| Age | Commit message (Collapse) | Author |
|---|
|
The existing code for setting Azalia configuration assumes that
the configuration bits are contiguous within a single byte and
can be set using a byte copy addressed into the lowest 2-bit
subfield.
The fix in Family 14 defines a union that can be addressed as a
byte to overlay the bit fields. Since the offset of the four
subfields is not necessarily fixed, change the code to initialize
each of the four subfields individually.
Change-Id: I1dff20bb8bd3e1bcd8b4e6b0537e20779d2a3521
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3544
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Copy a type cast from the other cases of the same switch statement
to eliminate compiler warning messages.
Change-Id: I8d0a88892f6a5f8e43227ab5f830041894b07f6a
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3543
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
On Dinar, H8SCM, and H8QGI, add <cpu/amd/amdfam15.h> as an
include to pick up the prototype definition of get_bus_conf().
Change-Id: Ie4887670ac52aa194745881362df19cd1d75773e
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3542
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change inserts a type cast to eliminate a compiler warning.
Change-Id: If223f61f1565caeadb1b7e0762975b1b2412eda5
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3541
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change replaces a redefinition of NULL with the standard
definition from <stddef.h> to eliminate a compiler redefinition
warning.
Change-Id: I441fa569f545c0efb00284b5ee58aa27cb6617ba
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3540
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change eliminates an unused variable that causes a build warning.
Change-Id: I02487c7dd80d458f562d7afe1827eefcc0fb678b
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3526
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This requires a new system agent binary (v6 / v11 on haswell).
Note that the existing system agent binaries are long time obsolete
and won't work with current coreboot, so this update is overdue.
Change-Id: I48d8649576ca84d2b85ab082ce06f3462e189059
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3568
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Static analysis often flags case statements that do not include
a terminating "break;" statement. Eclipse's CODAN is an example
of this. This changelist modifies amdlib.c to terminate
case statements with "break;".
Change-Id: I3d43acaf64e2e2d9717421cb547fec35e582cf8b
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3539
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change adds length modifiers to constant values to eliminate
compiler warning messages.
Change-Id: I032cb37cec788e2b5f79f5bbf9efc19a7892dc14
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3538
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change is mostly type casts to eliminate compile time
warnings. These specific changes are mostly cherry-picked from
AMD Family 14 code and, as such, contain artifacts copied over
from F14. For example, there are a number of UINT64 casts that
are commented out rather than removed. This is to maintain
consistency between AGESA versions. Ultimately, this is in
preparation for turning on warnings as errors for AMD Family 15
server parts.
Change-Id: Ic73d0b6ebab18d97015a9dd1130aff4e5e432fb7
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3525
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
For new systemagent v6 binaries.
Change-Id: I550533fd19c7c5592f3e3c9b514efe2750619c8f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3567
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Commit 039223a: gitmodules: Ignore 3rdparty in "diff family"
changed the behavior of our 3rdparty repository and disallowed
updates to the checked out hash. Instead of "ignore=all" we
want "ignore=dirty" to ignore local changes but allow changing
to the HEAD of the 3rdparty repo.
Change-Id: I66c35ad4fcfb0efb0ba611f67648a096a6de1479
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3566
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: If0963237806804a2a9d7f622c33013321379a04d
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/3536
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Change-Id: Ibc36988745cbc7ede2a00da376b5dd295014ffb1
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/3535
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
This reverts commit d358a506c4230950e34d783bd0187cd200d60691
http://review.coreboot.org/#/c/3514/ comments:
The pei_data version changed to 6, so new binaries are needed.
However, demand for new binary blob is not referenced with this commit nor is git submodules hash updated. Also the new binary blob almost doubles its size and no longer fits in the allocation sandybridge defines.
Change-Id: I84eb70517d5b9278c611fdfa587a71f6ca0f657f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3553
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The counted delay of 1ms was shorter than the time usb_poll() took
(~30ms observed). So with a given timeout of 100ms it actually took 3s.
We can lower the problem if we delay 10ms per loop iteration.
Change-Id: I6e084bdd05332111cc8adcd13493a5dfb4bc8b28
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3533
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The xHCI controller's MMIO space has a length of 64KiB not 4KiB.
Therefore, setting the xHCI BAR to 0xe8001000 worked the same like
setting it to 0xe8000000, as bit12 is reserved and ignored. This again
interfered with the MMIO space of the first EHCI controller and broke
S3 resume on Ivy Bridge.
AFAIK, the MRC ignores the setting of the xHCI BAR, anyway. So just drop
these lines.
