stoneyridge GPIO: Create and use PAD_INT for interrupt pins

The default interrupt control for GPIO pins within stoneyridge is for
edge triggered, high. However, sometimes these need to change, or maybe
the interrupt needs to be reported or delivered. This was the case of
platform grunt, where the interrupt related bits were being changed
afterwards. Ideally all the bits should be programmed through the same
procedure. Create several PAD_INT definitions (for general configuration,
for trigger configuration and for interrupt type configuration) and change
function sb_program_gpios() to accept the output from PAD_INT_XX and
program all the necessary bits while keeping compatibility with other
PAD_XX definitions.

BUG=b:72875858
TEST=Add code to report GPIO and interrupt configuration, build grunt and
record a baseline. Add new code, rebuild grunt and record a test output.
Compare baseline against test, there should be no change in GPIO or
interrupt programming.
Remove code that reports GPIO/interrupt configuration.

Change-Id: I3457543bdf64ec757fd82df53c83fdc1d03c1f22
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>

2 files changed, 24 insertions, 96 deletions

diff --git a/src/mainboard/google/kahlee/variants/baseboard/gpio.c b/src/mainboard/google/kahlee/variants/baseboard/gpio.c
index ff6141e525..c7bd6a5be9 100644
--- a/src/mainboard/google/kahlee/variants/baseboard/gpio.c
+++ b/src/mainboard/google/kahlee/variants/baseboard/gpio.c
@@ -32,16 +32,17 @@ static const struct soc_amd_gpio gpio_set_stage_reset_old[] = {
 	PAD_GPO(GPIO_4, HIGH),
 
 	/* GPIO_6 - APU_RST_L / EC_SMI_ODL, SMI */
-	PAD_GPI(GPIO_6, PULL_UP),
+	PAD_SMI(GPIO_6, PULL_UP, LEVEL_LOW),
 
 	/* GPIO_9 - H1_PCH_INT_ODL, SCI */
-	PAD_GPI(GPIO_9, PULL_UP),
+	PAD_INT(GPIO_9, PULL_UP, EDGE_LOW, STATUS),
+	PAD_SCI(GPIO_9, PULL_UP, EDGE_LOW),
 
 	/* GPIO_15 - EC_IN_RW_OD */
 	PAD_GPI(GPIO_15, PULL_UP),
 
 	/* GPIO_22 - EC_SCI_ODL, SCI */
-	PAD_GPI(GPIO_22, PULL_UP),
+	PAD_SCI(GPIO_22, PULL_UP, EDGE_LOW),
 
 	/* GPIO_26 - APU_PCIE_RST_L */
 	PAD_NF(GPIO_26, PCIE_RST_L, PULL_NONE),
@@ -85,16 +86,17 @@ static const struct soc_amd_gpio gpio_set_stage_reset[] = {
 	PAD_GPO(GPIO_4, HIGH),
 
 	/* GPIO_6 - APU_RST_L / EC_SMI_ODL, SMI */
-	PAD_GPI(GPIO_6, PULL_UP),
+	PAD_SMI(GPIO_6, PULL_UP, LEVEL_LOW),
 
 	/* GPIO_9 - H1_PCH_INT_ODL, SCI */
-	PAD_GPI(GPIO_9, PULL_UP),
+	PAD_INT(GPIO_9, PULL_UP, EDGE_LOW, STATUS),
+	PAD_SCI(GPIO_9, PULL_UP, EDGE_LOW),
 
 	/* GPIO_15 - EC_IN_RW_OD */
 	PAD_GPI(GPIO_15, PULL_UP),
 
 	/* GPIO_22 - EC_SCI_ODL, SCI */
-	PAD_GPI(GPIO_22, PULL_UP),
+	PAD_SCI(GPIO_22, PULL_UP, EDGE_LOW),
 
 	/* GPIO_24 - EC_PCH_WAKE_L */
 	PAD_GPI(GPIO_24, PULL_UP),
@@ -150,7 +152,7 @@ static const struct soc_amd_gpio gpio_set_stage_ram_old[] = {
 	PAD_GPI(GPIO_3, PULL_UP),
 
