| Age | Commit message (Collapse) | Author |
|---|
|
There are multiple different devicetree setting formats for graphics
panel settings present in coreboot. Replace the ones for the platforms
that already have (mostly) unified gma/graphics setup code by a unified
struct in the gma driver. Hook it up in HSW, BDW, SKL, and APL and adapt
the devicetrees accordingly.
Always ensure that values don't overflow by applying appropriate masks.
The remaining platforms implementing panel settings (GM45, i945, ILK and
SNB) can be migrated later after unifying their gma/graphics setup code.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I445defe01d5fbf9a69cf05cf1b5bd6c7c2c1725e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
For easier review of the switch to a new register struct in the
follow-up change, the panel delay times get converted from destination
register raw format to milliseconds representation in this change.
Formula for conversion of power cycle delay:
gpu_panel_power_cycle_delay_ms =
(gpu_panel_power_cycle_delay - 1) * 100
Formula for all others:
gpu_panel_power_X_delay_ms = gpu_panel_power_X_delay / 10
The register names gain a suffix `_ms` and calculation of the
destination register raw values gets done in gma code now.
Change-Id: Idf8e076dac2b3048a63a0109263a6e7899f07230
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
SoC will transmit the EoTp (End of Transmission packet) when
MIPI_DSI_MODE_EOT_PACKET flag is set.
Enabling EoTp will make the line time larger, so the hfp and
hbp should be reduced to keep line time.
BUG=b:168728787
BRANCH=kukui
TEST=Display is normal on Kukui
Signed-off-by: Shaoming Chen <shaoming.chen@mediatek.corp-partner.google.com>
Change-Id: Ifadd0def13cc264e9d39ab9c981fbdc996396bfa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Some bridge chip or panel requires dsi signal output before dsi
receiver works.
BUG=b:168728787
BRANCH=kukui
TEST=Display is normal on Kukui
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Change-Id: I3bded27087490f32ee233e615cfad1fd05fb582d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add the stdint.h header, and drop the GLIBC section from amdfwtool.h to build this tool on FreeBSD as well as Linux.
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: I295fd308b0f5e2902931f02c9455823a614976de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48977
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I1e63a419db92642df6b7956050c39540c2ae11d6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48781
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9d500be609d61ccf234260216bd5aae3f78e91a8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48802
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The flash controller driver can be shared among mt8173 and mt819x.
TEST=boot to kernel on Asurada
boot to kernel on Hana (w/o BL31)
Change-Id: I4e5213563189336496122a0f2d8077b3e5245314
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: If200f4dcef0b1d0b7e901d4ae6e667b1f75156f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I317451e41774e983c07566dc71c7ba8833c7f55e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
To get better PI linearity, perform 8 phase calibration to do
MCK 0/180/45 training and select the best PI settings.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: Ib4ccaa8d43b8382cbc64cf82de86ad1ac16cb89a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I08326cd1e6f7415d3a91d1591678e1b2c52c6781
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
which select INTEL_GMA_ACPI. Rework brightness level includes and
platform-level asl files to avoid duplicate device definition for GFX0.
Include gfx.asl for Skylake/Kabylake, since all other soc/intel/common
platforms already do. Adjust mb/51nb/x210 to prevent device redefinition.
Some OSes (e.g. Windows, MacOS) require/prefer the ACPI device for
the IGD to exist, even if ACPI brightness controls are not utilized.
This change adds a GFX0 ACPI device for all boards whose platforms
select INTEL_GMA_ACPI without requiring non-functional brightness
controls to be added at the board level.
Change-Id: Ie71bd5fc7acd926b7ce7da17fbc108670fd453e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Adjust platform-level includes as needed.
Change-Id: I376349ccddb95c166f0836ec1273bb8252c7c155
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
eint event mask register is used to mask eint wakeup source on mt8192.
All wakeup sources are masked by default. Since most MediaTek SoCs do
not have this design, we can't modify the kernel eint upstream driver to
solve the issue 'Can't wake using power button (cros_ec) or touchpad'.
So we add a driver here to unmask all wakeup sources.
