path: root/src/vendorcode/intel/fsp/fsp2_0/elkhartlake/FspsUpd.h

/** @file

Copyright (c) 2020, Intel Corporation. All rights reserved.<BR>

Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this
  list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
  list of conditions and the following disclaimer in the documentation and/or
  other materials provided with the distribution.
* Neither the name of Intel Corporation nor the names of its contributors may
  be used to endorse or promote products derived from this software without
  specific prior written permission.

  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
  THE POSSIBILITY OF SUCH DAMAGE.

  This file is automatically generated. Please do NOT modify !!!

**/

#ifndef __FSPSUPD_H__
#define __FSPSUPD_H__

#include <FspUpd.h>

#pragma pack(1)


///
/// Azalia Header structure
///
typedef struct {
  UINT16 VendorId;           ///< Codec Vendor ID
  UINT16 DeviceId;           ///< Codec Device ID
  UINT8  RevisionId;         ///< Revision ID of the codec. 0xFF matches any revision.
  UINT8  SdiNum;             ///< SDI number, 0xFF matches any SDI.
  UINT16 DataDwords;         ///< Number of data DWORDs pointed by the codec data buffer.
  UINT32 Reserved;           ///< Reserved for future use. Must be set to 0.
} AZALIA_HEADER;

///
/// Audio Azalia Verb Table structure
///
typedef struct {
  AZALIA_HEADER Header;      ///< AZALIA PCH header
  UINT32        *Data;       ///< Pointer to the data buffer. Its length is specified in the header
} AUDIO_AZALIA_VERB_TABLE;

///
/// Refer to the definition of PCH_INT_PIN
///
typedef enum {
  SiPchNoInt,        ///< No Interrupt Pin
  SiPchIntA,
  SiPchIntB,
  SiPchIntC,
  SiPchIntD
} SI_PCH_INT_PIN;
///
/// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device.
///
typedef struct {
  UINT8        Device;                  ///< Device number
  UINT8        Function;                ///< Device function
  UINT8        IntX;                    ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN)
  UINT8        Irq;                     ///< IRQ to be set for device.
} SI_PCH_DEVICE_INTERRUPT_CONFIG;

#define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG  64       ///< Number of all PCH devices


/** Fsp S Configuration
**/
typedef struct {

/** Offset 0x0020 - Logo Pointer
  Points to PEI Display Logo Image
**/
  UINT32                      LogoPtr;

/** Offset 0x0024 - Logo Size
  Size of PEI Display Logo Image
**/
  UINT32                      LogoSize;

/** Offset 0x0028 - Blt Buffer Address
  Address of Blt buffer
**/
  UINT32                      BltBufferAddress;

/** Offset 0x002C - Blt Buffer Size
  Size of Blt Buffer, is equal to PixelWidth * PixelHeight * 4 bytes (the size of
  EFI_GRAPHICS_OUTPUT_BLT_PIXEL)
**/
  UINT32                      BltBufferSize;

/** Offset 0x0030 - Graphics Configuration Ptr
  Points to VBT
**/
  UINT32                      GraphicsConfigPtr;

/** Offset 0x0034 - Enable Device 4
  Enable/disable Device 4
  $EN_DIS
**/
  UINT8                       Device4Enable;

/** Offset 0x0035 - Enable eMMC Controller
  Enable/disable eMMC Controller.
  $EN_DIS
**/
  UINT8                       ScsEmmcEnabled;

/** Offset 0x0036 - Enable eMMC HS400 Mode
  Enable eMMC HS400 Mode.
  $EN_DIS
**/
  UINT8                       ScsEmmcHs400Enabled;

/** Offset 0x0037 - Enable eMMC DDR50 Mode
  Enable eMMC DDR50 Mode.
  $EN_DIS
**/
  UINT8                       ScsEmmcDdr50Enabled;

/** Offset 0x0038 - Use DLL values from policy
  Set if FSP should use HS400 DLL values from policy
  $EN_DIS
**/
  UINT8                       EmmcUseCustomDlls;

/** Offset 0x0039
**/
  UINT8                       UnusedUpdSpace0[3];

/** Offset 0x003C - Emmc Tx CMD Delay control register value
  Please see Tx CMD Delay Control register definition for help
**/
  UINT32                      EmmcTxCmdDelayRegValue;

/** Offset 0x0040 - Emmc Tx DATA Delay control 1 register value
  Please see Tx DATA Delay control 1 register definition for help
**/
  UINT32                      EmmcTxDataDelay1RegValue;

/** Offset 0x0044 - Emmc Tx DATA Delay control 2 register value
  Please see Tx DATA Delay control 2 register definition for help
**/
  UINT32                      EmmcTxDataDelay2RegValue;

/** Offset 0x0048 - Emmc Rx CMD + DATA Delay control 1 register value
  Please see Rx CMD + DATA Delay control 1 register definition for help
**/
  UINT32                      EmmcRxCmdDataDelay1RegValue;

/** Offset 0x004C - Emmc Rx CMD + DATA Delay control 2 register value
  Please see Rx CMD + DATA Delay control 2 register definition for help
**/
  UINT32                      EmmcRxCmdDataDelay2RegValue;

/** Offset 0x0050 - Emmc Rx Strobe Delay control register value
  Please see Rx Strobe Delay control register definition for help
**/
  UINT32                      EmmcRxStrobeDelayRegValue;

/** Offset 0x0054 - Enable SdCard Controller
  Enable/disable SD Card Controller.
  $EN_DIS
**/
  UINT8                       ScsSdCardEnabled;

/** Offset 0x0055 - SdCard power enable polarity
  Choose SD_PWREN# polarity
  0: Active low, 1: Active high
**/
  UINT8                       SdCardPowerEnableActiveHigh;

/** Offset 0x0056 - Use tuned DLL values from policy
  Set if FSP should use HS400 DLL values from policy
  $EN_DIS
**/
  UINT8                       SdCardUseCustomDlls;

/** Offset 0x0057
**/
  UINT8                       UnusedUpdSpace1;

/** Offset 0x0058 - SdCard Tx CMD Delay control register value
  Please see Tx CMD Delay Control register definition for help
**/
  UINT32                      SdCardTxCmdDelayRegValue;

/** Offset 0x005C - SdCard Tx DATA Delay control 1 register value
  Please see Tx DATA Delay control 1 register definition for help
**/
  UINT32                      SdCardTxDataDelay1RegValue;

/** Offset 0x0060 - SdCard Tx DATA Delay control 2 register value
  Please see Tx DATA Delay control 2 register definition for help
**/
  UINT32                      SdCardTxDataDelay2RegValue;

/** Offset 0x0064 - SdCard Rx CMD + DATA Delay control 1 register value
  Please see Rx CMD + DATA Delay control 1 register definition for help
**/
  UINT32                      SdCardRxCmdDataDelay1RegValue;

/** Offset 0x0068 - SdCard Rx CMD + DATA Delay control 2 register value
  Please see Rx CMD + DATA Delay control 2 register definition for help
**/
  UINT32                      SdCardRxCmdDataDelay2RegValue;

/** Offset 0x006C - SdCard Power Enable Pin Mux
  Select Power Enable pin muxing. Refer to GPIO_*_MUXING_SDCARD_PWR_EN* for possible values.
**/
  UINT32                      SdCardGpioPrwEnBPinMux;

/** Offset 0x0070 - SdCard Power Enable Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       SdCardGpioPrwEnBPadTermination;

/** Offset 0x0071
**/
  UINT8                       UnusedUpdSpace2[3];

/** Offset 0x0074 - SdCard Command Pin Mux
  Select Command pin muxing. Refer to GPIO_*_MUXING_SDCARD_CMD* for possible values.
**/
  UINT32                      SdCardGpioCmdPinMux;

/** Offset 0x0078 - SdCard Command Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       SdCardGpioCmdPadTermination;

/** Offset 0x0079
**/
  UINT8                       UnusedUpdSpace3[3];

/** Offset 0x007C - SdCard Data Pin Mux
  Select Data pin muxing. Refer to GPIO_*_MUXING_SDCARD_DATAx_* for possible values.
  One UINT32 for each data pin [0-4]
**/
  UINT32                      SdCardGpioDataPinMux[4];

/** Offset 0x008C - SdCard Data Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up. One byte for each data pin [0-4]
**/
  UINT8                       SdCardGpioDataPadTermination[4];

/** Offset 0x0090 - SdCard Cdb Pin Mux
  Select Cdb pin muxing. Refer to GPIO_*_MUXING_SDCARD_CDB* for possible values.
**/
  UINT32                      SdCardGpioCdbPinMux;

/** Offset 0x0094 - SdCard Cdb Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       SdCardGpioCdbPadTermination;

/** Offset 0x0095
**/
  UINT8                       UnusedUpdSpace4[3];

/** Offset 0x0098 - SdCard Clock Pin Mux
  Select Clock pin muxing. Refer to GPIO_*_MUXING_SDCARD_CLK* for possible values.
**/
  UINT32                      SdCardGpioClkPinMux;

/** Offset 0x009C - SdCard Clock Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       SdCardGpioClkPadTermination;

/** Offset 0x009D
**/
  UINT8                       UnusedUpdSpace5[3];

/** Offset 0x00A0 - SdCard Wp PinMux
  Select Wp pin muxing. Refer to GPIO_*_MUXING_SDCARD_WP* for possible values.
**/
  UINT32                      SdCardGpioWpPinMux;

/** Offset 0x00A4 - SdCard Wp Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       SdCardGpioWpPadTermination;

/** Offset 0x00A5
**/
  UINT8                       UnusedUpdSpace6[3];

/** Offset 0x00A8 - SdCard Clock Feedback Pin Mux
  Select  pin muxing. Refer to GPIO_*_MUXING_SDCARD_CLK_FB* for possible values.
**/
  UINT32                      SdCardGpioClkFbPinMux;

/** Offset 0x00AC - SdCard Clock Feedback Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       SdCardGpioClkFbPadTermination;

/** Offset 0x00AD
**/
  UINT8                       UnusedUpdSpace7[3];

/** Offset 0x00B0 - Emmc Command Pin Mux
  Select  pin muxing. Refer to GPIO_*_MUXING_EMMC_CMD* for possible values.
**/
  UINT32                      EmmcGpioCmdPinMux;

/** Offset 0x00B4 - Emmc Command Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       EmmcGpioCmdPadTermination;

/** Offset 0x00B5 - Emmc Data Pin Mux
  Select  pin muxing. Refer to GPIO_*_MUXING_EMMC_DATA_x* for possible values. One
  UINT32 for each data pin [0-8]
**/
  UINT8                       EmmcGpioDataPinMux[32];

/** Offset 0x00D5 - Emmc Data Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up. One byte for each data pin [0-8]
**/
  UINT8                       EmmcGpioDataPadTermination[8];

/** Offset 0x00DD
**/
  UINT8                       UnusedUpdSpace8[3];

/** Offset 0x00E0 - Emmc Rclk PinMux
  Select Rclk pin muxing. Refer to GPIO_*_MUXING_EMMC_RCLK* for possible values.
**/
  UINT32                      EmmcGpioRclkPinMux;

/** Offset 0x00E4 - Emmc Rclk Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       EmmcGpioRclkPadTermination;

/** Offset 0x00E5
**/
  UINT8                       UnusedUpdSpace9[3];

/** Offset 0x00E8 - Emmc Clock Pin Mux
  Select Clock pin muxing. Refer to GPIO_*_MUXING_EMMC_CLK* for possible values.
**/
  UINT32                      EmmcGpioClkPinMux;

/** Offset 0x00EC - Emmc Clock Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       EmmcGpioClkPadTermination;

/** Offset 0x00ED
**/
  UINT8                       UnusedUpdSpace10[3];

/** Offset 0x00F0 - Emmc Resetb PinMux
  Select Resetb pin muxing. Refer to GPIO_*_MUXING_EMMC_RESETB* for possible values.
**/
  UINT32                      EmmcGpioResetbPinMux;

/** Offset 0x00F4 - Emmc Resetb Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       EmmcGpioResetbPadTermination;

/** Offset 0x00F5
**/
  UINT8                       UnusedUpdSpace11[3];

/** Offset 0x00F8 - Emmc HipMon PinMux
  Select HipMon pin muxing. Refer to GPIO_*_MUXING_EMMC_HIP_MON* for possible values.
**/
  UINT32                      EmmcGpioHipMonPinMux;

/** Offset 0x00FC - Emmc HipMon Pad Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up
**/
  UINT8                       EmmcGpioHipMonPadTermination;

/** Offset 0x00FD - Show SPI controller
  Enable/disable to show SPI controller.
  $EN_DIS
**/
  UINT8                       ShowSpiController;

/** Offset 0x00FE
**/
  UINT8                       UnusedUpdSpace12[2];

/** Offset 0x0100 - MicrocodeRegionBase
  Memory Base of Microcode Updates
**/
  UINT32                      MicrocodeRegionBase;

/** Offset 0x0104 - MicrocodeRegionSize
  Size of Microcode Updates
**/
  UINT32                      MicrocodeRegionSize;

/** Offset 0x0108 - SiipRegionBase
  Memory Base of Siip Firmware
**/
  UINT32                      SiipRegionBase;

/** Offset 0x010C - SiipRegionSize
  Size of Siip Firmware
**/
  UINT32                      SiipRegionSize;

/** Offset 0x0110 - Turbo Mode
  Enable/Disable Turbo mode. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       TurboMode;

/** Offset 0x0111 - Enable SATA SALP Support
  Enable/disable SATA Aggressive Link Power Management.
  $EN_DIS
**/
  UINT8                       SataSalpSupport;

/** Offset 0x0112 - PCH Sata Port Multiplier
  Enable / Disable SATA Port Multiplier
  $EN_DIS
**/
  UINT8                       SataPortMultiplier;

/** Offset 0x0113 - Enable SATA ports
  Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1,
  and so on.
**/
  UINT8                       SataPortsEnable[8];

