| Age | Commit message (Collapse) | Author |
|---|
|
This code was never tested with SSE enabled. Now qemu enables it and
FX_SAVE encroaches on the save states. Without SSE enabled the handler
just happened to be aligned downwards enough to have the save states
fit. With SSE enabled that's not the case. The proper fix is to give the
code setting up stubs the right base address, which is the same as for
the TSEG codepath.
Change-Id: I45355efb274c6ddd09a6fb57743d2f6a5b53d209
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69233
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Provide timing parameter for SSDT generation to achieve the requested
100 kHz speed with a high accuracy.
Test: Measure I2C bus clock, high and low times during I2C access from
Linux and confirm they match the specification.
Change-Id: Ifb6019421b612133b8f25c076519bc0e7200dad8
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
In Linux, the I2C speed defaults to 400 kHz if there is no device
registered in ACPI which requests a different speed. Due to board
limitations (layout, bus load), 400 kHz are too fast which results in a
timing violation. Therefore, add a dummy I2C device to both used I2C
buses (I2C1 and I2C2) with a speed of 100 kHz. This will limit the bus
speed in Linux accordingly.
Change-Id: I507c53c9ec7f763cef18903609231b1a66ed98fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
According to measurements Elkhart Lake seems to drive the internal I2C
controllers with 100 MHz instead of the common 133 MHz. The datasheet
itself is quite vague on this definition, just one place mentions that
it is 100 MHz (register description for offset 0x94).
This patch changes the I2C controller base frequency to 100 MHz. The
verification was done by measuring the set up resulting I2C clock for
both 100 and 400 kHz.
Change-Id: I7c826bbb01b53e3661746e49f25441565068d1c2
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
There are SoCs (for instance Intel Elkhart Lake) that do use 100 MHz as
the base clock for I2C controllers. To support them properly add a
frequency setting for 100 MHz to the designware I2C controller driver.
Change-Id: I9ea11c6a41fd3758b771a416251e108cbe722769
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Add wifi sar table for craask/craaskbowl.
Use fw_config to separate different project settings.
BUG=b:247652032,b:251287099,b:251287101
Test=emerge-nissa coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: I5c92f0ab53ece12a97068f09241e5298909116aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
On certain mainboards due to hardware design limitations, certain SPI
Read Modes eg. (Dual I/O 1-2-2) cannot be supported. Add ability to
override SPI read modes in boards which do not have hardware
limitations. Currently there is an API to override SPI fast speeds.
Update this API for mainboards to override SPI read mode as well.
BUG=b:225213679
TEST=Build and boot to OS in Skyrim. Observe a boot time improvement of
~25 ms with 100 MHz SPI speeds.
Before:
11:start of bootblock 688,046
14:finished loading romstage 30,865
16:FSP-M finished LZMA decompress (ignore for x86) 91,049
Total Time: 1,972,625
After:
11:start of bootblock 667,642
14:finished loading romstage 29,798
16:FSP-M finished LZMA decompress (ignore for x86) 87,743
Total Time: 1,943,924
Change-Id: I160b56f6201a798ce59e977ca40301e23ab63805
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Add new ram_id:0 (0000) for memory part H9JCNNNCP3MLYR-N6E.
DRAM Part Name ID to assign
H9JCNNNCP3MLYR-N6E 0 (0000)
BUG=b:257867226
TEST=Use part_id_gen to generate related settings and
emerge-nissa coreboot
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: If663afbcd2e0457636f4a1c7475f1e3e40f0dd96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
SX9324 driver is updated per Linux's documentation found at
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/iio/proximity/semtech,sx9324.yaml
Supporting logic for the deprecated SX932x driver is hence guarded by
DRIVERS_I2C_SX9324_SUPPORT_LEGACY_LINUX_DRIVER
This patch by itself does not introduce functional changes to any board.
The legacy SX932x Linux driver never reached upstream Linux and is only
available in ChromeOS kernel fork of 4.4 and 5.4. Linux later accepted
a different implementation named SX9324 and has been available since
5.4. Ideally all variants should adopt the new driver; however, during
the transition phase, coreboot must support both drivers. It is better
to have a single firmware build that can work with both Linux kernel
drivers by specifying both sets of properties. Legacy driver support
should be deleted once all variants finish migration.
