summaryrefslogtreecommitdiff
path: root/src/mainboard/google/brya/variants
diff options
context:
space:
mode:
Diffstat (limited to 'src/mainboard/google/brya/variants')
-rw-r--r--src/mainboard/google/brya/variants/pujjo/overridetree.cb349
1 files changed, 347 insertions, 2 deletions
diff --git a/src/mainboard/google/brya/variants/pujjo/overridetree.cb b/src/mainboard/google/brya/variants/pujjo/overridetree.cb
index 4f2c04a57a..212970451d 100644
--- a/src/mainboard/google/brya/variants/pujjo/overridetree.cb
+++ b/src/mainboard/google/brya/variants/pujjo/overridetree.cb
@@ -1,6 +1,351 @@
chip soc/intel/alderlake
+ register "sagv" = "SaGv_Enabled"
- device domain 0 on
- end
+ # SOC Aux orientation override:
+ # This is a bitfield that corresponds to up to 4 TCSS ports.
+ # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2.
+ # TcssAuxOri = 0101b
+ # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports
+ # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the
+ # motherboard to USBC connector
+ register "tcss_aux_ori" = "5"
+ register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
+
+ register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN
+
+ # Configure external V1P05/Vnn/VnnSx Rails
+ register "ext_fivr_settings" = "{
+ .configure_ext_fivr = 1,
+ .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX,
+ .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX,
+ .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX,
+ .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL,
+ .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE,
+ .v1p05_voltage_mv = 1050,
+ .vnn_voltage_mv = 780,
+ .vnn_sx_voltage_mv = 1050,
+ .v1p05_icc_max_ma = 500,
+ .vnn_icc_max_ma = 500,
+ }"
+
+ # Intel Common SoC Config
+ #+-------------------+---------------------------+
+ #| Field | Value |
+ #+-------------------+---------------------------+
+ #| I2C0 | TPM. Early init is |
+ #| | required to set up a BAR |
+ #| | for TPM communication |
+ #| I2C1 | Touchscreen |
+ #| I2C2 | Sub-board(PSensor)/WCAM |
+ #| I2C3 | Audio |
+ #| I2C5 | Trackpad |
+ #+-------------------+---------------------------+
+ register "common_soc_config" = "{
+ .i2c[0] = {
+ .early_init = 1,
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 160,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[1] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 157,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[2] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 157,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[3] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 158,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[5] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 158,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ }"
+
+ device domain 0 on
+ device ref i2c1 on
+ chip drivers/i2c/hid
+ register "generic.hid" = ""ELAN9004""
+ register "generic.desc" = ""ELAN Touchscreen""
+ register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+ register "generic.probed" = "1"
+ register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+ register "generic.reset_delay_ms" = "20"
+ register "generic.reset_off_delay_ms" = "2"
+ register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+ register "generic.stop_delay_ms" = "280"
+ register "generic.stop_off_delay_ms" = "2"
+ register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+ register "generic.enable_delay_ms" = "1"
+ register "generic.has_power_resource" = "1"
+ register "generic.disable_gpio_export_in_crs" = "1"
+ register "hid_desc_reg_offset" = "0x01"
+ device i2c 10 on end
+ end
+ chip drivers/i2c/hid
+ register "generic.hid" = ""GTCH7503""
+ register "generic.desc" = ""G2TOUCH Touchscreen""
+ register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+ register "generic.probed" = "1"
+ register "generic.reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+ register "generic.reset_delay_ms" = "50"
+ register "generic.enable_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+ register "generic.enable_delay_ms" = "1"
+ register "generic.has_power_resource" = "1"
+ register "generic.disable_gpio_export_in_crs" = "1"
+ register "hid_desc_reg_offset" = "0x01"
+ device i2c 40 on end
+ end
+ chip drivers/generic/gpio_keys
+ register "name" = ""PENH""
+ register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F13)"
+ register "key.wake_gpe" = "GPE0_DW2_15"
+ register "key.wakeup_route" = "WAKEUP_ROUTE_SCI"
+ register "key.wakeup_event_action" = "EV_ACT_DEASSERTED"
+ register "key.dev_name" = ""EJCT""
+ register "key.linux_code" = "SW_PEN_INSERTED"
+ register "key.linux_input_type" = "EV_SW"
+ register "key.label" = ""pen_eject""
+ device generic 0 on end
+ end
+ end
+ device ref i2c2 on
+ chip drivers/i2c/sx9324
+ register "desc" = ""SAR Proximity Sensor""
+ register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)"
+ register "speed" = "I2C_SPEED_FAST"
+ register "uid" = "1"
+ register "reg_gnrl_ctrl0" = "0x16"
+ register "reg_gnrl_ctrl1" = "0x21"
+ register "reg_afe_ctrl0" = "0x00"
+ register "reg_afe_ctrl1" = "0x10"
+ register "reg_afe_ctrl2" = "0x00"