/** Offset 0x011B - Enable SATA DEVSLP Feature
  Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each
  port, byte0 for port0, byte1 for port1, and so on.
**/
  UINT8                       SataPortsDevSlp[8];

/** Offset 0x0123 - Enable USB2 ports
  Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for
  port1, and so on.
**/
  UINT8                       PortUsb20Enable[16];

/** Offset 0x0133 - Enable USB2 ports OTG
  Selectively Enable/Disable USB2 OTG Mode. One byte for each port, byte0 for port0,
  byte1 for port1, and so on.
**/
  UINT8                       USB20Otg[16];

/** Offset 0x0143 - Enable USB3 ports OTG
  Selectively Enable/Disable USB3 OTG Mode. One byte for each port, byte0 for port0,
  byte1 for port1, and so on.
**/
  UINT8                       USB30Otg[10];

/** Offset 0x014D - Enable USB3 ports
  Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for
  port1, and so on.
**/
  UINT8                       PortUsb30Enable[10];

/** Offset 0x0157 - Enable xDCI controller
  Enable/disable to xDCI controller.
  $EN_DIS
**/
  UINT8                       XdciEnable;

/** Offset 0x0158 - Address of PCH_DEVICE_INTERRUPT_CONFIG table.
  The address of the table of PCH_DEVICE_INTERRUPT_CONFIG.
**/
  UINT32                      DevIntConfigPtr;

/** Offset 0x015C - Number of DevIntConfig Entry
  Number of Device Interrupt Configuration Entry. If this is not zero, the DevIntConfigPtr
  must not be NULL.
**/
  UINT8                       NumOfDevIntConfig;

/** Offset 0x015D - PIRQx to IRQx Map Config
  PIRQx to IRQx mapping. The valid value is 0x00 to 0x0F for each. First byte is for
  PIRQA, second byte is for PIRQB, and so on. The setting is only available in Legacy
  8259 PCI mode.
**/
  UINT8                       PxRcConfig[8];

/** Offset 0x0165 - Select GPIO IRQ Route
  GPIO IRQ Select. The valid value is 14 or 15.
**/
  UINT8                       GpioIrqRoute;

/** Offset 0x0166 - Select SciIrqSelect
  SCI IRQ Select. The valid value is 9, 10, 11, and 20, 21, 22, 23 for APIC only.
**/
  UINT8                       SciIrqSelect;

/** Offset 0x0167 - Select TcoIrqSelect
  TCO IRQ Select. The valid value is 9, 10, 11, 20, 21, 22, 23.
**/
  UINT8                       TcoIrqSelect;

/** Offset 0x0168 - Enable/Disable Tco IRQ
  Enable/disable TCO IRQ
  $EN_DIS
**/
  UINT8                       TcoIrqEnable;

/** Offset 0x0169 - PCH HDA Verb Table Entry Number
  Number of Entries in Verb Table.
**/
  UINT8                       PchHdaVerbTableEntryNum;

/** Offset 0x016A
**/
  UINT8                       UnusedUpdSpace13[2];

/** Offset 0x016C - PCH HDA Verb Table Pointer
  Pointer to Array of pointers to Verb Table.
**/
  UINT32                      PchHdaVerbTablePtr;

/** Offset 0x0170 - PCH HDA Codec Sx Wake Capability
  Capability to detect wake initiated by a codec in Sx
**/
  UINT8                       PchHdaCodecSxWakeCapability;

/** Offset 0x0171 - Enable SATA
  Enable/disable SATA controller.
  $EN_DIS
**/
  UINT8                       SataEnable;

/** Offset 0x0172 - SATA Mode
  Select SATA controller working mode.
  0:AHCI, 1:RAID
**/
  UINT8                       SataMode;

/** Offset 0x0173 - SPIn Device Mode
  Selects SPI operation mode. N represents controller index: SPI0, SPI1, ... Available
  modes: 0:SerialIoSpiDisabled, 1:SerialIoSpiPci, 2:SerialIoSpiHidden
**/
  UINT8                       SerialIoSpiMode[7];

/** Offset 0x017A - SPI<N> Chip Select Polarity
  Sets polarity for each chip Select. Available options: 0:SerialIoSpiCsActiveLow,
  1:SerialIoSpiCsActiveHigh
**/
  UINT8                       SerialIoSpiCsPolarity[14];

/** Offset 0x0188 - SPI<N> Chip Select Enable
  0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled
**/
  UINT8                       SerialIoSpiCsEnable[14];

/** Offset 0x0196 - SPIn Default Chip Select Output
  Sets Default CS as Output. N represents controller index: SPI0, SPI1, ... Available
  options: 0:CS0, 1:CS1
**/
  UINT8                       SerialIoSpiDefaultCsOutput[7];

/** Offset 0x019D - SPIn Default Chip Select Mode HW/SW
  Sets Default CS Mode Hardware or Software. N represents controller index: SPI0,
  SPI1, ... Available options: 0:HW, 1:SW
**/
  UINT8                       SerialIoSpiCsMode[7];

/** Offset 0x01A4 - SPIn Default Chip Select State Low/High
  Sets Default CS State Low or High. N represents controller index: SPI0, SPI1, ...
  Available options: 0:Low, 1:High
**/
  UINT8                       SerialIoSpiCsState[7];

/** Offset 0x01AB - SPIn Master Input Slave Output Enable/Disable
  0:Disabled, 1:Enabled. Sets Native Mode for SPIx MISO GPIO if it is Enabled
**/
  UINT8                       SerialIoSpiMisoEnable[3];

/** Offset 0x01AE - SPIn Delayed Rx Clock setting
  00:As-is, 01:Internal, 10:NegEdge Tx Clock, 11:NegEdge Delayed Rx Clk. Configure
  Delayed Rx Clock
**/
  UINT8                       SerialIoSpiDelayRxClk[3];

/** Offset 0x01B1 - UARTn Device Mode
  Selects Uart operation mode. N represents controller index: Uart0, Uart1, ... Available
  modes: 0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
  4:SerialIoUartSkipInit
**/
  UINT8                       SerialIoUartMode[7];

/** Offset 0x01B8 - Default BaudRate for each Serial IO UART
  Set default BaudRate Supported from 0 - default to 6000000
**/
  UINT32                      SerialIoUartBaudRate[7];

/** Offset 0x01D4 - Default ParityType for each Serial IO UART
  Set default Parity. 0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity
**/
  UINT8                       SerialIoUartParity[7];

/** Offset 0x01DB - Default DataBits for each Serial IO UART
  Set default word length. 0: Default, 5,6,7,8
**/
  UINT8                       SerialIoUartDataBits[7];

/** Offset 0x01E2 - Default StopBits for each Serial IO UART
  Set default stop bits. 0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3:
  TwoStopBits
**/
  UINT8                       SerialIoUartStopBits[7];

/** Offset 0x01E9 - Power Gating mode for each Serial IO UART that works in COM mode
  Set Power Gating. 0: Disabled, 1: Enabled, 2: Auto
**/
  UINT8                       SerialIoUartPowerGating[7];

/** Offset 0x01F0 - Enable Dma for each Serial IO UART that supports it
  Set DMA/PIO mode. 0: Disabled, 1: Enabled
**/
  UINT8                       SerialIoUartDmaEnable[7];

/** Offset 0x01F7 - Enables UART hardware flow control, CTS and RTS lines
  Enables UART hardware flow control, CTS and RTS lines.
**/
  UINT8                       SerialIoUartAutoFlow[7];

/** Offset 0x01FE
**/
  UINT8                       UnusedUpdSpace14[2];

/** Offset 0x0200 - SerialIoUartRtsPinMuxPolicy
  Select SerialIo Uart Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS*
  for possible values.
**/
  UINT32                      SerialIoUartRtsPinMuxPolicy[7];

/** Offset 0x021C - SerialIoUartCtsPinMuxPolicy
  Select SerialIo Uart Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS*
  for possible values.
**/
  UINT32                      SerialIoUartCtsPinMuxPolicy[7];

/** Offset 0x0238 - SerialIoUartRxPinMuxPolicy
  Select SerialIo Uart Rx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RX* for
  possible values.
**/
  UINT32                      SerialIoUartRxPinMuxPolicy[7];

/** Offset 0x0254 - SerialIoUartTxPinMuxPolicy
  Select SerialIo Uart Tx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_TX* for
  possible values.
**/
  UINT32                      SerialIoUartTxPinMuxPolicy[7];

/** Offset 0x0270 - UART Number For Debug Purpose
  UART number for debug purpose. 0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5,
  6:UART6. Note: If UART0 is selected as CNVi BT Core interface, it cannot be used
  for debug purpose.
   0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5, 6:UART6
**/
  UINT8                       SerialIoDebugUartNumber;

/** Offset 0x0271 - Serial IO UART DBG2 table
  Enable or disable Serial Io UART DBG2 table, default is Disable; <b>0: Disable;</b>
  1: Enable.
**/
  UINT8                       SerialIoUartDbg2[7];

/** Offset 0x0278 - I2Cn Device Mode
  Selects I2c operation mode. N represents controller index: I2c0, I2c1, ... Available
  modes: 0:SerialIoI2cDisabled, 1:SerialIoI2cPci, 2:SerialIoI2cHidden
**/
  UINT8                       SerialIoI2cMode[8];

/** Offset 0x0280 - Serial IO I2C SDA Pin Muxing
  Select SerialIo I2c Sda pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SDA* for
  possible values.
**/
  UINT32                      PchSerialIoI2cSdaPinMux[8];

/** Offset 0x02A0 - Serial IO I2C SCL Pin Muxing
  Select SerialIo I2c Scl pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SCL* for
  possible values.
**/
  UINT32                      PchSerialIoI2cSclPinMux[8];

/** Offset 0x02C0 - PCH SerialIo I2C Pads Termination
  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
  0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C0,I2C1,... pads termination
  respectively. One byte for each controller, byte0 for I2C0, byte1 for I2C1, and so on.
  0x1:None, 0x13:1kOhm WPU, 0x15:5kOhm WPU, 0x19:20kOhm WPU
**/
  UINT8                       PchSerialIoI2cPadsTermination[8];

/** Offset 0x02C8 - USB Per Port HS Preemphasis Bias
  USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
  100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port.
**/
  UINT8                       Usb2PhyPetxiset[16];

/** Offset 0x02D8 - USB Per Port HS Transmitter Bias
  USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
  100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port.
**/
  UINT8                       Usb2PhyTxiset[16];

/** Offset 0x02E8 - USB Per Port HS Transmitter Emphasis
  USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON,
  10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port.
**/
  UINT8                       Usb2PhyPredeemp[16];

/** Offset 0x02F8 - USB Per Port Half Bit Pre-emphasis
  USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis.
  One byte for each port.
**/
  UINT8                       Usb2PhyPehalfbit[16];

/** Offset 0x0308 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment
  Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value
  in arrary can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxDeEmphEnable[10];

/** Offset 0x0312 - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting
  USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16],
  <b>Default = 29h</b> (approximately -3.5dB De-Emphasis). One byte for each port.
**/
  UINT8                       Usb3HsioTxDeEmph[10];

/** Offset 0x031C - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment
  Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value
  in arrary can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxDownscaleAmpEnable[10];

/** Offset 0x0326 - USB 3.0 TX Output Downscale Amplitude Adjustment
  USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], <b>Default
  = 00h</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxDownscaleAmp[10];

/** Offset 0x0330
**/
  UINT8                       PchUsb3HsioCtrlAdaptOffsetCfgEnable[10];

/** Offset 0x033A
**/
  UINT8                       PchUsb3HsioFilterSelNEnable[10];

/** Offset 0x0344
**/
  UINT8                       PchUsb3HsioFilterSelPEnable[10];

/** Offset 0x034E
**/
  UINT8                       PchUsb3HsioOlfpsCfgPullUpDwnResEnable[10];

/** Offset 0x0358
**/
  UINT8                       PchUsb3HsioCtrlAdaptOffsetCfg[10];

/** Offset 0x0362
**/
  UINT8                       PchUsb3HsioOlfpsCfgPullUpDwnRes[10];

/** Offset 0x036C
**/
  UINT8                       PchUsb3HsioFilterSelN[10];

/** Offset 0x0376
**/
  UINT8                       PchUsb3HsioFilterSelP[10];

/** Offset 0x0380 - Enable LAN
  Enable/disable LAN controller.
  $EN_DIS
**/
  UINT8                       PchLanEnable;

/** Offset 0x0381 - Enable PCH TSN
  Enable/disable TSN on the PCH.
  $EN_DIS
**/
  UINT8                       PchTsnEnable;

/** Offset 0x0382 - PCH TSN Multi VC Enable
  Enable/Disable PCH TSN GBE Multiple Virtual Channel
  $EN_DIS
**/
  UINT8                       PchTsnGbeMultiVcEnable;

/** Offset 0x0383 - PCH TSN Link Speed
  Set PCH TSN Link Speed.
  0: 24Mhz 2.5Gbps, 1: 24Mhz 1Gbps, 2: 38.4Mhz 2.5Gbps, 3: 38.4Mhz 1Gbps
**/
  UINT8                       PchTsnGbeLinkSpeed;

/** Offset 0x0384 - PCH TSN SGMII Support
  Enable/disable SGMII support
  $EN_DIS
**/
  UINT8                       PchTsnGbeSgmiiEnable;

/** Offset 0x0385 - PSE TSN Multi VC Enable
  Enable/Disable PSE TSN GBE Multiple Virtual Channel
  $EN_DIS
**/
  UINT8                       PseTsnGbeMultiVcEnable[2];

/** Offset 0x0387 - PSE TSN Link Speed
  Set TSN Link Speed.
  0: 24Mhz 2.5Gbps, 1: 24Mhz 1Gbps, 2: 38.4Mhz 2.5Gbps, 3: 38.4Mhz 1Gbps
**/
  UINT8                       PseTsnGbeLinkSpeed[2];

