diff options
Diffstat (limited to 'src/mainboard/asrock')
| -rw-r--r-- | src/mainboard/asrock/imb-a180/Kconfig | 1 | ||||
| -rw-r--r-- | src/mainboard/asrock/imb-a180/romstage.c | 96 |
2 files changed, 12 insertions, 85 deletions
diff --git a/src/mainboard/asrock/imb-a180/Kconfig b/src/mainboard/asrock/imb-a180/Kconfig index d0c836d9dc..e118bfbe60 100644 --- a/src/mainboard/asrock/imb-a180/Kconfig +++ b/src/mainboard/asrock/imb-a180/Kconfig @@ -17,7 +17,6 @@ if BOARD_ASROCK_IMB_A180 config BOARD_SPECIFIC_OPTIONS # dummy def_bool y - select AGESA_LEGACY select CPU_AMD_AGESA_FAMILY16_KB select NORTHBRIDGE_AMD_AGESA_FAMILY16_KB select SOUTHBRIDGE_AMD_AGESA_YANGTZE diff --git a/src/mainboard/asrock/imb-a180/romstage.c b/src/mainboard/asrock/imb-a180/romstage.c index db84537044..5adcae3be6 100644 --- a/src/mainboard/asrock/imb-a180/romstage.c +++ b/src/mainboard/asrock/imb-a180/romstage.c @@ -21,39 +21,21 @@ #include <arch/io.h> #include <arch/stages.h> #include <device/pnp_def.h> -#include <arch/cpu.h> -#include <cpu/x86/lapic.h> #include <console/console.h> #include <commonlib/loglevel.h> -#include <cpu/amd/car.h> -#include <northbridge/amd/agesa/agesawrapper.h> -#include <northbridge/amd/agesa/agesa_helper.h> -#include <cpu/x86/bist.h> -#include <cpu/x86/lapic.h> + +#include <northbridge/amd/agesa/state_machine.h> #include <southbridge/amd/agesa/hudson/hudson.h> -#include <cpu/amd/agesa/s3_resume.h> -#include "cbmem.h" + #include <superio/winbond/common/winbond.h> #include <superio/winbond/w83627uhg/w83627uhg.h> #define SERIAL_DEV PNP_DEV(0x2e, W83627UHG_SP1) - -void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) +void board_BeforeAgesa(struct sysinfo *cb) { - u32 val, t32; - u32 *addr32; - - /* In Hudson RRG, PMIOxD2[5:4] is "Drive strength control for - * LpcClk[1:0]". To be consistent with Parmer, setting to 4mA - * even though the register is not documented in the Kabini BKDG. - * Otherwise the serial output is bad code. - */ - //outb(0xD2, 0xcd6); - //outb(0x00, 0xcd7); - - /* Must come first to enable PCI MMCONF. */ - amd_initmmio(); + volatile u32 *addr32; + u32 t32; /* Set LPC decode enables. */ pci_devfn_t dev = PCI_DEV(0, 0x14, 3); @@ -65,6 +47,10 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) outb(0x24, 0xcd6); outb(0x1, 0xcd7); + /* Disable PCI-PCI bridge and release GPIO32/33 for other uses. */ + outb(0xea, 0xcd6); + outb(0x1, 0xcd7); + /* Set auxiliary output clock frequency on OSCOUT1 pin to be 48MHz */ addr32 = (u32 *)0xfed80e28; t32 = *addr32; @@ -77,64 +63,6 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) t32 &= 0xffffbffb; *addr32 = t32; - if (!cpu_init_detectedx && boot_cpu()) { - post_code(0x30); - post_code(0x31); - - /* w83627uhg has a default clk of 48MHz, p.9 of data-sheet */ - winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); - - console_init(); - } - - /* Halt if there was a built in self test failure */ - post_code(0x34); - report_bist_failure(bist); - - /* Load MPB */ - val = cpuid_eax(1); - printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val); - printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx); - - /* On Larne, after LpcClkDrvSth is set, it needs some time to be stable, because of the buffer ICS551M */ - int i; - for(i = 0; i < 200000; i++) - val = inb(0xcd6); - - post_code(0x37); - agesawrapper_amdinitreset(); - post_code(0x38); - printk(BIOS_DEBUG, "Got past yangtze_early_setup\n"); - - post_code(0x39); - - agesawrapper_amdinitearly(); - int s3resume = acpi_is_wakeup_s3(); - if (!s3resume) { - post_code(0x40); - agesawrapper_amdinitpost(); - post_code(0x41); - agesawrapper_amdinitenv(); - /* TODO: Disable cache is not ok. */ - disable_cache_as_ram(); - } else { /* S3 detect */ - printk(BIOS_INFO, "S3 detected\n"); - - post_code(0x60); - agesawrapper_amdinitresume(); - - amd_initcpuio(); - agesawrapper_amds3laterestore(); - - post_code(0x61); - prepare_for_resume(); - } - - outb(0xEA, 0xCD6); - outb(0x1, 0xcd7); - - post_code(0x50); - copy_and_run(); - - post_code(0x54); /* Should never see this post code. */ + /* w83627uhg has a default clk of 48MHz, p.9 of data-sheet */ + winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); } |