Change-Id: I8af9c2ba34133f15636a9056fc8880b3b6ab95e0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3521
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
BIOS write protects 8 bytes of CMOS, which nvramtool can't cope with.
This makes initial installation harder, so just mark those as reserved
to work around the issue.
Change-Id: I210861dff8572e226a0f250556a3b811671ea8f2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3531
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Teach lpgcc to look in the in-coreboot tree directory structure, too.
Change-Id: I3809456d072ce2f91542b0edb3fd39f536298cc2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3530
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
6021 is Vortex86DX northbridge PCI device ID, not for Vortex86EX.
Change-Id: I9bea799c9033adbcfacc8ad47052280a32f9ee59
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3529
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Current build configuration always wants to include an Intel Management
Engine firmware (me.bin) on Sandy Bridge systems. However, we can have
a working coreboot without it, as long as the factory delivered ME
firmware is kept untouched in the flash ROM. So let the user decide if
a ME firmware will be included in the build.
Change-Id: I9a1cc29d4940ba22355eb9e653606e436f07e04c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3522
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
For iwave/iWRainbowG6 using intel/sch, MMCONF_BASE_ADDRESS was unused
and different from hardware setting. Change that to match hardware
programming.
Change-Id: I3324b7ea0e6f092206d4b6b791476d538e826657
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3507
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
abuild checks the path for toolchains prior to building a
mainboard. It didn't check xgcc/, which would be picked up
by the coreboot make, and fail to build when it shouldn't.
Change-Id: If0ca4238e8c57a6b015fdad623ccdbf237ef1ba6
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/3350
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This new tool called `ifdfake` just creates an empty Intel Firmware
Descriptor (IFD) and writes the IFD signature plus the section layout
given on the command line.
usage: ifdfake [(-b|-m|-g|-p) <start>:<end>]... <output file>
-b | --bios <start>:<end> BIOS region
-m | --me <start>:<end> Intel ME region
-g | --gbe <start>:<end> Gigabit Ethernet region
-p | --platform <start>:<end> Platform Data region
-h | --help print this help
<start> and <end> bounds are given in Bytes, the <end> bound is inclusive.
All regions must be multiples of 4K in size and 4K aligned.
The descriptor region always resides in the first 4K.
An IFD created with ifdfake won't work as a replacement for a real IFD.
Never try to flash such an IFD to your board!
The output of ifdfake can be utilized to build an image with just the
later added sections (like coreboot itself) being valid. The resulting
image can then be partially written to a machines flash ROM to just
update coreboot (i.e. the BIOS section).
Change-Id: I925b47cab5c6d490a79d684bdd7a7a45ac442640
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3523
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ife1c0a8597c2de04773899cdd87af6b6c630906a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3392
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On newer Intel systems, the flash ROM is shared between the host
processor (BIOS), it's Management Engine (ME) and an integrated ethernet
controller (GbE). The layout of the flash ROM (and other information) is
kept in the so called Intel Firmware Descriptor (IFD). If we only want
to build coreboot to update the BIOS section, all we need is the flash
layout.
This patch adds the option to specify the flash layout in the
mainboard's Kconfig, and thus, to build without the real IFD. However,
with such a build, one has to make sure that the IFD section on the
flash ROM won't be written over (nor any other section that hasn't been
included by coreboot). A patch to write selected sections of a flash ROM
with IFD has been sent to the flashrom mailing list [1].
[1] http://www.flashrom.org/pipermail/flashrom/2013-June/011083.html
Change-Id: Ia23e439a00a197fb54852263f8e206f16c3e8851
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3524
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There are no files to build left under AMD nortbridge/x/root_complex
directories. For some cases, even the Kconfig file was no longer sourced.
Remove all such references and empty files.
For devicetree.cb treat component paths with "/root_complex" in them valid
even when the directory does not exists. This is because AMD boards us this
dummy chip component as the root node in their devicetree.cb.
The generated devicetree file static.c remains unchanged.
Change-Id: I9278ebb50a83cebbf149b06afb5669899a8e4d0b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3434
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The IOMMU needs IRQs assigned. So add those.
Change-Id: Ic9f02e28aac593cddf7d222a8abb780a10572d32
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/3318
Tested-by: build bot (Jenkins)
Reviewed-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The IOMMU AGESA needs a reserved scratch space and it wants
to allocate the stuff for runtime. So provide a simple
allocator for 4 KB CBMEM page.