/** Offset 0x0389 - PSE TSN SGMII Support
  Enable/disable SGMII support
  $EN_DIS
**/
  UINT8                       PseTsnGbeSgmiiEnable[2];

/** Offset 0x038B - PSE TSN Phy Interface Type
  Set PSE TSN Phy Interface Type
  0: Not Connected, 1: RGMII, 2: SGMII, 3:SGMII+
**/
  UINT8                       PseTsnGbePhyInterfaceType[2];

/** Offset 0x038D
**/
  UINT8                       UnusedUpdSpace15[3];

/** Offset 0x0390 - Tsn Mac Address Sub Region Base
  Base address of TSN MAC Address Sub Region
**/
  UINT32                      TsnMacAddrBase;

/** Offset 0x0394 - Tsn Mac Address Sub Region Size
  Size of TSN MAC Address Sub Region
**/
  UINT32                      TsnMacAddrSize;

/** Offset 0x0398 - PSE Tsn Ip Config Sub Region Base
  Base address of PSE TSN IP Config Sub Region
**/
  UINT32                      PseTsnIpConfigBase;

/** Offset 0x039C - PSE Tsn Ip Config Sub Region Size
  Size of PSE TSN IP Config Sub Region
**/
  UINT32                      PseTsnIpConfigSize;

/** Offset 0x03A0 - Tsn Config Sub Region Base
  Base address of TSN Config Sub Region
**/
  UINT32                      TsnConfigBase;

/** Offset 0x03A4 - Tsn Config Sub Region Size
  Size of TSN Config Sub Region
**/
  UINT32                      TsnConfigSize;

/** Offset 0x03A8 - PSE GBE0 DLL OVERRIDE
  Enable/Disable PSE GBE DLL OVERRIDE
  $EN_DIS
**/
  UINT8                       PseGbeDllOverride[2];

/** Offset 0x03AA - PSE GBE TX_Delay
  PSE GBE TX_Delay configuration.
**/
  UINT8                       PseGbeTxDelay[2];

/** Offset 0x03AC - PCIe PTM enable/disable
  Enable/disable Precision Time Measurement for PCIE Root Ports.
**/
  UINT8                       PciePtm[24];

/** Offset 0x03C4 - PCIe DPC enable/disable
  Enable/disable Downstream Port Containment for PCIE Root Ports.
**/
  UINT8                       PcieDpc[24];

/** Offset 0x03DC - PCIe DPC extensions enable/disable
  Enable/disable Downstream Port Containment Extensions for PCIE Root Ports.
**/
  UINT8                       PcieEdpc[24];

/** Offset 0x03F4 - USB PDO Programming
  Enable/disable PDO programming for USB in PEI phase. Disabling will allow for programming
  during later phase. 1: enable, 0: disable
  $EN_DIS
**/
  UINT8                       UsbPdoProgramming;

/** Offset 0x03F5
**/
  UINT8                       UnusedUpdSpace16[3];

/** Offset 0x03F8 - Power button debounce configuration
  Debounce time for PWRBTN in microseconds. For values not supported by HW, they will
  be rounded down to closest supported on. 0: disable, 250-1024000us: supported range
**/
  UINT32                      PmcPowerButtonDebounce;

/** Offset 0x03FC - PCH eSPI Master and Slave BME enabled
  PCH eSPI Master and Slave BME enabled
  $EN_DIS
**/
  UINT8                       PchEspiBmeMasterSlaveEnabled;

/** Offset 0x03FD - PCH SATA use RST Legacy OROM
  Use PCH SATA RST Legacy OROM when CSM is Enabled
  $EN_DIS
**/
  UINT8                       SataRstLegacyOrom;

/** Offset 0x03FE - Mask to enable the usage of external V1p05 VR rail in specific S0ix or Sx states
  Enable External V1P05 Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5
**/
  UINT8                       PchFivrExtV1p05RailEnabledStates;

/** Offset 0x03FF - Mask to enable the platform configuration of external V1p05 VR rail
  External V1P05 Rail Supported Configuration
**/
  UINT8                       PchFivrExtV1p05RailSupportedVoltageStates;

/** Offset 0x0400 - External V1P05 Voltage Value that will be used in S0i2/S0i3 states
  Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...)
**/
  UINT16                      PchFivrExtV1p05RailVoltage;

/** Offset 0x0402 - External V1P05 Icc Max Value
  Granularity of this setting is 1mA and maximal possible value is 200mA
**/
  UINT8                       PchFivrExtV1p05RailIccMax;

/** Offset 0x0403 - Mask to enable the usage of external Vnn VR rail in specific S0ix or Sx states
  Enable External Vnn Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5
**/
  UINT8                       PchFivrExtVnnRailEnabledStates;

/** Offset 0x0404 - Mask to enable the platform configuration of external Vnn VR rail
  External Vnn Rail Supported Configuration
**/
  UINT8                       PchFivrExtVnnRailSupportedVoltageStates;

/** Offset 0x0405
**/
  UINT8                       UnusedUpdSpace17;

/** Offset 0x0406 - External Vnn Voltage Value that will be used in S0ix/Sx states
  Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...), Default is set to 420
**/
  UINT16                      PchFivrExtVnnRailVoltage;

/** Offset 0x0408 - External Vnn Icc Max Value that will be used in S0ix/Sx states
  Granularity of this setting is 1mA and maximal possible value is 200mA
**/
  UINT8                       PchFivrExtVnnRailIccMax;

/** Offset 0x0409 - Mask to enable the usage of external Vnn VR rail in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Enable External Vnn Rail in
  Sx: BIT0-1:Reserved, BIT2:S3, BIT3:S4, BIT5:S5
**/
  UINT8                       PchFivrExtVnnRailSxEnabledStates;

/** Offset 0x040A - External Vnn Voltage Value that will be used in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Value is given in 2.5mV increments
  (0=0mV, 1=2.5mV, 2=5mV...)
**/
  UINT16                      PchFivrExtVnnRailSxVoltage;

/** Offset 0x040C - External Vnn Icc Max Value that will be used in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting
  is 1mA and maximal possible value is 200mA
**/
  UINT8                       PchFivrExtVnnRailSxIccMax;

/** Offset 0x040D - Transition time in microseconds from Low Current Mode Voltage to High Current Mode Voltage
  This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
  to low current mode voltage.
**/
  UINT8                       PchFivrVccinAuxLowToHighCurModeVolTranTime;

/** Offset 0x040E - Transition time in microseconds from Retention Mode Voltage to High Current Mode Voltage
  This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
  to retention mode voltage.
**/
  UINT8                       PchFivrVccinAuxRetToHighCurModeVolTranTime;

/** Offset 0x040F - Transition time in microseconds from Retention Mode Voltage to Low Current Mode Voltage
  This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
  to retention mode voltage.
**/
  UINT8                       PchFivrVccinAuxRetToLowCurModeVolTranTime;

/** Offset 0x0410 - Transition time in microseconds from Off (0V) to High Current Mode Voltage
  This field has 1us resolution. When value is 0 Transition to 0V is disabled.
**/
  UINT16                      PchFivrVccinAuxOffToHighCurModeVolTranTime;

/** Offset 0x0412
**/
  UINT8                       UnusedUpdSpace18[2];

/** Offset 0x0414 - Trace Hub Memory Base
  If Trace Hub is enabled and trace to memory is desired, BootLoader needs to allocate
  trace hub memory as reserved and uncacheable, set the base to ensure Trace Hub
  memory is configured properly.
**/
  UINT32                      TraceHubMemBase;

/** Offset 0x0418 - PMC Debug Message Enable
  When Enabled, PMC HW will send debug messages to trace hub; When Disabled, PMC HW
  will never send debug meesages to trace hub. Noted: When Enabled, may not enter S0ix
  $EN_DIS
**/
  UINT8                       PmcDbgMsgEn;

/** Offset 0x0419
**/
  UINT8                       UnusedUpdSpace19[3];

/** Offset 0x041C - Pointer of ChipsetInit Binary
  ChipsetInit Binary Pointer.
**/
  UINT32                      ChipsetInitBinPtr;

/** Offset 0x0420 - Length of ChipsetInit Binary
  ChipsetInit Binary Length.
**/
  UINT32                      ChipsetInitBinLen;

/** Offset 0x0424 - ChipsetInit Sync Enable
  Enable/Disable. 0: Disable, 1: Enable
**/
  UINT8                       ChipsetInitSyncEnable;

/** Offset 0x0425 - FIVR Dynamic Power Management
  Enable/Disable FIVR Dynamic Power Management.
  $EN_DIS
**/
  UINT8                       PchFivrDynPm;

/** Offset 0x0426 - External V1P05 Icc Max Value
  Granularity of this setting is 1mA and maximal possible value is 500mA
**/
  UINT16                      PchFivrExtV1p05RailIccMaximum;

/** Offset 0x0428 - External Vnn Icc Max Value that will be used in S0ix/Sx states
  Granularity of this setting is 1mA and maximal possible value is 500mA
**/
  UINT16                      PchFivrExtVnnRailIccMaximum;

/** Offset 0x042A - External Vnn Icc Max Value that will be used in Sx states
  Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting
  is 1mA and maximal possible value is 500mA
**/
  UINT16                      PchFivrExtVnnRailSxIccMaximum;

/** Offset 0x042C - PCH eSPI Link Configuration Lock (SBLCL)
  Enable/Disable lock of communication through SET_CONFIG/GET_CONFIG to eSPI slaves
  addresseses from range 0x0 - 0x7FF
  $EN_DIS
**/
  UINT8                       PchEspiLockLinkConfiguration;

/** Offset 0x042D - Extented BIOS Direct Read Decode enable
  Enable/Disable access to bigger than 16MB BIOS Region through Direct Memory Reads.
  0: disabled (default), 1: enabled
  $EN_DIS
**/
  UINT8                       PchSpiExtendedBiosDecodeRangeEnable;

/** Offset 0x042E - PchPostMemRsvd
  Reserved for PCH Post-Mem
  $EN_DIS
**/
  UINT8                       PchPostMemRsvd[11];

/** Offset 0x0439
**/
  UINT8                       UnusedUpdSpace20[3];

/** Offset 0x043C - Extended BIOS Direct Read Decode Range base
  Bits of 31:16 of a memory address that'll be a base for Extended BIOS Direct Read Decode.
**/
  UINT32                      PchSpiExtendedBiosDecodeRangeBase;

/** Offset 0x0440 - Extended BIOS Direct Read Decode Range limit
  Bits of 31:16 of a memory address that'll be a limit for Extended BIOS Direct Read Decode.
**/
  UINT32                      PchSpiExtendedBiosDecodeRangeLimit;

/** Offset 0x0444 - CNVi Configuration
  This option allows for automatic detection of Connectivity Solution. [Auto Detection]
  assumes that CNVi will be enabled when available, [Disable] allows for disabling CNVi.
  0:Disable, 1:Auto
**/
  UINT8                       CnviMode;

/** Offset 0x0445 - CNVi BT Core
  Enable/Disable CNVi BT Core, Default is ENABLE. 0: DISABLE, 1: ENABLE
  $EN_DIS
**/
  UINT8                       CnviBtCore;

/** Offset 0x0446 - CNVi BT Audio Offload
  Enable/Disable BT Audio Offload, Default is DISABLE. 0: DISABLE, 1: ENABLE
  $EN_DIS
**/
  UINT8                       CnviBtAudioOffload;

/** Offset 0x0447
**/
  UINT8                       UnusedUpdSpace21;

/** Offset 0x0448 - CNVi RF_RESET pin muxing
  Select CNVi RF_RESET# pin depending on board routing. TGP-LP: GPP_A8 = 0x2942E408(default)
  or GPP_F4 = 0x194BE404. TGP-H: 0. TGP-K: 0. Refer to GPIO_*_MUXING_CNVI_RF_RESET_*
  in GpioPins*.h.
**/
  UINT32                      CnviRfResetPinMux;

/** Offset 0x044C - CNVi CLKREQ pin muxing
  Select CNVi CLKREQ pin depending on board routing. TGP-LP: GPP_A9 = 0x3942E609(default)
  or GPP_F5 = 0x394BE605. TGP-H: 0. TGP-K: 0. Refer to GPIO_*_MUXING_CNVI_MODEM_CLKREQ_*
  in GpioPins*.h.
**/
  UINT32                      CnviClkreqPinMux;

/** Offset 0x0450 - Enable Host C10 reporting through eSPI
  Enable/disable Host C10 reporting to Slave via eSPI Virtual Wire.
  $EN_DIS
**/
  UINT8                       PchEspiHostC10ReportEnable;

/** Offset 0x0451 - PCH USB2 PHY Power Gating enable
  1: Will enable USB2 PHY SUS Well Power Gating, 0: Will not enable PG of USB2 PHY
  Sus Well PG
  $EN_DIS
**/
  UINT8                       PmcUsb2PhySusPgEnable;

/** Offset 0x0452 - PCH USB OverCurrent mapping enable
  1: Will program USB OC pin mapping in xHCI controller memory, 0: Will clear OC pin
  mapping allow for NOA usage of OC pins
  $EN_DIS
**/
  UINT8                       PchUsbOverCurrentEnable;

/** Offset 0x0453 - Espi Lgmr Memory Range decode
  This option enables or disables espi lgmr
  $EN_DIS
**/
  UINT8                       PchEspiLgmrEnable;

/** Offset 0x0454 - External V1P05 Control Ramp Timer value
  Hold off time to be used when changing the v1p05_ctrl for external bypass value in us
**/
  UINT8                       PchFivrExtV1p05RailCtrlRampTmr;

/** Offset 0x0455 - External VNN Control Ramp Timer value
  Hold off time to be used when changing the vnn_ctrl for external bypass value in us
**/
  UINT8                       PchFivrExtVnnRailCtrlRampTmr;

/** Offset 0x0456 - HECI3 state
  The HECI3 state from Mbp for reference in S3 path or when MbpHob is not installed.
  0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       Heci3Enabled;

