diff options
| -rw-r--r-- | src/mainboard/google/skyrim/variants/markarth/overridetree.cb | 116 |
1 files changed, 115 insertions, 1 deletions
diff --git a/src/mainboard/google/skyrim/variants/markarth/overridetree.cb b/src/mainboard/google/skyrim/variants/markarth/overridetree.cb index 7a56f93759..f8e5268aea 100644 --- a/src/mainboard/google/skyrim/variants/markarth/overridetree.cb +++ b/src/mainboard/google/skyrim/variants/markarth/overridetree.cb @@ -1,5 +1,119 @@ # SPDX-License-Identifier: GPL-2.0-or-later chip soc/amd/mendocino - device domain 0 on end + + device domain 0 on + device ref gpp_bridge_1 on + # Required so the NVMe gets placed into D3 when entering S0i3. + chip drivers/pcie/rtd3/device + register "name" = ""NVME"" + device pci 00.0 on end + end + end # NVME + device ref gpp_bridge_2 on + # Required so the NVMe gets placed into D3 when entering S0i3. + chip drivers/pcie/rtd3/device + register "name" = ""NVME"" + device pci 00.0 on end + end + end # NVME + + device ref gpp_bridge_a on # Internal GPP Bridge 0 to Bus A + device ref xhci_1 on # XHCI1 controller + chip drivers/usb/acpi + device ref xhci_1_root_hub on # XHCI1 root hub + chip drivers/usb/acpi + device ref usb3_port3 on # USB 3.1 port3 + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(2, 2))" + device usb 3.1 on end + end + end # USB 3.1 port3 + end + chip drivers/usb/acpi + device ref usb2_port3 on # USB 2 port3 + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(2, 2))" + device usb 2.1 on end + end + end # USB 2 port3 + end + end # XHCI1 root hub + end + end # XHCI1 controller + end # Internal GPP Bridge 0 to Bus A + end # domain + + device ref i2c_0 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_40)" + register "wake" = "GEVENT_20" + register "detect" = "1" + device i2c 15 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""SYNA0000"" + register "generic.cid" = ""ACPI0C50"" + register "generic.desc" = ""Synaptics Touchpad"" + register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_40)" + register "generic.wake" = "GEVENT_20" + register "generic.detect" = "1" + register "hid_desc_reg_offset" = "0x20" + device i2c 2c on end + end + end # I2C0 + device ref i2c_1 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN9004"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_29)" + register "generic.detect" = "1" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_131)" + register "generic.enable_delay_ms" = "10" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_136)" + register "generic.reset_off_delay_ms" = "1" + register "generic.reset_delay_ms" = "10" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_76)" + register "generic.stop_delay_ms" = "180" + register "generic.stop_off_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + end # I2C1 + device ref i2c_2 on + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Realtek RT5682"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPIO_90)" + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + chip drivers/i2c/generic + register "hid" = ""10EC1019"" + register "desc" = ""Realtek SPK AMP R"" + register "uid" = "1" + device i2c 29 on end + end + chip drivers/i2c/generic + register "hid" = ""10EC1019"" + register "desc" = ""Realtek SPK AMP L"" + register "uid" = "2" + register "probed" = "1" + device i2c 2a on end + end + end # I2C2 + end # chip soc/amd/mendocino |