mb/intel/ehlcrb: Add initial mainboard code

This is a initial mainboard code cloned entirely from jasperlake_rvp
aimed to serve as base for further mainboard check-ins.

This patch is based on TGL_upstream series patches:
https://review.coreboot.org/c/coreboot/+/37868

List of changes on top off initial jasperlake_rvp clone:
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Replace "jslrvp" with "ehlcrb"
4. Remove unwanted SPD file, add empty SPD as placeholder
6. Empty romstage_fsp_params.c, to fill it later with SOC specific
   config
7. Empty GPIO configurations, to be filled as per board
8. Empty memory.c configurations, to be filled as per board
9. Add board support namely BOARD_INTEL_ELKHARTLAKE_CRB
10. Replace jslrvp variant with ehlcrb variant

Changes to follow on top of this:
 1. Add correct memory parameters, add SPDs
 2. Clean up devicetree as per tigerlake SOC
 3. Add GPIO support
 4. Update ehl fmd file to replace 32MB chromeos.fmd

Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I2cbe9f12468318680b148739edec5222582e42a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>

4 files changed, 362 insertions, 0 deletions

diff --git a/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/Makefile.inc b/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/Makefile.inc
new file mode 100644
index 0000000000..641e814351
--- /dev/null
+++ b/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/Makefile.inc
@@ -0,0 +1,5 @@
+## SPDX-License-Identifier: GPL-2.0-only
+
+bootblock-y += gpio.c
+romstage-y += memory.c
+ramstage-y += gpio.c
diff --git a/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/devicetree.cb b/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/devicetree.cb
new file mode 100644
index 0000000000..af0c7530f7
--- /dev/null
+++ b/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/devicetree.cb
@@ -0,0 +1,304 @@
+chip soc/intel/elkhartlake
+
+	device cpu_cluster 0 on
+		device lapic 0 on end
+	end
+
+	device domain 0 on
+		device pci 00.0 on  end # Host Bridge
+		device pci 02.0 on  end # Integrated Graphics Device
+		device pci 04.0 on
+			chip drivers/intel/dptf
+				register "policies.passive[0]" = "DPTF_PASSIVE(CPU, CPU, 95, 1000)"
+				register "policies.critical[0]" = "DPTF_CRITICAL(CPU, 119, SHUTDOWN)"
+
+				register "controls.power_limits.pl1" = "{
+					.min_power = 3000,
+					.max_power = 6000,
+					.time_window_min = 1 * MSECS_PER_SEC,
+					.time_window_max = 1 * MSECS_PER_SEC,
+					.granularity = 200,}"
+				register "controls.power_limits.pl2" = "{
+					.min_power = 20000,
+					.max_power = 20000,
+					.time_window_min = 1 * MSECS_PER_SEC,
+					.time_window_max = 1 * MSECS_PER_SEC,
+					.granularity = 1000,}"
+				device generic 0 on end
+			end
+		end # SA Thermal device
+
+		device pci 05.0 on
+			chip drivers/intel/mipi_camera
+				register "acpi_uid" = "0x50000"
+				register "acpi_name" = ""IPU0""
+				register "device_type" = "INTEL_ACPI_CAMERA_CIO2"
+
+				register "cio2_num_ports" = "2"
+				register "cio2_lanes_used" = "{2,2}"
+				register "cio2_lane_endpoint[0]" = ""^I2C4.CAM0""
+				register "cio2_lane_endpoint[1]" = ""^I2C5.CAM1""
+				register "cio2_prt[0]" = "0"
+				register "cio2_prt[1]" = "2"
+				device generic 0 on end
+			end
+		end
+		device pci 12.0 off end # Thermal Subsystem
+		device pci 12.5 off end # UFS SCS
+		device pci 12.6 off end # GSPI #2
+		device pci 14.0 on
+			chip drivers/usb/acpi
+				register "desc" = ""Root Hub""
+				register "type" = "UPC_TYPE_HUB"
+				device usb 0.0 on
+					chip drivers/usb/acpi
+						register "desc" = ""USB3/2 Type-A Left Lower""
+						register "type" = "UPC_TYPE_A"
+						device usb 2.0 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""WWAN""
+						register "type" = "UPC_TYPE_INTERNAL"
+						device usb 2.1 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""Bluetooth""
+						register "type" = "UPC_TYPE_INTERNAL"
+						device usb 2.2 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""USB C Connector 1""
+						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+						device usb 2.3 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""USB C Connector 2""
+						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+						device usb 2.4 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""USB C Connector 3""
+						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+						device usb 2.5 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""USB C Connector 4""
+						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+						device usb 2.6 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""USB3/2 Type-A Left Upper""
