1 files changed, 230 insertions, 0 deletions
diff --git a/src/soc/amd/morgana/fch.c b/src/soc/amd/morgana/fch.c
new file mode 100644
index 0000000000..f9f4649438
--- /dev/null
+++ b/src/soc/amd/morgana/fch.c
@@ -0,0 +1,230 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+/* TODO: Update for Morgana */
+
+#include <amdblocks/acpi.h>
+#include <amdblocks/acpimmio.h>
+#include <amdblocks/amd_pci_util.h>
+#include <amdblocks/gpio.h>
+#include <amdblocks/smi.h>
+#include <assert.h>
+#include <bootstate.h>
+#include <cpu/x86/smm.h>
+#include <amdblocks/i2c.h>
+#include <soc/amd_pci_int_defs.h>
+#include <soc/iomap.h>
+#include <soc/i2c.h>
+#include <soc/smi.h>
+#include <soc/southbridge.h>
+#include "chip.h"
+
+/*
+ * Table of APIC register index and associated IRQ name. Using IDX_XXX_NAME
+ * provides a visible association with the index, therefore helping
+ * maintainability of table. If a new index/name is defined in
+ * amd_pci_int_defs.h, just add the pair at the end of this table.
+ * Order is not important.
+ */
+const static struct irq_idx_name irq_association[] = {
+	{ PIRQ_A,	"INTA#" },
+	{ PIRQ_B,	"INTB#" },
+	{ PIRQ_C,	"INTC#" },
+	{ PIRQ_D,	"INTD#" },
+	{ PIRQ_E,	"INTE#" },
+	{ PIRQ_F,	"INTF#/GENINT2" },
+	{ PIRQ_G,	"INTG#" },
+	{ PIRQ_H,	"INTH#" },
+	{ PIRQ_MISC,	"Misc" },
+	{ PIRQ_MISC0,	"Misc0" },
+	{ PIRQ_HPET_L,	"HPET_L" },
+	{ PIRQ_HPET_H,	"HPET_H" },
+	{ PIRQ_SIRQA,	"Ser IRQ INTA" },
+	{ PIRQ_SIRQB,	"Ser IRQ INTB" },
+	{ PIRQ_SIRQC,	"Ser IRQ INTC" },
+	{ PIRQ_SIRQD,	"Ser IRQ INTD" },
+	{ PIRQ_SCI,	"SCI" },
+	{ PIRQ_SMBUS,	"SMBUS" },
+	{ PIRQ_ASF,	"ASF" },
+	{ PIRQ_PMON,	"PerMon" },
+	{ PIRQ_SD,	"SD" },
+	{ PIRQ_SDIO,	"SDIO" },
+	{ PIRQ_CIR,	"CIR" },
+	{ PIRQ_GPIOA,	"GPIOa" },
+	{ PIRQ_GPIOB,	"GPIOb" },
+	{ PIRQ_GPIOC,	"GPIOc" },
+	{ PIRQ_EMMC,	"eMMC" },
+	{ PIRQ_GPP0,	"GPP0" },
+	{ PIRQ_GPP1,	"GPP1" },
+	{ PIRQ_GPP2,	"GPP2" },
+	{ PIRQ_GPP3,	"GPP3" },
+	{ PIRQ_GPIO,	"GPIO" },
+	{ PIRQ_I2C0,	"I2C0" },
+	{ PIRQ_I2C1,	"I2C1" },
+	{ PIRQ_I2C2,	"I2C2" },
+	{ PIRQ_I2C3,	"I2C3" },
+	{ PIRQ_UART0,	"UART0" },
+	{ PIRQ_UART1,	"UART1" },
+	{ PIRQ_I2C4,	"I2C4" },
+	{ PIRQ_UART4,	"UART4" },
+	{ PIRQ_UART2,	"UART2" },
+	{ PIRQ_UART3,	"UART3" },
+};
+
+const struct irq_idx_name *sb_get_apic_reg_association(size_t *size)
+{
+	*size = ARRAY_SIZE(irq_association);
+	return irq_association;
+}
+
+static void fch_clk_output_48Mhz(void)
+{
+	uint32_t ctrl = misc_read32(MISC_CLK_CNTL0);
+	/* Enable BP_X48M0 Clock Output */
+	ctrl |= BP_X48M0_OUTPUT_EN;
+	/* Disable clock output in S0i3 */
+	ctrl |= BP_X48M0_S0I3_DIS;
+	misc_write32(MISC_CLK_CNTL0, ctrl);
+}
+
+static void fch_init_acpi_ports(void)
+{
+	u32 reg;
+
+	/* We use some of these ports in SMM regardless of whether or not
+	 * ACPI tables are generated. Enable these ports indiscriminately.
