diff options
Diffstat (limited to 'Documentation/Intel')
| -rw-r--r-- | Documentation/Intel/index.html | 1 | ||||
| -rw-r--r-- | Documentation/Intel/vboot.html | 402 |
2 files changed, 0 insertions, 403 deletions
diff --git a/Documentation/Intel/index.html b/Documentation/Intel/index.html index b4daa960a9..9d8aad05e9 100644 --- a/Documentation/Intel/index.html +++ b/Documentation/Intel/index.html @@ -29,7 +29,6 @@ </li> <li><a target="_blank" href="SoC/soc.html">SoC</a> support</li> <li><a target="_blank" href="Board/board.html">Board</a> support</li> - <li><a target="_blank" href="vboot.html">Verified Boot (vboot)</a> support</li> </ul> diff --git a/Documentation/Intel/vboot.html b/Documentation/Intel/vboot.html deleted file mode 100644 index ca49ac2e2d..0000000000 --- a/Documentation/Intel/vboot.html +++ /dev/null @@ -1,402 +0,0 @@ -<!DOCTYPE html> -<html> - <head> - <title>vboot - Verified Boot Support</title> - </head> - <body> - -<h1>vboot - Verified Boot Support</h1> - -<p> -Google's verified boot support consists of: -</p> -<ul> - <li>A root of trust</li> - <li>Special firmware layout</li> - <li>Firmware verification</li> - <li>Firmware measurements</li> - <li>A firmware update mechanism</li> - <li>Specific build flags</li> - <li>Signing the coreboot image</li> -</ul> - -Google's vboot verifies the firmware and places measurements -within the TPM. - -<hr> -<h2>Root of Trust</h2> -<p> -When using vboot, the root-of-trust is basically the read-only portion of the -SPI flash. The following items factor into the trust equation: -</p> -<ul> - <li>The GCC compiler must reliably translate the code into machine code - without inserting any additional code (virus, backdoor, etc.) - </li> - <li>The CPU must reliably execute the reset sequence and instructions as - documented by the CPU manufacturer. - </li> - <li>The SPI flash must provide only the code programmed into it to the CPU - without providing any alternative reset vector or code sequence. - </li> - <li>The SPI flash must honor the write-protect input and protect the - specified portion of the SPI flash from all erase and write accesses. - </li> -</ul> - -<p> -The firmware is typically protected using the write-protect pin on the SPI -flash part and setting some of the write-protect bits in the status register -during manufacturing. The protected area is platform specific and for x86 -platforms is typically 1/4th of the SPI flash -part size. Because this portion of the SPI flash is hardware write protected, -it is not possible to update this portion of the SPI flash in the field, -without altering the system to eliminate the ground connection to the SPI flash -write-protect pin. Without hardware modifications, this portion of the SPI -flash maintains the manufactured state during the system's lifetime. -</p> - -<hr> -<h2>Firmware Layout</h2> -<p> -Several sections are added to the firmware layout to support vboot: -</p> -<ul> - <li>Read-only section</li> - <li>Google Binary Blob (GBB) area</li> - <li>Read/write section A</li> - <li>Read/write section B</li> -</ul> -<p> -The following sections describe the various portions of the flash layout. -</p> - -<h3>Read-Only Section</h3> -<p> -The read-only section contains a coreboot file system (CBFS) that contains all -of the boot firmware necessary to perform recovery for the system. This -firmware is typically protected using the write-protect pin on the SPI flash -part and setting some of the write-protect bits in the status register during -manufacturing. The protected area is typically 1/4th of the SPI flash part -size and must cover the entire read-only section which consists of: -</p> -<ul> - <li>Vital Product Data (VPD) area</li> - <li>Firmware ID area</li> - <li>Google Binary Blob (GBB) area</li> - <li>coreboot file system containing read-only recovery firmware</li> -</ul> - -<h3>Google Binary Blob (GBB) Area</h3> -<p> -The GBB area is part of the read-only section. This area contains a 4096 or -8192 bit public root RSA key that is used to verify the VBLOCK area to obtain -the firmware signing key. -</p> - -<h3>Recovery Firmware</h3> -<p> -The recovery firmware is contained within a coreboot file system and consists -of: -</p> -<ul> - <li>reset vector</li> - <li>bootblock</li> - <li>verstage</li> - <li>romstage</li> - <li>postcar</li> - <li>ramstage</li> - <li>payload</li> - <li>flash map file</li> - <li>config file</li> - <li>processor specific files: - <ul> - <li>Microcode</li> - <li>fspm.bin</li> - <li>fsps.bin</li> - </ul> - </li> -</ul> - -<p> -The recovery firmware is written during manufacturing