+						register "type" = "UPC_TYPE_A"
+						device usb 2.7 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""USB3/2 Type-A Left Lower""
+						register "type" = "UPC_TYPE_A"
+						device usb 3.0 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""USB3/2 Type-A Left Upper""
+						register "type" = "UPC_TYPE_A"
+						device usb 3.1 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""WLAN""
+						register "type" = "UPC_TYPE_INTERNAL"
+						device usb 3.2 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""USB3 Port Unused1""
+						register "type" = "UPC_TYPE_INTERNAL"
+						device usb 3.3 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""USB3 Port Unused2""
+						register "type" = "UPC_TYPE_INTERNAL"
+						device usb 3.4 on end
+					end
+					chip drivers/usb/acpi
+						register "desc" = ""USB3 Port Unused3""
+						register "type" = "UPC_TYPE_INTERNAL"
+						device usb 3.5 on end
+					end
+				end
+			end
+		end # USB xHCI
+		device pci 14.1 off end # USB xDCI (OTG)
+		device pci 14.2 off end # PMC SRAM
+		device pci 14.3 on
+			chip drivers/wifi/generic
+				register "wake" = "GPE0_PME_B0"
+				device generic 0 on end
+			end
+		end # CNVi wifi
+		device pci 14.5 on  end # SDCard
+		device pci 15.0 on
+			chip drivers/i2c/max98373
+				register "vmon_slot_no" = "4"
+				register "imon_slot_no" = "5"
+				register "uid" = "0"
+				register "desc" = ""RIGHT SPEAKER AMP""
+				register "name" = ""MAXR""
+				device i2c 31 on end
+			end
+			chip drivers/i2c/max98373
+				register "vmon_slot_no" = "6"
+				register "imon_slot_no" = "7"
+				register "uid" = "1"
+				register "desc" = ""LEFT SPEAKER AMP""
+				register "name" = ""MAXL""
+				device i2c 32 on end
+			end
+			chip drivers/i2c/da7219
+				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H16_IRQ)"
+				register "btn_cfg" = "50"
+				register "mic_det_thr" = "500"
+				register "jack_ins_deb" = "20"
+				register "jack_det_rate" = ""32ms_64ms""
+				register "jack_rem_deb" = "1"
+				register "a_d_btn_thr" = "0xa"
+				register "d_b_btn_thr" = "0x16"
+				register "b_c_btn_thr" = "0x21"
+				register "c_mic_btn_thr" = "0x3e"
+				register "btn_avg" = "4"
+				register "adc_1bit_rpt" = "1"
+				register "micbias_lvl" = "2600"
+				register "mic_amp_in_sel" = ""diff""
+				device i2c 1a on end
+			end
+		end # I2C #0 Audio
+		device pci 15.1 off end # I2C #1
+		device pci 15.2 off end # I2C #2
+		device pci 15.3 off end # I2C #3
+		device pci 16.0 on  end # Management Engine Interface 1
+		device pci 16.1 off end # Management Engine Interface 2
+		device pci 16.2 off end # Management Engine IDE-R
+		device pci 16.3 off end # Management Engine KT Redirection
+		device pci 16.4 off end # Management Engine Interface 3
+		device pci 16.5 off end # Management Engine Interface 4
+		device pci 17.0 off end # SATA
+		device pci 19.0 on # I2C #4 Cam 0
+			chip drivers/intel/mipi_camera
+				register "acpi_hid" = ""OVTI2740""
+				register "acpi_uid" = "0"
+				register "acpi_name" = ""CAM0""
+				register "chip_name" = ""Ov 2740 Camera""
+				register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"
+				register "has_power_resource" = "1"
+
+				register "ssdb.lanes_used" = "2"
+				register "num_freq_entries" = "1"
+				register "link_freq[0]" = "360000000"
+				register "remote_name" = ""IPU0""
+
+				#Controls
+				register "clk_panel.clks[0].clknum" = "0" #IMGCLKOUT_3
+				register "clk_panel.clks[0].freq" = "1" #19.2 Mhz
+
+				register "gpio_panel.gpio[0].gpio_num" = "GPP_D5" #reset
+				register "gpio_panel.gpio[1].gpio_num" = "GPP_B14" #power
+
+				#_ON
+				register "on_seq.ops_cnt" = "4"
+				register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)"
+				register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)"
+				register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 5)"
+				register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 5)"
+
+				#_OFF
+				register "off_seq.ops_cnt" = "3"
+				register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
+				register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"
+				register "off_seq.ops[2]" = "SEQ_OPS_CLK_DISABLE(0, 0)"
+
+				device i2c 10 on end
+			end
+		end
+		device pci 19.1 on # I2C #5 Cam 1 and VCM
+			chip drivers/intel/mipi_camera
+				register "acpi_hid" = ""OVTI5675""
+				register "acpi_uid" = "0"
+				register "acpi_name" = ""CAM1""
+				register "chip_name" = ""Ov 5675 Camera""
+				register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"
+
+				register "ssdb.lanes_used" = "2"
+				register "ssdb.link_used" = "1"
+				register "ssdb.vcm_type" = "0x0C"
