aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--src/soc/intel/apollolake/chip.c6
-rw-r--r--src/soc/intel/apollolake/include/soc/fsp/FspmUpd.h47
-rw-r--r--src/soc/intel/apollolake/include/soc/fsp/FspsUpd.h83
3 files changed, 85 insertions, 51 deletions
diff --git a/src/soc/intel/apollolake/chip.c b/src/soc/intel/apollolake/chip.c
index 821570bfe8..044ef913b9 100644
--- a/src/soc/intel/apollolake/chip.c
+++ b/src/soc/intel/apollolake/chip.c
@@ -253,12 +253,6 @@ void platform_fsp_silicon_init_params_cb(struct FSPS_UPD *silupd)
if (cfg->emmc_rx_cmd_data_cntl2 != 0)
silconfig->EmmcRxCmdDataCntl2 = cfg->emmc_rx_cmd_data_cntl2;
- /* Our defaults may not match FSP defaults, so set them explicitly */
- silconfig->AcpiBase = ACPI_PMIO_BASE;
- /* First 4k in BAR0 is used for IPC, real registers start at 4k offset */
- silconfig->PmcBase = PMC_BAR0 + 0x1000;
- silconfig->P2sbBase = P2SB_BAR;
-
silconfig->IshEnable = cfg->integrated_sensor_hub_enable;
/* Disable setting of EISS bit in FSP. */
diff --git a/src/soc/intel/apollolake/include/soc/fsp/FspmUpd.h b/src/soc/intel/apollolake/include/soc/fsp/FspmUpd.h
index 5f5f367b45..3712fd7d01 100644
--- a/src/soc/intel/apollolake/include/soc/fsp/FspmUpd.h
+++ b/src/soc/intel/apollolake/include/soc/fsp/FspmUpd.h
@@ -36,6 +36,42 @@ are permitted provided that the following conditions are met:
#include "FspUpd.h"
#include <fsp/upd.h>
+#define MAX_CHANNELS_NUM 4
+#define MAX_DIMMS_NUM 1
+
+struct DIMM_INFO {
+ uint8_t DimmId;
+ uint32_t SizeInMb;
+ uint16_t MfgId;
+ /** Module part number for DRR3 is 18 bytes
+ but DRR4 is 20 bytes as per JEDEC Spec, so
+ reserving 20 bytes **/
+ uint8_t ModulePartNum[20];
+} __attribute__((packed));
+
+struct CHANNEL_INFO {
+ uint8_t ChannelId;
+ uint8_t DimmCount;
+ struct DIMM_INFO DimmInfo[MAX_DIMMS_NUM];
+} __attribute__((packed));
+
+struct FSP_SMBIOS_MEMORY_INFO {
+ uint8_t Revision;
+ uint8_t DataWidth;
+ /** As defined in SMBIOS 3.0 spec
+ Section 7.18.2 and Table 75
+ **/
+ uint16_t MemoryType;
+ uint16_t MemoryFrequencyInMHz;
+ /** As defined in SMBIOS 3.0 spec
+ Section 7.17.3 and Table 72
+ **/
+ uint8_t ErrorCorrectionType;
+ uint8_t ChannelCount;
+ struct CHANNEL_INFO ChannelInfo[MAX_CHANNELS_NUM];
+} __attribute__((packed));
+
+
/** Fsp M Configuration
**/
struct FSP_M_CONFIG {
@@ -528,9 +564,16 @@ struct FSP_M_CONFIG {
**/
void* MrcBootDataPtr;
-/** Offset 0x0135
+/** Offset 0x0135 - Skip CSE RBP to support zero sized IBB
+ Enable/Disable skip CSE RBP for bootloader which loads IBB without assistance of
+ CSE. 0x00:Disable(Default), 0x01:Enable.
+ $EN_DIS
+**/
+ uint8_t SkipCseRbp;
+
+/** Offset 0x0136
**/
- uint8_t ReservedFspmUpd[27];
+ uint8_t ReservedFspmUpd[26];
} __attribute__((packed));
/** Fsp M Test Configuration
diff --git a/src/soc/intel/apollolake/include/soc/fsp/FspsUpd.h b/src/soc/intel/apollolake/include/soc/fsp/FspsUpd.h
index d4ecd369cb..8dd824bbe3 100644
--- a/src/soc/intel/apollolake/include/soc/fsp/FspsUpd.h
+++ b/src/soc/intel/apollolake/include/soc/fsp/FspsUpd.h
@@ -587,10 +587,9 @@ struct FSP_S_CONFIG {
**/
uint8_t HpetFunctionNumber;
-/** Offset 0x00AF - Hpet Base Address
- Hpet Base Address. 0xFED00000(Default).
+/** Offset 0x00AF
**/
- uint32_t HpetBase;
+ uint32_t UnusedUpdSpace1;
/** Offset 0x00B3 - IoApic Valid BDF Value
Enable/Disable IoApic Valid BDF Value. 0:Disable(Default), 1:Enable.