Change-Id: I53bdfcd2cd69f84fbfbc6edea53a051f516c05cc
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/3315
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
For IOMMU we need to allocate a 512 KB BAR in a non-standard
location. Use the standard allocator for that and limit the BAR
to 32-bits to be compatible with older systems.
Change-Id: I44414ce6b264b7f1c086a9b1c7ea275a0830205e
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3314
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
LynxPoint LP has only EHCI controller #1.
Change EHCI #2 to different BAR from EHCI #1.
Even if the ECHI controllers are not to be addressed, it is bad idea
to set two different devices to claim the same PCI memory cycles.
Change-Id: I95c59fb9d5f09afd152872e9bc0418dc67e4aeb2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3472
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Also, add pretty printing of Westmere's DMI registers (tested on my t410s
by staring at non-zero output values :)
Apparently Nehalem does not have a MEMBAR? But there are some
documented memory controller control registers in PCI configuration
space... left out for now.
The PCIEXBAR is not documented publicly AFAICT, but there is
a similar register on a device on bus 0xFF. phcoder might know more...
Change-Id: I5faadb6e4f701728f5290276c02809b4993bd86d
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/3505
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In commit Rudolf Marek discovered, that it is not uniformly written. As
»ASL names are not case-sensitive and will be converted to upper case.« [2]
this change does not have any functional change.
The following command was used to create this patch.
$ git grep -l 'package()' src/mainboard | xargs sed -i 's,package(),Package(),'
[1] http://review.coreboot.org/#/c/3318/
[2] http://www.acpi.info/spec40a.htm
(18.2.1 ASL Names)
Change-Id: I1784dbc50936a1ef9d4376209a3c324ef1fb85cf
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3516
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This patch allows the use of migrated CAR_GLOBAL variables from
the very beginning of ramstage. Without the patch, CAR_GLOBALS were
not available until northbridge set_resources().
Change-Id: Ifd4ab2ed52e07dcbe8c77e2e460dc483323e93c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3513
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Non-S3 resume paths of sandy/ivybridge call cbmem_initialize()
more than once. Doing car_migrate_variables() more than twice caused
at least loss of some lines in CBMEM console.
Change-Id: Idd14aba9384984aa3a7d38937a4b3572aa5dc088
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3512
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: I60675a357f9db430ebb59b17be6d8c92a9cadf43
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3511
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This commit was tested on qemu with and without CONFIG_DYNAMIC_CBMEM
by running cmbmem -c once booted. The qemu command that was used was:
qemu-system-i386 -bios ./build/coreboot.rom -serial stdio -hda ../virt/parabola.img
Note that using CONFIG_RELOCATABLE_RAMSTAGE make it fails like that:
Loading image.
CBFS: Decompressing stage fallback/coreboot_ram @ 0x3ffbefc0 (184400 bytes)
Loading module at 3ffbf000 with entry 3ffbf000. filesize: 0x18db8 memsize: 0x2c050
Processing 1703 relocs with adjust value of 0x3ffbe000
FATAL: Essential component is missing.
However without CONFIG_RELOCATABLE_RAMSTAGE set it boots fine.
Change-Id: I633a8c3832eee4e8bed244940fdc370b98dd26f0
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3504
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
In case we are going to use this in future designs.
BUG=none
TEST=none
BRANCH=none
Change-Id: I750addf10e4fe6f8240f8c8262253f8af7027e29
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/55844
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3515
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
src/lib/cbmem.c is for the static cbmem.
Thanks to adurbin for the Makefile.inc pointer and code on #coreboot IRC channel on freenode:
<adurbin> no. if you have CONFIG_DYNAMIC_CBMEM then cbmem.c shouldn't be compiled
[...]
<adurbin> +ifeq ($(CONFIG_EARLY_CBMEM_INIT),y)
<adurbin> +ifneq ($(CONFIG_DYNAMIC_CBMEM),y) romstage-$(CONFIG_EARLY_CBMEM_INIT) += cbmem.c
<adurbin> +endif
<adurbin> +endif
Without that fix we have:
src/lib/cbmem.c:58:43: error: no previous prototype for 'get_cbmem_toc' [-Werror=missing-prototypes]
src/lib/cbmem.c:76:6: error: no previous prototype for 'cbmem_init' [-Werror=missing-prototypes]
src/lib/cbmem.c:107:5: error: no previous prototype for 'cbmem_reinit' [-Werror=missing-prototypes]
This commit was tested on qemu-i440fx with the following commit:
qemu-i440fx: Make it compile with CONFIG_DYNAMIC_CBMEM
( http://review.coreboot.org/#/c/3504/ ).