+				register "vcm_name" = ""VCM0""
+				register "num_freq_entries" = "1"
+				register "link_freq[0]" = "DEFAULT_LINK_FREQ"
+				register "remote_name" = ""IPU0""
+
+				register "has_power_resource" = "1"
+				#Controls
+				register "clk_panel.clks[0].clknum" = "1" #IMGCLKOUT_3
+				register "clk_panel.clks[0].freq" = "1" #19.2 Mhz
+
+				register "gpio_panel.gpio[0].gpio_num" = "GPP_D4" #power_enable
+				register "gpio_panel.gpio[1].gpio_num" = "GPP_C19" #reset
+
+				#_ON
+				register "on_seq.ops_cnt" = "4"
+				register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)"
+				register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)"
+				register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 5)"
+				register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 5)"
+
+				#_OFF
+				register "off_seq.ops_cnt" = "3"
+				register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
+				register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"
+				register "off_seq.ops[2]" = "SEQ_OPS_CLK_DISABLE(0, 0)"
+
+				device i2c 36 on end
+			end
+			chip drivers/intel/mipi_camera
+				register "acpi_hid" = "ACPI_DT_NAMESPACE_HID"
+				register "acpi_uid" = "3"
+				register "acpi_name" = ""VCM0""
+				register "chip_name" = ""DW AF DAC""
+				register "device_type" = "INTEL_ACPI_CAMERA_VCM"
+
+				register "pr0" = ""\\_SB.PCI0.I2C5.CAM1.PRIC""
+				register "vcm_compat" = ""dongwoon,dw9714""
+
+				register "ssdb.lanes_used" = "2"
+				register "num_freq_entries" = "1"
+				register "link_freq[0]" = "DEFAULT_LINK_FREQ"
+				register "remote_name" = ""IPU0""
+				device i2c 0C on end
+			end
+		end
+
+		device pci 19.2 on  end # UART #2
+		device pci 1a.0 on  end # eMMC
+		device pci 1c.0 off end # PCI Express Port 1
+		device pci 1c.1 on  end # PCI Express Port 2 - WLAN
+		device pci 1c.2 off end # PCI Express Port 3
+		device pci 1c.3 off end # PCI Express Port 4
+		device pci 1c.4 on  end # PCI Express Port 5 - NVMe
+		device pci 1c.5 off end # PCI Express Port 6
+		device pci 1c.6 off end # PCI Express Port 7
+		device pci 1c.7 off end # PCI Express Port 8
+		device pci 1e.0 on  end # UART #0
+		device pci 1e.1 off end # UART #1
+		device pci 1e.2 off end # GSPI #0
+		device pci 1e.3 on
+			chip drivers/spi/acpi
+				register "hid" = "ACPI_DT_NAMESPACE_HID"
+				register "compat_string" = ""google,cr50""
+				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_H13_IRQ)"
+				device spi 0 on end
+			end
+		end # GSPI #1
+		device pci 1f.0 on  end # eSPI Interface
+		device pci 1f.1 on  end # P2SB
+		device pci 1f.2 hidden end # Power Management Controller
+		device pci 1f.3 on  end # Intel HDA
+		device pci 1f.4 on  end # SMBus
+		device pci 1f.5 on  end # PCH SPI
+		device pci 1f.6 off end # GbE
+	end
+end
diff --git a/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/gpio.c b/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/gpio.c
new file mode 100644
index 0000000000..f01202b498
--- /dev/null
+++ b/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/gpio.c
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#include <baseboard/gpio.h>
+#include <baseboard/variants.h>
+#include <commonlib/helpers.h>
+
+/* Pad configuration in ramstage*/
+static const struct pad_config gpio_table[] = {
+	/* ToDo: Fill gpio configurations */
+};
+
+/* Early pad configuration in bootblock */
+static const struct pad_config early_gpio_table[] = {
+	/* ToDo: Fill early gpio configurations */
+};
+
+const struct pad_config *variant_gpio_table(size_t *num)
+{
+	*num = ARRAY_SIZE(gpio_table);
+	return gpio_table;
+}
+
+const struct pad_config *variant_early_gpio_table(size_t *num)
+{
+	*num = ARRAY_SIZE(early_gpio_table);
+	return early_gpio_table;
+}
+
+static const struct cros_gpio cros_gpios[] = {
+	CROS_GPIO_REC_AL(CROS_GPIO_VIRTUAL, CROS_GPIO_COMM0_NAME),
+};
+
+const struct cros_gpio *variant_cros_gpios(size_t *num)
+{
+	*num = ARRAY_SIZE(cros_gpios);
+	return cros_gpios;
+}
diff --git a/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/memory.c b/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/memory.c
new file mode 100644
index 0000000000..e764fdc7f3
--- /dev/null
+++ b/src/mainboard/intel/elkhartlake_crb/variants/ehlcrb/memory.c
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#include <baseboard/variants.h>
+#include <baseboard/gpio.h>
+#include <gpio.h>
+#include <soc/meminit.h>
+#include <soc/romstage.h>
+
+/* ToDo : Fill EHL related memory configs */
+
+const struct mb_cfg *variant_memcfg_config(uint8_t board_id)
+{
+	/* ToDo : Fill EHL related memory configs */
+
+	die("unsupported board id : 0x%x\n", board_id);
+}