/** Offset 0x0457 - PCHHOT# pin
  Enable PCHHOT# pin assertion when temperature is higher than PchHotLevel. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       PchHotEnable;

/** Offset 0x0458 - SATA LED
  SATA LED indicating SATA controller activity. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       SataLedEnable;

/** Offset 0x0459 - VRAlert# Pin
  When VRAlert# feature pin is enabled and its state is '0', the PMC requests throttling
  to a T3 Tstate to the PCH throttling unit.. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       PchPmVrAlert;

/** Offset 0x045A - AMT Switch
  Enable/Disable. 0: Disable, 1: enable, Enable or disable AMT functionality.
  $EN_DIS
**/
  UINT8                       AmtEnabled;

/** Offset 0x045B - WatchDog Timer Switch
  Enable/Disable. 0: Disable, 1: enable, Enable or disable WatchDog timer. Setting
  is invalid if AmtEnabled is 0.
  $EN_DIS
**/
  UINT8                       WatchDogEnabled;

/** Offset 0x045C - Manageability Mode set by Mebx
  Enable/Disable. 0: Disable, 1: enable, Enable or disable Manageability Mode.
  $EN_DIS
**/
  UINT8                       ManageabilityMode;

/** Offset 0x045D - PET Progress
  Enable/Disable. 0: Disable, 1: enable, Enable/Disable PET Events Progress to receive
  PET Events. Setting is invalid if AmtEnabled is 0.
  $EN_DIS
**/
  UINT8                       FwProgress;

/** Offset 0x045E - SOL Switch
  Enable/Disable. 0: Disable, 1: enable, Serial Over Lan enable/disable state by Mebx.
  Setting is invalid if AmtEnabled is 0.
  $EN_DIS
**/
  UINT8                       AmtSolEnabled;

/** Offset 0x045F
**/
  UINT8                       UnusedUpdSpace22;

/** Offset 0x0460 - OS Timer
  16 bits Value, Set OS watchdog timer. Setting is invalid if AmtEnabled is 0.
**/
  UINT16                      WatchDogTimerOs;

/** Offset 0x0462 - BIOS Timer
  16 bits Value, Set BIOS watchdog timer. Setting is invalid if AmtEnabled is 0.
**/
  UINT16                      WatchDogTimerBios;

/** Offset 0x0464 - Remote Assistance Trigger Availablilty
  Enable/Disable. 0: Disable, 1: enable, Remote Assistance enable/disable state by Mebx.
  $EN_DIS
**/
  UINT8                       RemoteAssistance;

/** Offset 0x0465 - KVM Switch
  Enable/Disable. 0: Disable, 1: enable, KVM enable/disable state by Mebx. Setting
  is invalid if AmtEnabled is 0.
  $EN_DIS
**/
  UINT8                       AmtKvmEnabled;

/** Offset 0x0466 - KVM Switch
  Enable/Disable. 0: Disable, 1: enable, KVM enable/disable state by Mebx.
  $EN_DIS
**/
  UINT8                       ForcMebxSyncUp;

/** Offset 0x0467 - PCH PCIe root port connection type
  0: built-in device, 1:slot
**/
  UINT8                       PcieRpSlotImplemented[24];

/** Offset 0x047F - PCIE RP Access Control Services Extended Capability
  Enable/Disable PCIE RP Access Control Services Extended Capability
**/
  UINT8                       PcieRpAcsEnabled[24];

/** Offset 0x0497 - PCIE RP Clock Power Management
  Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal
  can still be controlled by L1 PM substates mechanism
**/
  UINT8                       PcieRpEnableCpm[24];

/** Offset 0x04AF - PCIE RP Multi VC Enabled
  Enable/Disable PCIE RP Multiple Virtual Channels
**/
  UINT8                       PcieRpMultiVcEnabled[24];

/** Offset 0x04C7 - PCIE RP VC1 to TC Mapping
  PCIE RP Virtual Channel 1 to Traffic Class mapping
**/
  UINT8                       PcieRpVc1TcMap[24];

/** Offset 0x04DF
**/
  UINT8                       UnusedUpdSpace23[1];

/** Offset 0x04E0 - PCIE RP Detect Timeout Ms
  The number of milliseconds within 0~65535 in reference code will wait for link to
  exit Detect state for enabled ports before assuming there is no device and potentially
  disabling the port.
**/
  UINT16                      PcieRpDetectTimeoutMs[24];

/** Offset 0x0510 - ModPHY SUS Power Domain Dynamic Gating
  Enable/Disable ModPHY SUS Power Domain Dynamic Gating. Setting not supported on
  PCH-H. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       PmcModPhySusPgEnable;

/** Offset 0x0511 - V1p05-PHY supply external FET control
  Enable/Disable control using EXT_PWR_GATE# pin of external FET to power gate v1p05-PHY
  supply. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       PmcV1p05PhyExtFetControlEn;

/** Offset 0x0512 - V1p05-IS supply external FET control
  Enable/Disable control using EXT_PWR_GATE2# pin of external FET to power gate v1p05-IS
  supply. 0: disable, 1: enable
  $EN_DIS
**/
  UINT8                       PmcV1p05IsExtFetControlEn;

/** Offset 0x0513 - Enable/Disable PavpEnable
  Enable(Default): Enable PavpEnable, Disable: Disable PavpEnable
  $EN_DIS
**/
  UINT8                       PavpEnable;

/** Offset 0x0514 - CdClock Frequency selection
  0 (Default) Auto (Max based on reference clock frequency), 0: 307.2, 1: 312 Mhz,
  2: 552 Mhz, 3: 556.8 Mhz, 4: 648 Mhz, 5: 652.8 Mhz
  0xFF: Auto (Max based on reference clock frequency), 0: 307.2, 1: 312 Mhz, 2: 552
  Mhz, 3: 556.8 Mhz, 4: 648 Mhz, 5: 652.8 Mhz
**/
  UINT8                       CdClock;

/** Offset 0x0515 - Enable/Disable PeiGraphicsPeimInit
  Enable(Default): Enable PeiGraphicsPeimInit, Disable: Disable PeiGraphicsPeimInit
  $EN_DIS
**/
  UINT8                       PeiGraphicsPeimInit;

/** Offset 0x0516 - Enable D3 Hot in TCSS
  This policy will enable/disable D3 hot support in IOM
  $EN_DIS
**/
  UINT8                       D3HotEnable;

/** Offset 0x0517 - Enable or disable GNA device
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       GnaEnable;

/** Offset 0x0518 - Enable or disable HPD of DDI port-A device
  0=Disabled,1(Default)=eDP, 2=MIPI DSI,
  0:Disabled, 1:eDP, 2:MIPI DSI
**/
  UINT8                       DdiPortAConfig;

/** Offset 0x0519 - Enable or disable HPD of DDI port-B device
  1(Default)=DP, 2=MIPI DSI, 3=HDMI
  1:DP, 2:MIPI DSI, 3:HDMI
**/
  UINT8                       DdiPortBConfig;

/** Offset 0x051A - Enable or disable HPD of DDI port-C device
  1(Default)= HDMI, 2=DP
  1:HDMI, 2:DP
**/
  UINT8                       DdiPortCConfig;

/** Offset 0x051B - Enable or disable HPD of DDI port A
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPortAHpd;

/** Offset 0x051C - Enable or disable HPD of DDI port B
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPortBHpd;

/** Offset 0x051D - Enable or disable HPD of DDI port C
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPortCHpd;

/** Offset 0x051E - Enable or disable HPD of DDI port 1
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPort1Hpd;

/** Offset 0x051F - Enable or disable HPD of DDI port 2
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPort2Hpd;

/** Offset 0x0520 - Enable or disable HPD of DDI port 3
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPort3Hpd;

/** Offset 0x0521 - Enable or disable HPD of DDI port 4
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPort4Hpd;

/** Offset 0x0522 - Enable or disable DDC of DDI port A
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPortADdc;

/** Offset 0x0523 - Enable or disable DDC of DDI port B
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPortBDdc;

/** Offset 0x0524 - Enable or disable DDC of DDI port C
  0=Disable, 1(Default)=Enable
  $EN_DIS
**/
  UINT8                       DdiPortCDdc;

/** Offset 0x0525 - Enable DDC setting of DDI Port 1
  0=Disable, 1=DDC(Default)
  0: Disable, 1: DDC
**/
  UINT8                       DdiPort1Ddc;

/** Offset 0x0526 - Enable DDC setting of DDI Port 2
  0=Disable, 1=DDC(Default)
  0: Disable, 1: DDC
**/
  UINT8                       DdiPort2Ddc;

/** Offset 0x0527 - Enable DDC setting of DDI Port 3
  0=Disable, 1=DDC(Default)
  0: Disable, 1: DDC
**/
  UINT8                       DdiPort3Ddc;

/** Offset 0x0528 - Enable DDC setting of DDI Port 4
  0=Disable, 1=DDC(Default)
  0: Disable, 1: DDC
**/
  UINT8                       DdiPort4Ddc;

/** Offset 0x0529
**/
  UINT8                       UnusedUpdSpace24[3];

/** Offset 0x052C - TypeC port GPIO setting
  GPIO Ping number for Type C Aux Oritation setting, use the GpioPad that is defined
  in GpioPinsXXXH.h and GpioPinsXXXLp.h as argument.(XXX is platform name, Ex: Ehl
  = ElkhartLake)
**/
  UINT32                      IomTypeCPortPadCfg[8];

/** Offset 0x054C - CPU USB3 Port Over Current Pin
  Describe the specific over current pin number of USBC Port N.
**/
  UINT8                       CpuUsb3OverCurrentPin[8];

/** Offset 0x0554 - Enable D3 Cold in TCSS
  This policy will enable/disable D3 cold support in IOM
  $EN_DIS
**/
  UINT8                       D3ColdEnable;

/** Offset 0x0555 - PchPostMemRsvd
  Reserved for PCH Post-Mem
  $EN_DIS
**/
  UINT8                       SaPostMemRsvd[8];

/** Offset 0x055D - Enable VMD controller
  Enable/disable to VMD controller.0: Disable(Default); 1: Enable
  $EN_DIS
**/
  UINT8                       VmdEnable;

/** Offset 0x055E - Enable VMD portA Support
  Enable/disable to VMD portA Support.
  $EN_DIS
**/
  UINT8                       VmdPortA;

/** Offset 0x055F - Enable VMD portB Support
  Enable/disable to VMD portB Support.
  $EN_DIS
**/
  UINT8                       VmdPortB;

/** Offset 0x0560 - Enable VMD portC Support
  Enable/disable to VMD portC Support.
  $EN_DIS
**/
  UINT8                       VmdPortC;

/** Offset 0x0561 - Enable VMD portD Support
  Enable/disable to VMD portD Support.
  $EN_DIS
**/
  UINT8                       VmdPortD;

/** Offset 0x0562 - VMD Config Bar size
  Set The VMD Config Bar Size.
**/
  UINT8                       VmdCfgBarSz;

/** Offset 0x0563 - VMD Config Bar Attributes
  0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH(Default)
  0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
**/
  UINT8                       VmdCfgBarAttr;

/** Offset 0x0564 - VMD Mem Bar1 size
  Set The VMD Mem Bar1 Size.
**/
  UINT8                       VmdMemBarSz1;

/** Offset 0x0565 - VMD Mem Bar1 Attributes
  0: VMD_32BIT_NONPREFETCH(Default), 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
  0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
**/
  UINT8                       VmdMemBar1Attr;

/** Offset 0x0566 - VMD Mem Bar2 size
  Set The VMD Mem Bar2 Size.
**/
  UINT8                       VmdMemBarSz2;

/** Offset 0x0567 - VMD Mem Bar2 Attributes
  0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH(Default), 2: VMD_64BIT_PREFETCH
  0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
**/
  UINT8                       VmdMemBar2Attr;

/** Offset 0x0568 - Enable/Disable PMC-PD Solution
  This policy will enable/disable PMC-PD Solution vs EC-TCPC Solution
  $EN_DIS
**/
  UINT8                       PmcPdEnable;

/** Offset 0x0569
**/
  UINT8                       UnusedUpdSpace25;

/** Offset 0x056A - TCSS Aux Orientation Override Enable
  Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides
**/
  UINT16                      TcssAuxOri;

/** Offset 0x056C - TCSS HSL Orientation Override Enable
  Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides
**/
  UINT16                      TcssHslOri;

/** Offset 0x056E - USB override in IOM
  This policy will enable/disable USB Connect override in IOM
  $EN_DIS
**/
  UINT8                       UsbOverride;

/** Offset 0x056F - TCSS USB Port Enable
  Bits 0, 1, ... max Type C port control enables
**/
  UINT8                       UsbTcPortEn;

/** Offset 0x0570 - ITBT Root Port Enable
  ITBT Root Port Enable, 0:Disable, 1:Enable
  0:Disable, 1:Enable
**/
  UINT8                       ITbtPcieRootPortEn[4];

/** Offset 0x0574 - ITBTForcePowerOn Timeout value
  ITBTForcePowerOn value. Specified increment values in miliseconds. Range is 0-1000.
  100 = 100 ms.
**/
  UINT16                      ITbtForcePowerOnTimeoutInMs;

/** Offset 0x0576 - ITbtConnectTopology Timeout value
  ITbtConnectTopologyTimeout value. Specified increment values in miliseconds. Range
  is 0-10000. 100 = 100 ms.
**/
  UINT16                      ITbtConnectTopologyTimeoutInMs;

/** Offset 0x0578 - VCCST request for IOM
  This policy will enable/disable VCCST and also decides if message would be replayed in S4/S5
  $EN_DIS
**/
  UINT8                       VccSt;

/** Offset 0x0579
**/
  UINT8                       UnusedUpdSpace26[1];

/** Offset 0x057A - ITBT DMA LTR
  TCSS DMA1, DMA2 LTR value
**/
  UINT16                      ITbtDmaLtr[2];