@@ -635,7 +634,7 @@ struct FSP_S_CONFIG {
**/
uint8_t IshEnable;
-/** Offset 0x00BB - ISH Controller
+/** Offset 0x00BB - BIOS Interface Lock Down
Enable/Disable BIOS Interface Lock Down bit to prevent writes to the Backup Control
Register. 0:Disable, 1:Enable(Default).
$EN_DIS
@@ -663,7 +662,7 @@ struct FSP_S_CONFIG {
Enable/Disable LPSS IOSF Bridge PMCTL Register S0ix Bits. 0:Disable(Default), 1:Enable.
$EN_DIS
**/
- uint8_t S0ixEnable;
+ uint8_t LPSS_S0ixEnable;
/** Offset 0x00C0 - LPSS I2C Clock Gating Configuration
Enable/Disable LPSS I2C Clock Gating. 0:Disable, 1:Enable(Default).
@@ -770,8 +769,8 @@ struct FSP_S_CONFIG {
**/
uint8_t Spi2Enable;
-/** Offset 0x00DE - UART Debug Bass Address
- UART Debug Bass Address. 0x00000000(Default).
+/** Offset 0x00DE - UART Debug Base Address
+ UART Debug Base Address. 0x00000000(Default).
**/
uint32_t Uart2KernelDebugBaseAddress;
@@ -810,7 +809,7 @@ struct FSP_S_CONFIG {
**/
uint8_t PcieRootPortPeerMemoryWriteEnable;
-/** Offset 0x00E8 - PCIE SWSMI Nubmer
+/** Offset 0x00E8 - PCIE SWSMI Number
This member describes the SwSmi value for override PCIe ASPM table. 0xAA(Default).
**/
uint8_t PcieAspmSwSmiNumber;
@@ -932,7 +931,7 @@ struct FSP_S_CONFIG {
uint8_t PcieRpCompletionTimeout[6];
/** Offset 0x0173 - PTM Support
- Enable/Diable PTM Support. 0:Disable(Default), 1:Enable.
+ Enable/Disable PTM Support. 0:Disable(Default), 1:Enable.
**/
uint8_t PtmEnable[6];
@@ -957,7 +956,7 @@ struct FSP_S_CONFIG {
**/
uint8_t PcieRpLtrConfigLock[6];
-/** Offset 0x0191 - PME_B0_S5 Diable bit
+/** Offset 0x0191 - PME_B0_S5 Disable bit
PME_B0_S5_DIS bit in the General PM Configuration B (GEN_PMCON_B) register. 0:Disable(Default), 1:Enable.
$EN_DIS
**/
@@ -1029,8 +1028,8 @@ struct FSP_S_CONFIG {
uint8_t SataPortsHotPlug[2];
/** Offset 0x01A0 - Mechanical Presence Switch
- Controls reporting if this port has an Mechanical Presence Switch.\nNote:Requires
- hardware support. 0:Disable, 1:Enable(Default).
+ Controls reporting if this port has an Mechanical Presence Switch.\n
+ Note:Requires hardware support. 0:Disable, 1:Enable(Default).
**/
uint8_t SataPortsInterlockSw[2];
@@ -1075,20 +1074,9 @@ struct FSP_S_CONFIG {
**/
uint16_t SubSystemId;
-/** Offset 0x01B4 - PM Base Address
- PM Base Address. 0x400(Default).
+/** Offset 0x01B4
**/
- uint16_t AcpiBase;
-
-/** Offset 0x01B6 - PMC Base Address
- PMC Base Address. 0xD10010000(Default).
-**/
- uint32_t PmcBase;
-
-/** Offset 0x01BA - P2SB Base Address
- P2SB Base Address. 0xD0000000(Default).
-**/
- uint32_t P2sbBase;
+ uint8_t UnusedUpdSpace2[10];
/** Offset 0x01BE - CRIDSettings
PMC CRID setting. 0:Disable(Default), 1:CRID_1, 2:CRID_2, 3:CRID_3.
@@ -1150,7 +1138,7 @@ struct FSP_S_CONFIG {
/** Offset 0x01C8 - Start Frame Pulse Width
Start Frame Pulse Width Value. 0:ScSfpw4Clk(Default), 1: ScSfpw6Clk, 2:ScSfpw8Clk.
- $EN_DIS
+ 0:ScSfpw4Clk, 1:ScSfpw6Clk, 2:ScSfpw8Clk
**/
uint8_t StartFramePulse;
@@ -1166,10 +1154,9 @@ struct FSP_S_CONFIG {
**/
uint8_t ArpEnable;
-/** Offset 0x01CB - SMBus Base Address (IO space)
- SMBUS Base Address (IO space). 0xEFA0(Default).
