diff options
Diffstat (limited to 'src/mainboard/google/brya/variants/teliks/overridetree.cb')
| -rw-r--r-- | src/mainboard/google/brya/variants/teliks/overridetree.cb | 542 |
1 files changed, 542 insertions, 0 deletions
diff --git a/src/mainboard/google/brya/variants/teliks/overridetree.cb b/src/mainboard/google/brya/variants/teliks/overridetree.cb new file mode 100644 index 0000000000..093a353b60 --- /dev/null +++ b/src/mainboard/google/brya/variants/teliks/overridetree.cb @@ -0,0 +1,542 @@ +fw_config + field WIFI 8 9 + option UNKNOWN 0 + option WIFI_6 1 + option WIFI_6E 2 + end + field CAMERA 10 11 + option UF_720P_WF 0 + option UF_1080P 1 + option UF_720P 2 + option UF_1080P_WF 3 + end +end + +chip soc/intel/alderlake + register "sagv" = "SaGv_Enabled" + + # EMMC Tx CMD Delay + # Refer to EDS-Vol2-42.3.7. + # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" + + # EMMC TX DATA Delay 1 + # Refer to EDS-Vol2-42.3.8. + # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. + # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" + + # EMMC TX DATA Delay 2 + # Refer to EDS-Vol2-42.3.9. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. + # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828" + + # EMMC RX CMD/DATA Delay 1 + # Refer to EDS-Vol2-42.3.10. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. + # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F1B" + + # EMMC RX CMD/DATA Delay 2 + # Refer to EDS-Vol2-42.3.12. + # [17:16] stands for Rx Clock before Output Buffer, + # 00: Rx clock after output buffer, + # 01: Rx clock before output buffer, + # 10: Automatic selection based on working mode. + # 11: Reserved + # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10051" + + # EMMC Rx Strobe Delay + # Refer to EDS-Vol2-42.3.11. + # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. + # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x01515" + + # FIVR configurations for teliks are disabled since the board doesn't have V1p05 and Vnn + # bypass rails implemented. + register "ext_fivr_settings" = "{ + .configure_ext_fivr = 0, + }" + + # Enable the Cnvi BT Audio Offload + register "cnvi_bt_audio_offload" = "1" + + # Intel Common SoC Config + #+-------------+------------------------------+ + #| Field | Value | + #+-------------+------------------------------+ + #| I2C0 | TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C1 | Touchscreen | + #| I2C2 | Sub-board(PSensor)/WCAM | + #| I2C3 | Audio | + #| I2C5 | Trackpad | + #+-------------+------------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .early_init = 1, + .speed = I2C_SPEED_FAST_PLUS, + .speed_config[0] = { + .speed = I2C_SPEED_FAST_PLUS, + .scl_lcnt = 55, + .scl_hcnt = 30, + .sda_hold = 7, + } + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 160, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[2] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 157, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[3] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 157, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 152, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + }" + + # Power limit config + register "power_limits_config[ADL_N_041_6W_CORE]" = "{ + .tdp_pl1_override = 15, + .tdp_pl2_override = 25, + .tdp_pl4 = 78, + }" + + device domain 0 on + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""CPU_VR"" + register "options.tsr[1].desc" = ""CPU"" + register "options.tsr[2].desc" = ""Ambient"" + register "options.tsr[3].desc" = ""Charger"" + + # TODO: below values are initial reference values only + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), + [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 75, 5000), + [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), + [4] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_3, 75, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(TEMP_SENSOR_1, 100, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_2, 80, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 6000, + .max_power = 15000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 200 + }, + .pl2 = { + .min_power = 25000, + .max_power = 25000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 1000 + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 3000 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + device generic 0 on end + end + end + device ref igpu on + chip drivers/gfx/generic + register "device_count" = "4" + # DDIA for eDP + register "device[0].name" = ""LCD0"" + # Internal panel on the first port of the graphics chip + register "device[0].type" = "panel" + # DDIB for HDMI + # If HDMI is not enumerated in the kernel, then no GFX device should be added for DDIB + register "device[1].name" = ""DD01"" + # TCP0 (DP-1) for port C0 + register "device[2].name" = ""DD02"" + register "device[2].use_pld" = "true" + register "device[2].pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))" + # TCP1 (DP-2) for port C1 + register "device[3].name" = ""DD03"" + register "device[3].use_pld" = "true" + register "device[3].pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" + device generic 0 on end + end + end + device ref ipu on + chip drivers/intel/mipi_camera + register "acpi_uid" = "0x50000" + register "acpi_name" = ""IPU0"" + register "device_type" = "INTEL_ACPI_CAMERA_CIO2" + + register "cio2_num_ports" = "1" + register "cio2_lanes_used" = "{4}" # 4 CSI Camera lanes are used + register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0"" + register "cio2_prt[0]" = "1" + device generic 0 on + probe CAMERA UF_720P_WF + probe CAMERA UF_1080P_WF + end + end + end + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""ILTK0001"" + register "generic.desc" = ""ILITEK Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "200" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "12" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_off_delay_ms" = "200" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 41 on end + end + chip drivers/generic/gpio_keys + register "name" = ""PENH"" + register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F13)" + register "key.wake_gpe" = "GPE0_DW2_15" + register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" + register "key.wakeup_event_action" = "EV_ACT_ANY" + register "key.dev_name" = ""EJCT"" + register "key.linux_code" = "SW_PEN_INSERTED" + register "key.linux_input_type" = "EV_SW" + register "key.label" = ""pen_eject"" + device