diff options
Diffstat (limited to 'src/mainboard/Iwill/DK8HTX/Options.lb')
| -rw-r--r-- | src/mainboard/Iwill/DK8HTX/Options.lb | 215 |
1 files changed, 0 insertions, 215 deletions
diff --git a/src/mainboard/Iwill/DK8HTX/Options.lb b/src/mainboard/Iwill/DK8HTX/Options.lb deleted file mode 100644 index c0a1043c16..0000000000 --- a/src/mainboard/Iwill/DK8HTX/Options.lb +++ /dev/null @@ -1,215 +0,0 @@ -uses HAVE_MP_TABLE -uses HAVE_PIRQ_TABLE -uses USE_FALLBACK_IMAGE -uses HAVE_FALLBACK_BOOT -uses HAVE_HARD_RESET -uses IRQ_SLOT_COUNT -uses HAVE_OPTION_TABLE -uses CONFIG_MAX_CPUS -uses CONFIG_MAX_PHYSICAL_CPUS -uses CONFIG_IOAPIC -uses CONFIG_SMP -uses FALLBACK_SIZE -uses ROM_SIZE -uses ROM_SECTION_SIZE -uses ROM_IMAGE_SIZE -uses ROM_SECTION_SIZE -uses ROM_SECTION_OFFSET -uses CONFIG_ROM_STREAM -uses CONFIG_ROM_STREAM_START -uses PAYLOAD_SIZE -uses _ROMBASE -uses XIP_ROM_SIZE -uses XIP_ROM_BASE -uses STACK_SIZE -uses HEAP_SIZE -uses USE_OPTION_TABLE -uses LB_CKS_RANGE_START -uses LB_CKS_RANGE_END -uses LB_CKS_LOC -uses MAINBOARD -uses MAINBOARD_PART_NUMBER -uses MAINBOARD_VENDOR -uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID -uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID -uses LINUXBIOS_EXTRA_VERSION -uses _RAMBASE -uses TTYS0_BAUD -uses TTYS0_BASE -uses TTYS0_LCS -uses DEFAULT_CONSOLE_LOGLEVEL -uses MAXIMUM_CONSOLE_LOGLEVEL -uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL -uses CONFIG_CONSOLE_SERIAL8250 -uses HAVE_INIT_TIMER -uses CONFIG_GDB_STUB -uses CROSS_COMPILE -uses CC -uses HOSTCC -uses OBJCOPY - -uses CONFIG_USE_INIT - -## ROM_SIZE is the size of boot ROM that this board will use. -default ROM_SIZE=524288 - -### -### Build options -### - -## -## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use -## -default FALLBACK_SIZE=0x40000 - -## -## Build code for the fallback boot -## -default HAVE_FALLBACK_BOOT=1 - -## -## Build code to reset the motherboard from linuxBIOS -## -default HAVE_HARD_RESET=1 - -## -## Build code to export a programmable irq routing table -## -default HAVE_PIRQ_TABLE=1 -default IRQ_SLOT_COUNT=9 - -## -## Build code to export an x86 MP table -## Useful for specifying IRQ routing values -## -default HAVE_MP_TABLE=1 - -## -## Build code to export a CMOS option table -## -default HAVE_OPTION_TABLE=1 - -## -## Move the default LinuxBIOS cmos range off of AMD RTC registers -## -default LB_CKS_RANGE_START=49 -default LB_CKS_RANGE_END=122 -default LB_CKS_LOC=123 - -## -## Build code for SMP support -## Only worry about 2 micro processors -## -default CONFIG_SMP=1 -default CONFIG_MAX_CPUS=2 -default CONFIG_MAX_PHYSICAL_CPUS=2 - -## -## Build code to setup a generic IOAPIC -## -default CONFIG_IOAPIC=1 - -## -## Clean up the motherboard id strings -## -default MAINBOARD_PART_NUMBER="HDAMA" -default MAINBOARD_VENDOR="ARIMA" -default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f -default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016 - - -### -### LinuxBIOS layout values -### - -## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. -default ROM_IMAGE_SIZE = 65536 - -## -## Use a small 8K stack -## -default STACK_SIZE=0x2000 - -## -## Use a small 16K heap -## -default HEAP_SIZE=0x4000 - -## -## Only use the option table in a normal image -## -default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE - -## -## LinuxBIOS C code runs at this location in RAM -## -default _RAMBASE=0x00004000 - -## -## Load the payload from the ROM -## -default CONFIG_ROM_STREAM = 1 - -### -### Defaults of options that you may want to override in the target config file -### - -## -## The default compiler -## -#default CC="$(CROSS_COMPILE)gcc -m32" -#default HOSTCC="gcc" - -## -## Disable the gdb stub by default -## -default CONFIG_GDB_STUB=0 - -## -## The Serial Console -## - -# To Enable the Serial Console -default CONFIG_CONSOLE_SERIAL8250=1 - -## Select the serial console baud rate -default TTYS0_BAUD=115200 -#default TTYS0_BAUD=57600 -#default TTYS0_BAUD=38400 -#default TTYS0_BAUD=19200 -#default TTYS0_BAUD=9600 -#default TTYS0_BAUD=4800 -#default TTYS0_BAUD=2400 -#default TTYS0_BAUD=1200 - -# Select the serial console base port -default TTYS0_BASE=0x3f8 - -# Select the serial protocol -# This defaults to 8 data bits, 1 stop bit, and no parity -default TTYS0_LCS=0x3 - -## -### Select the linuxBIOS loglevel -## -## EMERG 1 system is unusable -## ALERT 2 action must be taken immediately -## CRIT 3 critical conditions -## ERR 4 error conditions -## WARNING 5 warning conditions -## NOTICE 6 normal but significant condition -## INFO 7 informational -## DEBUG 8 debug-level messages -## SPEW 9 Way too many details - -## Request this level of debugging output -default DEFAULT_CONSOLE_LOGLEVEL=8 -## At a maximum only compile in this level of debugging -default MAXIMUM_CONSOLE_LOGLEVEL=8 - -## -## Select power on after power fail setting -default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" - -### End Options.lb -end |