- Add support _framework_ for the Asus p2b.

- New superIO winbond/w83977tf
- Add single memory controller SBbus debug routine
into a file private to the i440bx

This adds support the start of support for an Asus p2b
mainboard.  Current limitations are the same as for the 
Bitworks IMS board.  Reads from the SMbus don't work.

Moving dump_spd_registers() into its own private copy
solves the problem of having to go hack on the version that
included in src/sdram to only do one memory controller.




git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2351 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

10 files changed, 709 insertions, 0 deletions

diff --git a/src/mainboard/asus/p2b/Config.lb b/src/mainboard/asus/p2b/Config.lb
new file mode 100644
index 0000000000..357a1013ff
--- /dev/null
+++ b/src/mainboard/asus/p2b/Config.lb
@@ -0,0 +1,136 @@
+##
+## Compute the location and size of where this firmware image
+## (linuxBIOS plus bootloader) will live in the boot rom chip.
+##
+if USE_FALLBACK_IMAGE
+	default ROM_SECTION_SIZE   = FALLBACK_SIZE
+	default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
+else
+	default ROM_SECTION_SIZE   = ( ROM_SIZE - FALLBACK_SIZE )
+	default ROM_SECTION_OFFSET = 0
+end
+
+##
+## Compute the start location and size size of
+## The linuxBIOS bootloader.
+##
+default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+default PAYLOAD_SIZE            = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+
+##
+## Compute where this copy of linuxBIOS will start in the boot rom
+##
+default _ROMBASE      = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up linuxBIOS,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+default XIP_ROM_SIZE=65536
+default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+
+##
+## Set all of the defaults for an x86 architecture
+##
+
+arch i386 end
+
+##
+## Build the objects we have code for in this directory.
+##
+
+driver mainboard.o
+
+#if HAVE_PIRQ_TABLE object irq_tables.o end
+#object reset.o
+
+##
+## Romcc output
+##
+makerule ./failover.E
+	depends "$(MAINBOARD)/failover.c ./romcc" 
+	action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+end
+
+makerule ./failover.inc
+	depends "$(MAINBOARD)/failover.c ./romcc"
+	action "./romcc    -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+end
+
+makerule ./auto.E 
+	depends	"$(MAINBOARD)/auto.c option_table.h ./romcc" 
+	action	"./romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+makerule ./auto.inc 
+	depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+	action	"./romcc    -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+
+##
+## Build our 16 bit and 32 bit linuxBIOS entry code
+##
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
+
+##
+## Build our reset vector (This is where linuxBIOS is entered)
+##
+if USE_FALLBACK_IMAGE 
+	mainboardinit cpu/x86/16bit/reset16.inc 
+	ldscript /cpu/x86/16bit/reset16.lds 
+else
+	mainboardinit cpu/x86/32bit/reset32.inc 
+	ldscript /cpu/x86/32bit/reset32.lds 
+end
+
+### Should this be in the northbridge code?
+mainboardinit arch/i386/lib/cpu_reset.inc
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+
+###
+### This is the early phase of linuxBIOS startup 
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+if USE_FALLBACK_IMAGE
+	ldscript /arch/i386/lib/failover.lds 
+	mainboardinit ./failover.inc
+end
+
+###
+### O.k. We aren't just an intermediary anymore!
+###
+
+##
+## Setup RAM
+##
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+mainboardinit cpu/x86/mmx/enable_mmx.inc
+mainboardinit ./auto.inc
+mainboardinit cpu/x86/mmx/disable_mmx.inc
+
+##
+## Include the secondary Configuration files 
+##
+dir /pc80
+config chip.h
+
+chip northbridge/intel/i440bx
+   device pci_domain 0 on 
+   end
+
+   chip cpu/intel/socket_PGA370
+   end
+
+end
+
diff --git a/src/mainboard/asus/p2b/Options.lb b/src/mainboard/asus/p2b/Options.lb
new file mode 100644
index 0000000000..20c1aaa310
--- /dev/null
+++ b/src/mainboard/asus/p2b/Options.lb
@@ -0,0 +1,155 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses HAVE_OPTION_TABLE
+uses USE_OPTION_TABLE
+uses CONFIG_ROM_STREAM
+uses IRQ_SLOT_COUNT
+uses MAINBOARD
+uses MAINBOARD_VENDOR
+uses MAINBOARD_PART_NUMBER
+uses LINUXBIOS_EXTRA_VERSION
+uses ARCH
+uses FALLBACK_SIZE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM_START
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses _RAMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses HAVE_MP_TABLE
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses OBJCOPY
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_CONSOLE_SERIAL8250
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses CONFIG_UDELAY_TSC
+
+## ROM_SIZE is the size of boot ROM that this board will use.