generic 0 on end + end + end + device ref i2c2 on + chip drivers/intel/mipi_camera + register "acpi_hid" = ""OVTIDB10"" + register "acpi_uid" = "0" + register "acpi_name" = ""CAM0"" + register "chip_name" = ""Ov 13b10 Camera"" + register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" + + register "ssdb.lanes_used" = "4" + register "ssdb.vcm_type" = "0x0C" + register "vcm_name" = ""VCM0"" + register "num_freq_entries" = "1" + register "link_freq[0]" = "560 * MHz" + register "remote_name" = ""IPU0"" + + register "has_power_resource" = "1" + #Controls + register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" + register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" + + register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X + register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1200_WCAM_X + register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L + + #_ON + register "on_seq.ops_cnt" = "5" + register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" + register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" + register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" + register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" + register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" + + #_OFF + register "off_seq.ops_cnt" = "4" + register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" + register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" + register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" + register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + + device i2c 36 on + probe CAMERA UF_720P_WF + probe CAMERA UF_1080P_WF + end + end + chip drivers/intel/mipi_camera + register "acpi_uid" = "2" + register "acpi_name" = ""VCM0"" + register "chip_name" = ""DW9714 VCM "" + register "device_type" = "INTEL_ACPI_CAMERA_VCM" + + register "vcm_compat" = ""dongwoon,dw9714"" + + register "has_power_resource" = "1" + #Controls + register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_AFVDD + + #_ON + register "on_seq.ops_cnt" = "1" + register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" + + #_OFF + register "off_seq.ops_cnt" = "1" + register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + + device i2c 0C on + probe CAMERA UF_720P_WF + probe CAMERA UF_1080P_WF + end + end + chip drivers/intel/mipi_camera + register "acpi_uid" = "1" + register "acpi_name" = ""NVM0"" + register "chip_name" = ""GT24P64E"" + register "device_type" = "INTEL_ACPI_CAMERA_NVM" + + register "nvm_size" = "0x2000" + register "nvm_pagesize" = "1" + register "nvm_readonly" = "1" + register "nvm_width" = "0x10" + register "nvm_compat" = ""atmel,24c64"" + + device i2c 50 on + probe CAMERA UF_720P_WF + probe CAMERA UF_1080P_WF + end + end + end + device ref i2c3 on + chip drivers/i2c/rt5645 + register "hid" = ""10EC5650"" + register "name" = ""RT58"" + register "desc" = ""Realtek RT5650"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + register "cbj_sleeve" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + register "jd_mode" = "2" + device i2c 1a on end + end + end + device ref i2c5 on + chip drivers/i2c/hid + register "generic.hid" = ""PNP0C50"" + register "generic.desc" = ""PRIMAX Touchpad"" + register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "generic.wake" = "GPE0_DW2_14" + register "generic.detect" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 15 on end + end + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + register "enable_cnvi_ddr_rfim" = "true" + register "add_acpi_dma_property" = "true" + device generic 0 on + probe WIFI WIFI_6E + end + end + end + device ref pcie_rp4 on + # PCIe 4 WLAN + register "pch_pcie_rp[PCH_RP(4)]" = "{ + .clk_src = 2, + .clk_req = 2, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + chip drivers/wifi/generic + register "wake" = "GPE0_DW1_03" + register "add_acpi_dma_property" = "true" + device pci 00.0 on + probe WIFI WIFI_6 + end + end + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + use usb2_port1 as usb2_port + use tcss_usb3_port2 as usb3_port + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + use usb2_port2 as usb2_port + use tcss_usb3_port1 as usb3_port + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref tcss_usb3_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref tcss_usb3_port1 on end + end + end + end + end + device ref xhci on + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C MB (7.5 inch) + register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C DB (7.1 inch) + register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Type-A MB (6.4 inch) + register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # Type-A DB (6.2 inch) + register "usb2_ports[4]" = "USB2_PORT_SHORT(OC_SKIP)" # LTE (3.3 inch) + register "usb2_ports[5]" = "USB2_PORT_SHORT(OC_SKIP)" # UFC (3.7 inch) + register "usb2_ports[7]" = "USB2_PORT_SHORT(OC_SKIP)" # Bluetooth port for PCIe WLAN (2.5 inch) + register "usb2_ports[9]" = "USB2_PORT_SHORT(OC_SKIP)" # Bluetooth port for CNVi WLAN + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 Type-A port A0(MLB)) + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 Type-A port A1(DB) + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 WWAN(LTE) + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A1 (DB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" + device ref usb2_port4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 LTE"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port5 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 UFC"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""PCIe Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port8 on + probe WIFI WIFI_6 + end + end + chip drivers/usb/acpi + register "desc" = ""CNVi Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on + probe WIFI WIFI_6E + end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A1 (DB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" + device ref usb3_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb3_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 WLAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb3_port4 on end + end + end + end + end + device ref pcie_rp7 off end # SDCard + device ref hda on + chip drivers/sof + register "spkr_tplg" = "rt5650_sp" + register "jack_tplg" = "rt5650_hp" + register "mic_tplg" = "_2ch_pdm0" + device generic 0 on end + end + end + end +end |