/** Offset 0x057E - Enable/Disable CrashLog
  Enable(Default): Enable CPU CrashLog, Disable: Disable CPU CrashLog
  $EN_DIS
**/
  UINT8                       CpuCrashLogEnable;

/** Offset 0x057F - Enable/Disable PTM
  This policy will enable/disable Precision Time Measurement for TCSS PCIe Root Ports
  $EN_DIS
**/
  UINT8                       PtmEnabled[4];

/** Offset 0x0583 - PCIE RP Ltr Enable
  Latency Tolerance Reporting Mechanism.
**/
  UINT8                       SaPcieItbtRpLtrEnable[4];

/** Offset 0x0587 - PCIE RP Snoop Latency Override Mode
  Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
  UINT8                       SaPcieItbtRpSnoopLatencyOverrideMode[4];

/** Offset 0x058B - PCIE RP Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
  UINT8                       SaPcieItbtRpSnoopLatencyOverrideMultiplier[4];

/** Offset 0x058F
**/
  UINT8                       UnusedUpdSpace27[1];

/** Offset 0x0590 - PCIE RP Snoop Latency Override Value
  Latency Tolerance Reporting, Snoop Latency Override Value.
**/
  UINT16                      SaPcieItbtRpSnoopLatencyOverrideValue[4];

/** Offset 0x0598 - PCIE RP Non Snoop Latency Override Mode
  Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
  UINT8                       SaPcieItbtRpNonSnoopLatencyOverrideMode[4];

/** Offset 0x059C - PCIE RP Non Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
  UINT8                       SaPcieItbtRpNonSnoopLatencyOverrideMultiplier[4];

/** Offset 0x05A0 - PCIE RP Non Snoop Latency Override Value
  Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
  UINT16                      SaPcieItbtRpNonSnoopLatencyOverrideValue[4];

/** Offset 0x05A8 - Force LTR Override
  Force LTR Override.
**/
  UINT8                       SaPcieItbtRpForceLtrOverride[4];

/** Offset 0x05AC - PCIE RP Ltr Config Lock
  0: Disable; 1: Enable.
**/
  UINT8                       SaPcieItbtRpLtrConfigLock[4];

/** Offset 0x05B0 - Advanced Encryption Standard (AES) feature
  Enable or Disable Advanced Encryption Standard (AES) feature; </b>0: Disable; <b>1: Enable
  $EN_DIS
**/
  UINT8                       AesEnable;

/** Offset 0x05B1 - Power State 3 enable/disable
  PCODE MMIO Mailbox: Power State 3 enable/disable; 0: Disable; <b>1: Enable</b>.
  For all VR Indexes
**/
  UINT8                       Psi3Enable[5];

/** Offset 0x05B6 - Power State 4 enable/disable
  PCODE MMIO Mailbox: Power State 4 enable/disable; 0: Disable; <b>1: Enable</b>.For
  all VR Indexes
**/
  UINT8                       Psi4Enable[5];

/** Offset 0x05BB
**/
  UINT8                       UnusedUpdSpace28[1];

/** Offset 0x05BC - Imon slope correction
  PCODE MMIO Mailbox: Imon slope correction. Specified in 1/100 increment values.
  Range is 0-200. 125 = 1.25. <b>0: Auto</b>.For all VR Indexes
**/
  UINT16                      ImonSlope[5];

/** Offset 0x05C6 - Imon offset correction
  PCODE MMIO Mailbox: Imon offset correction. Value is a 2's complement signed integer.
  Units 1/1000, Range 0-63999. For an offset = 12.580, use 12580. <b>0: Auto</b>
**/
  UINT16                      ImonOffset[5];

/** Offset 0x05D0 - Enable/Disable BIOS configuration of VR
  Enable/Disable BIOS configuration of VR; <b>0: Disable</b>; 1: Enable.For all VR Indexes
**/
  UINT8                       VrConfigEnable[5];

/** Offset 0x05D5 - Thermal Design Current enable/disable
  PCODE MMIO Mailbox: Thermal Design Current enable/disable; <b>0: Disable</b>; 1:
  Enable.For all VR Indexes
**/
  UINT8                       TdcEnable[5];

/** Offset 0x05DA
**/
  UINT8                       UnusedUpdSpace29[2];

/** Offset 0x05DC - Thermal Design Current time window
  PCODE MMIO Mailbox: Thermal Design Current time window. Defined in milli seconds.
  Range 1ms to 448s
**/
  UINT32                      TdcTimeWindow[5];

/** Offset 0x05F0 - Thermal Design Current Lock
  PCODE MMIO Mailbox: Thermal Design Current Lock; <b>0: Disable</b>; 1: Enable.For
  all VR Indexes
**/
  UINT8                       TdcLock[5];

/** Offset 0x05F5 - Platform Psys slope correction
  PCODE MMIO Mailbox: Platform Psys slope correction. <b>0 - Auto</b> Specified in
  1/100 increment values. Range is 0-200. 125 = 1.25
**/
  UINT8                       PsysSlope;

/** Offset 0x05F6 - Platform Psys offset correction
  PCODE MMIO Mailbox: Platform Psys offset correction. <b>0 - Auto</b> Units 1/1000,
  Range 0-63999. For an offset of 25.348, enter 25348.
**/
  UINT16                      PsysOffset;

/** Offset 0x05F8 - Acoustic Noise Mitigation feature
  Enable or Disable Acoustic Noise Mitigation feature. <b>0: Disabled</b>; 1: Enabled
  $EN_DIS
**/
  UINT8                       AcousticNoiseMitigation;

/** Offset 0x05F9 - Disable Fast Slew Rate for Deep Package C States for VR domains
  Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
  feature enabled. <b>0: False</b>; 1: True
  $EN_DIS
**/
  UINT8                       FastPkgCRampDisable[5];

/** Offset 0x05FE - Slew Rate configuration for Deep Package C States for VR domains
  Slew Rate configuration for Deep Package C States for VR domains based on Acoustic
  Noise Mitigation feature enabled. <b>0: Fast/2</b>; 1: Fast/4; 2: Fast/8; 3: Fast/16
  0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
  UINT8                       SlowSlewRate[5];

/** Offset 0x0603
**/
  UINT8                       UnusedUpdSpace30[1];

/** Offset 0x0604 - Thermal Design Current current limit
  PCODE MMIO Mailbox: Thermal Design Current current limit. Specified in 1/8A units.
  Range is 0-4095. 1000 = 125A. <b>0: Auto</b>. For all VR Indexes
**/
  UINT16                      TdcCurrentLimit[5];

/** Offset 0x060E - AcLoadline
  PCODE MMIO Mailbox: AcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is
  0-6249. <b>Intel Recommended Defaults vary by domain and SKU.
**/
  UINT16                      AcLoadline[5];

/** Offset 0x0618 - DcLoadline
  PCODE MMIO Mailbox: DcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is
  0-6249.<b>Intel Recommended Defaults vary by domain and SKU.</b>
**/
  UINT16                      DcLoadline[5];

/** Offset 0x0622 - Power State 1 Threshold current
  PCODE MMIO Mailbox: Power State 1 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
  UINT16                      Psi1Threshold[5];

/** Offset 0x062C - Power State 2 Threshold current
  PCODE MMIO Mailbox: Power State 2 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
  UINT16                      Psi2Threshold[5];

/** Offset 0x0636 - Power State 3 Threshold current
  PCODE MMIO Mailbox: Power State 3 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
  UINT16                      Psi3Threshold[5];

/** Offset 0x0640 - Icc Max limit
  PCODE MMIO Mailbox: VR Icc Max limit. 0-255A in 1/4 A units. 400 = 100A
**/
  UINT16                      IccMax[5];

/** Offset 0x064A - Enable VR specific mailbox command
  VR specific mailbox commands. <b>00b - no VR specific command sent.</b>  01b - A
  VR mailbox command specifically for the MPS IMPV8 VR will be sent. 10b - VR specific
  command sent for PS4 exit issue. 11b - Reserved.
  $EN_DIS
**/
  UINT8                       SendVrMbxCmd;

/** Offset 0x064B - Enable or Disable TXT
  Enable or Disable TXT; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       TxtEnable;

/** Offset 0x064C - Skip Multi-Processor Initialization
  When this is skipped, boot loader must initialize processors before SilicionInit
  API. </b>0: Initialize; <b>1: Skip
  $EN_DIS
**/
  UINT8                       SkipMpInit;

/** Offset 0x064D
**/
  UINT8                       UnusedUpdSpace31;

/** Offset 0x064E - FIVR RFI Frequency
  PCODE MMIO Mailbox: Set the desired RFI frequency, in increments of 100KHz. <b>0:
  Auto</b>. Range varies based on XTAL clock: 0-1918 (Up to 191.8HMz) for 24MHz clock;
  0-1535 (Up to 153.5MHz) for 19MHz clock.
**/
  UINT16                      FivrRfiFrequency;

/** Offset 0x0650 - FIVR RFI Spread Spectrum
  PCODE MMIO Mailbox: FIVR RFI Spread Spectrum, in 0.1% increments. <b>0: 0%</b>;
  Range: 0.0% to 10.0% (0-100).
**/
  UINT8                       FivrSpreadSpectrum;

/** Offset 0x0651
**/
  UINT8                       UnusedUpdSpace32[3];

/** Offset 0x0654 -  UFS Soft Strap Start Address
   UFS Soft Strap Start Address, Value will be based on the CSE IFWI Layout
**/
  UINT32                      UfsStrapAddress;

/** Offset 0x0658 - CpuBistData
  Pointer CPU BIST Data
**/
  UINT32                      CpuBistData;

/** Offset 0x065C - CpuMpPpi
  <b>Optional</b> pointer to the boot loader's implementation of EFI_PEI_MP_SERVICES_PPI.
  If not NULL, FSP will use the boot loader's implementation of multiprocessing.
  See section 5.1.4 of the FSP Integration Guide for more details.
**/
  UINT32                      CpuMpPpi;

/** Offset 0x0660 - CpuMpHob
  <b>Optional</b> pointer for CpuMpHob. If the boot loader is a UEFI boot loader using
  API mode instead of dispatch mode, and FspsUpd->FspsConfig.CpuMpPpi != NULL, then
  FspsUpd->FspsConfig.CpuMpHob must be != NULL. See section 5.1.4 of the FSP Integration
  Guide for more details.
**/
  UINT32                      CpuMpHob;

/** Offset 0x0664
**/
  UINT8                       CpuPostMemRsvd[16];

/** Offset 0x0674 - PpinSupport to view Protected Processor Inventory Number
  Enable or Disable or Auto (Based on End of Manufacturing flag. Disabled if this
  flag is set) for PPIN Support
  0: Disable, 1: Enable, 2: Auto
**/
  UINT8                       PpinSupport;

/** Offset 0x0675 - Enable or Disable Minimum Voltage Override
  Enable or disable Minimum Voltage overrides ; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       EnableMinVoltageOverride;

/** Offset 0x0676 - Min Voltage for Runtime
  PCODE MMIO Mailbox: Minimum voltage for runtime. Valid if EnableMinVoltageOverride
  = 1. Range 0 to 1999mV. <b> 0: 0mV </b>
**/
  UINT16                      MinVoltageRuntime;

/** Offset 0x0678 - Base of memory region allocated for Processor Trace
  Base address of memory region allocated for Processor Trace. Processor Trace requires
  2^N alignment and size in bytes per thread, from 4KB to 128MB. <b>0: Disable</b>
**/
  UINT64                      ProcessorTraceMemBase;

/** Offset 0x0680 - Memory region allocation for Processor Trace
  Length in bytes of memory region allocated for Processor Trace. Processor Trace
  requires 2^N alignment and size in bytes per thread, from 4KB to 128MB. <b>0: Disable</b>
**/
  UINT32                      ProcessorTraceMemLength;

/** Offset 0x0684 - Min Voltage for C8
  PCODE MMIO Mailbox: Minimum voltage for C8. Valid if EnableMinVoltageOverride =
  1. Range 0 to 1999mV. <b> 0: 0mV </b>
**/
  UINT16                      MinVoltageC8;

/** Offset 0x0686 - Smbios Type4 Max Speed Override
  Provide the option for platform to override the MaxSpeed field of Smbios Type 4.
  If this value is not zero, it dominates the field.
**/
  UINT16                      SmbiosType4MaxSpeedOverride;

/** Offset 0x0688 - ReservedCpuPostMemProduction
  Reserved for CPU Post-Mem Production
  $EN_DIS
**/
  UINT8                       ReservedCpuPostMemProduction[6];

/** Offset 0x068E - AC Split Lock
  Enable/Disable #AC check on split lock. <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       AcSplitLock;

/** Offset 0x068F - PCH Master Clock Gating Control
  Provide a master control for clock gating for all PCH devices, 0: Disabled; 1: Default
  $EN_DIS
**/
  UINT8                       PchMasterClockGating;

/** Offset 0x0690 - PCH Master Power Gating Control
  Provide a master control for pwoer gating for all PCH devices, 0: Disabled; 1: Default
  $EN_DIS
**/
  UINT8                       PchMasterPowerGating;

/** Offset 0x0691 - Sci Pin Mux Enable
  Enable/Disable Sci Gpio Pin Mux. <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       SciPinMuxEnable;

/** Offset 0x0692 - Enable Power Optimizer
  Enable DMI Power Optimizer on PCH side.
  $EN_DIS
**/
  UINT8                       PchPwrOptEnable;

/** Offset 0x0693 - PCH Flash Protection Ranges Write Enble
  Write or erase is blocked by hardware.
**/
  UINT8                       PchWriteProtectionEnable[5];

/** Offset 0x0698 - PCH Flash Protection Ranges Read Enble
  Read is blocked by hardware.
**/
  UINT8                       PchReadProtectionEnable[5];

/** Offset 0x069D
**/
  UINT8                       UnusedUpdSpace33[1];

