diff options
Diffstat (limited to 'Documentation/mainboard')
| -rw-r--r-- | Documentation/mainboard/lenovo/montevina_series.md | 6 | ||||
| -rw-r--r-- | Documentation/mainboard/starlabs/common/building.md | 10 | ||||
| -rw-r--r-- | Documentation/mainboard/starlabs/common/flashing.md | 4 |
3 files changed, 10 insertions, 10 deletions
diff --git a/Documentation/mainboard/lenovo/montevina_series.md b/Documentation/mainboard/lenovo/montevina_series.md index e4e5da3c5f..120a161e90 100644 --- a/Documentation/mainboard/lenovo/montevina_series.md +++ b/Documentation/mainboard/lenovo/montevina_series.md @@ -46,7 +46,7 @@ Now you need to patch the flash descriptor. You can either [modify the one from your backup with **ifdtool**](#modifying-flash-descriptor-using-ifdtool), or [use one from the coreboot repository](#using-checked-in-flash-descriptor-via-bincfg). -#### Modifying flash descriptor using ifdtool +### Modifying flash descriptor using ifdtool Pick the layout according to your chip size from the table below and save it to the `new_layout.txt` file: @@ -88,7 +88,7 @@ $ mv flashregion_0_flashdescriptor.bin.new.new flashregion_0_flashdescriptor.bin Continue to the [Configuring coreboot](#configuring-coreboot) section. -#### Using checked-in flash descriptor via bincfg +### Using checked-in flash descriptor via bincfg There is a copy of an X200's flash descriptor checked into the coreboot repository. It is supposed to work for the T400/T500 as well. The descriptor @@ -119,7 +119,7 @@ $ make gen-ifd-x200 It will be saved to the `flashregion_0_fd.bin` file. -#### Configuring coreboot +### Configuring coreboot Now configure coreboot. You need to select correct chip size and specify paths to flash descriptor and gbe dump. diff --git a/Documentation/mainboard/starlabs/common/building.md b/Documentation/mainboard/starlabs/common/building.md index 3b9b568b74..c283ef54ef 100644 --- a/Documentation/mainboard/starlabs/common/building.md +++ b/Documentation/mainboard/starlabs/common/building.md @@ -1,15 +1,15 @@ -## Building coreboot +# Building coreboot -### Preliminaries +## Preliminaries Prior to building coreboot the following files are required: -#### StarBook series: +### StarBook series: * Intel Flash Descriptor file (descriptor.bin) * Intel Management Engine firmware (me.bin) * ITE Embedded Controller firmware (ec.bin) -#### StarLite series: +### StarLite series: * Intel Flash Descriptor file (descriptor.bin) * IFWI Image (ifwi.rom) @@ -18,7 +18,7 @@ The files listed below are optional: These files exist in the correct location in the [StarLabsLtd/blobs](https://github.com/StarLabsLtd/blobs) repo on GitHub which is used in place of the standard 3rdparty/blobs repo. -### Build +## Build The following commands will build a working image, where the last two words represent the series and processor i.e. `lite_glkr`: diff --git a/Documentation/mainboard/starlabs/common/flashing.md b/Documentation/mainboard/starlabs/common/flashing.md index c5764b9d6d..46b98afeae 100644 --- a/Documentation/mainboard/starlabs/common/flashing.md +++ b/Documentation/mainboard/starlabs/common/flashing.md @@ -1,6 +1,6 @@ # Flashing with fwupd -#### **Requirements:** +## **Requirements:** * fwupd version 1.5.6 or later * The battery must be charged to at least 30% @@ -44,7 +44,7 @@ BIOS Lock must be disabled when switching from the standard AMI (American Megatr 4\. Next, press the `F10` key to **Save & Exit** and then `Enter` to confirm. -#### **Switching Branch** +## **Switching Branch** Switching branch refers to changing from AMI firmware to coreboot, or vice versa. |