+/** Offset 0x01CB
**/
- uint16_t SmbusIoBase;
+ uint16_t UnusedUpdSpace3;
/** Offset 0x01CD - SMBus Table Elements
The number of elements in the Reserved SMBus Address Table. 0x0080(Default).
@@ -1189,14 +1176,14 @@ struct FSP_S_CONFIG {
uint8_t DisableComplianceMode;
/** Offset 0x0250 - USB Per-Port Control
- Control each of the USB ports (0~3) enable/disable. 0:Disable(Default), 1:Enable.
+ Control each of the USB ports enable/disable. 0:Disable(Default), 1:Enable.
$EN_DIS
**/
uint8_t UsbPerPortCtl;
/** Offset 0x0251 - xHCI Mode
- Mode of operation of xHCI controller. 0:Disable, 1:Enable, 2:Auto(Default), 3:SmartAuto.
- $EN_DIS
+ Mode of operation of xHCI controller. 0:Disable, 1:Enable, 2:Auto(Default)
+ 0:Disable, 1:Enable, 2:Auto
**/
uint8_t Usb30Mode;
@@ -1224,7 +1211,7 @@ struct FSP_S_CONFIG {
/** Offset 0x026E - XDCI Support
Enable/Disable XDCI. 0:Disable, 1:PCI_Mode(Default), 2:ACPI_mode.
- $EN_DIS
+ 0:Disable, 1:PCI_Mode, 2:ACPI_mode
**/
uint8_t UsbOtg;
@@ -1293,8 +1280,10 @@ struct FSP_S_CONFIG {
uint16_t PcieRpLtrMaxSnoopLatency[6];
/** Offset 0x028A - Snoop Latency Override
- Snoop Latency Override for PCH PCIE. \nDisabled:Disable override.\nManual:Manually
- enter override values.\nAuto:Maintain default BIOS flow. 0:Disable, 1:Enable, 2:Auto(Default).
+ Snoop Latency Override for PCH PCIE. \n
+ Disabled:Disable override.\n
+ Manual:Manually enter override values.\n
+ Auto:Maintain default BIOS flow. 0:Disable, 1:Enable, 2:Auto(Default).
**/
uint8_t PcieRpSnoopLatencyOverrideMode[6];
@@ -1315,9 +1304,10 @@ struct FSP_S_CONFIG {
uint16_t PcieRpLtrMaxNonSnoopLatency[6];
/** Offset 0x02AE - Non Snoop Latency Override
- Non Snoop Latency Override for PCH PCIE. \nDisabled:Disable override.\nManual:Manually
- enter override values.\nAuto: Maintain default BIOS flow. 0:Disable, 1:Enable,
- 2:Auto(Default).
+ Non Snoop Latency Override for PCH PCIE. \n
+ Disabled:Disable override.\n
+ Manual:Manually enter override values.\n
+ Auto: Maintain default BIOS flow. 0:Disable, 1:Enable, 2:Auto(Default).
**/
uint8_t PcieRpNonSnoopLatencyOverrideMode[6];
@@ -1361,7 +1351,7 @@ struct FSP_S_CONFIG {
**/
uint8_t TcoTimerHaltLock;
-/** Offset 0x02D5 - Power Button Override Peroid
+/** Offset 0x02D5 - Power Button Override Period
specifies how long will PMC wait before initiating a global reset. 000b-4s(default),
001b-6s, 010b-8s, 011b-10s, 100b-12s, 101b-14s.)
0x0:4s, 0x1:6s, 0x2:8s, 0x3:10s, 0x4:12s, 0x5:14s
@@ -1369,7 +1359,7 @@ struct FSP_S_CONFIG {
uint8_t PwrBtnOverridePeriod;
/** Offset 0x02D6 - Power Button Native Mode Disable
- Diable power button native mode, when 1, this will result in the PMC logic constantly
+ Disable power button native mode, when 1, this will result in the PMC logic constantly
seeing the power button as de-asserted. 0 (default))
$EN_DIS
**/
@@ -1479,13 +1469,20 @@ struct FSP_S_CONFIG {
/** Offset 0x0326 - Os Selection Mode
Select OS mode. 0:Windows(default), 1:Android, 2:Win7
- $EN_DIS
+ 0:Windows, 1:Android, 2:Win7
**/
uint8_t OsSelection;
-/** Offset 0x0327
+/** Offset 0x0327 - Monitor Mwait Enable
+ Enable/Disable Monitor Mwait. For Windows* OS, this should be Enabled. For Linux
+ based OS, this should be Disabled. 0:Disable, 1:Enable(Default).
+ $EN_DIS
+**/
+ uint8_t MonitorMwaitEnable;
+
+/** Offset 0x0328
**/
- uint8_t ReservedFspsUpd[9];
+ uint8_t ReservedFspsUpd[8];
} __attribute__((packed));
/** Fsp S Test Configuration
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-03 02:41:43 +0000