BUG=b:169024614
Signed-off-by: G.Pangao <gtk_pangao@mediatek.com>
Change-Id: I8ee80bf8302c146e09b74e9f6c6c49f501d7c1c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46409
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Extract the architecture (-a) and package (-p) options into a
new variable (ARCH) to simplify the construction of BUILD_STR.
Test: build/boot various boards w/Tianocore payload
Change-Id: I490d48428ac56d613d0b704700dfcf4ebfb2d245
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48942
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the right register values for backlight control to CNL's Kconfig.
To make iasl happy about the reversed register order, split the field.
Change-Id: I05a06cc42397c202df9c9a1ebc72fb10da3b10ec
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Replace the mainboard-specific code for "POST complete" signalling with
devicetree entries for using the newly introduced IPMI driver
functionality.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Change-Id: I3441c2a971cfb564b34b3a419beceb949fe295b1
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Configure the "POST complete" gpio in the devicetree for the BMC/IPMI
driver and set the pad's initial value to 0 since the signal is active-
high and shall be set by the IPMI/BMC driver.
Also add the pad to early gpio config, since it is expected to have an
external pull-up like X11SSM-F, which is wrong and would confuse the BMC.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Change-Id: If344b2271bfc8d50b8b64847109818f96f2abbcb
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Configure the "POST complete" gpio in the devicetree for the BMC/IPMI
driver.
Also add the pad to early gpio config, since it has an external pull-up,
which is wrong and would confuse the BMC. Set the pad's initial value to
zero since the "POST complete" signal is active-high and shall be set by
the IPMI/BMC driver.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I6409b2aca90585e44ee5d32df0ae73b259443f32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set `bmc_jumper_gpio` to the JPB1 gpio to enable/disable BMC/IPMI
according to its value.
Test: Boot with jumper set to each enabled and disabled and check debug
log if IPMI gets enabled/disabled accordingly.
Tested successfully.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8581556d915cbad2c743a79db273479ba55798fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Some server boards like OCP Tiogapass and X11-LGA1151 boards use a gpio
for signalling "POST complete" to BMC/IPMI. Add a new driver devicetree
option to set the gpio and configure a callback that pulls the gpio low
right before jumping to the payload.
Test: Check that sensor readings appear in BMC web interface when the
payload gets executed.
Successfully tested on Supermicro X11SSM-F with CB:48097, X11SSH-TF with
CB:48711 and OCP DeltaLake with CB:48672.
Change-Id: I34764858be9c7f7f1110ce885fa056591164f148
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Some boards, like the Supermicro X11SSM-F, have a jumper for enabling or
disabling the BMC and IPMI. Add a new devicetree driver option to set
the GPIO used for the jumper and enable or disable IPMI according to its
value.
This gets used in a follow-up change by Supermicro X11SSM-F.
Test: Boot with jumper set to each enabled and disabled and check debug
log if IPMI gets enabled/disabled accordingly.
Successfully tested on Supermicro X11SSM-F with CB:48095.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Icde3232843a7138797a4b106560f170972edeb9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change adds the required gpio operations struct to soc/common gpio
code and hooks them up in all socs currently using the gpio block code,
except DNV-NS, which is handled in a separate change.
Also, add the gpio device to existing chipset devicetrees.
Successfully tested on Supermicro X11SSM-F with CB:48097, X11SSH-TF with
CB:48711 and OCP DeltaLake with CB:48672.
Change-Id: I81dbbf5397b28ffa7537465c53332779245b39f6
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48583
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 5bb5c43b936f0bb01e08a71df1865343d7be9b88.
Reason for revert: Build bot fails.
Change-Id: I8f022514351b37be135d10ef8486e4aa5fd6361b
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48980
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the mask for the power cycle delay from 0xff to 0x1f, to
represent the actual maximum value according to Intel graphics PRM for
Haswell, Volume 2c and Intel graphics PRM for Broadwell, Volume 2c.
Change-Id: Ib187f1ca6474325475e5ae4cc1b2ffbce12f10bf
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48957
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow TGL chipset.cb to add alias for TCSS and USB ports.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I803dad0af09b26a55ffb767826ba79cf61de04ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48793
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Kaby Lake PCH can have up to 24 PCIe root ports. Thus, add 4 missing
root ports to the chipset devicetree.