 	/* GPIO_5 - PCH_TRACKPAD_INT_3V3_ODL, SCI */
-	PAD_GPI(GPIO_5, PULL_UP),
+	PAD_SCI(GPIO_5, PULL_UP, EDGE_LOW),
 
 	/* GPIO_7 - APU_PWROK_OD (currently not used) */
 	PAD_GPI(GPIO_7, PULL_UP),
@@ -162,7 +164,7 @@ static const struct soc_amd_gpio gpio_set_stage_ram_old[] = {
 	PAD_NF(GPIO_10, S0A3_GPIO, PULL_UP),
 
 	/* GPIO_11 - TOUCHSCREEN_INT_3V3_ODL, SCI */
-	PAD_GPI(GPIO_11, PULL_UP),
+	PAD_SCI(GPIO_11, PULL_UP, EDGE_LOW),
 
 	/* GPIO_12 - Unused (TP126) */
 	PAD_GPI(GPIO_12, PULL_UP),
@@ -171,7 +173,7 @@ static const struct soc_amd_gpio gpio_set_stage_ram_old[] = {
 	PAD_GPI(GPIO_13, PULL_UP),
 
 	/* GPIO_14 - APU_HP_INT_ODL, SCI */
-	PAD_GPI(GPIO_14, PULL_UP),
+	PAD_SCI(GPIO_14, PULL_UP, EDGE_LOW),
 
 	/* GPIO_16 - USB_C0_OC_L */
 	PAD_NF(GPIO_16, USB_OC0_L, PULL_UP),
@@ -189,7 +191,7 @@ static const struct soc_amd_gpio gpio_set_stage_ram_old[] = {
 	PAD_NF(GPIO_20, I2C3_SDA, PULL_UP),
 
 	/* GPIO_21 - APU_PEN_INT_ODL, SCI */
-	PAD_GPI(GPIO_21, PULL_UP),
+	PAD_SCI(GPIO_21, PULL_UP, EDGE_LOW),
 
 	/* GPIO_24 - USB_A1_OC_ODL */
 	PAD_NF(GPIO_24, USB_OC3_L, PULL_UP),
@@ -314,7 +316,7 @@ static const struct soc_amd_gpio gpio_set_stage_ram[] = {
 	PAD_GPI(GPIO_3, PULL_UP),
 
 	/* GPIO_5 - PCH_TRACKPAD_INT_3V3_ODL, SCI */
-	PAD_GPI(GPIO_5, PULL_UP),
+	PAD_SCI(GPIO_5, PULL_UP, EDGE_LOW),
 
 	/* GPIO_7 - APU_PWROK_OD (currently not used) */
 	PAD_GPI(GPIO_7, PULL_UP),
@@ -326,7 +328,7 @@ static const struct soc_amd_gpio gpio_set_stage_ram[] = {
 	PAD_NF(GPIO_10, S0A3_GPIO, PULL_UP),
 
 	/* GPIO_11 - TOUCHSCREEN_INT_3V3_ODL, SCI */
-	PAD_GPI(GPIO_11, PULL_UP),
+	PAD_SCI(GPIO_11, PULL_UP, EDGE_LOW),
 
 	/* GPIO_12 - EN_PP3300_TRACKPAD */
 	PAD_GPO(GPIO_12, HIGH),
@@ -335,7 +337,7 @@ static const struct soc_amd_gpio gpio_set_stage_ram[] = {
 	PAD_GPI(GPIO_13, PULL_UP),
 
 	/* GPIO_14 - APU_HP_INT_ODL, SCI */
-	PAD_GPI(GPIO_14, PULL_UP),
+	PAD_SCI(GPIO_14, PULL_UP, EDGE_LOW),
 
 	/* GPIO_16 - USB_C0_OC_L */
 	PAD_NF(GPIO_16, USB_OC0_L, PULL_UP),
@@ -353,7 +355,7 @@ static const struct soc_amd_gpio gpio_set_stage_ram[] = {
 	PAD_NF(GPIO_20, I2C3_SDA, PULL_UP),
 
 	/* GPIO_21 - APU_PEN_INT_ODL, SCI */
-	PAD_GPI(GPIO_21, PULL_UP),
+	PAD_SCI(GPIO_21, PULL_UP, EDGE_LOW),
 
 	/* GPIO_25 - SD_CD */
 	PAD_NF(GPIO_25, SD0_CD, PULL_UP),
@@ -486,73 +488,15 @@ struct soc_amd_gpio *variant_gpio_table(size_t *size)
 }
 
