
Change-Id: Ibeb0da2f75b4aec32f5238e5634bc1f1d8220b84 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/16820 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2016-09-30google/reef: Fix default values in KconfigMartin Roth
These default values weren't being set with the default keyword so were ending up with different values. from the default generated config file before this change: CONFIG_DRIVER_TPM_I2C_BUS=0x9 CONFIG_DRIVER_TPM_I2C_ADDR=0x2 CONFIG_DRIVER_TPM_I2C_IRQ=-1 Change-Id: I19514d0c9b2a9b7e479f003a4d3384e073f4d531 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/16828 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-26 10:43:33 +0000