+ register "reg_afe_ctrl3" = "0x00"
+ register "reg_afe_ctrl4" = "0x07"
+ register "reg_afe_ctrl5" = "0x00"
+ register "reg_afe_ctrl6" = "0x00"
+ register "reg_afe_ctrl7" = "0x07"
+ register "reg_afe_ctrl8" = "0x12"
+ register "reg_afe_ctrl9" = "0x0f"
+ register "reg_prox_ctrl0" = "0x12"
+ register "reg_prox_ctrl1" = "0x12"
+ register "reg_prox_ctrl2" = "0x90"
+ register "reg_prox_ctrl3" = "0x60"
+ register "reg_prox_ctrl4" = "0x0c"
+ register "reg_prox_ctrl5" = "0x12"
+ register "reg_prox_ctrl6" = "0x3c"
+ register "reg_prox_ctrl7" = "0x58"
+ register "reg_adv_ctrl0" = "0x00"
+ register "reg_adv_ctrl1" = "0x00"
+ register "reg_adv_ctrl2" = "0x00"
+ register "reg_adv_ctrl3" = "0x00"
+ register "reg_adv_ctrl4" = "0x00"
+ register "reg_adv_ctrl5" = "0x05"
+ register "reg_adv_ctrl6" = "0x00"
+ register "reg_adv_ctrl7" = "0x00"
+ register "reg_adv_ctrl8" = "0x00"
+ register "reg_adv_ctrl9" = "0x00"
+ register "reg_adv_ctrl10" = "0x5c"
+ register "reg_adv_ctrl11" = "0x52"
+ register "reg_adv_ctrl12" = "0xb5"
+ register "reg_adv_ctrl13" = "0x00"
+ register "reg_adv_ctrl14" = "0x80"
+ register "reg_adv_ctrl15" = "0x0c"
+ register "reg_adv_ctrl16" = "0x38"
+ register "reg_adv_ctrl17" = "0x56"
+ register "reg_adv_ctrl18" = "0x33"
+ register "reg_adv_ctrl19" = "0xf0"
+ register "reg_adv_ctrl20" = "0xf0"
+ device i2c 28 on end
+ end
+ end
+ device ref i2c3 on
+ chip drivers/i2c/generic
+ register "hid" = ""RTL5682""
+ register "name" = ""RT58""
+ register "desc" = ""Headset Codec""
+ register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
+ # Set the jd_src to RT5668_JD1 for jack detection
+ register "property_count" = "1"
+ register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
+ register "property_list[0].name" = ""realtek,jd-src""
+ register "property_list[0].integer" = "1"
+ device i2c 1a on end
+ end
+ chip drivers/generic/alc1015
+ register "hid" = ""RTL1019""
+ register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
+ device generic 0 on end
+ end
+ end
+ device ref i2c5 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0000""
+ register "desc" = ""ELAN Touchpad""
+ register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
+ register "wake" = "GPE0_DW2_14"
+ register "probed" = "1"
+ device i2c 15 on end
+ end
+ chip drivers/i2c/hid
+ register "generic.hid" = ""PNP0C50""
+ register "generic.desc" = ""Synaptics Touchpad""
+ register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
+ register "generic.wake" = "GPE0_DW2_14"
+ register "generic.probed" = "1"
+ register "hid_desc_reg_offset" = "0x20"
+ device i2c 0x2c on end
+ end
+ end
+ device ref hda on
+ chip drivers/generic/max98357a
+ register "hid" = ""MX98360A""
+ register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
+ register "sdmode_delay" = "5"
+ device generic 0 on end
+ end
+ end
+ device ref pcie_rp7 on
+ # Enable SD Card PCIe 7 using clk 3
+ register "pch_pcie_rp[PCH_RP(7)]" = "{
+ .clk_src = 3,
+ .clk_req = 3,
+ .flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
+ }"
+ chip soc/intel/common/block/pcie/rtd3
+ register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
+ register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)"
+ register "srcclk_pin" = "3"
+ device generic 0 on end
+ end
+ end
+ device ref pch_espi on
+ chip ec/google/chromeec
+ use conn0 as mux_conn[0]
+ device pnp 0c09.0 on end
+ end
+ end
+ device ref pmc hidden
+ chip drivers/intel/pmc_mux
+ device generic 0 on
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port1 as usb2_port
+ use tcss_usb3_port1 as usb3_port
+ device generic 0 alias conn0 on end
+ end
+ end
+ end
+ end
+ device ref tcss_xhci on
+ chip drivers/usb/acpi
+ device ref tcss_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
+ device ref tcss_usb3_port1 on end
+ end
+ end
+ end
+ end
+ device ref xhci on
+ chip drivers/usb/acpi
+ device ref xhci_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
+ device ref usb2_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 WWAN""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port2 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
+ device ref usb2_port3 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A1 (DB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
+ device ref usb2_port4 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 UFC""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port6 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 WFC""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port7 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Bluetooth""
+ register "type" = "UPC_TYPE_INTERNAL"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
+ device ref usb2_port10 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
+ device ref usb3_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A1 (DB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
+ device ref usb3_port2 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 WWAN""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb3_port3 on end
+ end
+ end
+ end
+ end
+ end
end
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-06 05:15:22 +0000