Change-Id: I98636aad4bb4b954f3ed3957df67c77f3615964a
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3503
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
Change EHCI #2 to different BAR from EHCI #1.
Even if the ECHI controllers are not to be addressed, it is bad idea
to set two different devices to claim the same PCI memory cycles.
Change-Id: Ib6f7cfac5acf3f8170508547d1584af90273e8c1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3471
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
|
|
Change-Id: I2e3fd58404c48e863a3a1b255337fb397086651b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3506
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I74de250c69a57109362be1b2f00c0b4aa24a64e8
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3473
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Location is hard-coded right now, which isn't optimal.
It must be chip erase block aligned, which might fail on some flash chips
(it's 64k aligned which should work for most cases).
Change-Id: I6fe0607948c5fab04b9ed565a93e00b96bf44986
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3497
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Collect early timestamps in T60's romstage like some newer boards do.
This should also work on X60s (and other ICH7 based systems with
EARLY_CBMEM_INIT).
Change-Id: I3b2872dd7423f3379ff3b68ad999523ec35fc08e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3499
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Upgrade the ICH7 bootblock to store an initial timestamp like we do it
since Sandy Brigde. I've checked the datasheets for the used scratchpad
registers and grepped for their usage. I'm pretty sure that they aren't
used on any ICH7 based board (for anything before the usual S3-resume
indication).
Change-Id: I28a9b90d3e6f6401a8114ecd240554a5dddc0eb5
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3498
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Ditch unused fb*.h files.
Rename init.c (name is _way_ to generic) to bochs.c.
Add proper bochs dispi interface detection and mode setup.
Hook up coreboot framebuffer table initialization.
Change-Id: I7154b1593902e7d42606b64819217872eee10683
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3500
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
src/lib/edid.c:1177: error: ‘y’ may be used uninitialized in this function
Warning is bogus, but seems my gcc (4.4.7 as shipped by RHEL-6)
isn't clever enougth to figure this on its own. So help a bit
by explicitly initializing the variable.
Change-Id: Ia9f966c9c0a6bd92a9f41f1a4a3c8e49f258be37
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3501
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
We can't read the drives signature before it's ready, i.e. spun up.
So set the timeout to the standard 30s. Also put a notice on the
console, so the user knows why the signature reading failed.
Change-Id: I2148258f9b0eb950b71544dafd95776ae70afac8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3493
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The SPI logical device on the W83627DHG uses the second i/o port
register pair but not the first one. So we have to also set `io1`
(the second io_info struct) and not `io0` in the pnp_info structure.
Setting the PNP_IO1 flag without a mask in `io1` caused coreboot to
hang in pnp_enable_devices() until commit aeead274 which added a
check for an unset mask.
Change-Id: I027d279b4641fecd88afb14d40fbe1c0bfbf81bb
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3391
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I8371764e3f2d16a3a776beb1c064f461b20a4262
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3496
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
I was unable to find documentation that said what mode numbers correspond
to what functionality, so I translated over what U-Boot does.
Change-Id: I34fab0f024fa2322d6bb66106aed75224e67354d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3489
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
All 3 boards with AGESA_HUDSON had HAVE_HARD_RESET with the reset.c
file already placed under southbridge/.
All 15 boards with CIMX_SBx00 had HAVE_HARD_RESET with functionally
identical reset.c file under mainboard/. Move those files under
respective southbridge/.
Change-Id: Icfda51527ee62e578067a7fc9dcf60bc9860b269
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3486
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Confusingly, romstage compiled in different copy of soft_reset()
than ramstage. Use source in reset.c for both.
Change-Id: I2e4b6d1b89c859c7cf5d9e9c8f7748b43d369775
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3487
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The chip component is unconditionally selected for the mainboard
so these uses are superfluous.
Change-Id: I84b053ab47f7b1f68e88d968cf305e24bc95f4da
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3485
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
CONFIG_HUDSON_XHCI_ENABLE will control the XHCI flags in the
amd/parmer and asus/f2a85-m mainboards. The XHCI ports on
amd/thatcher are not wired to USB jacks so always disable the flags.
This was tested on amd/parmer using a USB 3.0 thumbdrive.
Change-Id: I596b040fec30882d8d4dee34ab9f866dc1f8896b
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3465
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
To have USB 3.0 support the XHCI controller needs to be enabled
and the xhci.bin firmware needs to be added to CBFS.
