Add supermicro h8dmr fam10 target. This is largely a mashup of the tyan s2912

fam10 and h8dmr k8 targets.

Many, many thanks to Marc, Myles, Patrick and Stepan for all their help with
this, and to Arne for doing the s2912 fam10 port.

Build and boot tested. Abuild tested.

There are a number of outstanding issues and caveats - see src/mainboard/supermicro/h8dmr_fam10/README.

Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Peter Stuge <peter@stuge.se>




git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4693 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

1 files changed, 371 insertions, 0 deletions

diff --git a/src/mainboard/supermicro/h8dmr_fam10/Options.lb b/src/mainboard/supermicro/h8dmr_fam10/Options.lb
new file mode 100644
index 0000000000..7fc17b7e52
--- /dev/null
+++ b/src/mainboard/supermicro/h8dmr_fam10/Options.lb
@@ -0,0 +1,371 @@
+## 
+## This file is part of the coreboot project.
+## 
+## Copyright (C) 2007 AMD
+## Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+## 
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+## 
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+## 
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+## 
+
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CBFS
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_MAX_CPUS
+uses CONFIG_MAX_PHYSICAL_CPUS
+uses CONFIG_LOGICAL_CPUS
+uses CONFIG_IOAPIC
+uses CONFIG_SMP
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
+uses CONFIG_ROM_PAYLOAD
+uses CONFIG_ROM_PAYLOAD_START
+uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
+uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses COREBOOT_EXTRA_VERSION
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_CONSOLE_SERIAL8250
+uses CONFIG_HAVE_INIT_TIMER
+uses CONFIG_GDB_STUB
+uses CONFIG_CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_CONSOLE_VGA
+uses CONFIG_PCI_ROM_RUN
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_USE_INIT
+
+uses CONFIG_SERIAL_CPU_INIT
+
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
+
+uses CONFIG_PCI_64BIT_PREF_MEM
+
+uses CONFIG_LB_MEM_TOPK
+
+uses CONFIG_UNCOMPRESSED
+
+uses CONFIG_PCI_BUS_SEGN_BITS
+
+uses CONFIG_AP_CODE_IN_CAR
+
+uses CONFIG_MEM_TRAIN_SEQ
+
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
+
+uses CONFIG_AMDMCT
+
+uses CONFIG_USE_PRINTK_IN_CAR
+uses CONFIG_CAR_FAM10
+uses CONFIG_AMD_UCODE_PATCH_FILE
+
+###
+### Build options
+###
+
+##
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+##
+default CONFIG_ROM_SIZE=1024*1024
+
+##
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the ROM part of the fallback image will use
+default CONFIG_FALLBACK_SIZE=CONFIG_ROM_IMAGE_SIZE
+default CONFIG_FAILOVER_SIZE=0x02000
+
+#more 1M for pgtbl
+default CONFIG_LB_MEM_TOPK=16384
+
+##
+## Build code for the fallback boot
+##
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
+
+##
+## Build code to reset the motherboard from coreboot
+##
+default CONFIG_HAVE_HARD_RESET=1
+
+##
+## Build code to export a programmable irq routing table
+##
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+default CONFIG_HAVE_MP_TABLE=1
+
+## ACPI tables will be included
+default CONFIG_HAVE_ACPI_TABLES=0
+
+##
+## Build code to export a CMOS option table
+##
+default CONFIG_HAVE_OPTION_TABLE=1
+
+##
+## Move the default coreboot cmos range off of AMD RTC registers
+##
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+##
+default CONFIG_SMP=1
+default CONFIG_MAX_PHYSICAL_CPUS=2
+default CONFIG_MAX_CPUS=4 * CONFIG_MAX_PHYSICAL_CPUS
+default CONFIG_LOGICAL_CPUS=1
+
+default CONFIG_SERIAL_CPU_INIT=0
+
+default CONFIG_ENABLE_APIC_EXT_ID=1
+default CONFIG_APIC_ID_OFFSET=0x00
+default CONFIG_LIFT_BSP_APIC_ID=1
+
+#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead. 
+#2G
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
+#1G
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
+#512M
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