+	 */
+
+	pm_write16(PM_EVT_BLK, ACPI_PM_EVT_BLK);
+	pm_write16(PM1_CNT_BLK, ACPI_PM1_CNT_BLK);
+	pm_write16(PM_TMR_BLK, ACPI_PM_TMR_BLK);
+	pm_write16(PM_GPE0_BLK, ACPI_GPE0_BLK);
+
+	if (CONFIG(HAVE_SMI_HANDLER)) {
+		/* APMC - SMI Command Port */
+		pm_write16(PM_ACPI_SMI_CMD, APM_CNT);
+		configure_smi(SMITYPE_SMI_CMD_PORT, SMI_MODE_SMI);
+
+		/* SMI on SlpTyp requires sending SMI before completion
+		   response of the I/O write. */
+		reg = pm_read32(PM_PCI_CTRL);
+		reg |= FORCE_SLPSTATE_RETRY;
+		pm_write32(PM_PCI_CTRL, reg);
+
+		/* Disable SlpTyp feature */
+		reg = pm_read8(PM_RST_CTRL1);
+		reg &= ~SLPTYPE_CONTROL_EN;
+		pm_write8(PM_RST_CTRL1, reg);
+
+		configure_smi(SMITYPE_SLP_TYP, SMI_MODE_SMI);
+	} else {
+		pm_write16(PM_ACPI_SMI_CMD, 0);
+	}
+
+	/* Decode ACPI registers and enable standard features */
+	pm_write8(PM_ACPI_CONF, PM_ACPI_DECODE_STD |
+				PM_ACPI_GLOBAL_EN |
+				PM_ACPI_RTC_EN_EN |
+				PM_ACPI_TIMER_EN_EN);
+}
+
+/* configure the general purpose PCIe clock outputs according to the devicetree settings */
+static void gpp_clk_setup(void)
+{
+	const struct soc_amd_morgana_config *cfg = config_of_soc();
+
+	/* look-up table to be able to iterate over the PCIe clock output settings */
+	const uint8_t gpp_clk_shift_lut[GPP_CLK_OUTPUT_COUNT] = {
+		GPP_CLK0_REQ_SHIFT,
+		GPP_CLK1_REQ_SHIFT,
+		GPP_CLK2_REQ_SHIFT,
+		GPP_CLK3_REQ_SHIFT,
+		GPP_CLK4_REQ_SHIFT,
+		GPP_CLK5_REQ_SHIFT,
+		GPP_CLK6_REQ_SHIFT,
+	};
+
+	uint32_t gpp_clk_ctl = misc_read32(GPP_CLK_CNTRL);
+
+	for (int i = 0; i < GPP_CLK_OUTPUT_COUNT; i++) {
+		gpp_clk_ctl &= ~GPP_CLK_REQ_MASK(gpp_clk_shift_lut[i]);
+		/*
+		 * The remapping of values is done so that the default of the enum used for the
+		 * devicetree settings is the clock being enabled, so that a missing devicetree
+		 * configuration for this will result in an always active clock and not an
+		 * inactive PCIe clock output. Only the configuration for the clock outputs
+		 * available on the package is provided via the devicetree; the rest is
+		 * switched off unconditionally.
+		 */
+		switch (i < GPP_CLK_OUTPUT_AVAILABLE ? cfg->gpp_clk_config[i] : GPP_CLK_OFF) {
+		case GPP_CLK_REQ:
+			gpp_clk_ctl |= GPP_CLK_REQ_EXT(gpp_clk_shift_lut[i]);
+			break;
+		case GPP_CLK_OFF:
+			gpp_clk_ctl |= GPP_CLK_REQ_OFF(gpp_clk_shift_lut[i]);
+			break;
+		case GPP_CLK_ON:
+		default:
+			gpp_clk_ctl |= GPP_CLK_REQ_ON(gpp_clk_shift_lut[i]);
+		}
+	}
+
+	misc_write32(GPP_CLK_CNTRL, gpp_clk_ctl);
+}
+
+static void cgpll_clock_gate_init(void)
+{
+	uint32_t t;
+
+	t = misc_read32(MISC_CLKGATEDCNTL);
+	t |= ALINKCLK_GATEOFFEN;
+	t |= BLINKCLK_GATEOFFEN;
+	t |= XTAL_PAD_S0I3_TURNOFF_EN;
+	t |= XTAL_PAD_S3_TURNOFF_EN;
+	t |= XTAL_PAD_S5_TURNOFF_EN;
+	misc_write32(MISC_CLKGATEDCNTL, t);
+
+	t = misc_read32(MISC_CGPLL_CONFIGURATION0);
+	t |= USB_PHY_CMCLK_S3_DIS;
+	t |= USB_PHY_CMCLK_S0I3_DIS;
+	t |= USB_PHY_CMCLK_S5_DIS;
+	misc_write32(MISC_CGPLL_CONFIGURATION0, t);
+
+	t = pm_read32(PM_ISACONTROL);
+	t |= ABCLKGATEEN;
+	pm_write32(PM_ISACONTROL, t);
+}
+
+void fch_init(void *chip_info)
+{
+	i2c_soc_init();
+	fch_init_acpi_ports();
+
+	acpi_pm_gpe_add_events_print_events();
+	gpio_add_events();
+
+	gpp_clk_setup();
+	fch_clk_output_48Mhz();
+	cgpll_clock_gate_init();
+}
+
+void fch_final(void *chip_info)
+{
+}
+
+static void set_pci_irqs(void *unused)
+{
+	/* Write PCI_INTR regs 0xC00/0xC01 */
+	write_pci_int_table();
+
+	/* pirq_data is consumed by `write_pci_cfg_irqs` */
+	populate_pirq_data();
+
+	/* Write IRQs for all devicetree enabled devices */
+	write_pci_cfg_irqs();
+}
+
+/*
+ * Hook this function into the PCI state machine
+ * on entry into BS_DEV_ENABLE.
+ */
+BOOT_STATE_INIT_ENTRY(BS_DEV_ENABLE, BS_ON_ENTRY, set_pci_irqs, NULL);