diff options
| -rw-r--r-- | src/soc/intel/alderlake/Makefile.inc | 5 | ||||
| -rw-r--r-- | src/vendorcode/intel/fsp/fsp2_0/iot/raptorlake_s/MemInfoHob.h | 315 |
2 files changed, 320 insertions, 0 deletions
diff --git a/src/soc/intel/alderlake/Makefile.inc b/src/soc/intel/alderlake/Makefile.inc index c36c7172d5..1da9b3824e 100644 --- a/src/soc/intel/alderlake/Makefile.inc +++ b/src/soc/intel/alderlake/Makefile.inc @@ -70,6 +70,11 @@ endif CPPFLAGS_common += -I$(src)/soc/intel/alderlake CPPFLAGS_common += -I$(src)/soc/intel/alderlake/include +# Include the missing MemInfoHob.h from vendorcode +ifeq ($(CONFIG_SOC_INTEL_RAPTORLAKE_PCH_S)$(CONFIG_FSP_TYPE_IOT),yy) +CPPFLAGS_common += -I$(src)/vendorcode/intel/fsp/fsp2_0/iot/raptorlake_s +endif + ifeq ($(CONFIG_SOC_INTEL_ALDERLAKE_PCH_S),y) # 06-97-00, 06-97-01, 06-97-04 are ADL-S Engineering Samples # 06-97-02 are ADL-S/HX Quality Samples but also ADL-HX Engineering Samples diff --git a/src/vendorcode/intel/fsp/fsp2_0/iot/raptorlake_s/MemInfoHob.h b/src/vendorcode/intel/fsp/fsp2_0/iot/raptorlake_s/MemInfoHob.h new file mode 100644 index 0000000000..989bfb1a95 --- /dev/null +++ b/src/vendorcode/intel/fsp/fsp2_0/iot/raptorlake_s/MemInfoHob.h @@ -0,0 +1,315 @@ +/** @file + This file contains definitions required for creation of + Memory S3 Save data, Memory Info data and Memory Platform + data hobs. + +@copyright + Copyright (c) 2022, Intel Corporation. All rights reserved.<BR> + + SPDX-License-Identifier: BSD-2-Clause-Patent + +@par Specification Reference: +**/ +#ifndef _MEM_INFO_HOB_H_ +#define _MEM_INFO_HOB_H_ + + +#pragma pack (push, 1) + +extern EFI_GUID gSiMemoryS3DataGuid; +extern EFI_GUID gSiMemoryInfoDataGuid; +extern EFI_GUID gSiMemoryPlatformDataGuid; + +#define MAX_NODE 2 +#define MAX_CH 4 +#define MAX_DIMM 2 +// Must match definitions in +// Intel\ClientOneSiliconPkg\IpBlock\MemoryInit\Mtl\Include\MrcInterface.h +#define HOB_MAX_SAGV_POINTS 4 + +/// +/// Host reset states from MRC. +/// +#define WARM_BOOT 2 + +#define R_MC_CHNL_RANK_PRESENT 0x7C +#define B_RANK0_PRS BIT0 +#define B_RANK1_PRS BIT1 +#define B_RANK2_PRS BIT4 +#define B_RANK3_PRS BIT5 + +// @todo remove and use the MdePkg\Include\Pi\PiHob.h +#if !defined(_PEI_HOB_H_) && !defined(__PI_HOB_H__) +#ifndef __HOB__H__ +typedef struct _EFI_HOB_GENERIC_HEADER { + UINT16 HobType; + UINT16 HobLength; + UINT32 Reserved; +} EFI_HOB_GENERIC_HEADER; + +typedef struct _EFI_HOB_GUID_TYPE { + EFI_HOB_GENERIC_HEADER Header; + EFI_GUID Name; + /// + /// Guid specific data goes here + /// +} EFI_HOB_GUID_TYPE; +#endif +#endif + +/// +/// Defines taken from MRC so avoid having to include MrcInterface.h +/// + +// +// Matches MAX_SPD_SAVE define in MRC +// +#ifndef MAX_SPD_SAVE +#define MAX_SPD_SAVE 29 +#endif + +// +// MRC version description. +// +typedef struct { + UINT8 Major; ///< Major version number + UINT8 Minor; ///< Minor version number + UINT8 Rev; ///< Revision number + UINT8 Build; ///< Build number +} SiMrcVersion; + +// +// Matches MrcChannelSts enum in MRC +// +#ifndef CHANNEL_NOT_PRESENT +#define CHANNEL_NOT_PRESENT 0 // There is no channel present on the controller. +#endif +#ifndef CHANNEL_DISABLED +#define CHANNEL_DISABLED 1 // There is a channel present but it is disabled. +#endif +#ifndef CHANNEL_PRESENT +#define CHANNEL_PRESENT 2 // There is a channel present and it is enabled. +#endif + +// +// Matches