Change-Id: I443fb736873d47f1b6fe7718a10e1bb4ae5df2a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48947
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On commit 64c03e3c ("mb/google/poppy: Fix race condition in acpi"),
we introduced a new Power Resource common to all the camera modules,
in order to resolve a race condition when both modules were in use
(e.g. during startup).
The nautilus variant also used the Power Supply I2C2.PMIC.OVTH, which
requires the new common PR, but the new dependency was not added.
Depend on the new Camera Common Power Resource.
Fixes: 64c03e3c ("mb/google/poppy: Fix race condition in acpi")
BRANCH=poppy
BUG=b:174941580
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Change-Id: Ifa6c70b7c02aec0112189eca573e76e53175d70d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: shkim <sh_.kim@samsung.com>
|
|
Initiate peripheral buses based on latest schematic.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a828bfb3ba4ee9a9b41cd4e83701672e5ef85bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
More recent platforms (Cooperlake) need bigger sizes.
Change-Id: Ia3e81d051a03b54233eef6ccdc4740c1a709be40
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch fixes the build with an external (coreboot) toolchain. When
the toolchain is not under util/crossgcc/xgcc, setting XGCCPATH to
/path/to/toolchain results in the error:
toolchain.inc:169: The coreboot toolchain version of iasl '<date>' was
not found
The reason is that the xcompile script incorrectly assumes XGCCPATH to
have a trailing slash.
Change-Id: Ifcc4bd2b081fa3603420dc0a8cab3b47967ebc65
Signed-off-by: Michele Guerini Rocco <rnhmjoj@inventati.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I50d5aebaf249ab7292fad7a0046099239c8b403c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
We don't know exactly for what the GMM PCI device is used for or how it
is used. Thus, remove it to fallback to default-disable.
Change-Id: I4b8b33b16527cbcc21168b995cbfdb54a2fa3cac
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
All known on-chip PCI devices are documented in chipset devicetree now
and default to disabled. There is no need to keep disabled PCI devices
in the mainboard's devicetree. Thus, remove them.
Change-Id: I7c537bba75d66badf854f9e7b6799303a7af018e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Add the register PNP_IO4, which will be used by IT5570E in CB:48894.
Change-Id: Ic820295247323f546d4c48ed17cfa4eab3dc5e92
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48924
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Introduce a new device `gpio` that is going to be used for generic
abstraction of gpio operations in the devicetree.
The general idea behind this is that every chip can have gpios that
shall be accessible in a very generic way by any driver through the
devicetree.
The chip that implements the chip-specific gpio operations has to assign
them to the generic device operations struct, which then gets assigned
to the gpio device during device probing. See CB:48583 for how this gets
done for the SoCs using intelblocks/gpio.
The gpio device then can be added to the devicetree with an alias name
like in the following example:
chip soc/whateverlake
device gpio 0 alias soc_gpio on end
...
end
Any driver that requires access to this gpio device needs to have a
device pointer (or multiple) and an option for specifying the gpio to be
used in its chip config like this:
struct drivers_ipmi_config {
...
DEVTREE_CONST struct device *gpio_dev;
u16 post_complete_gpio;
...
};
The device `soc_gpio` can then be linked to the chip driver's `gpio_dev`
above by using the syntax `use ... as ...`, which was introduced in
commit 8e1ea52:
chip drivers/ipmi
use soc_gpio as gpio_dev
register "bmc_jumper_gpio" = "GPP_D22"
...
end
The IPMI driver can then use the generic gpio operations without any
knowlege of the chip's specifics:
unsigned int gpio_val;
const struct gpio_operations *gpio_ops;
gpio_ops = dev_get_gpio_ops(conf->gpio_dev);
gpio_val = gpio_ops->get(conf->bmc_jumper_gpio);
For a full example have a look at CB:48096 and CB:48095.
This change adds the new device type to sconfig and adds generic gpio
operations to the `device_operations` struct. Also, a helper for getting
the gpio operations from a device after checking them for NULL pointers
gets added.