+default ROM_SIZE  = 256*1024
+
+###
+### Build options
+###
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## no MP table
+##
+default HAVE_MP_TABLE=0
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=0
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=0
+default IRQ_SLOT_COUNT=4
+#object irq_tables.o
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=0
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 65536
+default FALLBACK_SIZE = 131072
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default USE_OPTION_TABLE = 0
+
+default _RAMBASE = 0x00004000
+
+default CONFIG_ROM_STREAM     = 1
+
+##
+## The default compiler
+##
+default CROSS_COMPILE=""
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG      1   system is unusable               
+## ALERT      2   action must be taken immediately 
+## CRIT       3   critical conditions              
+## ERR        4   error conditions                 
+## WARNING    5   warning conditions               
+## NOTICE     6   normal but significant condition 
+## INFO       7   informational                    
+## DEBUG      8   debug-level messages             
+## SPEW       9   Way too many details             
+
+## Request this level of debugging output
+default  DEFAULT_CONSOLE_LOGLEVEL=9
+## At a maximum only compile in this level of debugging
+default  MAXIMUM_CONSOLE_LOGLEVEL=9
+
+default CONFIG_UDELAY_TSC=1
+end
+
diff --git a/src/mainboard/asus/p2b/auto.c b/src/mainboard/asus/p2b/auto.c
new file mode 100644
index 0000000000..65d0ae7cc2
--- /dev/null
+++ b/src/mainboard/asus/p2b/auto.c
@@ -0,0 +1,154 @@
+#define ASSEMBLY 1
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/hlt.h>
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "southbridge/intel/i440bx/i440bx_early_smbus.c"
+#include "superio/winbond/w83977tf/w83977tf_early_serial.c"
+#include "northbridge/intel/i440bx/raminit.h"
+#include "cpu/x86/mtrr/earlymtrr.c"
+#include "cpu/x86/bist.h"
+
+#define SERIAL_DEV PNP_DEV(0x3f0, W83977TF_SP1)
+
+/*
+ */
+void udelay(int usecs) 
+{
+	int i;
+	for(i = 0; i < usecs; i++)
+		outb(i&0xff, 0x80);
+}
+
+#include "debug.c"
+#include "lib/delay.c"
+
+
+static void memreset_setup(void)
+{
+}
+
+/*
+  static void memreset(int controllers, const struct mem_controller *ctrl)
+  {
+  }
+*/
+
+
+static void enable_mainboard_devices(void) 
+{
+	device_t dev;
+	/* dev 0 for southbridge */
+  
+	dev = pci_locate_device(PCI_ID(0x1106,0x8231), 0);
+  
+	if (dev == PCI_DEV_INVALID) {
+		die("Southbridge not found!!!\n");
+	}
+	pci_write_config8(dev, 0x50, 7);
+	pci_write_config8(dev, 0x51, 0xff);
+#if 0
+	// This early setup switches IDE into compatibility mode before PCI gets 
+	// // a chance to assign I/Os
+	//         movl    $CONFIG_ADDR(0, 0x89, 0x42), %eax
+	//         //      movb    $0x09, %dl
+	//                 movb    $0x00, %dl
+	//                         PCI_WRITE_CONFIG_BYTE
+	//
+#endif
+	/* we do this here as in V2, we can not yet do raw operations 
+	 * to pci!