Change-Id: I0b641b30b67163b7dc73ee7ae67efe678e11c000
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3464
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
After removing the enter()/exit() functions for configuration mode,
most wrappers for our standard PnP functions just call the underlying
default implementation.
Remove those with a little cocci:
@ op_match @
identifier op;
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
type device_t;
identifier dev;
@@
static void op(device_t dev) { pnp_op(dev); }
@@
identifier op_match.op;
@@
-op(...) {...}
/* Three rules to match the alignment, hmmp... */
@@
identifier op_match.op, op_match.pnp_op;
identifier ops;
@@
struct device_operations ops = {
- .set_resources = op,
+ .set_resources = pnp_op,
};
@@
identifier op_match.op, op_match.pnp_op;
identifier ops;
@@
struct device_operations ops = {
- .enable_resources = op,
+ .enable_resources = pnp_op,
};
@@
identifier op_match.op, op_match.pnp_op;
identifier ops;
@@
struct device_operations ops = {
- .enable = op,
+ .enable = pnp_op,
};
Change-Id: Idc0e52c7e3600a01f3b6a4e17763557b271b481e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3483
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Find all the (ramstage) implementations of enter()/exit() functions
for the configuration state, register and call them through the new
struct pnp_mode_ops. As our standard PnP functions are aware of the
pnp_mode_ops, it's not necessary to call enter()/exit() around them
anymore.
Patch generated with the cocci below. It's not perfect. The movement
of the enter()/exit() calls is somehow fragile. So I checked the
remaining calls for sense, and changed some empty lines. Also a
duplicate insertion of pnp_conf_mode_ops had to be removed.
/* Try to find enter and exit functions by their outb() structure and
their usage around calls to our standard pnp functions: */
@ enter_match @
identifier enter;
identifier dev;
type device_t;
@@
void enter(device_t dev)
{
<...
outb(..., dev->path.pnp.port);
...>
}
@ exit_match @
identifier exit;
identifier dev;
type device_t;
@@
void exit(device_t dev)
{
<...
outb(..., dev->path.pnp.port);
...>
}
@ pnp_match @
identifier op;
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
identifier enter_match.enter, exit_match.exit;
type device_t;
identifier dev;
@@
void op(device_t dev)
{
...
enter(dev);
...
pnp_op(dev);
...
exit(dev);
...
}
/* Now add enter/exit to a pnp_mode_ops structure: */
@ depends on pnp_match @
identifier enter_match.enter;
identifier exit_match.exit;
identifier ops;
@@
+static const struct pnp_mode_ops pnp_conf_mode_ops = {
+ .enter_conf_mode = enter,
+ .exit_conf_mode = exit,
+};
+
struct device_operations ops = {
...,
+ .ops_pnp_mode = &pnp_conf_mode_ops,
};
/* Match against the new structure as we change the code and the above
matches might not work anymore: */
@ mode_match @
identifier enter, exit, ops;
@@
struct pnp_mode_ops ops = {
.enter_conf_mode = enter,
.exit_conf_mode = exit,
};
/* Replace enter()/enter() calls with new standard calls (e.g.
pnp_enter_conf_mode()): */
@@
identifier mode_match.enter;
expression e;
@@
-enter(e)
+pnp_enter_conf_mode(e)
@@
identifier mode_match.exit;
expression e;
@@
-exit(e)
+pnp_exit_conf_mode(e)
/* If there are calls to standard PnP functions, (re)move the
enter()/exit() calls around them: */
@@
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
expression e;
@@
-pnp_enter_conf_mode(e);
pnp_op(e);
+pnp_enter_conf_mode(e);
...
pnp_exit_conf_mode(e);
@@
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
expression e;
@@
pnp_enter_conf_mode(e);
...
+pnp_exit_conf_mode(e);
pnp_op(e);
-pnp_exit_conf_mode(e);
@@
expression e;
@@
-pnp_enter_conf_mode(e);
-pnp_exit_conf_mode(e);
Change-Id: I5c04b0c6a8f01a30bc25fe195797c02e75b6c276
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3482
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Many super i/o chips only answer to PnP requests if they are in a
configuration state (sometimes also called ext func mode). To cope with
that, the code of many chips implements its own version of our default
PnP functions like pnp_set_resource(), pnp_enable_resource() etc.
To avoid this code duplication, this patch extends our PnP device
interface with optional functions to enter and exit configuration mode.
Change-Id: I9b7662a0db70ede93276764fa15020f251eb46bd
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3481
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The current default implementation of pnp_enable() only disables devices
- if set so in the devicetree - but does not enable them. Enablement takes
place in pnp_enable_resources(). Yet, many PnP chips implement their own
version of pnp_enable() which also enables devices if set in the devicetree.