Successfully tested on Supermicro X11SSM-F with CB:48097, X11SSH-TF with
CB:48711 and OCP DeltaLake with CB:48672.
Change-Id: Ic4572ad8b37bd1afd2fb213b2c67fb8aec536786
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The register `ESR` conflicts with the `Exception syndrome register` in
UDK2017. To resolve the conflict, drop the unused `ESR` register from
gma registers. It can be readded and prefixed or renamed if it's
required at a later point.
Change-Id: Icfdd834aea59ae69639a180221f5e97170fbac15
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: I002ade555c0544e4ef738c1ad45ee3d8aa38e03e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
We missed that Cannon Point, the PCH usually paired with Coffee, Whiskey
and Comet Lake, differs a bit from its predecessors. Hence, libgfxinit
now has a new Kconfig setting for the PCH.
Change-Id: I1c02c0d9abb7340aabe94185ee5e17ef4c2b0d36
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
All known on-chip PCI devices are documented in chipset devicetree now
and default to disabled. There is no need to keep disabled PCI devices
in the mainboard's devicetree. Thus, remove them.
Change-Id: I0f78dadd9e55a8f002394dc07ab514ca13f4e963
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ide10889ad01ec6d31ee83158182876625a68a5da
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48888
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a Kconfig option to set the tianocore boot timeout,
which is passed to the payload via a command line parameter.
Allows boards without an internal display (eg) to set a longer
boot timeout, in order to ensure the boot splash/menu prompt
are visible upon boot.
The associated changes on the tianocore side have already been
merged into MrChromebox's CorebootPayloadPkg and UefiPayloadPkg
branches (coreboot_fb and uefipayloadpkg respectively).
Change-Id: Ifeaadff05f6667d642c05b81f53c1d2dbc450af6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The CedarIsland FSP Integration recommends locking down some things.
Change-Id: I72e04b55d69a8da79485e084b39c3bd38504897f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47168
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is required for CbNT.
Change-Id: I565a95cd2e76cb1c648884be6d1954288f6e4804
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This is required for CBnT.
Change-Id: If5637eb8dd7de406b24b92100b68c5fa11c16854
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add rtc MT6359P driver for rtc init and rtc eosc calibration. Refactor
mt8173 and mt8183 code by extracting common API. Move rtc_read and
rtc_write to each SoC folder, because mt8173 and mt8183 access rtc via
pmic wrapper, while mt8192 accesses it via pmif.
Reference datasheet:
Document No: RH-D-2018-0101.
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.corp-partner.google.com>
Change-Id: I57d6738fdec148c7458b2024a0a8225415ca2f3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add basic devapc (device access permission control) drivers.
DAPC driver is used to set up bus fabric security and data protection
among hardwares. DAPC driver groups the master hardwares into different
domains and gives secure and non-secure property. The slave hardware can
configure different access permissions for different domains via DAPC
driver.
Change-Id: I2ad47c86b88047c76854a6f8a67b251b6a9d4013
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Before calibration, dramc resets the delay of each PHY IO, calculates
TX path and sets CKE to be rank independent.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I071eca037f89a916d6cfaf5b008d64f2b4a269a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
src/northbridge/amd/pi/00660F01/Kconfig does not exist. Remove the
source statement.
Also, no kconfig files under src/soc/intel/common/basecode/. Clean
that up.
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Change-Id: I10917b76ff6c2a9d5a97d5c7dfa9e8925cd8c8a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Now that CHAP device is declared in chipset devicetree, hook it up to
devicetree configuration.
Change-Id: Icc51f7b9cda32d5058dce958e386921b6d3d8ffb
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48323
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The code in soc/amd/common has an implementation of
GPIO register space that is compatible with the hardware
sb/amd/pi/hudson supports.
Change-Id: I86ae40a3cdf335263d7e9e3dcfdd588947cdd9b1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add SMBIOS slot descriptions for M.2 ports and remove duplicate
comments.
