diff options
Diffstat (limited to 'src/southbridge/intel/ich5r/i82801er_lpc.c')
| -rw-r--r-- | src/southbridge/intel/ich5r/i82801er_lpc.c | 392 |
1 files changed, 0 insertions, 392 deletions
diff --git a/src/southbridge/intel/ich5r/i82801er_lpc.c b/src/southbridge/intel/ich5r/i82801er_lpc.c deleted file mode 100644 index 3f77b51409..0000000000 --- a/src/southbridge/intel/ich5r/i82801er_lpc.c +++ /dev/null @@ -1,392 +0,0 @@ -/* - * (C) 2004 Linux Networx - */ -#include <console/console.h> -#include <device/device.h> -#include <device/pci.h> -#include <device/pci_ids.h> -#include <device/pci_ops.h> -#include <pc80/mc146818rtc.h> -#include <pc80/isa-dma.h> -#include <arch/io.h> -#include "i82801er.h" - -#define ACPI_BAR 0x40 -#define GPIO_BAR 0x58 - -#define NMI_OFF 0 -#define MAINBOARD_POWER_OFF 0 -#define MAINBOARD_POWER_ON 1 - -#ifndef MAINBOARD_POWER_ON_AFTER_POWER_FAIL -#define MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON -#endif - -#define ALL (0xff << 24) -#define NONE (0) -#define DISABLED (1 << 16) -#define ENABLED (0 << 16) -#define TRIGGER_EDGE (0 << 15) -#define TRIGGER_LEVEL (1 << 15) -#define POLARITY_HIGH (0 << 13) -#define POLARITY_LOW (1 << 13) -#define PHYSICAL_DEST (0 << 11) -#define LOGICAL_DEST (1 << 11) -#define ExtINT (7 << 8) -#define NMI (4 << 8) -#define SMI (2 << 8) -#define INT (1 << 8) - -static void setup_ioapic(void) -{ - int i; - unsigned long value_low, value_high; - unsigned long ioapic_base = 0xfec00000; - volatile unsigned long *l; - unsigned interrupts; - - l = (unsigned long *) ioapic_base; - - l[0] = 0x01; - interrupts = (l[04] >> 16) & 0xff; - for (i = 0; i < interrupts; i++) { - l[0] = (i * 2) + 0x10; - l[4] = DISABLED; - value_low = l[4]; - l[0] = (i * 2) + 0x11; - l[4] = NONE; /* Should this be an address? */ - value_high = l[4]; - if (value_low == 0xffffffff) { - printk_warning("IO APIC not responding.\n"); - return; - } - } - - /* Put the ioapic in virtual wire mode */ - l[0] = 0 + 0x10; - l[4] = ENABLED | TRIGGER_EDGE | POLARITY_HIGH | PHYSICAL_DEST | ExtINT; -} - -#define SERIRQ_CNTL 0x64 -static void i82801er_enable_serial_irqs(device_t dev) -{ - /* set packet length and toggle silent mode bit */ - pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(1 << 6)|((21 - 17) << 2)|(0 << 0)); - pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(0 << 6)|((21 - 17) << 2)|(0 << 0)); -} - -#define PCI_DMA_CFG 0x90 -static void i82801er_pci_dma_cfg(device_t dev) -{ - /* Set PCI DMA CFG to lpc I/F DMA */ - pci_write_config16(dev, PCI_DMA_CFG, 0xfcff); -} - -#define LPC_EN 0xe6 -static void i82801er_enable_lpc(device_t dev) -{ - /* lpc i/f enable */ - pci_write_config8(dev, LPC_EN, 0x0d); -} - -typedef struct southbridge_intel_i82801er_config config_t; - -static void set_i82801er_gpio_use_sel( - device_t dev, struct resource *res, config_t *config) -{ - uint32_t gpio_use_sel, gpio_use_sel2; - int i; - - gpio_use_sel = 0x1A003180; - gpio_use_sel2 = 0x00000007; - for(i = 0; i < 64; i++) { - int val; - switch(config->gpio[i] & ICH5R_GPIO_USE_MASK) { - case ICH5R_GPIO_USE_AS_NATIVE: val = 0; break; - case ICH5R_GPIO_USE_AS_GPIO: val = 1; break; - default: - continue; - } - /* The caller is responsible for not playing with unimplemented bits */ - if (i < 32) { - gpio_use_sel &= ~( 1 << i); - gpio_use_sel |= (val << i); - } else { - gpio_use_sel2 &= ~( 1 << (i - 32)); - gpio_use_sel2 |= (val << (i - 32)); - } - } - outl(gpio_use_sel, res->base + 0x00); - outl(gpio_use_sel2, res->base + 0x30); -} - -static void set_i82801er_gpio_direction( - device_t dev, struct resource *res, config_t *config) -{ - uint32_t gpio_io_sel, gpio_io_sel2; - int i; - - gpio_io_sel = 0x0000ffff; - gpio_io_sel2 = 0x00000300; - for(i = 0; i < 64; i++) { - int val; - switch(config->gpio[i] & ICH5R_GPIO_SEL_MASK) { - case ICH5R_GPIO_SEL_OUTPUT: val = 0; break; - case ICH5R_GPIO_SEL_INPUT: val = 1; break; - default: - continue; - } - /* The caller is responsible for not playing with unimplemented bits */ - if (i < 32) { - gpio_io_sel &= ~( 1 << i); - gpio_io_sel |= (val << i); - } else { - gpio_io_sel2 &= ~( 1 << (i - 32)); - gpio_io_sel2 |= (val << (i - 32)); - } - } - outl(gpio_io_sel, res->base + 0x04); - outl(gpio_io_sel2, res->base + 0x34); -} - -static void set_i82801er_gpio_level( - device_t dev, struct resource *res, config_t *config) -{ - uint32_t gpio_lvl, gpio_lvl2; - uint32_t gpio_blink; - int i; - - gpio_lvl = 0x1b3f0000; - gpio_blink = 0x00040000; - gpio_lvl2 = 0x00030207; - for(i = 0; i < 64; i++) { - int val, blink; - switch(config->gpio[i] & ICH5R_GPIO_LVL_MASK) { - case ICH5R_GPIO_LVL_LOW: val = 0; blink = 0; break; - case ICH5R_GPIO_LVL_HIGH: val = 1; blink = 0; break; - case ICH5R_GPIO_LVL_BLINK: val = 1; blink = 1; break; - default: - continue; - } - /* The caller is responsible for not playing with unimplemented bits */ - if (i < 32) { - gpio_lvl &= ~( 1 << i); - gpio_blink &= ~( 1 << i); - gpio_lvl |= ( val << i); - gpio_blink |= (blink << i); - } else { - gpio_lvl2 &= ~( 1 << (i - 32)); - gpio_lvl2 |= (val << (i - 32)); - } - } - outl(gpio_lvl, res->base + 0x0c); - outl(gpio_blink, res->base + 0x18); - outl(gpio_lvl2, res->base + 0x38); -} - -static void set_i82801er_gpio_inv( - device_t dev, struct resource *res, config_t *config) -{ - uint32_t gpio_inv; - int i; - - gpio_inv = 0x00000000; - for(i = 0; i < 32; i++) { - int val; - switch(config->gpio[i] & ICH5R_GPIO_INV_MASK) { - case ICH5R_GPIO_INV_OFF: val = 0; break; - case ICH5R_GPIO_INV_ON: val = 1; break; - default: - continue; - } - gpio_inv &= ~( 1 << i); - gpio_inv |= (val << i); - } - outl(gpio_inv, res->base + 0x2c); -} - -static void i82801er_pirq_init(device_t dev) -{ - config_t *config; - - /* Get the chip configuration */ - config = dev->chip_info; - - if(config->pirq_a_d) { - pci_write_config32(dev, 0x60, config->pirq_a_d); - } - if(config->pirq_e_h) { - pci_write_config32(dev, 0x68, config->pirq_e_h); - } -} - - -static void i82801er_gpio_init(device_t dev) -{ - struct resource *res; - config_t *config; - - /* Skip if I don't have any configuration */ - if (!dev->chip_info) { - return; - } - /* The programmer is responsible for ensuring - * a valid gpio configuration. - */ - - /* Get the chip configuration */ - config = dev->chip_info; - /* Find the GPIO bar */ - res = find_resource(dev, GPIO_BAR); - if (!res) { - return; - } - - /* Set the use selects */ - set_i82801er_gpio_use_sel(dev, res, config); - - /* Set the IO direction */ - set_i82801er_gpio_direction(dev, res, config); - - /* Setup the input inverters */ - set_i82801er_gpio_inv(dev, res, config); - - /* Set the value on the GPIO output pins */ - set_i82801er_gpio_level(dev, res, config); - -} - -static