/** Offset 0x069E - PCH Protect Range Limit
  Left shifted address by 12 bits with address bits 11:0 are assumed to be FFFh for
  limit comparison.
**/
  UINT16                      PchProtectedRangeLimit[5];

/** Offset 0x06A8 - PCH Protect Range Base
  Left shifted address by 12 bits with address bits 11:0 are assumed to be 0.
**/
  UINT16                      PchProtectedRangeBase[5];

/** Offset 0x06B2 - Enable Pme
  Enable Azalia wake-on-ring.
  $EN_DIS
**/
  UINT8                       PchHdaPme;

/** Offset 0x06B3 - HD Audio Link Frequency
  HDA Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 0: 6MHz, 1: 12MHz, 2: 24MHz.
  0: 6MHz, 1: 12MHz, 2: 24MHz
**/
  UINT8                       PchHdaLinkFrequency;

/** Offset 0x06B4 - PchPostMemRsvd
  Reserved for PCH Post-Mem
  $EN_DIS
**/
  UINT8                       PchPostMemRsvd4[3];

/** Offset 0x06B7 - Enable PCH Io Apic Entry 24-119
  0: Disable; 1: Enable.
  $EN_DIS
**/
  UINT8                       PchIoApicEntry24_119;

/** Offset 0x06B8 - PCH Io Apic ID
  This member determines IOAPIC ID. Default is 0x02.
**/
  UINT8                       PchIoApicId;

/** Offset 0x06B9
**/
  UINT8                       UnusedUpdSpace34[3];

/** Offset 0x06BC - PCH PSE Log Output Channel
  Set PSE Log Output Channel. 0: internal memory; 1-6: UART channels; Other: shut down
**/
  UINT32                      PchPseLogOutputChannel;

/** Offset 0x06C0 - PCH PSE Log Output Size
  Set PSE Log Output Size
**/
  UINT16                      PchPseLogOutputSize;

/** Offset 0x06C2 - PCH PSE Log Output Offset
  Set PSE Log Output Offset
**/
  UINT16                      PchPseLogOutputOffset;

/** Offset 0x06C4 - PCH PSE OOB Prov State Offset
  Set PSE OOB Prov State Offset
**/
  UINT16                      PchPseOobProvDone;

/** Offset 0x06C6 - Enable PCH PSE I2S pins assigned
  Set if PSE I2S native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseI2sEnable[2];

/** Offset 0x06C8 - PchPseI2sTxPinMux
  Select PSE I2S Tx pin muxing. Refer to GPIO_*_MUXING_PSE_I2Sx_TXD* for possible values.
**/
  UINT32                      PchPseI2sTxPinMux[2];

/** Offset 0x06D0 - PchPseI2sRxPinMux
  Select PSE I2S Rx pin muxing. Refer to GPIO_*_MUXING_PSE_I2Sx_RXD* for possible values.
**/
  UINT32                      PchPseI2sRxPinMux[2];

/** Offset 0x06D8 - PchPseI2sSfrmPinMux
  Select PSE I2S Sfrm pin muxing. Refer to GPIO_*_MUXING_PSE_I2Sx_SFRM* for possible values.
**/
  UINT32                      PchPseI2sSfrmPinMux[2];

/** Offset 0x06E0 - PchPseI2sSclkPinMux
  Select PSE I2S Sclk pin muxing. Refer to GPIO_*_MUXING_PSE_I2Sx_SCLK* for possible values.
**/
  UINT32                      PchPseI2sSclkPinMux[2];

/** Offset 0x06E8 - Enable PCH PSE PWM pins assigned
  Set if PSE PWM native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPsePwmEnable;

/** Offset 0x06E9 - PchPsePwmPinEnable
  Set PWM pin to PSE PWM native function. 0: Disable; 1: Enable.
**/
  UINT8                       PchPsePwmPinEnable[16];

/** Offset 0x06F9
**/
  UINT8                       UnusedUpdSpace35[3];

/** Offset 0x06FC - PchPsePwmPinMux
  Select PSE Pwm pin muxing start from PWM0 to PWM15. Refer to GPIO_*_MUXING_PSE_PWM*
  for possible values.
**/
  UINT32                      PchPsePwmPinMux[16];

/** Offset 0x073C - Enable PCH PSE UART pins assigned
  Set if PSE UART native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseUartEnable[6];

/** Offset 0x0742 - Enable PCH PSE HSUART pins assigned
  Set if PSE HSUART native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseHsuartEnable[4];

/** Offset 0x0746 - Enable PCH PSE QEP pins assigned
  Set if PSE QEP native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseQepEnable[4];

/** Offset 0x074A - Enable PCH PSE DMA pins assigned
  Set if PSE DMA native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseDmaEnable[3];

/** Offset 0x074D - Enable PCH PSE GBE pins assigned
  Set if PSE GBE native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseGbeEnable[2];

/** Offset 0x074F - Enable PCH PSE I2C pins assigned
  Set if PSE I2C native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseI2cEnable[8];

/** Offset 0x0757 - Enable PCH PSE SPI pins assigned
  Set if PSE SPI native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseSpiEnable[4];

/** Offset 0x075B - Enable PCH PSE SPI CS0 pins assigned
  Set if PSE SPI CS0 pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseSpiCs0Enable[4];

/** Offset 0x075F - Enable PCH PSE SPI CS1 pins assigned
  Set if PSE SPI CS1 pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseSpiCs1Enable[4];

/** Offset 0x0763
**/
  UINT8                       UnusedUpdSpace36[1];

/** Offset 0x0764 - PchPseSpiMosiPinMux
  Select PSE Spi Mosi pin muxing. Refer to GPIO_*_MUXING_PSE_SPIx_MOSI* for possible values.
**/
  UINT32                      PchPseSpiMosiPinMux[4];

/** Offset 0x0774 - PchPseSpiMisoPinMux
  Select PSE Spi Miso pin muxing. Refer to GPIO_*_MUXING_PSE_SPIx_MISO* for possible values.
**/
  UINT32                      PchPseSpiMisoPinMux[4];

/** Offset 0x0784 - PchPseSpiClkPinMux
  Select PSE Spi Clk pin muxing. Refer to GPIO_*_MUXING_PSE_SPIx_SCLK* for possible values.
**/
  UINT32                      PchPseSpiClkPinMux[4];

/** Offset 0x0794 - PchPseSpiCs0PinMux
  Select PSE Spi Cs pin muxing. Refer to GPIO_*_MUXING_PSE_SPIx_Cs* for possible values.
**/
  UINT32                      PchPseSpiCs0PinMux[4];

/** Offset 0x07A4 - PchPseSpiCs1PinMux
  Select PSE Spi Cs pin muxing. Refer to GPIO_*_MUXING_PSE_SPIx_Cs* for possible values.
**/
  UINT32                      PchPseSpiCs1PinMux[4];

/** Offset 0x07B4 - Enable PCH PSE ADC pins assigned
  Set if PSE ADC native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseAdcEnable;

/** Offset 0x07B5 - Enable PCH PSE CAN pins assigned
  Set if PSE CAN native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseCanEnable[2];

/** Offset 0x07B7 - Enable PCH PSE I2S sideband interrupt
  Set if PSE I2S are to be set to sideband interrupt. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseI2sSbInterruptEnable[2];

/** Offset 0x07B9 - Enable PCH PSE PWM sideband interrupt
  Set if PSE PWM are to be set to sideband interrupt. 0: Disable; 1: Enable.
**/
  UINT8                       PchPsePwmSbInterruptEnable;

/** Offset 0x07BA - Enable PCH PSE UART sideband interrupt
  Set if PSE UART are to be set to sideband interrupt. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseUartSbInterruptEnable[6];

/** Offset 0x07C0 - Enable PCH PSE QEP sideband interrupt
  Set if PSE QEP are to be set to sideband interrupt. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseQepSbInterruptEnable[4];

/** Offset 0x07C4 - Enable PCH PSE DMA sideband interrupt
  Set if PSE DMA are to be set to sideband interrupt. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseDmaSbInterruptEnable[3];

/** Offset 0x07C7 - Enable PCH PSE I2C sideband interrupt
  Set if PSE I2C are to be set to sideband interrupt. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseI2cSbInterruptEnable[8];

/** Offset 0x07CF - Enable PCH PSE SPI sideband interrupt
  Set if PSE SPI are to be set to sideband interrupt. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseSpiSbInterruptEnable[4];

/** Offset 0x07D3 - Enable PCH PSE ADC sideband interrupt
  Set if PSE ADC are to be set to sideband interrupt. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseAdcSbInterruptEnable;

/** Offset 0x07D4 - Enable PCH PSE LH2OSE sideband interrupt
  Set if PSE LH2OSE are to be set to sideband interrupt. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseLh2PseSbInterruptEnable;

/** Offset 0x07D5 - Enable PCH PSE CAN sideband interrupt
  Set if PSE CAN are to be set to sideband interrupt. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseCanSbInterruptEnable[2];

/** Offset 0x07D7 - Enable PCH PSE Timed GPIO pins assigned
  Set if PSE Timed GPIO native pins and ownership are to be enabled by BIOS. 0: Disable/pins
  are not owned by PSE/host; 1: Pins are muxed to PSE IP, the IO is owned by PSE;
  2: Pins are muxed to PSE IP, the IO is owned by host;
**/
  UINT8                       PchPseTimedGpioEnable[2];

/** Offset 0x07D9 - Enable PCH PSE Timed GPIO 20 pins allocation
  Allocate 20 pins for PCH PSE Timed GPIO. 0: Top 20 pins; 1: Mid 20 pins; 2: Lower 20 pins.
**/
  UINT8                       PchPseTimedGpioPinAllocation[2];

/** Offset 0x07DB - Enable PCH PSE Timed GPIO Pin to PSE TGPIO native function
  Set TGPIO pin to PSE TGPIO native function. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseTimedGpioPinEnable[60];

/** Offset 0x0817
**/
  UINT8                       UnusedUpdSpace37;

/** Offset 0x0818 - Pch Pse Tgpio6 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio6PinMux;

/** Offset 0x081C - Pch Pse Tgpio7 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio7PinMux;

/** Offset 0x0820 - Pch Pse Tgpio8 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio8PinMux;

/** Offset 0x0824 - Pch Pse Tgpio9 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio9PinMux;

/** Offset 0x0828 - Pch Pse Tgpio10 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio10PinMux;

/** Offset 0x082C - Pch Pse Tgpio11 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio11PinMux;

/** Offset 0x0830 - Pch Pse Tgpio12 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio12PinMux;

/** Offset 0x0834 - Pch Pse Tgpio13 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio13PinMux;

/** Offset 0x0838 - Pch Pse Tgpio14 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio14PinMux;

/** Offset 0x083C - Pch Pse Tgpio15 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio15PinMux;

/** Offset 0x0840 - Pch Pse Tgpio16 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio16PinMux;

/** Offset 0x0844 - Pch Pse Tgpio17 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio17PinMux;

/** Offset 0x0848 - Pch Pse Tgpio18 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio18PinMux;

/** Offset 0x084C - Pch Pse Tgpio19 Pin Mux
  Select PSE Timed Gpio pin muxing. Refer to GPIO_*_MUXING_PSE_TGPIO* for possible values.
**/
  UINT32                      PchPseTgpio19PinMux;

/** Offset 0x0850 - Enable PCH Lan LTR capabilty of PCH internal LAN
  0: Disable; 1: Enable.
  $EN_DIS
**/
  UINT8                       PchLanLtrEnable;

/** Offset 0x0851 - Enable LOCKDOWN BIOS LOCK
  Enable the BIOS Lock feature and set EISS bit (D31:F5:RegDCh[5]) for the BIOS region
  protection.
  $EN_DIS
**/
  UINT8                       PchLockDownBiosLock;

/** Offset 0x0852 - PCH Compatibility Revision ID
  This member describes whether or not the CRID feature of PCH should be enabled.
  $EN_DIS
**/
  UINT8                       PchCrid;

/** Offset 0x0853 - RTC BIOS Interface Lock
  Enable RTC BIOS interface lock. When set, prevents RTC TS (BUC.TS) from being changed.
  $EN_DIS
**/
  UINT8                       RtcBiosInterfaceLock;

/** Offset 0x0854 - RTC Cmos Memory Lock
  Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper
  and and lower 128-byte bank of RTC RAM.
  $EN_DIS
**/
  UINT8                       RtcMemoryLock;

/** Offset 0x0855 - Enable PCIE RP HotPlug
  Indicate whether the root port is hot plug available.
**/
  UINT8                       PcieRpHotPlug[24];

/** Offset 0x086D - Enable PCIE RP Pm Sci
  Indicate whether the root port power manager SCI is enabled.
**/
  UINT8                       PcieRpPmSci[24];

/** Offset 0x0885 - Enable PCIE RP Transmitter Half Swing
  Indicate whether the Transmitter Half Swing is enabled.
**/
  UINT8                       PcieRpTransmitterHalfSwing[24];

/** Offset 0x089D - Enable PCIE RP Clk Req Detect
  Probe CLKREQ# signal before enabling CLKREQ# based power management.
**/
  UINT8                       PcieRpClkReqDetect[24];

/** Offset 0x08B5 - PCIE RP Advanced Error Report
  Indicate whether the Advanced Error Reporting is enabled.
**/
  UINT8                       PcieRpAdvancedErrorReporting[24];

/** Offset 0x08CD - PCIE RP Unsupported Request Report
  Indicate whether the Unsupported Request Report is enabled.
**/
  UINT8                       PcieRpUnsupportedRequestReport[24];

/** Offset 0x08E5 - PCIE RP Fatal Error Report
  Indicate whether the Fatal Error Report is enabled.
**/
  UINT8                       PcieRpFatalErrorReport[24];

/** Offset 0x08FD - PCIE RP No Fatal Error Report
  Indicate whether the No Fatal Error Report is enabled.
**/
  UINT8                       PcieRpNoFatalErrorReport[24];