Change-Id: Ieff03ad3167aec054cdc6b67ddc20fc64394e347
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I1c1b5710a5236fe4a3bdda1fc978393e636e9817
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45773
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: If77d59485451c77dcea752bc4fe0dfadba8fec45
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48900
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Sandy Bridge steppings appear in the BWG, and Ivy Bridge steppings
appear in reference code. Add them for the sake of completeness.
Change-Id: I7d17cdd04a771ca319c908fc757f868e95ea7944
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The steppings correspond to the CPUID bits 3:0, so move them to the CPU
scope, and include the CPU header from files using the stepping macros.
Change-Id: Idf8fba4911f98953bb909777aea57295774d8400
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48409
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rewrite some constants to make their meaning somewhat clearer.
Tested with BUILD_TIMELESS=1, Asus P8Z77-V LX2 does not change.
Change-Id: I321f5e61d7c695ae77e61b84728e34930f69d400
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Native raminit only supports 1.5V operation, but there are DIMMs which
request 1.65V operation in XMP profiles. Add an option to force XMP to
be used when the requested voltage isn't supported, which will run the
DIMMs at 1.5V with XMP timings. Consider this to be overclocking.
Change-Id: I64bfac8f72dadf662ceadfc7998daf26edf5a710
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
We need this to happen prior to SMM module loader. If
there is some debugging output it's better they do not
appear in the middle of CPU bringup.
Change-Id: I45b4b5c0c5bf8bee258a465d1e364bfe98190e44
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I0d1e7b86d5b98da85bf539a4a3ec23e0eeaa4dfc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Structure with chromeos_acpi_t is expected to have size
0x1000. Only ones with device_nvs_t have size 0x2000.
Change-Id: I2eaa3a008566853b4144fa34ccffaa232d5d8e24
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Update galtic device tree override to match schematics.
BUG=b:170913840
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I270cd2a9783030ad3a080b9cfda8a133e801c5ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Rename to graphics_soc_panel_init, to more accurately convey
operations performed by the function. Guard execution so we
don't attempt to reconfigure the panel after FSP has already
done so.
This fixes FSP/GOP display init on APL/GLK, which was broken by
attempting to configure the panel after FSP had already done so.
Change-Id: I8e68a16b2efb59965077735578b1cc6ffd5a58f0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48884
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new driver for OEM commands and select it from x11-lga1151-series.
The driver communicates the BIOS version and date to the BMC using OEM
commands. The command should be supported on all X11 series mainboards,
but might work with older BMC, too.
Tested on X11SSH-TF:
The BIOS version strings are updated on boot and are visible in the
BMC web UI.
Change-Id: I51c22f83383affb70abb0efbcdc33ea925b5ff9f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: If1a9808d1f20ee61048182d416f25e9a81c631af
Signed-off-by: Sam Lewis <sam.vr.lewis@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I60699e044b5bacd3f5292fed7edbf529ae133284
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47592
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I643a821d4c41fc068f2bab0bd571b0a4a359f59a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I855d975a4729da34a6fa73a63dbbd12c856bdc00
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The keyboard self-test is required for some devices. At least one
device (integrated keyboard in a ThinkPad X201) actually starts the
test automatically leading to spurious output and no response for
the first seconds.
We wait up to 5s for the self-test result. On failure or timeout,
the command will be repeated until the 30s init timer runs out. This
happens all in the background of the UI polling loop.
To not unnecessarily delay the boot process, we first try an oppor-
tunistic initialization which skips the self-test.
Change-Id: Ie07b31e74d06e116ac81e76309621eed39a19b49
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Will be used to time out in states that don't always advance.
Change-Id: I28235e7638d8157cedf81fd915a41d28a1fc070b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47087
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We'll process the init sequence as part of the polling loop. This
should have several advantages:
* It eases error handling, i.e. we can return to an earlier state.
* We don't have to stall initialization when a keyboard takes a
little longer.
* Generally, these keyboards can be hot-plugged (albeit not by
design).
Change-Id: I9cf5cf31eb420b3994bec20e56a72d37f3d2996e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Draining the keyboard's buffer is only possible when the keyboard
port is enabled. We should also disable input scanning before, as
the buffer could be filled again with new keystrokes otherwise.