void enable_hpet(struct device *dev) -{ -const unsigned long hpet_address = 0xfed0000; - - uint32_t dword; - uint32_t code = (0 & 0x3); - - dword = pci_read_config32(dev, GEN_CNTL); - dword |= (1 << 17); /* enable hpet */ - - /* Bits [16:15] Memory Address Range - * 00 FED0_0000h - FED0_03FFh - * 01 FED0_1000h - FED0_13FFh - * 10 FED0_2000h - FED0_23FFh - * 11 FED0_3000h - FED0_33FFh - */ - - dword &= ~(3 << 15); /* clear it */ - dword |= (code<<15); - - printk_debug("enabling HPET @0x%x\n", hpet_address | (code <<12) ); -} - -static void lpc_init(struct device *dev) -{ - uint8_t byte; - uint32_t value; - int pwr_on=MAINBOARD_POWER_ON_AFTER_POWER_FAIL; - - /* IO APIC initialization */ - value = pci_read_config32(dev, 0xd0); - value |= (1 << 8)|(1<<7)|(1<<1); - pci_write_config32(dev, 0xd0, value); - value = pci_read_config32(dev, 0xd4); - value |= (1<<1); - pci_write_config32(dev, 0xd4, value); - setup_ioapic(); - - i82801er_enable_serial_irqs(dev); - - i82801er_pci_dma_cfg(dev); - - i82801er_enable_lpc(dev); - - /* Clear SATA to non raid */ - pci_write_config8(dev, 0xae, 0x00); - - get_option(&pwr_on, "power_on_after_fail"); - byte = pci_read_config8(dev, 0xa4); - byte &= 0xfe; - if (!pwr_on) { - byte |= 1; - } - pci_write_config8(dev, 0xa4, byte); - printk_info("set power %s after power fail\n", pwr_on?"on":"off"); - - /* Set up the PIRQ */ - i82801er_pirq_init(dev); - - /* Set the state of the gpio lines */ - i82801er_gpio_init(dev); - - /* Initialize the real time clock */ - rtc_init(0); - - /* Initialize isa dma */ - isa_dma_init(); - - /* Disable IDE (needed when sata is enabled) */ - pci_write_config8(dev, 0xf2, 0x60); - - enable_hpet(dev); -} - -static void i82801er_lpc_read_resources(device_t dev) -{ - struct resource *res; - - /* Get the normal pci resources of this device */ - pci_dev_read_resources(dev); - - /* Add the ACPI BAR */ - res = pci_get_resource(dev, ACPI_BAR); - - /* Add the GPIO BAR */ - res = pci_get_resource(dev, GPIO_BAR); - - /* Add an extra subtractive resource for both memory and I/O */ - res = new_resource(dev, IOINDEX_SUBTRACTIVE(0, 0)); - res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED; - - res = new_resource(dev, IOINDEX_SUBTRACTIVE(1, 0)); - res->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED; -} - -static void i82801er_lpc_enable_resources(device_t dev) -{ - uint8_t acpi_cntl, gpio_cntl; - - /* Enable the normal pci resources */ - pci_dev_enable_resources(dev); - - /* Enable the ACPI bar */ - acpi_cntl = pci_read_config8(dev, 0x44); - acpi_cntl |= (1 << 4); - pci_write_config8(dev, 0x44, acpi_cntl); - - /* Enable the GPIO bar */ - gpio_cntl = pci_read_config8(dev, 0x5c); - gpio_cntl |= (1 << 4); - pci_write_config8(dev, 0x5c, gpio_cntl); - - enable_childrens_resources(dev); -} - -static struct pci_operations lops_pci = { - .set_subsystem = 0, -}; - -static struct device_operations lpc_ops = { - .read_resources = i82801er_lpc_read_resources, - .set_resources = pci_dev_set_resources, - .enable_resources = i82801er_lpc_enable_resources, - .init = lpc_init, - .scan_bus = scan_static_bus, - .enable = i82801er_enable, - .ops_pci = &lops_pci, -}; - -static struct pci_driver lpc_driver __pci_driver = { - .ops = &lpc_ops, - .vendor = PCI_VENDOR_ID_INTEL, - .device = PCI_DEVICE_ID_INTEL_82801ER_ISA, -}; |