+	 */
+        dev += 0x100; /* ICKY */
+
+	pci_write_config8(dev, 0x42, 0);
+}
+
+static void enable_shadow_ram(void) 
+{
+	device_t dev = 0; /* no need to look up 0:0.0 */
+	unsigned char shadowreg;
+	/* dev 0 for southbridge */
+	shadowreg = pci_read_config8(dev, 0x63);
+	/* 0xf0000-0xfffff */
+	shadowreg |= 0x30;
+	pci_write_config8(dev, 0x63, shadowreg);
+}
+
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+	unsigned char c;
+	c = smbus_read_byte(device, address);
+	return c;
+}
+
+
+#include "northbridge/intel/i440bx/raminit.c"
+#include "northbridge/intel/i440bx/debug.c"
+#include "sdram/generic_sdram.c"
+
+static void main(unsigned long bist)
+{
+	static const struct mem_controller cpu[] = {
+		{
+		 .channel0 = {
+			 (0xa << 3) | 0,
+			 (0xa << 3) | 1,
+			 (0xa << 3) | 2, (0xa << 3) | 3,
+		 	},
+		 }
+	};
+	unsigned long x;
+	
+	if (bist == 0) {
+		early_mtrr_init();
+	}
+	w83977tf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+	uart_init();
+	console_init();
+
+	/* Halt if there was a built in self test failure */
+	report_bist_failure(bist);
+
+	enable_smbus();
+	dump_spd_registers(&cpu[0]);
+
+#if 0
+	enable_shadow_ram();
+	/*
+	  memreset_setup();
+	  this is way more generic than we need.
+	  sdram_initialize(sizeof(cpu)/sizeof(cpu[0]), cpu);
+	*/
+	sdram_set_registers((const struct mem_controller *) 0);
+	sdram_set_spd_registers((const struct mem_controller *) 0);
+	sdram_enable(0, (const struct mem_controller *) 0);
+#endif
+	
+	/* Check all of memory */
+#if 0
+	ram_check(0x00000000, msr.lo);
+#endif
+#if 0
+	static const struct {
+		unsigned long lo, hi;
+	} check_addrs[] = {
+		/* Check 16MB of memory @ 0*/
+		{ 0x00000000, 0x01000000 },
+#if TOTAL_CPUS > 1
+		/* Check 16MB of memory @ 2GB */
+		{ 0x80000000, 0x81000000 },
+#endif
+	};
+	int i;
+	for(i = 0; i < sizeof(check_addrs)/sizeof(check_addrs[0]); i++) {
+		ram_check(check_addrs[i].lo, check_addrs[i].hi);
+	}
+#endif
+}
diff --git a/src/mainboard/asus/p2b/chip.h b/src/mainboard/asus/p2b/chip.h
new file mode 100644
index 0000000000..a2ab25dfe8
--- /dev/null
+++ b/src/mainboard/asus/p2b/chip.h
@@ -0,0 +1,5 @@
+extern struct chip_operations mainboard_asus_p2b_ops;
+
+struct mainboard_asus_p2b_config {
+	int nothing;
+};
diff --git a/src/mainboard/asus/p2b/cmos.layout b/src/mainboard/asus/p2b/cmos.layout
new file mode 100644
index 0000000000..5ba4c032c1
--- /dev/null
+++ b/src/mainboard/asus/p2b/cmos.layout
@@ -0,0 +1,74 @@
+entries
+
+#start-bit length  config config-ID    name
+#0            8       r       0        seconds
+#8            8       r       0        alarm_seconds
+#16           8       r       0        minutes
+#24           8       r       0        alarm_minutes
+#32           8       r       0        hours
+#40           8       r       0        alarm_hours
+#48           8       r       0        day_of_week
+#56           8       r       0        day_of_month
+#64           8       r       0        month
+#72           8       r       0        year
+#80           4       r       0        rate_select
+#84           3       r       0        REF_Clock
+#87           1       r       0        UIP
+#88           1       r       0        auto_switch_DST
+#89           1       r       0        24_hour_mode
+#90           1       r       0        binary_values_enable
+#91           1       r       0        square-wave_out_enable
+#92           1       r       0        update_finished_enable
+#93           1       r       0        alarm_interrupt_enable
+#94           1       r       0        periodic_interrupt_enable
+#95           1       r       0        disable_clock_updates
+#96         288       r       0        temporary_filler
+0          384       r       0        reserved_memory
+384          1       e       4        boot_option
+385          1       e       4        last_boot