+
+#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
+
+#VGA Console
+default CONFIG_CONSOLE_VGA=1
+default CONFIG_PCI_ROM_RUN=1
+
+#HT Unit ID offset, default is 1, the typical one, 0 mean only one HT device
+default CONFIG_HT_CHAIN_UNITID_BASE=1
+
+#real SB Unit ID, default is 0x20, mean dont touch it at last
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
+
+#make the SB HT chain on bus 0, default is not (0)
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
+
+#only offset for SB chain?, default is yes(1)
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+
+#allow capable device use that above 4G
+#default CONFIG_PCI_64BIT_PREF_MEM=1
+
+##
+## enable CACHE_AS_RAM specifics
+##
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc4000
+default CONFIG_DCACHE_RAM_SIZE=0x0c000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x04000
+default CONFIG_USE_INIT=0
+
+default CONFIG_MEM_TRAIN_SEQ=2
+default CONFIG_WAIT_BEFORE_CPUS_INIT=0
+default CONFIG_AMDMCT = 1
+
+##
+## Build code to setup a generic IOAPIC
+##
+default CONFIG_IOAPIC=1
+
+##
+## Clean up the motherboard id strings
+##
+default CONFIG_MAINBOARD_PART_NUMBER="h8dmr (Fam10)"
+default CONFIG_MAINBOARD_VENDOR="Supermicro"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15d9
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1511
+
+##
+## Set microcode patch file name
+##
+##      Barcelona rev Ax:  "mc_patch_01000020.h"
+##      Barcelona rev B0, B1, BA: "mc_patch_01000084.h"
+##      Barcelona rev B2, B3: "mc_patch_01000083.h"
+##			Shanghai rev RB-C2: "mc_patch_01000086.h"
+##			Shanghai rev DA-C2: "mc_patch_0100009f.h"
+##
+#default CONFIG_AMD_UCODE_PATCH_FILE="mc_patch_01000086.h"
+default CONFIG_AMD_UCODE_PATCH_FILE="mc_patch_0100009f.h"
+
+###
+### coreboot layout values
+###
+
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 0x1e000
+
+##
+## Use a 32K stack
+##
+default CONFIG_STACK_SIZE=0x8000
+
+##
+## Use a 48K heap
+##
+default CONFIG_HEAP_SIZE=0xc0000
+
+##
+## Only use the option table in a normal image
+##
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
+
+##
+## Coreboot C code runs at this location in RAM
+##
+default CONFIG_RAMBASE=0x00200000
+
+##
+## Load the payload from the ROM
+##
+default CONFIG_ROM_PAYLOAD = 1
+
+#default CONFIG_COMPRESSED_PAYLOAD = 1
+
+# CBFS will take care of payload compression
+default CONFIG_UNCOMPRESSED = 1
+
+###
+### Defaults of options that you may want to override in the target config file
+### 
+
+##
+## The default compiler
+##
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## Disable the gdb stub by default
+## 
+default CONFIG_GDB_STUB=0
+
+##
+## The Serial Console
+##
+default CONFIG_USE_PRINTK_IN_CAR=1
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
+
+# Select the serial console base port
+default CONFIG_TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default CONFIG_TTYS0_LCS=0x3
+
+##
+### Select the coreboot loglevel
+##
+## EMERG      1   system is unusable               
+## ALERT      2   action must be taken immediately 
+## CRIT       3   critical conditions              
+## ERR        4   error conditions                 
+## WARNING    5   warning conditions               
+## NOTICE     6   normal but significant condition 
+## INFO       7   informational                    
+## DEBUG      8   debug-level messages             
+## SPEW       9   Way too many details             
+
+## Request this level of debugging output
+default  CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+default  CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
+
+##
+## Select power on after power fail setting
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+
+default CONFIG_USE_FAILOVER_IMAGE=0
+default CONFIG_USE_FALLBACK_IMAGE=0
+default CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
+
+#
+# CBFS
+#
+#
+default CONFIG_CBFS=1
+
+### End Options.lb
+end