It's arguable, if enabling those devices makes sense, before they get
resources assigned. Maybe we can't write the resource registers if not,
who knows? The least we can do is providing a common implementation for
this behavior, and get rid of some code duplication.
Used the following cocci:
@@
expression e;
@@
+pnp_alt_enable(e);
-pnp_set_logical_device(e);
(
-pnp_set_enable(e, !!e->enabled);
|
-(e->enabled) ? pnp_set_enable(e, 1) : pnp_set_enable(e, 0);
|
-if (e->enabled) { pnp_set_enable(e, 1); }
-else { pnp_set_enable(e, 0); }
)
Change-Id: I8d695e8fcd3cf8b847b1aa99326b51a554700bc4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3480
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
A timeout while waiting for a device' signature has shown that our
error path wasn't correct. The shutdown of the ports command engine
always timed out. Fix that by waiting for FR (FIS Receive Running)
to be cleared independently from CR (Command List Running) and after
clearing FRE (FIS Receive Enable).
Change-Id: I50edf426ef0241424456f1489a7fc86a2cfc5753
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3494
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
They were hard-coded to be copied from 3rdparty/ which isn't always
the right choice.
Since the defaults stay the same, this should be compatible.
Change-Id: If2173bef86ad1fcf2335e13472ea8ca41eb41f3d
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3453
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Most PnP drivers align the initialization of their `device_operations`
with spaces. Unify this, so next autogenerated patches always match the
alignment.
Change-Id: I3f6baef6c8bb294c136354754125ea88c07a61a1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3479
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I0d499027ffb175638cba0a9830d6ec2041a139db
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3488
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add support for the new q35 chipset emulation
added in qemu 1.4.
Change-Id: Iabfaa1310dc7b54c9d224635addebdfafe1fbfaf
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3430
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ic83f55d01b29b43028e3b363749d64b927db5489
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3492
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
So the pci allocation code knows where memory is and doesn't
try map pci devices there. We also don't have to check for
overlaps between pci hole and memory then.
Change-Id: I5eaea0e4d21210719685860fa1f16ca7b2137cde
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3491
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
memory reference
An uninitialized RAM value was used to select an MSR because a $ was forgotten
in front of `CPU_DM_CONFIG0`. It should be the constant value 0x1800, corresponding
to CPU_DM_CONFIG0 MSR defined in `src/include/cpu/amd/lxdef.h`.
Change-Id: Id53ca98b06cc4a9b55916fd8db23904f98008d45
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://review.coreboot.org/3478
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
The original lines had contradicting comment and code.
This change follows the code and sets MASTER bit too.
Change-Id: Id2886bfc107612530f0e9747e5d49a9740fb8532
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3466
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Prepare tree for adding q35 support:
Move emulation/qemu-x86 to emulation/qemu-i440fx.
Rename some stuff to include 'i440fx'.
Change-Id: Ib8c58175c5734cfcda1b22404ef52c09d38f0462
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3429
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
With this patch, output on usbdebug also includes the section of
MTRR setups for every CPU. This makes usbdebug output almost identical
with that of serial port and CBMEM console.
Tested with model_206ax. Also tested previously on model_f2x which does
not have these disable/enable calls in model_f2x_init() without detected issues.
Change-Id: Idfd0e93439907b17255633658195d698feab3895
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3423
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
IDs were leftovers from bd82x6x.
Change-Id: I4ab6062929d346d7f000ce8c0b8c97490bb2b154
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3463
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
This patch provides the correct SD controller timings for
the Family16 device. It also will remove the SD controller
from PCI space when device 0:14.7 is set to off in devicetree.
This was tested on a AMD Parmer board and a AMD G-series SOC
reference board. The settings were found in the AMD
Hudson2 RRG and family16 BKGD.
Change-Id: I6d7e7997ddc39802ab75dc8a211ed29f028c0471
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3348
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Well, it turned out to be more as some gaps ;)
but we finally have xHCI running. It's well tested against a QM77 Ivy
Bridge board.
We have no SuperSpeed support (yet). On Ivy Bridge, SuperSpeed is not
advertised and USB 3 devices will just work at HighSpeed.
There are still some bit fields in xhci_private.h, so this might need
little more work to run on ARM.
Change-Id: I7a2cb3f226d24573659142565db38b13acdc218c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3452
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is mostly a rewrite, don't even try to read a diff.