BUG=b:242662878
TEST=Dump ACPI SSDT then verify _DSD entries related to the legacy
SX932x driver are identical w/ and w/o this patch
(Tested on Craask and Nivviks)
Change-Id: I42cd6841c3a270c242ed2e739db245e858eadb3b
Signed-off-by: Victor Ding <victording@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69192
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add Fingerprint SPI, and power-off FPMCU during romstage.
For reference see CL:66915 for a similar change to Brya's power sequence
SHA: 2b523ce6316e5c5ec86fe812d739fe48ca81d83d ("Invoke power cycle of
FPMCU on startup")
TEST=Tested on Rex - setup and logged in using fingerprint
Change-Id: I4e6be24e72a8232ae2c958a01cf8ea9a272d7365
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66992
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Handle the possible memory leak scenario.
Foundby=klocwork
BUG=NONE
TEST=Boot to OS on Nivviks
Change-Id: I01c4643d1e671d9bd9971ac6db8031634fffd61e
Signed-off-by: Shaik Shahina <shahina.shaik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69220
Reviewed-by: Shahina Shaik <shahina.shaik@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
These functions are added for ramstage:
* add IPMI OEM command to get board configuration.
* add function to get blade index in the sled.
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Signed-off-by: Jonathan Zhang <jonzhang@meta.com>
Change-Id: I85ec7ba68d580c13e368e7d656dba47ea043d33e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68779
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Kconfig SOC_RAS_BMS_SEL and corresponding support for
generating PCIe error SEL records and sending them to BMC.
Add PCIe error definitions.
This is needed for SMM, so build the ipmi kcs driver in SMM.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Signed-off-by: Rocky Phagura <rphagura@fb.com>
Signed-off-by: Jonathan Zhang <jonzhang@meta.com>
Change-Id: I1ee46c8da7dbccbe1e2cc00bfe62e5df2f072d65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68758
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch introduces support signing and verification of firmware
slots using CBFS metadata hash verification method for faster initial
verification. To have complete verification, CBFS_VERIFICATION should
also be enabled, as metadata hash covers only files metadata, not their
contents.
This patch also adapts mainboards and SoCs to new vboot reset
requirements.
TEST=Google Volteer/Voxel boots with VBOOT_CBFS_INTEGRATION enabled
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I40ae01c477c4e4f7a1c90e4026a8a868ae64b5ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66909
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Intel FSPs of XEON server platforms define FSPX_CONFIG
instead of FSP_X_CONFIG, which is expected by coreboot.
Re-define in the common code.
Update coreboot code to use FSP_X_CONFIG consistently.
Tested=On OCP Delta Lake, boot up OS successfully.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: Ifa0e1efa1618fbec84f1e1f23d9e49f3b1057b32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The functions create_bpdt_hdr and create_cse_layout
in bpdt_1_6.c are defined to return pointers but
not integers as was previouly implemented.
Reported-by: Coverity(CID:1469323)
Reported-by: Coverity(CID:1469353)
Signed-off-by: Solomon Alan-Dei <alandei.solomon@gmail.com>
Change-Id: Idb78d94be7a75a25ad954f062e9e52b1f0b921dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
The 0x9a, 0x9b, and 0x9c postcodes are not used anywhere else in the
coreboot tree other than in arch/x86/tables.c. Add macros to
standardize these postcodes.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I16be65ffa3f0b253fe4a9bb7bfb97597a760ad3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
This patch groups vboot context, recovery reason and subcode saving, and
reboot calls into two handy functions:
- vboot_save_and_reboot() - save context and reboot
- vboot_fail_and_reboot() - store recovery reason and call function
above
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Ie29410e8985e7cf19bd8d4cccc393b050ca1f1c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69208
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Change-Id: I16aa756039973e164c887ff5237bda69d042a235
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Use "* MiB" instead of "<< 20".
Change-Id: Iab6592804961a34fae6dc8012bfbc70023421a49
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Also sort includes.
