diff options
Diffstat (limited to 'src/mainboard/google/brya/variants/osiris/overridetree.cb')
| -rw-r--r-- | src/mainboard/google/brya/variants/osiris/overridetree.cb | 350 |
1 files changed, 348 insertions, 2 deletions
diff --git a/src/mainboard/google/brya/variants/osiris/overridetree.cb b/src/mainboard/google/brya/variants/osiris/overridetree.cb index 4f2c04a57a..fbbca28835 100644 --- a/src/mainboard/google/brya/variants/osiris/overridetree.cb +++ b/src/mainboard/google/brya/variants/osiris/overridetree.cb @@ -1,6 +1,352 @@ +fw_config + field KB_BL 0 0 + option KB_BL_ABSENT 0 + option KB_BL_PRESENT 1 + end + field KB_MT 1 1 + option KB_MT_CROS 0 + option KB_MT_RGB 1 + end + field AUDIO 2 3 + option AUDIO_UNKNOWN 0 + option MAX98360_NAU88L25B_I2S 1 + end +end chip soc/intel/alderlake + register "sagv" = "SaGv_Enabled" + + register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable USB2_C1 + register "usb2_ports[3]" = "USB2_PORT_EMPTY" # Disable M.2 WWAN + + register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Disable M.2 WWAN + + # FIVR configurations are disabled since the board doesn't have V1p05 and Vnn + # bypass rails implemented. + register "ext_fivr_settings" = "{ + .configure_ext_fivr = 1, + }" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| I2C0 | Audio | + #| I2C1 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+ + + register "common_soc_config" = "{ + .i2c[0] = { + .speed = I2C_SPEED_FAST, + .rise_time_ns = 650, + .fall_time_ns = 400, + .data_hold_time_ns = 50, + }, + .i2c[1] = { + .early_init = 1, + .speed = I2C_SPEED_FAST, + .rise_time_ns = 600, + .fall_time_ns = 400, + .data_hold_time_ns = 50, + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + .rise_time_ns = 650, + .fall_time_ns = 400, + .data_hold_time_ns = 50, + }, + }" + + device domain 0 on + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""DRAM"" + register "options.tsr[1].desc" = ""Soc"" + register "options.tsr[2].desc" = ""Charger"" + + # TODO: below values are initial reference values only + ## Active Policy + register "policies.active" = "{ + [0] = { + .target = DPTF_CPU, + .thresholds = { + TEMP_PCT(85, 90), + TEMP_PCT(75, 80), + TEMP_PCT(68, 70), + TEMP_PCT(62, 60), + TEMP_PCT(55, 50), + TEMP_PCT(50, 40), + TEMP_PCT(40, 30), + } + }, + [1] = { + .target = DPTF_TEMP_SENSOR_1, + .thresholds = { + TEMP_PCT(60, 90), + TEMP_PCT(55, 80), + TEMP_PCT(52, 70), + TEMP_PCT(48, 60), + TEMP_PCT(44, 50), + TEMP_PCT(40, 40), + TEMP_PCT(36, 30), + } + } + }" + + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 90, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 55, 5000), + [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 55, 5000), + [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 55, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 100, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 18000, + .max_power = 20000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 200, + }, + .pl2 = { + .min_power = 43000, + .max_power = 43000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 1000, + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + ## Fan Performance Control (Percent, Speed, Noise, Power) + register "controls.fan_perf" = "{ + [0] = { 90, 6700, 220, 2200, }, + [1] = { 80, 5800, 180, 1800, }, + [2] = { 70, 5000, 145, 1450, }, + [3] = { 60, 4900, 115, 1150, }, + [4] = { 50, 3838, 90, 900, }, + [5] = { 40, 2904, 55, 550, }, + [6] = { 30, 2337, 30, 300, }, + [7] = { 20, 1608, 15, 150, }, + [8] = { 10, 800, 10, 100, }, + [9] = { 0, 0, 0, 50, } + }" - device domain 0 on - end + ## Fan options + register "options.fan.fine_grained_control" = "1" + register "options.fan.step_size" = "2" + device generic 0 alias dptf_policy on end + end + end + device ref tbt_pcie_rp0 off end + device ref tbt_pcie_rp1 off end + device ref tbt_pcie_rp2 off end + device ref tcss_dma0 off end + device ref tcss_dma1 off end + device ref pcie4_0 on + # Enable CPU PCIE RP 1 using CLK 0 + register "cpu_pcie_rp[CPU_RP(1)]" = "{ + .clk_req = 0, + .clk_src = 0, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + device generic 0 on end + end + end + device ref i2c0 on + chip drivers/i2c/nau8825 + register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "0" + register "jkdet_pull_up" = "0" + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x0C" + register "sar_threshold[1]" = "0x1C" + register "sar_threshold[2]" = "0x38" + register "sar_threshold[3]" = "0x60" + register "sar_hysteresis" = "1" + register "sar_voltage" = "6" + register "sar_compare_time" = "0" # 500ns + register "sar_sampling_time" = "0" # 2us + register "short_key_debounce" = "2" # 100ms + register "jack_insert_debounce" = "7" # 512ms + register "jack_eject_debounce" = "7" # 512ms + device i2c 1a on + probe AUDIO MAX98360_NAU88L25B_I2S + end + end + end #I2C0 + device ref i2c1 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" + device i2c 50 on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "probed" = "1" + device i2c 15 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""PNP0C50"" + register "generic.desc" = ""Synaptics Touchpad"" + register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "generic.wake" = "GPE0_DW2_14" + register "generic.probed" = "1" + register "hid_desc_reg_offset" = "0x20" + device i2c 0x2c on end + end + end + device ref hda on + chip drivers/generic/max98357a + register "hid" = ""MX98360A"" + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + register "sdmode_delay" = "5" + device generic 0 on + probe AUDIO MAX98360_NAU88L25B_I2S + end + end + end + device ref pcie_rp6 off end # PCIE6 WWAN + device ref pcie_rp7 on + chip drivers/net + register "wake" = "GPE0_DW0_07" + register "led_feature" = "0xe0" + register "customized_led0" = "0x23f" + register "customized_led2" = "0x028" + register "enable_aspm_l1_2" = "1" + device pci 00.0 on end + end + # Enable PCIE 7 using clk 6 + register "pch_pcie_rp[PCH_RP(7)]" = "{ + .clk_src = 6, + .clk_req = 6, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + end # RTL8125 Ethernet NIC + device ref pcie_rp8 off end # PCIE8 SD card + device ref pcie_rp9 off end # PCIE9-12 SSD + device ref gspi1 off end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + use usb2_port1 as usb2_port + use tcss_usb3_port1 as usb3_port + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + use usb2_port3 as usb2_port + use tcss_usb3_port3 as usb3_port + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" + device ref tcss_usb3_port3 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(1, 2))" + device ref usb2_port9 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(1, 2))" + device ref usb3_port1 on end + end + end + end + end + end end |