Tested with an internal rate matching hub on a QM77 board and three hubs
integrated into DELL monitors.
Change-Id: Ib12fa2aa90af4e0f37143d2ed92c4a1705b6d774
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3451
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The current drivers for external usb hubs and root hubs all follow
the same pattern. Before adding another one with 90% of the same code,
extract the common parts and rewrite them with a simple interface.
This also adds debouncing of new attachments. Current drivers just
waited 100ms before they reset the device. However, we should check
if the device becomes disconnected and reconnected during this period.
Porting of the current hub drivers will take place in separate
commits (when I have time to test the older HCIs).
Change-Id: I0c0ce0ac1b1cc51fb4cd009b3f9fcd1b9d2ba8fe
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3450
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Read bInterval from endpoint descriptors and store it in our endpoint_t
struct. The interval is encoded dependently on the device' speed and the
endpoint's type. Therefore, it will be normalized to the binary logarithm
of the number of microframes, i.e.
t = 125us * 2^interval
The interval attribute will be used in the xHCI driver.
Change-Id: I65a8eda6145faf34666800789f0292e640a8141b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3449
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
xHCI requires special treatment of set_address since it determines
the device number itself (instead of the driver, as with the other
controllers). The controller also wants to validate a chosen device
configuration and we need to setup additional structures for the
device and the endpoints.
Therefore, we add three functions to the hci_t structure, namely:
set_address()
finish_device_config()
destroy_device()
Current implementation for the Set Address request moved into
generic_set_address() which is set_address() for the UHCI, OCHI and
EHCI drivers. The latter two are only provided as hooks for the xHCI
driver.
The Set Configuration request is moved after endpoint enumeration.
For all other controller drivers nothing changes, as there is no other
device communication between the lines where the set_configuration()
call moved.
Change-Id: I6127627b9367ef573aa1a1525782bc1304ea350d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3447
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
These values are already used in this usb stack.
Change-Id: If96f1dc2b67fbc13dfc4ae2d84e8f9945aa03163
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3448
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
During device initialization, skip any non-endpoint descriptor before
reading the endpoint descriptors. By now, only HID descriptors were
skipped.
Change-Id: I190f3ae44b864aa71d5f32c3738097cf8f33a61b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
e4e8e090fa36cb3a098e1ddf0ea44c796c140572 does add support for QM57,
but there are many more that should work with that code(?).
Does not explode on...
CPU: Processor Type: 0, Family 6, Model 25, Stepping 2
Northbridge: 8086:0044 (1st generation (Westmere family) Core Processor)
Southbridge: 8086:3b0f (QS57)
Change-Id: I85e15ba45678a5bd635415a7a8d69c05bff8f7ef
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/3321
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
In function OemAgesaSaveMtrr of 'src/cpu/amd/agesa/s3_resume.c',
there are many code like this:
msr_data = rdmsr(0x258);
flash->write(flash, nvram_pos, 4, &msr_data.lo);
nvram_pos += 4;
flash->write(flash, nvram_pos, 4, &msr_data.hi);
nvram_pos += 4;
Add a function write_mtrr to do this.
Change-Id: Id6464e637db1758b07ac2d79d3be1375a8d49651
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3410
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This issue can be reproduced in Linux by the following steps:
1) use pm-suspend to suspend.
2) use USB keyboard to wake up.
3) use pm-suspend to suspend. FAIL To SUSPEND.
The cause of this issue is:
USB devices use bit 11(0x0b) of GP0_STS represents S3 wake up event,
but this bit is not clear after wake up. So OS thinks there is a
wake up signal and wake up immediately.
In this patch, I add AcpiGpe0Blk using MMIO access and write 1
on bit 11. Write 1 to clear as spec says.
I have tested on Thatcher
The same change was done for AMD Parmer in commit »AMD Parmer:
fix issue 'S3 fails to suspend after wake up from USB keyboard'
(03901124) [1].
[1] http://review.coreboot.org/#/c/3347/
(Change-Id: Iec3078bf29de99683e7cd3ef4e178fbeb4dc09c1)
Change-Id: Iaef39237497ef896d0f186e8f5522222c0ce6cb7
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3374
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I21182eae1d389790c330f27e6a830d91c3ee4eb6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3433
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Change-Id: I7ecc394b1e5bc0b8b85a8afac22efc0befe2d36a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3395
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This reverts commit 0210119b4b95e84f954cfd6dc11aafbc187421af
Change-Id: I5be3f2a54394c592650a0dcd671e4a72ae796cb2
Reviewed-on: http://review.coreboot.org/3443
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: If56f2cacc5f1b2ef9c7b6aea508d458a43dd1309
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3397
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Until ME boots (which takes seconds on X201) the reported temperature
is 128 °C which triggers Linux overheat alarm which shuts down.