/** Offset 0x0915 - PCIE RP Correctable Error Report
  Indicate whether the Correctable Error Report is enabled.
**/
  UINT8                       PcieRpCorrectableErrorReport[24];

/** Offset 0x092D - PCIE RP System Error On Fatal Error
  Indicate whether the System Error on Fatal Error is enabled.
**/
  UINT8                       PcieRpSystemErrorOnFatalError[24];

/** Offset 0x0945 - PCIE RP System Error On Non Fatal Error
  Indicate whether the System Error on Non Fatal Error is enabled.
**/
  UINT8                       PcieRpSystemErrorOnNonFatalError[24];

/** Offset 0x095D - PCIE RP System Error On Correctable Error
  Indicate whether the System Error on Correctable Error is enabled.
**/
  UINT8                       PcieRpSystemErrorOnCorrectableError[24];

/** Offset 0x0975 - PCIE RP Max Payload
  Max Payload Size supported, Default 128B, see enum PCH_PCIE_MAX_PAYLOAD.
**/
  UINT8                       PcieRpMaxPayload[24];

/** Offset 0x098D - Touch Host Controller Port 0 Assignment
  Assign THC Port 0
  0x0:ThcAssignmentNone, 0x1:ThcAssignmentThc0
**/
  UINT8                       ThcPort0Assignment;

/** Offset 0x098E
**/
  UINT8                       UnusedUpdSpace38[2];

/** Offset 0x0990 - THC Port 0 Interrupt Pin Mux
  Set THC Port 0 Pin Muxing Value if signal can be enabled on multiple pads. Refer
  to GPIO_*_MUXING_THC_SPIx_INTB_* for possible values.
**/
  UINT32                      ThcPort0InterruptPinMuxing;

/** Offset 0x0994 - Touch Host Controller Port 1 Assignment
  Assign THC Port 1
  0x0:ThcAssignmentNone, 0x1:ThcPort1AssignmentThc0, 0x2:ThcAssignmentThc1
**/
  UINT8                       ThcPort1Assignment;

/** Offset 0x0995 - Touch Host Controller Port 1 ReadFrequency
  Set THC Port 1 Read Frequency (THC_PORT_FREQUENCY enum): 0:2p1MHz,1:2p5Mz,2:3Mz,3:3p75Mz,4:5MHz,5:7p5MHz,6:15MHz,7:17MHz,8:20MHz,9:24MHz,10:30MHz
  0:2p1MHz,1:2p5Mz,2:3Mz,3:3p75Mz,4:5MHz,5:7p5MHz,6:15MHz,7:17MHz,8:20MHz,9:24MHz,10:30MHz
**/
  UINT8                       ThcPort1ReadFrequency;

/** Offset 0x0996 - Touch Host Controller Port 1 WriteFrequency
  Set THC Port 1 Write Frequency (THC_PORT_FREQUENCY enum): 0:2p1MHz,1:2p5Mz,2:3Mz,3:3p75Mz,4:5MHz,5:7p5MHz,6:15MHz,7:17MHz,8:20MHz,9:24MHz,10:30MHz
  0:2p1MHz,1:2p5Mz,2:3Mz,3:3p75Mz,4:5MHz,5:7p5MHz,6:15MHz,7:17MHz,8:20MHz,9:24MHz,10:30MHz
**/
  UINT8                       ThcPort1WriteFrequency;

/** Offset 0x0997
**/
  UINT8                       UnusedUpdSpace39;

/** Offset 0x0998 - THC Port 1 Interrupt Pin Mux
  Set THC Port 1 Pin Muxing Value if signal can be enabled on multiple pads. Refer
  to GPIO_*_MUXING_THC_SPIx_INTB_* for possible values.
**/
  UINT32                      ThcPort1InterruptPinMuxing;

/** Offset 0x099C - PCIE RP Pcie Speed
  Determines each PCIE Port speed capability. 0: Auto; 1: Gen1; 2: Gen2; 3: Gen3 (see:
  PCH_PCIE_SPEED).
**/
  UINT8                       PcieRpPcieSpeed[24];

/** Offset 0x09B4 - PCIE RP Physical Slot Number
  Indicates the slot number for the root port. Default is the value as root port index.
**/
  UINT8                       PcieRpPhysicalSlotNumber[24];

/** Offset 0x09CC - PCIE RP Completion Timeout
  The root port completion timeout(see: PCH_PCIE_COMPLETION_TIMEOUT). Default is PchPcieCompletionTO_Default.
**/
  UINT8                       PcieRpCompletionTimeout[24];

/** Offset 0x09E4 - PCIE RP Aspm
  The ASPM configuration of the root port (see: PCH_PCIE_ASPM_CONTROL). Default is
  PchPcieAspmAutoConfig.
**/
  UINT8                       PcieRpAspm[24];

/** Offset 0x09FC - PCIE RP L1 Substates
  The L1 Substates configuration of the root port (see: PCH_PCIE_L1SUBSTATES_CONTROL).
  Default is PchPcieL1SubstatesL1_1_2.
**/
  UINT8                       PcieRpL1Substates[24];

/** Offset 0x0A14 - PCIE RP Ltr Enable
  Latency Tolerance Reporting Mechanism.
**/
  UINT8                       PcieRpLtrEnable[24];

/** Offset 0x0A2C - PCIE RP Ltr Config Lock
  0: Disable; 1: Enable.
**/
  UINT8                       PcieRpLtrConfigLock[24];

/** Offset 0x0A44 - PCIe override default settings for EQ
  Choose PCIe EQ method
  $EN_DIS
**/
  UINT8                       PcieEqOverrideDefault;

/** Offset 0x0A45 - PCIe choose EQ method
  Choose PCIe EQ method
  0: HardwareEq, 1: FixedEq
**/
  UINT8                       PcieEqMethod;

/** Offset 0x0A46 - PCIe choose EQ mode
  Choose PCIe EQ mode
  0: PresetEq, 1: CoefficientEq
**/
  UINT8                       PcieEqMode;

/** Offset 0x0A47 - PCIe EQ local transmitter override
  Enable/Disable local transmitter override
  $EN_DIS
**/
  UINT8                       PcieEqLocalTransmitterOverrideEnable;

/** Offset 0x0A48 - PCIe number of valid list entries
  Select number of presets or coefficients depending on the mode
**/
  UINT8                       PcieEqPh3NumberOfPresetsOrCoefficients;

/** Offset 0x0A49 - PCIe pre-cursor coefficient list
  Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
  UINT8                       PcieEqPh3PreCursorList[10];

/** Offset 0x0A53 - PCIe post-cursor coefficient list
  Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
  UINT8                       PcieEqPh3PostCursorList[10];

/** Offset 0x0A5D - PCIe preset list
  Provide a list of presets to be used during phase 3 EQ
**/
  UINT8                       PcieEqPh3PresetList[11];

/** Offset 0x0A68 - PCIe EQ phase 1 downstream transmitter port preset
  Allows to select the downstream port preset value that will be used during phase
  1 of equalization
**/
  UINT32                      PcieEqPh1DownstreamPortTransmitterPreset;

/** Offset 0x0A6C - PCIe EQ phase 1 upstream tranmitter port preset
  Allows to select the upstream port preset value that will be used during phase 1
  of equalization
**/
  UINT32                      PcieEqPh1UpstreamPortTransmitterPreset;

/** Offset 0x0A70 - PCIe EQ phase 2 local transmitter override preset
  Allows to select the value of the preset used during phase 2 local transmitter override
**/
  UINT8                       PcieEqPh2LocalTransmitterOverridePreset;

/** Offset 0x0A71 - PCIE Enable Peer Memory Write
  This member describes whether Peer Memory Writes are enabled on the platform.
  $EN_DIS
**/
  UINT8                       PcieEnablePeerMemoryWrite;

/** Offset 0x0A72 - PCIE Compliance Test Mode
  Compliance Test Mode shall be enabled when using Compliance Load Board.
  $EN_DIS
**/
  UINT8                       PcieComplianceTestMode;

/** Offset 0x0A73 - PCI Express Clock Gating
  Enable/Disable Clock Gating, 0: PLATFORM_POR, 1: FORCE_ENABLE, 2: FORCE_DISABLE.
  0: POR, 1: Force Enable, 2: Force Disable
**/
  UINT8                       TestPcieClockGating;

/** Offset 0x0A74 - PCIE Rp Function Swap
  Allows BIOS to use root port function number swapping when root port of function
  0 is disabled.
  $EN_DIS
**/
  UINT8                       PcieRpFunctionSwap;

/** Offset 0x0A75 - Enable/Disable PEG GEN3 Static EQ Phase1 programming
  Program Gen3 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static Presets
  Programming, Enabled(0x1)(Default): Enable  EQ Phase1 Static Presets Programming
  $EN_DIS
**/
  UINT8                       CpuPcieGen3ProgramStaticEq;

/** Offset 0x0A76 - Enable/Disable GEN4 Static EQ Phase1 programming
  Program Gen4 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static Presets
  Programming, Enabled(0x1)(Default): Enable  EQ Phase1 Static Presets Programming
  $EN_DIS
**/
  UINT8                       CpuPcieGen4ProgramStaticEq;

/** Offset 0x0A77 - PCH Pm PME_B0_S5_DIS
  When cleared (default), wake events from PME_B0_STS are allowed in S5 if PME_B0_EN = 1.
  $EN_DIS
**/
  UINT8                       PchPmPmeB0S5Dis;

/** Offset 0x0A78 - PCIE IMR
  Enables Isolated Memory Region for PCIe.
  $EN_DIS
**/
  UINT8                       PcieRpImrEnabled;

/** Offset 0x0A79 - PCIE IMR port number
  Selects PCIE root port number for IMR feature.
**/
  UINT8                       PcieRpImrSelection;

/** Offset 0x0A7A - PCH Pm Wol Enable Override
  Corresponds to the WOL Enable Override bit in the General PM Configuration B (GEN_PMCON_B) register.
  $EN_DIS
**/
  UINT8                       PchPmWolEnableOverride;

/** Offset 0x0A7B - PCH Pm Pcie Wake From DeepSx
  Determine if enable PCIe to wake from deep Sx.
  $EN_DIS
**/
  UINT8                       PchPmPcieWakeFromDeepSx;

/** Offset 0x0A7C - PCH Pm WoW lan Enable
  Determine if WLAN wake from Sx, corresponds to the HOST_WLAN_PP_EN bit in the PWRM_CFG3 register.
  $EN_DIS
**/
  UINT8                       PchPmWoWlanEnable;

/** Offset 0x0A7D - PCH Pm WoW lan DeepSx Enable
  Determine if WLAN wake from DeepSx, corresponds to the DSX_WLAN_PP_EN bit in the
  PWRM_CFG3 register.
  $EN_DIS
**/
  UINT8                       PchPmWoWlanDeepSxEnable;

/** Offset 0x0A7E - PCH Pm Lan Wake From DeepSx
  Determine if enable LAN to wake from deep Sx.
  $EN_DIS
**/
  UINT8                       PchPmLanWakeFromDeepSx;

/** Offset 0x0A7F - PCH Pm Deep Sx Pol
  Deep Sx Policy.
  $EN_DIS
**/
  UINT8                       PchPmDeepSxPol;

/** Offset 0x0A80 - PCH Pm Slp S3 Min Assert
  SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms.
**/
  UINT8                       PchPmSlpS3MinAssert;

/** Offset 0x0A81 - PCH Pm Slp S4 Min Assert
  SLP_S4 Minimum Assertion Width Policy. Default is PchSlpS44s.
**/
  UINT8                       PchPmSlpS4MinAssert;

/** Offset 0x0A82 - PCH Pm Slp Sus Min Assert
  SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s.
**/
  UINT8                       PchPmSlpSusMinAssert;

/** Offset 0x0A83 - PCH Pm Slp A Min Assert
  SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s.
**/
  UINT8                       PchPmSlpAMinAssert;

/** Offset 0x0A84 - USB Overcurrent Override for DbC
  This option overrides USB Over Current enablement state that USB OC will be disabled
  after enabling this option. Enable when DbC is used to avoid signaling conflicts.
  $EN_DIS
**/
  UINT8                       PchEnableDbcObs;

/** Offset 0x0A85 - PCH Pm Slp Strch Sus Up
  Enable SLP_X Stretching After SUS Well Power Up.
  $EN_DIS
**/
  UINT8                       PchPmSlpStrchSusUp;

/** Offset 0x0A86 - PCH Pm Slp Lan Low Dc
  Enable/Disable SLP_LAN# Low on DC Power.
  $EN_DIS
**/
  UINT8                       PchPmSlpLanLowDc;

/** Offset 0x0A87 - PCH Pm Pwr Btn Override Period
  PCH power button override period. 000b-4s, 001b-6s, 010b-8s, 011b-10s, 100b-12s, 101b-14s.
**/
  UINT8                       PchPmPwrBtnOverridePeriod;

/** Offset 0x0A88 - PCH Pm Disable Dsx Ac Present Pulldown
  When Disable, PCH will internal pull down AC_PRESENT in deep SX and during G3 exit.
  $EN_DIS
**/
  UINT8                       PchPmDisableDsxAcPresentPulldown;

/** Offset 0x0A89 - PCH Pm Disable Native Power Button
  Power button native mode disable.
  $EN_DIS
**/
  UINT8                       PchPmDisableNativePowerButton;

/** Offset 0x0A8A - PCH Pm ME_WAKE_STS
  Clear the ME_WAKE_STS bit in the Power and Reset Status (PRSTS) register.
  $EN_DIS
**/
  UINT8                       PchPmMeWakeSts;

/** Offset 0x0A8B - PCH Pm WOL_OVR_WK_STS
  Clear the WOL_OVR_WK_STS bit in the Power and Reset Status (PRSTS) register.
  $EN_DIS
**/
  UINT8                       PchPmWolOvrWkSts;