+386          1       e       1        ECC_memory
+388          4       r       0        reboot_bits
+392          3       e       5        baud_rate
+400          1       e       1        power_on_after_fail
+412          4       e       6        debug_level
+416          4       e       7        boot_first
+420          4       e       7        boot_second
+424          4       e       7        boot_third
+428          4       h       0        boot_index
+432	     8       h       0        boot_countdown
+1008         16      h       0        check_sum
+
+enumerations
+
+#ID value   text
+1     0     Disable
+1     1     Enable
+2     0     Enable
+2     1     Disable
+4     0     Fallback
+4     1     Normal
+5     0     115200
+5     1     57600
+5     2     38400
+5     3     19200
+5     4     9600
+5     5     4800
+5     6     2400
+5     7     1200
+6     6     Notice
+6     7     Info
+6     8     Debug
+6     9     Spew
+7     0     Network
+7     1     HDD
+7     2     Floppy
+7     8     Fallback_Network
+7     9     Fallback_HDD
+7     10    Fallback_Floppy
+#7     3     ROM
+
+checksums
+
+checksum 392 1007 1008
+
+
diff --git a/src/mainboard/asus/p2b/debug.c b/src/mainboard/asus/p2b/debug.c
new file mode 100644
index 0000000000..7eeabdef47
--- /dev/null
+++ b/src/mainboard/asus/p2b/debug.c
@@ -0,0 +1,66 @@
+
+static void print_debug_pci_dev(unsigned dev)
+{
+	print_debug("PCI: ");
+	print_debug_hex8((dev >> 16) & 0xff);
+	print_debug_char(':');
+	print_debug_hex8((dev >> 11) & 0x1f);
+	print_debug_char('.');
+	print_debug_hex8((dev >> 8) & 7);
+}
+
+static void print_pci_devices(void)
+{
+	device_t dev;
+	for(dev = PCI_DEV(0, 0, 0); 
+		dev <= PCI_DEV(0, 0x1f, 0x7); 
+		dev += PCI_DEV(0,0,1)) {
+		uint32_t id;
+		id = pci_read_config32(dev, PCI_VENDOR_ID);
+		if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0x0000)) {
+			continue;
+		}
+		print_debug_pci_dev(dev);
+		print_debug("\r\n");
+	}
+}
+
+static void dump_pci_device(unsigned dev)
+{
+	int i;
+	print_debug_pci_dev(dev);
+	print_debug("\r\n");
+	
+	for(i = 0; i <= 255; i++) {
+		unsigned char val;
+		if ((i & 0x0f) == 0) {
+			print_debug_hex8(i);
+			print_debug_char(':');
+		}
+		val = pci_read_config8(dev, i);
+		print_debug_char(' ');
+		print_debug_hex8(val);
+		if ((i & 0x0f) == 0x0f) {
+			print_debug("\r\n");
+		}
+	}
+}
+
+static void dump_pci_devices(void)
+{
+	device_t dev;
+	for(dev = PCI_DEV(0, 0, 0); 
+		dev <= PCI_DEV(0, 0x1f, 0x7); 
+		dev += PCI_DEV(0,0,1)) {
+		uint32_t id;
+		id = pci_read_config32(dev, PCI_VENDOR_ID);
+		if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0xffff) ||
+			(((id >> 16) & 0xffff) == 0x0000)) {
+			continue;
+		}
+		dump_pci_device(dev);
+	}
+}
diff --git a/src/mainboard/asus/p2b/failover.c b/src/mainboard/asus/p2b/failover.c
new file mode 100644
index 0000000000..bdcb9eaed2
--- /dev/null
+++ b/src/mainboard/asus/p2b/failover.c
@@ -0,0 +1,32 @@
+#define ASSEMBLY 1
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include "arch/romcc_io.h"
+#include "pc80/mc146818rtc_early.c"
+
+static unsigned long main(unsigned long bist)
+{
+	/* This is the primary cpu how should I boot? */
+	if (do_normal_boot()) {
+		goto normal_image;
+	}
+	else {
+		goto fallback_image;
+	}
+ normal_image:
+	asm volatile ("jmp __normal_image" 
+		: /* outputs */ 
+		: "a" (bist) /* inputs */
+		: /* clobbers */
+		);
+ cpu_reset:
+	asm volatile ("jmp __cpu_reset"
+		: /* outputs */ 
+		: "a"(bist) /* inputs */
+		: /* clobbers */
+		);
+ fallback_image:
+	return bist;
+}
diff --git a/src/mainboard/asus/p2b/irq_tables.c b/src/mainboard/asus/p2b/irq_tables.c
new file mode 100644
index 0000000000..894c27dec5
--- /dev/null
+++ b/src/mainboard/asus/p2b/irq_tables.c
@@ -0,0 +1,32 @@
+/* This file was generated by getpir.c, do not modify! 
