Since some people disapprove of white space cleanups mixed in regular commits

while others dislike them being extra commits, let's clean them up once and
for all for the existing code. If it's ugly, let it only be ugly once :-)

Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>



git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5507 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

1 files changed, 19 insertions, 19 deletions

diff --git a/src/southbridge/intel/i82801cx/i82801cx_lpc.c b/src/southbridge/intel/i82801cx/i82801cx_lpc.c
index 7523b03f80..97b2994abf 100644
--- a/src/southbridge/intel/i82801cx/i82801cx_lpc.c
+++ b/src/southbridge/intel/i82801cx/i82801cx_lpc.c
@@ -23,7 +23,7 @@
 #define MAINBOARD_POWER_ON  1
 
 
-static void i82801cx_enable_ioapic( struct device *dev) 
+static void i82801cx_enable_ioapic( struct device *dev)
 {
 	uint32_t dword;
     volatile uint32_t* ioapic_index = (volatile uint32_t*)0xfec00000;
@@ -36,12 +36,12 @@ static void i82801cx_enable_ioapic( struct device *dev)
     dword |= (1 << 2); /* DMA collection buf enable */
     pci_write_config32(dev, GEN_CNTL, dword);
     printk(BIOS_DEBUG, "ioapic southbridge enabled %x\n",dword);
-        
+
     // Must program the APIC's ID before using it
 
     *ioapic_index = 0;		// Select APIC ID register
     *ioapic_data = (2<<24);
-        
+
     // Hang if the ID didn't take (chip not present?)
     *ioapic_index = 0;
     dword = *ioapic_data;
@@ -65,11 +65,11 @@ static void i82801cx_enable_serial_irqs( struct device *dev)
 // Parameters:  	dev
 //					mask - identifies whether each channel should be used for PCI DMA
 //						   (bit = 0) or LPC DMA (bit = 1). The LSb controls channel 0.
-//						   Channel 4 is not used (reserved). 
+//						   Channel 4 is not used (reserved).
 // Return Value:	None
 // Description: 	Route all DMA channels to either PCI or LPC.
 //
-static void i82801cx_lpc_route_dma( struct device *dev, uint8_t mask) 
+static void i82801cx_lpc_route_dma( struct device *dev, uint8_t mask)
 {
     uint16_t dmaConfig;
     int channelIndex;
@@ -105,13 +105,13 @@ static void i82801cx_rtc_init(struct device *dev)
 		pmcon3 |= SLEEP_AFTER_POWER_FAIL;
 	}
 	pci_write_config8(dev, GEN_PMCON_3, pmcon3);
-	printk(BIOS_INFO, "set power %s after power fail\n", 
+	printk(BIOS_INFO, "set power %s after power fail\n",
 				 pwr_on ? "on" : "off");
 
     // See if the Safe Mode jumper is set
     dword = pci_read_config32(dev, GEN_STS);
     rtc_failed |= dword & (1 << 2);
-        
+
     rtc_init(rtc_failed);
 }
 
@@ -120,28 +120,28 @@ static void i82801cx_1f0_misc(struct device *dev)
 {
 	// Prevent LPC disabling, enable parity errors, and SERR# (System Error)
     pci_write_config16(dev, PCI_COMMAND, 0x014f);
-        
+
     // Set ACPI base address to 0x1100 (I/O space)
     pci_write_config32(dev, PMBASE, 0x00001101);
-        
+
     // Enable ACPI I/O and power management
     pci_write_config8(dev, ACPI_CNTL, 0x10);
-        
+
     // Set GPIO base address to 0x1180 (I/O space)
     pci_write_config32(dev, GPIO_BASE, 0x00001181);
-        
+
     // Enable GPIO
     pci_write_config8(dev, GPIO_CNTL, 0x10);
-        
+
     // Route PIRQA to IRQ11, PIRQB to IRQ3, PIRQC to IRQ5, PIRQD to IRQ10
     pci_write_config32(dev, PIRQA_ROUT, 0x0A05030B);
-        
+
     // Route PIRQE to IRQ7. Leave PIRQF - PIRQH unrouted.
     pci_write_config8(dev, PIRQE_ROUT, 0x07);
-        
+
     // Enable access to the upper 128 byte bank of CMOS RAM
     pci_write_config8(dev, RTC_CONF, 0x04);
-        
+
     // Decode 0x3F8-0x3FF (COM1) for COMA port,
 	//		  0x2F8-0x2FF (COM2) for COMB
     pci_write_config8(dev, COM_DEC, 0x10);
@@ -149,7 +149,7 @@ static void i82801cx_1f0_misc(struct device *dev)
 	// LPT decode defaults to 0x378-0x37F and 0x778-0x77F
 	// Floppy decode defaults to 0x3F0-0x3F5, 0x3F7
 
-    // Enable COMA, COMB, LPT, floppy; 
+    // Enable COMA, COMB, LPT, floppy;
 	// disable microcontroller, Super I/O, sound, gameport
     pci_write_config16(dev, LPC_EN, 0x000F);
 }
@@ -164,7 +164,7 @@ static void lpc_init(struct device *dev)
 	i82801cx_enable_ioapic(dev);
 
 	i82801cx_enable_serial_irqs(dev);
-	
+
 	/* power after power fail */
 	        /* FIXME this doesn't work! */
         /* Which state do we want to goto after g3 (power restored)?
@@ -187,11 +187,11 @@ static void lpc_init(struct device *dev)
     byte = inb(0x70);
     nmi_option = NMI_OFF;
     get_option(&nmi_option, "nmi");
-    if (nmi_option) {			
+    if (nmi_option) {
         byte &= ~(1 << 7); /* set NMI */
         outb(byte, 0x70);
     }
-	
+
 	/* Initialize the real time clock */
 	i82801cx_rtc_init(dev);