MrcDimmSts enum in MRC +// +#ifndef DIMM_ENABLED +#define DIMM_ENABLED 0 // DIMM/rank Pair is enabled, presence will be detected. +#endif +#ifndef DIMM_DISABLED +#define DIMM_DISABLED 1 // DIMM/rank Pair is disabled, regardless of presence. +#endif +#ifndef DIMM_PRESENT +#define DIMM_PRESENT 2 // There is a DIMM present in the slot/rank pair and it will be used. +#endif +#ifndef DIMM_NOT_PRESENT +#define DIMM_NOT_PRESENT 3 // There is no DIMM present in the slot/rank pair. +#endif + +// +// Matches MrcBootMode enum in MRC +// +#ifndef __MRC_BOOT_MODE__ +#define __MRC_BOOT_MODE__ //The below values are originated from MrcCommonTypes.h + #ifndef INT32_MAX + #define INT32_MAX (0x7FFFFFFF) + #endif //INT32_MAX +typedef enum { + bmCold, ///< Cold boot + bmWarm, ///< Warm boot + bmS3, ///< S3 resume + bmFast, ///< Fast boot + MrcBootModeMax, ///< MRC_BOOT_MODE enumeration maximum value. + MrcBootModeDelim = INT32_MAX ///< This value ensures the enum size is consistent on both sides of the PPI. +} MRC_BOOT_MODE; +#endif //__MRC_BOOT_MODE__ + +// +// Matches MrcDdrType enum in MRC +// +#ifndef MRC_DDR_TYPE_DDR5 +#define MRC_DDR_TYPE_DDR5 1 +#endif +#ifndef MRC_DDR_TYPE_LPDDR5 +#define MRC_DDR_TYPE_LPDDR5 2 +#endif +#ifndef MRC_DDR_TYPE_LPDDR4 +#define MRC_DDR_TYPE_LPDDR4 3 +#endif +#ifndef MRC_DDR_TYPE_UNKNOWN +#define MRC_DDR_TYPE_UNKNOWN 4 +#endif + +#define MAX_PROFILE_NUM 7 // number of memory profiles supported +#define MAX_XMP_PROFILE_NUM 5 // number of XMP profiles supported + +#define MAX_TRACE_REGION 5 +#define MAX_TRACE_CACHE_TYPE 2 + +// +// DIMM timings +// +typedef struct { + UINT32 tCK; ///< Memory cycle time, in femtoseconds. + UINT16 NMode; ///< Number of tCK cycles for the channel DIMM's command rate mode. + UINT16 tCL; ///< Number of tCK cycles for the channel DIMM's CAS latency. + UINT16 tCWL; ///< Number of tCK cycles for the channel DIMM's minimum CAS write latency time. + UINT16 tFAW; ///< Number of tCK cycles for the channel DIMM's minimum four activate window delay time. + UINT16 tRAS; ///< Number of tCK cycles for the channel DIMM's minimum active to precharge delay time. + UINT16 tRCDtRP; ///< Number of tCK cycles for the channel DIMM's minimum RAS# to CAS# delay time and Row Precharge delay time. + UINT16 tREFI; ///< Number of tCK cycles for the channel DIMM's minimum Average Periodic Refresh Interval. + UINT16 tRFC; ///< Number of tCK cycles for the channel DIMM's minimum refresh recovery delay time. + UINT16 tRFCpb; ///< Number of tCK cycles for the channel DIMM's minimum per bank refresh recovery delay time. + UINT16 tRFC2; ///< Number of tCK cycles for the channel DIMM's minimum refresh recovery delay time. + UINT16 tRFC4; ///< Number of tCK cycles for the channel DIMM's minimum refresh recovery delay time. + UINT16 tRPab; ///< Number of tCK cycles for the channel DIMM's minimum row precharge delay time for all banks. + UINT16 tRRD; ///< Number of tCK cycles for the channel DIMM's minimum row active to row active delay time. + UINT16 tRRD_L; ///< Number of tCK cycles for the channel DIMM's minimum row active to row active delay time for same bank groups. + UINT16 tRRD_S; ///< Number of tCK cycles for the channel DIMM's minimum row active to row active delay time for different bank groups. + UINT16 tRTP; ///< Number of tCK cycles for the channel DIMM's minimum internal read to precharge command delay