Change-Id: Ia4a3807e45777e2a596878fe09e3c80b1fd2704d
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Disable Pch PM Energy Report WA was added to enhance boot time
with HFPGA only. SoC needs reporting enabled.
BUG=None
TEST=Build and Boot Google, Rex and Intel, MTLRVP without any boot time regression..
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: If5f1f9c6ab31652977d436a49a3531edffbd60c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69042
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
The patch disables PCH USB2 Phy power gating to prevent possible display
flicker issue for moli board. Please refer Intel doc#723158 for
more information.
BUG=b:257415959
TEST=Verify the build for brask board
Change-Id: I518e90e9032e8f2186300b6b907cc9d84a1682e4
Signed-off-by: Ricky Chang <rickytlchang@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch replaces static index 0 for PMC read resources with PCI
configuration offset 0x10 (PWRMBASE).
TEST=Able to build and boot Google, Rex to OS.
Without this change:
[SPEW ] PCI: 00:1f.2 resource base fe000000 size 10000 align 0 gran
0 limit 0 flags f0000200 index 0
With this change:
[SPEW ] PCI: 00:1f.2 resource base fe000000 size 10000 align 0 gran
0 limit 0 flags f0000200 index 10
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Iee2523876a8045e70effd5824afc327d1113038b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
BUG=b:239495499
TEST=emerge-nissa coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: I026a8b3e1a27bedc3e0082e15e80a74a2f8adfda
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69197
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vidya Gopalakrishnan <vidya.gopalakrishnan@intel.com>
|
|
This patch supports multiple camera modules based on FW_CONFIG.
BUG=b:251235140
TEST=Test the changes with ov2740/hi556 camera.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I34dbf67634ecd364c40c6e934217af3d8efe1689
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jim Lai <jim.lai@intel.com>
Reviewed-by: Ricardo Ribalda <ribalda@google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
|
|
The patch disables PCH USB2 Phy power gating to prevent possible display
flicker issue for kinox board. Please refer Intel doc#723158 for more
information.
BUG=b:257373738
TEST=Verify the build for kinox board
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ifcf4f89ea4c61ec4f9a31edba069d2111ca06010
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Lisbon doesn't support thunderbolt.
BUG=b:246657849
TEST=FW_NAME=lisbon emerge-brask coreboot
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: Iac44315d000c3c0c572efb00e877d039e0308455
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68916
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This enables ACPI configuration and add ACPI table.
BUG=b:224325352
TEST=util/abuild/abuild -p none -t intel/mtlrvp -a -c max
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Change-Id: I8264197fd0acdd7e19b9a36fb22822447b013202
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66100
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Usha P <usha.p@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Fix readouts from the hardware monitor on Fintek F71808A Super I/O.
The HWM port is +5 to the base address stored in LDN 0x4 at index 0x60/0x61.
Referred to util/superiotool/winbond.c and the Linux kernel driver f71882fg.
Tested on a HP 500-319na (Memphis-S / IPM87-MP).
Signed-off-by: Ravi Mistry <rvstry@protonmail.com>
Change-Id: I2b2b98c62f9305c6f4885c2ce3b1444801dcb9d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The headers added are generated as per FSP v3361.07
In the future, when Alder Lake and Raptor Lake fsp align, Raptor Lake
fsp headers can be deleted and Raptor Lake soc will also use headers
from alderlake/ folder.
BUG=b:254054169
BRANCH=firmware-brya-14505.B
TEST=Boot to OS
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Change-Id: If486867477c88ad3e2ec5041ef94a0c364f5dfd6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
As AOP takes 500 msec delay to get up, moving aop load and reset to
romstage improves the performance.
BUG=b:218406702
TEST=reboot from AP console (on CRD3)
prior to fix (from cbmem dump):
1000:depthcharge start 1,139,809 (152,679)
after fix (from cbmem dump):
1000:depthcharge start 1,041,109 (46,353)
Signed-off-by: Sudheer Kumar Amrabadi <samrabad@codeaurora.org>
Change-Id: Iabc8ee8f6e7b14d237b0aeaae42da8077f9dafc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Enable x86 SHA accelerator for use by VBOOT library. This is useful when
CBFS verification verifies the hash of the file being loaded in x86.