+   (but if you do, please run checkpir on it to verify)
+   Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up
+
+   Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+
+#include <arch/pirq_routing.h>
+
+const struct irq_routing_table intel_irq_routing_table = {
+	PIRQ_SIGNATURE, /* u32 signature */
+	PIRQ_VERSION,   /* u16 version   */
+	32+16*5,        /* there can be total 5 devices on the bus */
+	0,              /* Where the interrupt router lies (bus) */
+	0x88,           /* Where the interrupt router lies (dev) */
+	0x1c20,         /* IRQs devoted exclusively to PCI usage */
+	0x1106,         /* Vendor */
+	0x8231,         /* Device */
+	0,              /* Crap (miniport) */
+	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+	0x5e,         /*  u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+	{
+		/* 8231 ethernet */
+		{0,0x90, {{0x1, 0xdeb8}, {0x2, 0xdeb8}, {0x3, 0xdeb8}, {0x4, 0xdeb8}}, 0x1, 0},
+		/* 8231 internal */
+		{0,0x88, {{0x2, 0xdeb8}, {0x3, 0xdeb8}, {0x4, 0xdeb8}, {0x1, 0xdeb8}}, 0x2, 0},
+		/* PCI slot */
+		{0,0xa0, {{0x3, 0xdeb8}, {0x4, 0xdeb8}, {0x1, 0xdeb8}, {0x2, 0xdeb8}}, 0, 0},
+		{0,0x50, {{0x4, 0xdeb8}, {0x3, 0xdeb8}, {0x2, 0xdeb8}, {0x1, 0xdeb8}}, 0x3, 0},
+		{0,0x98, {{0x4, 0xdeb8}, {0x3, 0xdeb8}, {0x2, 0xdeb8}, {0x1, 0xdeb8}}, 0x4, 0},
+	}
+};
diff --git a/src/mainboard/asus/p2b/mainboard.c b/src/mainboard/asus/p2b/mainboard.c
new file mode 100644
index 0000000000..94966aa689
--- /dev/null
+++ b/src/mainboard/asus/p2b/mainboard.c
@@ -0,0 +1,12 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <arch/io.h>
+#include "chip.h"
+
+struct chip_operations mainboard_asus_p2b_ops = {
+	CHIP_NAME("ASUS P2B mainboard ")
+};
+
diff --git a/src/mainboard/asus/p2b/reset.c b/src/mainboard/asus/p2b/reset.c
new file mode 100644
index 0000000000..5796e17dc8
--- /dev/null
+++ b/src/mainboard/asus/p2b/reset.c
@@ -0,0 +1,43 @@
+#if 0
+//#include "arch/romcc_io.h"
+#include <arch/io.h>
+
+typedef unsigned device_t;
+
+#define PCI_DEV(BUS, DEV, FN) ( \
+	(((BUS) & 0xFF) << 16) | \
+	(((DEV) & 0x1f) << 11) | \
+	(((FN)  & 0x7) << 8))
+
+static void pci_write_config8(device_t dev, unsigned where, unsigned char value)
+{
+        unsigned addr;
+        addr = dev | where;
+        outl(0x80000000 | (addr & ~3), 0xCF8);
+        outb(value, 0xCFC + (addr & 3));
+}
+
+static void pci_write_config32(device_t dev, unsigned where, unsigned value)
+{
+	unsigned addr;
+        addr = dev | where;
+        outl(0x80000000 | (addr & ~3), 0xCF8);
+        outl(value, 0xCFC);
+}
+
+static unsigned pci_read_config32(device_t dev, unsigned where)
+{
+	unsigned addr;
+        addr = dev | where;
+        outl(0x80000000 | (addr & ~3), 0xCF8);
+        return inl(0xCFC);
+}
+
+#include "../../../northbridge/amd/amdk8/reset_test.c"
+
+void hard_reset(void)
+{
+	set_bios_reset();
+	pci_write_config8(PCI_DEV(1, 0x04, 0), 0x47, 1);
+}
+#endif