time. + UINT16 tWR; ///< Number of tCK cycles for the channel DIMM's minimum write recovery time. + UINT16 tWTR; ///< Number of tCK cycles for the channel DIMM's minimum internal write to read command delay time. + UINT16 tWTR_L; ///< Number of tCK cycles for the channel DIMM's minimum internal write to read command delay time for same bank groups. + UINT16 tWTR_S; ///< Number of tCK cycles for the channel DIMM's minimum internal write to read command delay time for different bank groups. + UINT16 tCCD_L; ///< Number of tCK cycles for the channel DIMM's minimum CAS-to-CAS delay for same bank group. +} MRC_CH_TIMING; + +typedef struct { + UINT16 tRDPRE; ///< Read CAS to Precharge cmd delay +} MRC_IP_TIMING; + +/// +/// Memory SMBIOS & OC Memory Data Hob +/// +typedef struct { + UINT8 Status; ///< See MrcDimmStatus for the definition of this field. + UINT8 DimmId; + UINT32 DimmCapacity; ///< DIMM size in MBytes. + UINT16 MfgId; + UINT8 ModulePartNum[20]; ///< Module part number for DDR3 is 18 bytes however for DRR4 20 bytes as per JEDEC Spec, so reserving 20 bytes + UINT8 RankInDimm; ///< The number of ranks in this DIMM. + UINT8 SpdDramDeviceType; ///< Save SPD DramDeviceType information needed for SMBIOS structure creation. + UINT8 SpdModuleType; ///< Save SPD ModuleType information needed for SMBIOS structure creation. + UINT8 SpdModuleMemoryBusWidth; ///< Save SPD ModuleMemoryBusWidth information needed for SMBIOS structure creation. + UINT8 SpdSave[MAX_SPD_SAVE]; ///< Save SPD Manufacturing information needed for SMBIOS structure creation. + UINT16 Speed; ///< The maximum capable speed of the device, in MHz + UINT8 MdSocket; ///< MdSocket: 0 = Memory Down, 1 = Socketed. Needed for SMBIOS structure creation. +} DIMM_INFO; + +typedef struct { + UINT8 Status; ///< Indicates whether this channel should be used. + UINT8 ChannelId; + UINT8 DimmCount; ///< Number of valid DIMMs that exist in the channel. + MRC_CH_TIMING Timing[MAX_PROFILE_NUM]; ///< The channel timing values. + DIMM_INFO DimmInfo[MAX_DIMM]; ///< Save the DIMM output characteristics. +} CHANNEL_INFO; + +typedef struct { + UINT8 Status; ///< Indicates whether this controller should be used. + UINT16 DeviceId; ///< The PCI device id of this memory controller. + UINT8 RevisionId; ///< The PCI revision id of this memory controller. + UINT8 ChannelCount; ///< Number of valid channels that exist on the controller. + CHANNEL_INFO ChannelInfo[MAX_CH]; ///< The following are channel level definitions. +} CONTROLLER_INFO; + +typedef struct { + UINT64 BaseAddress; ///< Trace Base Address + UINT64 TotalSize; ///< Total Trace Region of Same Cache type + UINT8 CacheType; ///< Trace Cache Type + UINT8 ErrorCode; ///< Trace Region Allocation Fail Error code + UINT8 Rsvd[2]; +} PSMI_MEM_INFO; + +/// This data structure contains per-SaGv timing values that are considered output by the MRC. +typedef struct { + UINT32 DataRate; ///< The memory rate for the current SaGv Point in units of MT/s + MRC_CH_TIMING JedecTiming; ///< Timings used for this entry's corresponding SaGv Point - derived from JEDEC SPD spec + MRC_IP_TIMING IpTiming; ///< Timings used for this entry's corresponding SaGv Point - IP specific +} HOB_SAGV_TIMING_OUT; + +/// This data structure contains SAGV config values that are considered output by the MRC. +typedef struct { + UINT32 NumSaGvPointsEnabled; ///< Count of the