BUG=b:227809919
TEST=Build and boot to OS in Skyrim. Observe a boot time improvement of
~10 ms with CBFS verification enabled.
Change-Id: I14efe7be66f28f348330580d2e5733e11603a023
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68954
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently build rules allow using x86 SHA extensions for all coreboot
stages when enabled. On some SoCs where verstage can run in non-x86
environment, x86 SHA extension cannot be used. Update build rules
accordingly such that x86 SHA extensions can be used in AMD SoCs. This
is particularly useful when CBFS verificiation is enabled which verifies
the hash of the CBFS file being loaded.
BUG=b:227809919
TEST=Build and boot to OS in Skyrim. Observe that hardware acceleration
is used when a CBFS file is loaded and observe an overall improvement of
10 ms.
Change-Id: I4f388e963eb82990cda41d3880e66ad937334908
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68953
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
No need to call a function that just instantly returns.
It greatly enhances readability to just check before calling a funtion
and it also removes an extra argument.
Change-Id: I4d57c45ede520160ef615725c023b7e92289a995
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This adds an initial mainboard code for mtlrvp, Intel Meteorlake
reference platform.
BUG=b:224325352
TEST=util/abuild/abuild -p none -t intel/mtlrvp -a -c max
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I097db4de9734ff81283cf470aabf3eb23b63aab8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66097
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Balaji Manigandan <balaji.manigandan@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
RTD3,_ON method sometimes can create delays during system boot.
Even when the power is already up, kernel still tries to call _ON
method to power up device, but it's unnecessary.
RTD3._STA returns device power, so _ON method can check _STA and see
if the power on process can be skipped
BUG=b:249931687
TEST=system can boot to OS with RTD3 pcie storage and save ~80 ms on
Crota. Suspend stress test passes 100 cycles
Change-Id: I296ce1b85417a5dbaca558511cd7fc51a3a38c84
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Switch cases expect a statement so move the default label.
TEST: With BUILD_TIMELESS=1 binary remains identical.
Change-Id: I9a5d39bb3cbde64f82fc90186b0f2fb64bcde595
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66266
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch implements a function to enable IOSF Primary Trunk Clock
Gating.
BUG=b:253210291
TEST=Able to build and boot rex to OS. Also needed for S0ix, tested
with Sandbox OS + Firmware combination for S0ix entry/exit.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I02e191336e99f97f4db58b27f4414001b642ad02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68430
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I027c3aa7bb206112107ee120cf6f9854e37c5636
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69230
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
const void is a meaningless return type and clang complains about
incompatible function pointer signatures.
Change-Id: Ia00706b9cd718e590819621986dbd20555f6c226
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This contains the following commits:
* 835724d: mainboard/starlabs/starbook: Update the EC binaries
for StarLabs
* ecbe941: soc/mediatek: Update capitalization of coreboot
* 0e4444e: soc/mediatek/mt8188: Update MCUPM firmware from
v1.01.02 to v1.01.03
* 88570f6: mainboard/starlabs/starbook/adl: Update the EC binary
to 1.01 by Sean Rhodes
* f8e84db@ mainboard/starlabs/cezanne/starbook: Add EC binary
1.02 by Sean Rhodes
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I7afd43102718f211fe8d4fd69061dcdce5bfc323
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable the mirror flag for CML and TGL.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I51678bdb8d876d238076e12c6315a53c5da59628
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
When enabled, the EC will mirror the firmware contained inside the
coreboot ROM. This allows it to be updated at the same time as
coreboot.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ief088e012b65be32648f581fc3190e1000bca241
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update section now that google/skyrim and google/guybrush implement
power sequencing and touchscreen runtime detection.
Change-Id: Ida63bebf18575d6856edfc65965ff82a4072df87
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Now that coreboot performs the necessary power sequencing, switch
from using the 'probed' flag to 'detect' for all I2C touchscreens.