Change-Id: Ibac9c0d04880ff4a3efda5ac53da2f9731f6602c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Move the input-buffer draining into a function. It uses the low-level
i8042 API directly to avoid conflicts with changes in the high-level
keyboard API.
Change-Id: I9427c5b8be4d59c2ee3da12d6168d34590043682
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47084
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Even if we are careful, it's still possible that we read spurious
data from the keyboard, e.g. keystrokes. Namely, when we send the
reset/disable command, there is a race before the command is pro-
cessed.
So we should always process data from the keyboard in a loop. We
break it, when an ACK (0xfa) or a NAK (0xfe) is received, and warn
on unexpected data unless it might be due to the mentioned race.
This also gives us the opportunity to use command-specific timeouts
which we take from Linux: 1s for the keyboard self-test (as there
are keyboards that perform the test before acking the command) and
200ms for all other commands.
Change-Id: I60a2643a8ff4b9231c63bf970c8749c97c7d8926
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Only one EEPROM is used to store the board settings, and its I2C address
is constant. Thus, there's no need to pass its address as a parameter.
In addition, reduce the scope of the `I2C_ADDR_EEPROM` definition, since
using it outside of eeprom.c would bypass the API's abstraction layer.
Change-Id: I958304e6ed6df05af923139d44ff4fd1de204738
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Drop chipset register definitions in mainboard code in favor of existing
definitions in a header. These definitions are not mainboard-specific.
Tested with BUILD_TIMELESS=1, Prodrive Hermes remains identical.
Change-Id: I29d6f35ec27bff43cf52ae697e905b6a7b48a8d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: I0251d1193bb36ae73d592a0d17f580b7edaddbf6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48853
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch add SSD D3 cold support for lindar.
BUG=b:172405687
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: Ie343bbff3bde4ff2a7e89bd384d5661af372b560
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Based on latest schematic, disable PCIe 7 and 8 for WLAN and SD card.
BUG=b:169356808
TEST=FW_NAME=voema emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I2a4658a382c094c2a5b16b7acaf464f54e9897b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Newest master introduces the FSP for Tiger Lake client SKUs.
Change-Id: Id437faf72f1b8c5bc5310596bdab980e64614fa0
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48712
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Runtime D3 for the volteer variants that have GPIO power control
of the NVMe device attached to PCIe Root Port 9.
Enable the GPIO for power control for variants that do not already have
it configured to allow the power to be disabled in D3 state.
BUG=b:169356808
TEST=tested on voema
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I28ef074225c533e1a97b6ec4a1a5dd1dcc198168
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48848
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Isochronous operation negatively impacts memory performance, as
per Intel MLC (Memory Latency Checker) benchmark results. Thus,
disable isochronous operation, like analogous UEFI firmware does.
The MLC results after disabling isoch:
"--max_bandwidth"
ALL Reads : 106948.17
3:1 Reads-Writes : 101580.46
2:1 Reads-Writes : 100523.26
1:1 Reads-Writes : 99059.44
Stream-triad like : 97762.47
"--peak_injection_bandwidth"
ALL Reads : 105724.3
3:1 Reads-Writes : 100655.8
2:1 Reads-Writes : 99463
1:1 Reads-Writes : 98708
Stream-triad like : 91515
The MLC results before disabling isoch:
"--max_bandwidth"
ALL Reads : 88824.96
3:1 Reads-Writes : 94820.81
2:1 Reads-Writes : 94867.53
1:1 Reads-Writes : 92567.36
Stream-triad like : 91900.43
"--peak_injection_bandwidth"
ALL Reads : 88859.6
3:1 Reads-Writes : 94064
2:1 Reads-Writes : 94186.2
1:1 Reads-Writes : 92516.1
Stream-triad like : 85147.4
TEST=On OCP Delta Lake, verify that MLC benchmark results have
improved.
Change-Id: I08c22ee001b601e607452b3f23fad969ecb484b4
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48738
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A new board introduced to Kukui family.
BUG=b:176206134
TEST=make # select Katsu
BRANCH=kukui
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I09fe2b8f6922dfd2af6424830568466fb98f7aee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Remove the unused SOC_INTEL_COMMON_ACPI Kconfig option.