total number of SAGV Points enabled. + UINT32 SaGvPointMask; ///< Bit mask where each bit indicates an enabled SAGV point. + HOB_SAGV_TIMING_OUT SaGvTiming[HOB_MAX_SAGV_POINTS]; +} HOB_SAGV_INFO; + +typedef struct { + UINT8 Revision; + UINT16 DataWidth; ///< Data width, in bits, of this memory device + /** As defined in SMBIOS 3.0 spec + Section 7.18.2 and Table 75 + **/ + UINT8 MemoryType; ///< DDR type: DDR3, DDR4, or LPDDR3 + UINT16 MaximumMemoryClockSpeed;///< The maximum capable speed of the device, in megahertz (MHz) + UINT16 ConfiguredMemoryClockSpeed; ///< The configured clock speed to the memory device, in megahertz (MHz) + /** As defined in SMBIOS 3.0 spec + Section 7.17.3 and Table 72 + **/ + UINT8 ErrorCorrectionType; + + SiMrcVersion Version; + BOOLEAN EccSupport; + UINT8 MemoryProfile; + UINT8 IsDMBRunning; ///< Deprecated. + UINT32 TotalPhysicalMemorySize; + UINT32 DefaultXmptCK[MAX_XMP_PROFILE_NUM];///< Stores the tCK value read from SPD XMP profiles if they exist. + /// + /// Set of bit flags showing XMP and User Profile capability status for the DIMMs detected in system. For each bit, 1 is supported, 0 is unsupported. + /// Bit 0: XMP Profile 1 capability status + /// Bit 1: XMP Profile 2 capability status + /// Bit 2: XMP Profile 3 capability status + /// Bit 3: User Profile 4 capability status + /// Bit 4: User Profile 5 capability status + /// + UINT8 XmpProfileEnable; + UINT8 XmpConfigWarning; ///< If XMP capable DIMMs config support only 1DPC, but 2DPC is installed + UINT8 Ratio; ///< DDR Frequency Ratio, Max Value 255 + UINT8 RefClk; + UINT32 VddVoltage[MAX_PROFILE_NUM]; + UINT32 VddqVoltage[MAX_PROFILE_NUM]; + UINT32 VppVoltage[MAX_PROFILE_NUM]; + CONTROLLER_INFO Controller[MAX_NODE]; + UINT16 Ratio_UINT16; ///< DDR Frequency Ratio, used for programs that require ratios higher then 255 + UINT32 NumPopulatedChannels; ///< Total number of memory channels populated + HOB_SAGV_INFO SagvConfigInfo; ///< This data structure contains SAGV config values that are considered output by the MRC. + UINT16 TotalMemWidth; ///< Total Memory Width in bits from all populated channels + BOOLEAN MemorySpeedReducedWrongDimmSlot; ///< Can be used by OEM BIOS to display a warning on the screen that DDR speed was reduced due to wrong DIMM population + BOOLEAN MemorySpeedReducedMixedConfig; ///< Can be used by OEM BIOS to display a warning on the screen that DDR speed was reduced due to mixed DIMM config + BOOLEAN DynamicMemoryBoostTrainingFailed; ///< TRUE if Dynamic Memory Boost failed to train and was force disabled on the last full training boot. FALSE otherwise. +} MEMORY_INFO_DATA_HOB; + +/** + Memory Platform Data Hob + + <b>Revision 1:</b> + - Initial version. + <b>Revision 2:</b> + - Added TsegBase, PrmrrSize, PrmrrBase, Gttbase, MmioSize, PciEBaseAddress fields +**/ +typedef struct { + UINT8 Revision; + UINT8 Reserved[3]; + UINT32 BootMode; + UINT32 TsegSize; + UINT32 TsegBase; + UINT32 PrmrrSize; + UINT64 PrmrrBase; + UINT32 GttBase; + UINT32 MmioSize; + UINT32 PciEBaseAddress; + PSMI_MEM_INFO PsmiInfo[MAX_TRACE_CACHE_TYPE]; + PSMI_MEM_INFO PsmiRegionInfo[MAX_TRACE_REGION]; + BOOLEAN MrcBasicMemoryTestPass; +} MEMORY_PLATFORM_DATA; + +typedef struct { + EFI_HOB_GUID_TYPE EfiHobGuidType; + MEMORY_PLATFORM_DATA Data; + UINT8 *Buffer; +} MEMORY_PLATFORM_DATA_HOB; + +#pragma pack (pop) + +#endif // _MEM_INFO_HOB_H_ |