This alleviates ChromeOS from having to probe to see which
touchscreen model is actually present, prevents breaking ACPI spec
by generating device entries with status 'enabled and present'
which aren't actually present, and improves compatibility with
upstream Linux and Windows.
BUG=b:121309055
TEST=build/boot ChromeOS and Linux on guybrush, ensure touchscreen is
functional, and ACPI device entry generated for correct touchscreen
model.
This mirrors the changes made for skyrim in CB:67779.
Change-Id: Ib6a76b969d3a245eccde5352231eb7e36736f2e0
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
As all variants have a touchscreen option, in baseboard table set the
enable GPIO high and hold in reset during romstage, then release reset
in ramstage. This will allow the touchscreen to make use of the runtime
I2C detect feature (enabled in a subsequent commit) so that an ACPI
device entry is created only for the touchscreen actually present.
Variants/SKUs which do not have a touchscreen (if any) can use the
romstage/ramstage GPIO override tables to set the associated enable/
reset GPIOs to NC.
This mirrors the change to skyrim in CB:67778.
BUG=b:121309055
TEST=build/boot guybrush with rest of patch series
Change-Id: I9b3356b8b3a0e68a307838a4b18775d25b32e548
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This is the script used to generate the list of platforms that were
removed from the master branch at each release. Generate a list for the
old branch, another for the new, and compare the two.
Representative output:
```eval_rst
+-------------------------+-------------------+------------+----------+
| Vendor/Board | Processor | Date added | Brd type |
+=========================+===================+============+==========+
| 51nb/x210 | INTEL_KABYLAKE | 2020-03-16 | laptop |
| acer/aspire_vn7_572g | INTEL_SKYLAKE | 2022-01-28 | laptop |
| acer/g43t-am3 | INTEL_X4X | 2020-09-28 | desktop |
| amd/bilby | AMD_PICASSO | 2021-02-17 | eval |
| amd/birman | AMD_MORGANA | 2022-10-10 | eval |
| system76/whl-u | INTEL_WHISKEYLAKE | 2021-04-14 | laptop |
| ti/beaglebone | TI_AM335X | 2013-05-26 | sbc |
| up/squared | INTEL_APOLLOLAKE | 2019-05-22 | mini |
+-------------------------+-------------------+------------+----------+
```
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I4f7265d95df31f3a74aa2aa164f6a094c1139750
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The patch sets the EPP to 50% (0x80) for Vell. With EPP at 50%, the Vell
system demonstrated better power improvement without sacrificing the
performance.
PLT Results(Perf) with EPP@40% and EPP@50%:
EPP@40%: Device1-656 mins, Device2-664 mins.
EPP@50%: Device1-678 mins, Device2-677 mins.
In short, with EPP@50%, PLT KPI ran for more than 13 to 22mins compared
to EPP@40%.
Branch=firmware-brya-14505.B
BUG=b:215526166
TEST=Verified code build for Vell board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I41b15b84025d25cf59dac2d85826a3de9d725bae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Only a subset of variants has proximity sensors.
This patch by itself does not introduce functional changes to any board.
It is mainly to ease migrating SX9324 from the legacy driver to the
linux one - allowing gradual migration variant by variant.
BUG=b:242662878
TEST=Dump ACPI SSDT then verify they are identical w/ and w/o this patch
Change-Id: Ic00e0d9eafcef2c9eaf32571fecf6190777cec36
Signed-off-by: Victor Ding <victording@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69191
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
No platform uses this anymore.
Change-Id: Ifccb59ae45daa8fec41a9a2d46c628ff24a0c998
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69140
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Now that all platforms use parallel_mp this is the only codepath used
for cpu_info() local thread storage.
Change-Id: I119214e703aea8a4fe93f83b784159cf86d859d3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69122
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This codepath is deprecated after the 4.18 release.
Change-Id: I7e90f457f3979781d06323ef1350d5fb05a6be43
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69121
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This is deprecated after the 4.18 release.
Change-Id: I17327c31f8ade51716578e45c2d90a327efcd4ad
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69128
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This code is now unused by any platform.
Change-Id: I60afbde6ead70f0c887866fc351b4a6a15a89287
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69120
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This code is now unused by any platform.