 /*
- * GPE setup table must match ACPI GPE ASL
- *  { gevent, gpe, direction, level }
+ * This function is still needed for boards that sets gevents above 23
+ * that will generate SCI or SMI, such as kahlee. Normally this function
+ * points to a table of gevents and what needs to be set. The code that
+ * calls it was modified so that when this function returns NULL then the
+ * caller does nothing.
  */
-static const struct sci_source gpe_table[] = {
-
-	/* PCH_TRACKPAD_INT_3V3_ODL */
-	{
-		.scimap = 7,
-		.gpe = 7,
-		.direction = SMI_SCI_LVL_LOW,
-		.level = SMI_SCI_EDG,
-	},
-
-	/* EC_PCH_WAKE_L */
-	{
-		.scimap = EC_WAKE_GPI,
-		.gpe = EC_WAKE_GPI,
-		.direction = SMI_SCI_LVL_LOW,
-		.level = SMI_SCI_EDG,
-	},
-
-	/* H1_PCH_INT_ODL */
-	{
-		.scimap = 22,
-		.gpe = 22,
-		.direction = SMI_SCI_LVL_LOW,
-		.level = SMI_SCI_EDG,
-	},
-
-	/* TOUCHSCREEN_INT_3V3_ODL */
-	{
-		.scimap = 18,
-		.gpe = 18,
-		.direction = SMI_SCI_LVL_LOW,
-		.level = SMI_SCI_EDG,
-	},
-
-
-	/* APU_HP_INT_ODL */
-	{
-		.scimap = 6,
-		.gpe = 6,
-		.direction = SMI_SCI_LVL_LOW,
-		.level = SMI_SCI_EDG,
-	},
-
-	/* APU_PEN_INT_ODL */
-	{
-		.scimap = 5,
-		.gpe = 5,
-		.direction = SMI_SCI_LVL_LOW,
-		.level = SMI_SCI_EDG,
-	},
-
-	/* EC_SCI_ODL */
-	{
-		.scimap = 3,
-		.gpe = 3,
-		.direction = SMI_SCI_LVL_LOW,
-		.level = SMI_SCI_EDG,
-	},
-};
-
 const __weak struct sci_source *get_gpe_table(size_t *num)
 {
-	*num = ARRAY_SIZE(gpe_table);
-	return gpe_table;
+	return NULL;
 }
 
 int __weak variant_get_xhci_oc_map(uint16_t *map)
diff --git a/src/mainboard/google/kahlee/variants/kahlee/gpio.c b/src/mainboard/google/kahlee/variants/kahlee/gpio.c
index 8f30e4b40e..30723508db 100644
--- a/src/mainboard/google/kahlee/variants/kahlee/gpio.c
+++ b/src/mainboard/google/kahlee/variants/kahlee/gpio.c
@@ -26,7 +26,7 @@
  */
 static const struct soc_amd_gpio gpio_set_stage_reset[] = {
 	/* AGPIO2, to become event generator */
-	PAD_GPI(GPIO_2, PULL_UP),
+	PAD_SCI(GPIO_2, PULL_UP, EDGE_LOW),
 
 	/* SER_TX */
 	PAD_NF(GPIO_8, SerPortTX_OUT, PULL_UP),
@@ -44,7 +44,7 @@ static const struct soc_amd_gpio gpio_set_stage_reset[] = {
 	PAD_NF(GPIO_20, I2C3_SDA, PULL_UP),
 
 	/* AGPIO22 EC_SCI */
-	PAD_GPI(GPIO_22, PULL_UP),
+	PAD_SCI(GPIO_22, PULL_UP, EDGE_LOW),
 
 	/* SPI_TPM_CS_L */
 	PAD_NF(GPIO_76, SPI_TPM_CS_L, PULL_DOWN),
@@ -120,22 +120,6 @@ const struct soc_amd_gpio *variant_gpio_table(size_t *size)
  */
 static const struct sci_source gpe_table[] = {
 
-	/* EC AGPIO22/Gevent3 -> GPE 3 */
-	{
-		.scimap = 3,
-		.gpe = 3,
-		.direction = SMI_SCI_LVL_LOW,
-		.level = SMI_SCI_EDG,
-	},
-
-	/* PCIE/WLAN AGPIO2/Gevent8 -> GPE8 */
-	{
-		.scimap = 8,
-		.gpe = 8,
-		.direction = SMI_SCI_LVL_LOW,
-		.level = SMI_SCI_LVL,
-	},
-
 	/* EHCI USB_PME -> GPE24 */
 	{
 		.scimap = 24,