Pretend temperature is 40°C until ME boots.
Change-Id: Ia49fa03c6eb27f539a23711f2c8ebfde72b1dc18
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3404
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On X201 to enable EHCI debug you need to go through EC if USB power is
disabled so we need to inclue ec.c.
Change-Id: I8f8b7de639ecaebceaa53cd338136befaeec8214
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3405
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Enable UMTS on Lenovo X60 and X201.
Enable radios if no options are available.
Enable dock on Lenovo X201.
Based on my X201 branch.
Change-Id: I6e8d3bbd6a6b1a8e59473dd5cc8125a1583d75df
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add a struct for referencing UART registers. The layout is quite
strange on this chip, as the entire register space can take on three
different meanings depending on the line control settings (in the LCR
register) And to make things more confusing, some offsets reference
different registers depending on if a read or a write operation is
used.
Change-Id: Ie62af9c0e0edafd01b81686a0fe5c5c1d4fa06c4
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This ancient board with Intel e7505 invalidates cache while it does HW
scrubbing for ECC in romstage. This breaks usbdebug console and prevents
system from booting.
If both EARLY_CONSOLE and USBDEBUG are selected, skip ECC scrubbing under
these rare conditions to boot system.
Change-Id: I6cb43bf69af54119f4a582dcaf498dd941d4c62d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3385
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In case with EARLY_CONSOLE, this printk is called before any other
console is configured to transmit data. This outputs garbage on
CONSOLE_SERIAL as baudrate is not yet programmed.
For case without EARLY_CONSOLE, the order in which different console
drivers initialize is obscure. Might sometimes work properly.
Change-Id: I3792161e0a6dc17e17262048cc9136044dd69dc5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3384
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Add comment how one can debug the usbdebug hardware init.
Do not send printk's to usbdebug console when one is debugging
the usbdebug console initialisation itself.
Change-Id: I21a285cb31cf64e853bc626f8b6a617bc5a8be19
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3382
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Setting IRQ delivery to FSB got lost in the rebase process
for commit e6143531.
I captured following error on dmesg and this patch fixes it for
i82801dx.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 2) ...
....... failed.
...trying to set up timer as Virtual Wire IRQ...
..... works.
Change-Id: I0768976cc6b0deab213ad9bd4771e0f278de634c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3371
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This is spkmodem receiver counterpart.
Change-Id: Id27d32608502029fb6fcc8154f508811bf5ca77b
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3411
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Mapping is as follows: bit 15 corresponds to GPIO15 ... bit 0 corresponds to
GPIO0.
Change-Id: I661ce56d9373887270ba3c0518892fbbe6d9de7c
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/3436
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Currently in Intel BD82x6x southbridge’s `Makefile.inc` the
file `usb_debug.c` is added twice to the build.
This was introduced in
commit 4063ede3fb571110c3e65c321049cc2687cc54fa
Author: Ronald G. Minnich <rminnich@google.com>
Date: Mon Feb 4 20:31:51 2013 -0800
bd82x6x: Fix compiling with USB debug port support
Reviewed-on: http://review.coreboot.org/2784
but was unneeded because it had been already added in
the following commit.
commit 4141993536039e0d45caeacb745a89d388f0724b
Author: Sven Schnelle <svens@stackframe.org>
Date: Sat Jul 28 08:52:44 2012 +0200
bd82x6x: Fix CONFIG_USBDEBUG
Reviewed-on: http://review.coreboot.org/1376
Therefore basically revert that hunk.
There is no policy on how to order these additions, so leave
it to a possible separate commit, unifying this.
Kyösti Mälkki suspects that these additions were meant for
the Intel Lynx Point [1].
[1] http://review.coreboot.org/#/c/3424/
Change-Id: Iaa8de6fcc0d6f3a0a92a28fcb603d7777aa8b24c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3425
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Fix obvious mistake in cycle that displays GPI status
I hope i found all duplicates of it.
Change-Id: Ic21ff3ecab85953463e5c23daf808dd5edc82ff8
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/3435
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The current method will treat hex values as 0 and would calculate the wrong
size. This change switches back to an earlier method which used shell syntax
to add the offset and size.
Change-Id: I9fb2d9b323f113cc56a5ad2e38b47d2d22084f08
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3432
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