Change-Id: I5464daa8cfb8231e2b19447c343fc80ab1d68ce8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69119
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Now that all agesa CPUs are removed this code is unused.
Change-Id: If0c082bbdb09457e3876962fa75725add11cb67c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69118
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
No platform uses this.
Change-Id: If32a4de7ef263f1d4f7ab7a36751ad9dcf52dc7e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69127
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This platform use the LEGACY_SMP_INIT which is to be deprecated after
release 4.18.
Change-Id: Ie2ef5424c3ebe75ff98361639a0f9980101c1141
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69126
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This platform use the LEGACY_SMP_INIT which is to be deprecated after
release 4.18.
Change-Id: I589f30ccf81b6cf243ac7cbf8320a3f830649ad8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69117
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This platform use the LEGACY_SMP_INIT which is to be deprecated after
release 4.18.
Change-Id: I749cf33fad12bb9bc5cd5d682df2652107d60a0f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69125
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This platform use the LEGACY_SMP_INIT which is to be deprecated after
release 4.18.
Change-Id: I18eb1c1ccad16980a4e57318dec411b82c45b25a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69116
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This platform use the LEGACY_SMP_INIT which is to be deprecated after
release 4.18.
Change-Id: I9dd3ce763418ff767acd0c55be26a998df77081b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69124
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This platform use the LEGACY_SMP_INIT which is to be deprecated after
release 4.18.
Change-Id: Ieaac0a32e71d208b66fd2c4e26f5349abc921d4f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69115
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This board use the LEGACY_SMP_INIT which is to be deprecated after
release 4.18.
Change-Id: Idf37ade31ddb55697df1a65062c092a0a485e175
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69114
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
These boards use the LEGACY_SMP_INIT which is to be deprecated after
release 4.18.
Change-Id: I43c7075fb6418a86c57c863edccbcb750f8ed402
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
These boards use the LEGACY_SMP_INIT which is to be deprecated after
release 4.18.
Change-Id: I3495d140a244bbbf63e846fcd963d69907e09719
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
These boards use the LEGACY_SMP_INIT which is to be deprecated after
release 4.18.
Change-Id: I9efb5cb1149cc4cf6337c47af8a2f4c4b55f4368
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The GPIO debounce timebase bit 4 is only 183uS on Picasso. On the other
SoCs it is 244uS. This affects the 1mS and 2mS actual debounce times
slightly.
Time PCO Others
1mS 0.915mS 1.220mS
2mS 2.013mS 2.684mS
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Id84bef75e6ab134778721ca269d763a4bb2ddde5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69209
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the marasov variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:254365935
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_MARASOV
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Ibe2dc442480f6a73877b40625e228cdb2038aa4d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69052
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-by: Kyle Lin <kylelinck@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
BUG=none
TEST=Able to build and boot Google, Rex SKU2 (Micron LPDDR5x
MT62F1G32D2DS-026).
Without this code change:
[INFO ] SPD: module type is UNKNOWN
With this code change:
[INFO ] SPD: module type is LPDDR5X
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: If620cf51133ca295fd3f1cbecbb472beb337b9fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69226
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to document 337348-001 (Intel® 300 Series and Intel® C240
Series Chipset Family Platform Controller Hub Datasheet - Volume 2
of 2), the only GPIOs that support PWROK reset are those in the GPD
group. The mappings themselves are correct, but they're assigned to
the wrong communities.
Change-Id: Ib586c987f768ddff31b053f4c108a8526326a7dc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69214
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The fingerprint(FP) feature is only for volmar,and it's not for zavala.
Add FPMCU_MASK field in fw_config to disable the FP function for
zavala, and reserve FP function for shipped volmar.
Define the value as following:
field FPMCU_MASK 10
option FPMCU_ENABLED 0
option FPMCU_DISABLED 1
end
BUG=b:250807253
TEST=build firmware and verify the fp function in volmar DUT.
write `disable=1` and 'enable=0' in FPCMU_MASK field.
check the fp function and run `ectool --name cros_fp version`
It works as expected.
