sandy/ivy/nehalem: Remerge interrupt handling

On those chipsets the pins are just a legacy concept. Real interrupts are
messages on corresponding busses or some internal logic of chipset.
Hence interrupt routing isn't anymore board-specific (dependent on layout) but
depends only on configuration.
Rather than attempting to sync real config, ACPI and legacy descriptors, just
use the same interrupt routing per chipset covering all possible devices.

The only part which remains board-specific are LPC and PCI interrupts.

Interrupt balancing may suffer from such merge but:
a) Doesn't seem to be the case of this map on current systems
b) Almost all OS use MSI nowadays bypassing this stuff completely
c) If we want a good balancing we need to take into account that e.g.
   wlan card may be placed in a different slot and so would require complicated
   balancing on runtime. It's difficult to maintain with almost no benefit.

Change-Id: I9f63d1d338c5587ebac7a52093e5b924f6e5ca2d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7130
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>

1 files changed, 0 insertions, 42 deletions

diff --git a/src/mainboard/lenovo/t520/romstage.c b/src/mainboard/lenovo/t520/romstage.c
index 83be0c7f86..f7866a86ad 100644
--- a/src/mainboard/lenovo/t520/romstage.c
+++ b/src/mainboard/lenovo/t520/romstage.c
@@ -60,48 +60,6 @@ void pch_enable_lpc(void)
 
 void rcba_config(void)
 {
-	/*
-	 *             GFX    INTA -> PIRQA (MSI)
-	 * D28IP_P2IP  WLAN   INTA -> PIRQB
-	 * D28IP_P4IP  EXC    INTB -> PIRQF
-	 * D28IP_P5IP  SDCARD INTC -> PIRQD
-	 * D29IP_E1P   EHCI1  INTA -> PIRQD
-	 * D26IP_E2P   EHCI2  INTA -> PIRQF
-	 * D31IP_SIP   SATA   INTA -> PIRQB (MSI)
-	 * D31IP_SMIP  SMBUS  INTB -> PIRQH
-	 * D31IP_TTIP  THRT   INTC -> PIRQA
-	 * D27IP_ZIP   HDA    INTA -> PIRQA (MSI)
-	 *
-	 * Trackpad interrupt is edge triggered and cannot be shared.
-	 * TRACKPAD                -> PIRQG
-
-	 */
-
-	/* Device interrupt pin register (board specific) */
-	RCBA32(D31IP) = (INTC << D31IP_TTIP) | (NOINT << D31IP_SIP2) |
-			(INTB << D31IP_SMIP) | (INTA << D31IP_SIP);
-	RCBA32(D29IP) = (INTA << D29IP_E1P);
-	RCBA32(D28IP) = (INTA << D28IP_P2IP) | (INTB << D28IP_P4IP) |
-			(INTC << D28IP_P5IP);
-	RCBA32(D27IP) = (INTA << D27IP_ZIP);
-	RCBA32(D26IP) = (INTA << D26IP_E2P);
-	RCBA32(D25IP) = (NOINT << D25IP_LIP);
-	RCBA32(D22IP) = (NOINT << D22IP_MEI1IP);
-
-	/* Device interrupt route registers */
-	DIR_ROUTE(D31IR, PIRQB, PIRQH, PIRQA, PIRQC);
-	DIR_ROUTE(D29IR, PIRQD, PIRQE, PIRQF, PIRQG);
-	DIR_ROUTE(D28IR, PIRQB, PIRQF, PIRQD, PIRQE);
-	DIR_ROUTE(D27IR, PIRQA, PIRQH, PIRQA, PIRQB);
-	DIR_ROUTE(D26IR, PIRQF, PIRQE, PIRQG, PIRQH);
-	DIR_ROUTE(D25IR, PIRQA, PIRQB, PIRQC, PIRQD);
-	DIR_ROUTE(D22IR, PIRQA, PIRQB, PIRQC, PIRQD);
-
-	/* Enable IOAPIC (generic) */
-	RCBA16(OIC) = 0x0100;
-	/* PCH BWG says to read back the IOAPIC enable register */
-	(void) RCBA16(OIC);
-
 	/* Disable unused devices (board specific) */
 	RCBA32(FD) = 0x1ee51fe3;
 	RCBA32(BUC) = 0;