and typically contains -code to write the storage device (eMMC device or hard disk). The recovery -image is usually contained on a socketed device such as a USB flash drive or -an SD card. Depending upon the payload firmware doing the recovery, it may -be possible for the user to interact with the system to specify the recovery -image path. Part of the recovery is also to write the A and B areas of the -SPI flash device to boot the system. -</p> - - -<h3>Read/Write Section</h3> - -<p> -The read/write sections contain an area which contains the firmware signing -key and signature and an area containing a coreboot file system with a subset -of the firmware. The firmware files in FW_MAIN_A and FW_MAIN_B are: -</p> -<ul> - <li>romstage</li> - <li>postcar</li> - <li>ramstage</li> - <li>payload</li> - <li>config file</li> - <li>processor specific files: - <ul> - <li>Microcode</li> - <li>fspm.bin</li> - <li>fsps.bin</li> - </ul> - </li> -</ul> - -<p> -The firmware subset enables most issues to be fixed in the field with firmware -updates. The firmware files handle memory and most of silicon initialization. -These files also produce the tables which get passed to the operating system. -</p> - -<hr> -<h2>Firmware Updates</h2> -<p> -The read/write sections exist in one of three states: -</p> -<ul> - <li>Invalid</li> - <li>Ready to boot</li> - <li>Successfully booted</li> -</ul> - -<table border="1"> -<tr bgcolor="#ffc0c0"> -<td> -Where is this state information written? -<br/>CMOS? -<br/>RW_NVRAM? -<br/>RW_FWID_* -</td> -</tr> -</table> - -<p> -Firmware updates are handled by the operating system by writing any read/write -section that is not in the "successfully booted" state. Upon the next reboot, -vboot determines the section to boot. If it finds one in the "ready to boot" -state then it attempts to boot using that section. If the boot fails then -vboot marks the section as invalid and attempts to fall back to a read/write -section in the "successfully booted" state. If vboot is not able to find a -section in the "successfully booted" state then vboot enters recovery mode. -</p> - -<p> -Only the operating system is able to transition a section from the "ready to -boot" state to the "successfully booted" state. The transition is typically -done after the operating system has been running for a while indicating -that successful boot was possible and the operating system is stable. -</p> - -<p> -Note that as long as the SPI write protection is in place then the system is -always recoverable. If the flash update fails then the system will continue -to boot using the previous read/write area. The same is true if coreboot -passes control to the payload or the operating system and then the boot fails. -In the worst case, the SPI flash gets totally corrupted in which case vboot -fails the signature checks and enters recovery mode. There are no times where -the SPI flash is exposed and the reset vector or part of the recovery firmware -gets corrupted. -</p> - -<hr> -<h2>Build Flags</h2> -<p> -The following Kconfig values need to be selected to enable vboot: -</p> -<ul> - <li>COLLECT_TIMESTAMPS</li> - <li>VBOOT</li> -</ul> - -<p> -The starting stage needs to be specified by selecting either -VBOOT_STARTS_IN_BOOTBLOCK or VBOOT_STARTS_IN_ROMSTAGE. -</p> - -<p> -If vboot starts in bootblock then vboot may be built as a separate stage by -selecting VBOOT_SEPARATE_VERSTAGE. Additionally, if static RAM is too small -to fit both verstage and romstage then selecting VBOOT_RETURN_FROM_VERSTAGE -enables bootblock to reuse the RAM occupied by verstage for romstage. -</p> - -<p> -Non-volatile flash is needed for vboot operation. This flash area may be in -CMOS, the EC, or in a read/write area of the SPI flash device. Select one of -the following: -</p> -<ul> - <li>VBOOT_VBNV_CMOS</li> - <li>VBOOT_VBNV_EC</li> - <li>VBOOT_VBNV_FLASH</li> -</ul> -<p> -More non-volatile storage features may be found in src/vboot/Kconfig. -</p> - -<p> -A TPM is also required for vboot operation. TPMs are available in -drivers/i2c/tpm and drivers/pc80/tpm. -</p> - -<p> -In addition to adding the coreboot files into the read-only region, enabling -vboot causes the build script to add the read/write files into coreboot file -systems in FW_MAIN_A and FW_MAIN_B. -</p> - -<hr> -<h2>Signing the coreboot Image</h2> -<p> -The following command script is an example of how to sign the coreboot image file. -This script is used on the Intel Galileo board and creates the GBB area and -inserts it into the coreboot image. It also updates the VBLOCK areas with the -firmware signing key and the signature for the FW_MAIN firmware. More details -are available in 3rdparty/vboot/README. -</p> - -<pre><code>#!