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I867771904811459697056662d5e29c545a1a9474
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68917
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I80baadd405b31d6be2fdbb894b0f4b7c775da6f8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Rename so table more indicative of when GPIOs are set, and so it can
be used for more than just setting PCIe GPIOs. Will be used to set
touchscreen GPIOs as part of power sequencing in a subsequent commit.
Rename all variant tables and getter functions to match.
This mirrors the changes made for skyrim in CB:67810
Change-Id: I72e7febfb532262be7e4c14bf136e0d69c91301e
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Rename variant_pcie_gpio_table() to baseboard_pcie_gpio_table(), since
the GPIO table comes from the baseboard and is overridden by a separate
table from the variant.
Drop the __weak qualifier as this function is not overridden.
This is similar to the change made for skyrim in CB:67809
Change-Id: I14c79fad04f18d874ce6ff7e572bb237445db8b1
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The patch disables PCH USB2 Phy power gating to prevent possible display
flicker issue for moli board. Please refer Intel doc#723158 for
more information.
BUG=b:257373742
TEST=Verify the build for moli board
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I457d410501be996f0f29ec622e1829f1581c4970
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69193
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
|
|
In function 'set_power_limits' there is a path to bail out early if the
Kconfig switch SOC_INTEL_DISABLE_POWER_LIMITS is selected. In this case
reading the MSR PLATFORM_INFO is useless and can be avoided. So read it
right before the value is needed.
This was found by the scanbuild.
In addition, fix an unnecessary line break to increase code readability.
Change-Id: Ibdededdfd56287fb9b9223e78033a3cd6425e1a2
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Exposing the GPIOs via an ACPI PowerResource and the _CRS results in the
OS driver and ACPI thinking they own the GPIO. This can cause timing
problems because it's not clear which system should be controlling the
GPIO. I'm making this an error because we should really clean these up.
BUG=b:210694108
TEST=Boot guybrush and see error:
> I2C: 02:5d: ERROR: Exposing GPIOs in Power Resource and _CRS
> \_SB.I2C1.H05D: Goodix Touchscreen at I2C: 02:5d
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ifcc42ed81fff295fb168a0b343e96b3a650b1c84
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
When using site-local we need to have ability to override
MAINBOARD_BLOBS_DIR with a different location (presumably somewhere in
site-local). site-local Makefiles.inc should be pulled in first
(different CL) allowing MAINBOARD_BLOBS_DIR to be overwritten.
Change-Id: I028042b947887d1182642ad4482dd1bba7ad8e23
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Use the common device ops instead of an soc-specific device ops.
TEST=builds for each soc
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I1804200c3c3f5ab492d237f4b03484c383862caf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add the generic data_fabric_acpi_name function and device ops to common
code.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I12053389a12081ddd81912a647bb532b31062093
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Make the data_fabric_acpi_name function more generic, in preparation to
move it to common.
TEST=build chausie, dump ACPI tables, and inspect DFD0 to DFD7
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I77140d8d0d6bf3e048b737de03d18142a6e23c1d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
VPD read depends on CONFIG(VPD), not CONFIG(CHROMEOS).
TEST=build/boot snappy, verify SKU set properly in SMBIOS
Change-Id: I8aa57f793bd04dbe31f3b49bbff23e05c96592a6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Morgana/Glinda have a different register mapping for data fabric access,
although the registers themselves are mostly compatible. The register
layouts defined by each soc capture the differences and the common code
can use those.
Move the register offsets to soc headers and update the offsets for
morgana/glinda per morgana ppr #57396, rev 1.52 and glinda ppr #57254,
rev 1.51
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I9e5e7c85f99a9afa873764ade9734831fb5cfe69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Now that the socs have defined the DF FICAA and MMIO Control registers,
update the common code to use them.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Ia5566f7af6cf5444fc8c627e004dd08185468c77
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch enables the radio frequency interference mitigation for Rex.
BUG=b:248391777
TEST=Booted to OS on Rex board. Verified RFIM DSM is presented to kernel
through ACPI SSDT.