Change-Id: Id62cd44e0f7e4175ae65c9388569231d5c8c1fbc
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Remove the unnecessary header file includes.
Change-Id: I0d849cb236f304b87332aa64b2f10c73cad2d4dd
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
Leverage existing `ch_dimms` value and use constants for brevity.
Change-Id: I4e08166c8e9fbd15ff1dcd266abb0689e4b159f7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Pointers to structs can be very useful, especially when they point to an
array element. In this case, changing one pointer allows the function to
be rewritten more concisely, since most redundancy can be eliminated.
Tested on Asus P8Z77-V LX2, still boots. No functional difference.
Change-Id: I7f0c37ea49db640f197162f371165a6f8e9c1b9c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Ensure that IOSAV is finished before continuing. This might solve some
random failures on the I/O and roundtrip latency training algorithm.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: Ic08a40346b6c60e372bada10f9c4ee42eb974f9f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48403
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Most ofte, `iosav_run_once` precedes a `wait_for_iosav` call. Add a
helper function to reduce clutter. The cases where `iosav_run_once`
isn't followed by `wait_for_iosav` will be handled in a follow-up.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: Ic76f53c2db41512287f41b696a0c4df42a5e0f12
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48402
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These comments were helpful before the massive IOSAV refactoring, but
they are no longer needed since the function names are clear enough.
Change-Id: Ieb9bdf3f7fc72f63a8978f2b98e0bc8228c55868
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48401
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Print delay values in a suitable format for human consumption.
Change-Id: I0d86187d3e458ee2cb3fd11ec896ac363b8d3249
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48400
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I164daa59696f2fe8de3a4b3e7da46c7c723778eb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48602
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the purpose of each training algorithm is clear, replace the
last instances of the original names in comments and print statements
with the current, correct names. Also, print which channel has failed
command training, for completeness and consistency with other errors.
Change-Id: I9cc5c4b04499297825ca004c6bd1648a68449d2c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48601
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Document the algorithm to adjust I/O and roundtrip latencies.
Change-Id: Ic8b9aed54a34bb3252c457e87e81387fd410e305
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48397
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested on Asus P8H61-M PRO, still boots.
Change-Id: I147ba0ade8a5317a0fe76e9ea84947fd91d794b4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47773
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor in preparation to split up `program_timings`.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: I68410165f397d8b4f662e40e88fb6a58ab1c5cff
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47772
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use absolute values for the Rx and Tx bus timings instead of values
relative to the CA (Command/Address) bus timing. This makes the
calculations more accurate, less complex and less error-prone.
Tested on Asus P8H61-M PRO, still boots. Training results do not seem to
be affected by this patch, and the margins roughly have the same shape.
Change-Id: I28ff1bdaadf1fcbca6a5e5ccdd456de683206410
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47771
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This file was being written to the root src directory. It is the only
file being written to src during a normal build, while all others are
being written to $(obj). I added a new variable to allow specifying the
xcompile path. This allows generating a single file if building multiple
boards. I also moved the default location into $(obj) so we don't
pollute the src directory by default.
I also cleaned up the generation of xcompile by removing the unnecessary
eval and NOCOMPILE check.
I also left .xcompile in distclean so it cleans up stale files.
Since .xcompile is written into $(obj), `make clean` will now remove it.
The tegra Makefiles are outside of the normal build process, so I just
updated those Makefiles to point to the default xcompile location of a
normal build. The what-jenkins-does target had to be updated to support
these special targets. We generate an xcompile specifically for these
targets and pass it into the Makefile. Ideally we should get these
targets added to the main build.
BUG=b:112267918
TEST=ran `emerge-grunt coreboot` and `make what-jenkins-does`
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia83f234447b977efa824751c9674154b77d606b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
List of changes:
FSP-S Header:
- Add UPD MicrocodeRegionBase and MicrocodeRegionSize
- Adjust UPD Offset for Reservedxx
Change-Id: I376abf6cd64dcf8c848901074e2c2f30d4f302da
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