/bin/sh -# -# The necessary tools were built and installed using the following commands: -# -# pushd 3rdparty/vboot -# make -# sudo make install -# popd -# -# The keys were made using the following command -# -# 3rdparty/vboot/scripts/keygeneration/create_new_keys.sh \ -# --4k --4k-root --output $PWD/keys -# -# -# The "magic" numbers below are derived from the GBB section in -# src/mainboard/intel/galileo/vboot.fmd. -# -# GBB Header Size: 0x80 -# GBB Offset: 0x611000, 4KiB block number: 1553 (0x611) -# GBB Length: 0x7f000, 4KiB blocks: 127 (0x7f) -# COREBOOT Offset: 0x690000, 4KiB block number: 1680 (0x690) -# COREBOOT Length: 0x170000, 4KiB blocks: 368 (0x170) -# -# 0x7f000 (GBB Length) = 0x80 + 0x100 + 0x1000 + 0x7ce80 + 0x1000 -# -# Create the GBB area blob -# Parameters: hwid_size,rootkey_size,bmpfv_size,recoverykey_size -# -gbb_utility -c 0x100,0x1000,0x7ce80,0x1000 gbb.blob - -# -# Copy from the start of the flash to the GBB region into the signed flash -# image. -# -# 1553 * 4096 = 0x611 * 0x1000 = 0x611000, size of area before GBB -# -dd conv=fdatasync ibs=4096 obs=4096 count=1553 \ - if=build/coreboot.rom of=build/coreboot.signed.rom - -# -# Append the empty GBB area to the coreboot.rom image. -# -# 1553 * 4096 = 0x611 * 0x1000 = 0x611000, offset to GBB -# -dd conv=fdatasync obs=4096 obs=4096 seek=1553 if=gbb.blob \ - of=build/coreboot.signed.rom - -# -# Append the rest of the read-only region into the signed flash image. -# -# 1680 * 4096 = 0x690 * 0x1000 = 0x690000, offset to COREBOOT area -# 368 * 4096 = 0x170 * 0x1000 = 0x170000, length of COREBOOT area -# -dd conv=fdatasync ibs=4096 obs=4096 skip=1680 seek=1680 count=368 \ - if=build/coreboot.rom of=build/coreboot.signed.rom - -# -# Insert the HWID and public root and recovery RSA keys into the GBB area. -# -gbb_utility \ - --set --hwid='Galileo' \ - -r $PWD/keys/recovery_key.vbpubk \ - -k $PWD/keys/root_key.vbpubk \ - build/coreboot.signed.rom - -# -# Sign the read/write firmware areas with the private signing key and update -# the VBLOCK_A and VBLOCK_B regions. -# -3rdparty/vboot/scripts/image_signing/sign_firmware.sh \ - build/coreboot.signed.rom \ - $PWD/keys \ - build/coreboot.signed.rom -</code></pre> - -<hr> -<h2>Boot Flow</h2> -<p> -The reset vector exist in the read-only area and points to the bootblock entry -point. The only copy of the bootblock exists in the read-only area of the SPI -flash. Verstage may be part of the bootblock or a separate stage. If separate -then the bootblock loads verstage from the read-only area and transfers control -to it. -</p> - -<p> -Upon first boot, verstage attempts to verify the read/write section A. It gets -the public root key from the GBB area and uses that to verify the VBLOCK area -in read-write section A. If the VBLOCK area is valid then it extracts the -firmware signing key (1024-8192 bits) and uses that to verify the FW_MAIN_A -area of read/write section A. If the verification is successful then verstage -instructs coreboot to use the coreboot file system in read/write section A for -the contents of the remaining boot firmware (romstage, postcar, ramstage and -the payload). -</p> - -<p> -If verification fails for the read/write area and the other read/write area is -not valid vboot falls back to the read-only area to boot into system recovery. -</p> - -<hr> -<h2>Chromebook Special Features</h2> -<p> -Google's Chromebooks have some special features: -</p> -<ul> - <li>Developer mode</li> - <li>Write-protect screw</li> -</ul> - -<h3>Developer Mode</h3> -<p> -Developer mode allows the user to use coreboot to boot another operating system. -This may be a another (beta) version of Chrome OS, or another flavor of -GNU/Linux. Use of developer mode does not void the system warranty. Upon -entry into developer mode, all locally saved data on the system is lost. -This prevents someone from entering developer mode to subvert the system -security to access files on the local system or cloud. -</p> - -<h3>Write Protect Screw</h3> -<p> -Chromebooks have a write-protect screw which provides the ground to the -write-protect pin of the SPI flash. Google specifically did this to allow -the manufacturing line and advanced developers to re-write the entire SPI flash -part. Once the screw is removed, any firmware may be placed on the device. -However, accessing this screw requires opening the case and voids the system -warranty! -</p> - -<hr> -<p>Modified: 2 May 2017</p> - </body> -</html> |