Change-Id: I22f9861452c2c222dd7a33bfeb02c63b026bf2f7
Signed-off-by: zhaojohn <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The DDR RFIM is a frequency shifting RFI mitigation feature required by
the Intel integrated Wi-Fi firmware(CNVi) for Meteor Lake. Please refer
to Intel technical white paper 640438_Intel_DDR_Mem_RFIM_Policy_Enable
once it is externally available. This change has backport changes from
commit hash 6f73a20 (soc/intel/alderlake: Move CnviDdrRfim property to
drivers) and provides the CNVi RFIM support for Meteor Lake.
BUG=b:248391777
TEST=Booted to OS on Rex. Looked the DDR_DVFS_RFI_CONFIG_PCU_REG
register at the offset 0x5A40 of Mchbar and verified the BIT0
(RFI_DISABLE bit) is 0.
Change-Id: I87110bc10b98a27a8f274680597b15a1df488824
Signed-off-by: zhaojohn <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67789
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
By convention 'fill_lb_xxx' is used.
Change-Id: I046016b3898308bb56b4ad6a5834ab942fdd50f2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69183
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of having callbacks into serial console code to set up the
coreboot table have the coreboot table code call IP specific code to get
serial information. This makes it easier to reuse the information as the
return value can be used in a different context (e.g. when filling in a
FDT).
This also removes boilerplate code to set up lb_console entries by
setting entry based on the type in struct lb_uart.
Change-Id: I6c08a88fb5fc035eb28d0becf19471c709c8043d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Update PsysPL2 and PsysPmax.
BUG=b:253542746
TEST=Make sure PsysPL2 and PsysPamx values set
properly (through debug output)
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I0ffad751e8a99b282a5d05563a60745ee09e892c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
* Add DPC related definitions which are defined in 7.9.14 of PCIe
6.0 spec.
* Add AER related definitions which are defined in 7.8.4 of PCIe
6.0 spec.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: Ifb6722c326ef69ef1bf3b1c2c1d5bc0cb29d7c12
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69106
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
This reverts commit 3bc9fbb496c7e1ae346c8d7e98d2bcabbbbe8673.
The patch that added hob_enhancedwarningloglib.h was marked as private
after the Jenkins run, so I didn't see and submit it before submitting
the patch that gets reverted by this commit. Temporary revert this patch
to fix the coreboot tree until the issue with the missing patch is
sorted out.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If56609dd2d91a70fe7e99ce86e0341f2b3fee3d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69229
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 059902882ce56502124375c9395ebe8b49640710.
A dependency of the previous patch that added the get_ewl_hob function
used by this patch was missing, so this patch needs to be temporary
reverted to revert the patch that breaks the build due to the missing
dependency.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Idb2fa27e75eede1648ddbf82c8bfbeeb2e9220a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69228
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Tested-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
|
|
Add an option on Atlas to enable IBECC (In Band Error Correction Code),
which is currently needed for endurance testing.
Test: start atlas mainboard with Linux. See in dmesg that
IBECC (EDAC igen6) driver is loaded. Inject a fake error via debugfs
and see in dmesg that Linux handles it.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I71ee2401136e2dc70b3164db6c99af03a3e1f346
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Add In Band Error Correction Code to Alderlake SOC's.
It's currently needed and tested for the Prodrive Atlas mainboard.
After enabling it in the UPD, FSP-M takes care of enabling IBECC.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I9cc2ed6defa1223aa422b9b0d8145f8f8b3dd12e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68756
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of having the config option PAYLOADS_NONE inside the choice of
payloads, make that a separate choice that enables the payload menu.
If the no_payload option is selected, this hides the other options
and keeps them out of the saved config file and config.h
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: I932c65630261a5b39809abf4dfbda5bf932c6684
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Also sort includes.
Change-Id: I7da9c672ee230dfaebd943247639b78d675957e4
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Add EWL (Enhanced Warning Log) driver which handles Intel EWL HOB
and prints EWL type 3 primarily associated with MRC training failures.
Change-Id: Ibd5b521bafd457505db4147c5d3fe41364a09045
Signed-off-by: Shelly Chang <Shelly_Chang@wiwynn.com>
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69145
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I8f949e9c881099c3723fca056e2c4732ca8b64cf
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69144
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
