diff options
Diffstat (limited to 'src/mainboard/elmex/pcm205400/devicetree.cb')
| -rw-r--r-- | src/mainboard/elmex/pcm205400/devicetree.cb | 136 |
1 files changed, 0 insertions, 136 deletions
diff --git a/src/mainboard/elmex/pcm205400/devicetree.cb b/src/mainboard/elmex/pcm205400/devicetree.cb deleted file mode 100644 index bce8a2224a..0000000000 --- a/src/mainboard/elmex/pcm205400/devicetree.cb +++ /dev/null @@ -1,136 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only - -chip northbridge/amd/agesa/family14/root_complex - device cpu_cluster 0 on - chip cpu/amd/agesa/family14 - device lapic 0 on end - end - end - device domain 0 on - subsystemid 0x1022 0x1510 inherit - chip northbridge/amd/agesa/family14 - device pci 0.0 on end # Root Complex - device pci 1.0 on end # Internal Graphics P2P bridge 0x980[2456] - device pci 4.0 on end # PCIE P2P bridge on-board NIC - device pci 5.0 off end # PCIE P2P bridge - device pci 6.0 on end # PCIE P2P bridge PCIe slot - device pci 7.0 off end # PCIE P2P bridge - device pci 8.0 off end # NB/SB Link P2P bridge - end # agesa northbridge - - chip southbridge/amd/cimx/sb800 - device pci 11.0 on end # SATA - device pci 12.0 on end # OHCI USB 0-4 - device pci 12.2 on end # EHCI USB 0-4 - device pci 13.0 on end # OHCI USB 5-9 - device pci 13.2 on end # EHCI USB 5-9 - device pci 14.0 on end # SM - device pci 14.1 on end # IDE 0x439c - device pci 14.2 off end # HDA 0x4383 - device pci 14.3 on # LPC 0x439d - chip superio/fintek/f81865f - device pnp 4e.0 off # Floppy - io 0x60 = 0x3f0 - irq 0x70 = 6 - drq 0x74 = 2 - end - device pnp 4e.3 off end # Parallel Port - device pnp 4e.4 off end # Hardware Monitor - device pnp 4e.5 off end # Keyboard - device pnp 4e.6 off end # GPIO - device pnp 4e.a off end # PME - device pnp 4e.10 on # COM1 - io 0x60 = 0x3f8 - irq 0x70 = 4 - end - device pnp 4e.11 on # COM2 - io 0x60 = 0x2f8 - irq 0x70 = 3 - end - end # f81865f - end #LPC - device pci 14.4 on end # PCIB 0x4384, NOTE: PCI interface pins shared with GPIO {GPIO 35:0} - device pci 14.5 off end # OHCI FS/LS USB - device pci 14.6 off end # Hudson-E1 GbE MAC: Broadcom BCM5785 (14E4:1699) - device pci 15.0 off end # PCIe PortA - device pci 15.1 off end # PCIe PortB - device pci 15.2 off end # PCIe PortC - device pci 15.3 off end # PCIe PortD - device pci 16.0 off end # OHCI USB 10-13 - device pci 16.2 off end # EHCI USB 10-13 - - register "gpp_configuration" = "0" #4:0:0:0 (really need to disable all 4 somehow) - register "boot_switch_sata_ide" = "0" # 0: boot from SATA. 1: IDE - - #set up SB800 Fan control registers and IMC fan controls - register "imc_port_address" = "0x6E" # 0x2E and 0x6E are common - register "fan0_enabled" = "1" - register "fan1_enabled" = "1" - register "imc_fan_zone0_enabled" = "1" - register "imc_fan_zone1_enabled" = "1" - - register "fan0_config_vals" = "{ \ - FAN_INPUT_INTERNAL_DIODE, FAN_POLARITY_HIGH, \ - FREQ_25KHZ, 0x08, 0x00, 0x00, 0x00, 0x00,\ - 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }" - register "fan1_config_vals" = "{ \ - FAN_INPUT_INTERNAL_DIODE, FAN_POLARITY_HIGH, \ - FREQ_25KHZ, 0x10, 0x00, 0x00, 0x00, 0x00, \ - 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }" - - register "imc_zone0_mode1" = " \ - IMC_MODE1_FAN_ENABLED | IMC_MODE1_FAN_IMC_CONTROLLED | \ - IMC_MODE1_FAN_STEP_MODE | IMC_MODE1_FANOUT0" - register "imc_zone0_mode2" = " IMC_MODE2_TEMPIN_SB_TSI | \ - IMC_MODE2_FANIN0 | IMC_MODE2_TEMP_AVERAGING_DISABLED" - register "imc_zone0_temp_offset" = "0x00" # No temp offset - register "imc_zone0_hysteresis" = "0x05" # Degrees C Hysteresis - register "imc_zone0_smbus_addr" = "0x98" # Temp Sensor SMBus address - register "imc_zone0_smbus_num" = "IMC_TEMP_SENSOR_ON_SMBUS_3" # SMBUS number - register "imc_zone0_pwm_step" = "0x01" # Fan PWM stepping rate - register "imc_zone0_ramping" = "0x00" # Disable Fan PWM ramping and stepping - - register "imc_zone1_mode1" = " \ - IMC_MODE1_FAN_ENABLED | IMC_MODE1_FAN_IMC_CONTROLLED | \ - IMC_MODE1_FAN_STEP_MODE | IMC_MODE1_FANOUT1" - register "imc_zone1_mode2" = " IMC_MODE2_TEMPIN_SB_TSI | \ - IMC_MODE2_FANIN1 | IMC_MODE2_TEMP_AVERAGING_DISABLED" - register "imc_zone1_temp_offset" = "0x00" # No temp offset - register "imc_zone1_hysteresis" = "0x05" # Degrees C Hysteresis - register "imc_zone1_smbus_addr" = "0x98" # Temp Sensor SMBus address - register "imc_zone1_smbus_num" = "IMC_TEMP_SENSOR_ON_SMBUS_3" # SMBUS number - register "imc_zone1_pwm_step" = "0x01" # Fan PWM stepping rate - register "imc_zone1_ramping" = "0x00" # Disable Fan PWM ramping and stepping - - # T56N has a Maximum operating temperature of 90C - # ZONEX_THRESHOLDS - _AC0 - _AC7, _CRT - Temp Threshold in degrees C - # ZONEX_FANSPEEDS - Fan speeds as a "percentage" - register "imc_zone0_thresholds" = "{ 87, 82, 77, 72, 65, 1, 0, 0, 90 }" - register "imc_zone0_fanspeeds" = "{100, 7, 5, 4, 3, 2, 0, 0 }" - register "imc_zone1_thresholds" = "{ 85, 80, 75, 65, 1, 0, 0, 0, 90 }" - register "imc_zone1_fanspeeds" = "{100, 10, 6, 4, 3, 0, 0, 0 }" - - end #southbridge/amd/cimx/sb800 - - chip northbridge/amd/agesa/family14 - - # These seem unnecessary - device pci 18.0 on end - device pci 18.1 on end - device pci 18.2 on end - device pci 18.3 on end - device pci 18.4 on end - device pci 18.5 on end - device pci 18.6 on end - device pci 18.7 on end - - register "spdAddrLookup" = " - { - { {0xA0, 0xA2}, {0x00, 0x00}, }, // socket 0 - Channel 0 & 1 - 8-bit SPD addresses - { {0x00, 0x00}, {0x00, 0x00}, }, // socket 1 - Channel 0 & 1 - 8-bit SPD addresses - }" - - end # agesa northbridge - - end #domain -end #northbridge/amd/agesa/family14/root_complex |