/** Offset 0x0A8C - PCH Pm Reset Power Cycle Duration
  Could be customized in the unit of second. Please refer to EDS for all support settings.
  0 is default, 1 is 1 second, 2 is 2 seconds, ...
**/
  UINT8                       PchPmPwrCycDur;

/** Offset 0x0A8D - PCH Pm Pcie Pll Ssc
  Specifies the Pcie Pll Spread Spectrum Percentage. The default is 0xFF: AUTO - No
  BIOS override.
**/
  UINT8                       PchPmPciePllSsc;

/** Offset 0x0A8E - PCH Legacy IO Low Latency Enable
  Set to enable low latency of legacy IO. <b>0: Disable</b>, 1: Enable
  $EN_DIS
**/
  UINT8                       PchLegacyIoLowLatency;

/** Offset 0x0A8F - PCH Sata Pwr Opt Enable
  SATA Power Optimizer on PCH side.
  $EN_DIS
**/
  UINT8                       SataPwrOptEnable;

/** Offset 0x0A90 - PCH Sata eSATA Speed Limit
  When enabled, BIOS will configure the PxSCTL.SPD to 2 to limit the eSATA port speed.
  $EN_DIS
**/
  UINT8                       EsataSpeedLimit;

/** Offset 0x0A91 - PCH Sata Speed Limit
  Indicates the maximum speed the SATA controller can support 0h: PchSataSpeedDefault.
**/
  UINT8                       SataSpeedLimit;

/** Offset 0x0A92 - Enable SATA Port HotPlug
  Enable SATA Port HotPlug.
**/
  UINT8                       SataPortsHotPlug[8];

/** Offset 0x0A9A - Enable SATA Port Interlock Sw
  Enable SATA Port Interlock Sw.
**/
  UINT8                       SataPortsInterlockSw[8];

/** Offset 0x0AA2 - Enable SATA Port External
  Enable SATA Port External.
**/
  UINT8                       SataPortsExternal[8];

/** Offset 0x0AAA - Enable SATA Port SpinUp
  Enable the COMRESET initialization Sequence to the device.
**/
  UINT8                       SataPortsSpinUp[8];

/** Offset 0x0AB2 - Enable SATA Port Solid State Drive
  0: HDD; 1: SSD.
**/
  UINT8                       SataPortsSolidStateDrive[8];

/** Offset 0x0ABA - Enable SATA Port Enable Dito Config
  Enable DEVSLP Idle Timeout settings (DmVal, DitoVal).
**/
  UINT8                       SataPortsEnableDitoConfig[8];

/** Offset 0x0AC2 - Enable SATA Port DmVal
  DITO multiplier. Default is 15.
**/
  UINT8                       SataPortsDmVal[8];

/** Offset 0x0ACA - Enable SATA Port DmVal
  DEVSLP Idle Timeout (DITO), Default is 625.
**/
  UINT16                      SataPortsDitoVal[8];

/** Offset 0x0ADA - Enable SATA Port ZpOdd
  Support zero power ODD.
**/
  UINT8                       SataPortsZpOdd[8];

/** Offset 0x0AE2 - Enable SATA Port RxPolarity
  Reverse RxPolarity.
**/
  UINT8                       SataPortsRxPolarity[8];

/** Offset 0x0AEA - PCH Sata Rst Raid Alternate Id
  Enable RAID Alternate ID.
  $EN_DIS
**/
  UINT8                       SataRstRaidDeviceId;

/** Offset 0x0AEB - PCH Sata Rst Raid0
  RAID0.
  $EN_DIS
**/
  UINT8                       SataRstRaid0;

/** Offset 0x0AEC - PCH Sata Rst Raid1
  RAID1.
  $EN_DIS
**/
  UINT8                       SataRstRaid1;

/** Offset 0x0AED - PCH Sata Rst Raid10
  RAID10.
  $EN_DIS
**/
  UINT8                       SataRstRaid10;

/** Offset 0x0AEE - PCH Sata Rst Raid5
  RAID5.
  $EN_DIS
**/
  UINT8                       SataRstRaid5;

/** Offset 0x0AEF - PCH Sata Rst Irrt
  Intel Rapid Recovery Technology.
  $EN_DIS
**/
  UINT8                       SataRstIrrt;

/** Offset 0x0AF0 - PCH Sata Rst Orom Ui Banner
  OROM UI and BANNER.
  $EN_DIS
**/
  UINT8                       SataRstOromUiBanner;

/** Offset 0x0AF1 - PCH Sata Rst Orom Ui Delay
  00b: 2 secs; 01b: 4 secs; 10b: 6 secs; 11: 8 secs (see: PCH_SATA_OROM_DELAY).
**/
  UINT8                       SataRstOromUiDelay;

/** Offset 0x0AF2 - PCH Sata Rst Hdd Unlock
  Indicates that the HDD password unlock in the OS is enabled.
  $EN_DIS
**/
  UINT8                       SataRstHddUnlock;

/** Offset 0x0AF3 - PCH Sata Rst Led Locate
  Indicates that the LED/SGPIO hardware is attached and ping to locate feature is
  enabled on the OS.
  $EN_DIS
**/
  UINT8                       SataRstLedLocate;

/** Offset 0x0AF4 - PCH Sata Rst Irrt Only
  Allow only IRRT drives to span internal and external ports.
  $EN_DIS
**/
  UINT8                       SataRstIrrtOnly;

/** Offset 0x0AF5 - PCH Sata Rst Smart Storage
  RST Smart Storage caching Bit.
  $EN_DIS
**/
  UINT8                       SataRstSmartStorage;

/** Offset 0x0AF6 - PCH Sata Rst Pcie Storage Remap enable
  Enable Intel RST for PCIe Storage remapping.
**/
  UINT8                       SataRstPcieEnable[3];

/** Offset 0x0AF9 - PCH Sata Rst Pcie Storage Port
  Intel RST for PCIe Storage remapping - PCIe Port Selection (1-based, 0 = autodetect).
**/
  UINT8                       SataRstPcieStoragePort[3];

/** Offset 0x0AFC - PCH Sata Rst Pcie Device Reset Delay
  PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms
**/
  UINT8                       SataRstPcieDeviceResetDelay[3];

/** Offset 0x0AFF - UFS enable/disable
  PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms
  $EN_DIS
**/
  UINT8                       UfsEnable[2];

/** Offset 0x0B01 - IEH Mode
  Integrated Error Handler Mode, 0: Bypass, 1: Enable
  0: Bypass, 1:Enable
**/
  UINT8                       IehMode;

/** Offset 0x0B02 - PSF Tcc
  Psf Tcc (Time Coordinated Computing) Enable will decrease psf transaction latency
  by disable some psf power management features, 0: Disable, 1: Enable
  $EN_DIS
**/
  UINT8                       PsfTccEnable;

/** Offset 0x0B03 - TCC Mode Default Flag
  Variable to determine TCC mode default value, 0: Disable, 1: Enable
  $EN_DIS
**/
  UINT8                       TccModeInitFlag;

/** Offset 0x0B04 - Tcc Tuning enable/disable
  Tcc (Time Coordinated Computing) Tuning Enabled
  $EN_DIS
**/
  UINT8                       TccTuningEnable;

/** Offset 0x0B05
**/
  UINT8                       UnusedUpdSpace40[3];

/** Offset 0x0B08 - Tcc Register File Base Address
  Tcc (Time Coordinated Computing) Register File Base Address
**/
  UINT32                      TccConfigBase;

/** Offset 0x0B0C - Tcc Register File Size
  Tcc (Time Coordinated Computing) Register File Size
**/
  UINT32                      TccConfigSize;

/** Offset 0x0B10 - Fusa Display Configuration
  Fusa (Functional Safety) Enable Fusa Feature on Display, 0: Disable, 1: Enable
  $EN_DIS
**/
  UINT8                       DisplayFusaConfigEnable;

/** Offset 0x0B11 - Fusa Graphics Configuration
  Fusa (Functional Safety) Enable Fusa Feature on Graphics, 0: Disable, 1: Enable
  $EN_DIS
**/
  UINT8                       GraphicFusaConfigEnable;

/** Offset 0x0B12 - Fusa Opio Configuration
  Fusa (Functional Safety) Enable Fusa Feature on Opio, 0: Disable, 1: Enable
  $EN_DIS
**/
  UINT8                       OpioFusaConfigEnable;

/** Offset 0x0B13 - Fusa Psf Configuration
  Fusa (Functional Safety) Enable Fusa Feature on Psf, 0: Disable, 1: Enable
  $EN_DIS
**/
  UINT8                       PsfFusaConfigEnable;

/** Offset 0x0B14 - Thermal Throttling Custimized T0Level Value
  Custimized T0Level value.
**/
  UINT16                      PchT0Level;

/** Offset 0x0B16 - Thermal Throttling Custimized T1Level Value
  Custimized T1Level value.
**/
  UINT16                      PchT1Level;

/** Offset 0x0B18 - Thermal Throttling Custimized T2Level Value
  Custimized T2Level value.
**/
  UINT16                      PchT2Level;

/** Offset 0x0B1A - Enable The Thermal Throttle
  Enable the thermal throttle function.
  $EN_DIS
**/
  UINT8                       PchTTEnable;

/** Offset 0x0B1B - PMSync State 13
  When set to 1 and the programmed GPIO pin is a 1, then PMSync state 13 will force
  at least T2 state.
  $EN_DIS
**/
  UINT8                       PchTTState13Enable;

/** Offset 0x0B1C - Thermal Throttle Lock
  Thermal Throttle Lock.
  $EN_DIS
**/
  UINT8                       PchTTLock;

/** Offset 0x0B1D - Thermal Throttling Suggested Setting
  Thermal Throttling Suggested Setting.
  $EN_DIS
**/
  UINT8                       TTSuggestedSetting;

/** Offset 0x0B1E - Enable PCH Cross Throttling
  Enable/Disable PCH Cross Throttling
  $EN_DIS
**/
  UINT8                       TTCrossThrottling;

/** Offset 0x0B1F - DMI Thermal Sensor Autonomous Width Enable
  DMI Thermal Sensor Autonomous Width Enable.
  $EN_DIS
**/
  UINT8                       PchDmiTsawEn;

/** Offset 0x0B20 - DMI Thermal Sensor Suggested Setting
  DMT thermal sensor suggested representative values.
  $EN_DIS
**/
  UINT8                       DmiSuggestedSetting;

/** Offset 0x0B21 - Thermal Sensor 0 Target Width
  Thermal Sensor 0 Target Width.
  0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
  UINT8                       DmiTS0TW;

/** Offset 0x0B22 - Thermal Sensor 1 Target Width
  Thermal Sensor 1 Target Width.
  0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
  UINT8                       DmiTS1TW;

/** Offset 0x0B23 - Thermal Sensor 2 Target Width
  Thermal Sensor 2 Target Width.
  0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
  UINT8                       DmiTS2TW;

/** Offset 0x0B24 - Thermal Sensor 3 Target Width
  Thermal Sensor 3 Target Width.
  0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
  UINT8                       DmiTS3TW;

/** Offset 0x0B25 - Port 0 T1 Multipler
  Port 0 T1 Multipler.
**/
  UINT8                       SataP0T1M;

/** Offset 0x0B26 - Port 0 T2 Multipler
  Port 0 T2 Multipler.
**/
  UINT8                       SataP0T2M;

/** Offset 0x0B27 - Port 0 T3 Multipler
  Port 0 T3 Multipler.
**/
  UINT8                       SataP0T3M;

/** Offset 0x0B28 - Port 0 Tdispatch
  Port 0 Tdispatch.
**/
  UINT8                       SataP0TDisp;

/** Offset 0x0B29 - Port 1 T1 Multipler
  Port 1 T1 Multipler.
**/
  UINT8                       SataP1T1M;

/** Offset 0x0B2A - Port 1 T2 Multipler
  Port 1 T2 Multipler.
**/
  UINT8                       SataP1T2M;

/** Offset 0x0B2B - Port 1 T3 Multipler
  Port 1 T3 Multipler.
**/
  UINT8                       SataP1T3M;

/** Offset 0x0B2C - Port 1 Tdispatch
  Port 1 Tdispatch.
**/
  UINT8                       SataP1TDisp;

/** Offset 0x0B2D - Port 0 Tinactive
  Port 0 Tinactive.
**/
  UINT8                       SataP0Tinact;

/** Offset 0x0B2E - Port 0 Alternate Fast Init Tdispatch
  Port 0 Alternate Fast Init Tdispatch.
  $EN_DIS
**/
  UINT8                       SataP0TDispFinit;

/** Offset 0x0B2F - Port 1 Tinactive
  Port 1 Tinactive.
**/
  UINT8                       SataP1Tinact;

/** Offset 0x0B30 - Port 1 Alternate Fast Init Tdispatch
  Port 1 Alternate Fast Init Tdispatch.
  $EN_DIS
**/
  UINT8                       SataP1TDispFinit;

/** Offset 0x0B31 - Sata Thermal Throttling Suggested Setting
  Sata Thermal Throttling Suggested Setting.
  $EN_DIS
**/
  UINT8                       SataThermalSuggestedSetting;

/** Offset 0x0B32 - Enable Memory Thermal Throttling
  Enable Memory Thermal Throttling.
  $EN_DIS
**/
  UINT8                       PchMemoryThrottlingEnable;

/** Offset 0x0B33 - Memory Thermal Throttling
  Enable Memory Thermal Throttling.
**/
  UINT8                       PchMemoryPmsyncEnable[2];

/** Offset 0x0B35 - Enable Memory Thermal Throttling
  Enable Memory Thermal Throttling.
**/
  UINT8                       PchMemoryC0TransmitEnable[2];

/** Offset 0x0B37 - Enable Memory Thermal Throttling
  Enable Memory Thermal Throttling.
**/
  UINT8                       PchMemoryPinSelection[2];

/** Offset 0x0B39
**/
  UINT8                       UnusedUpdSpace41;

/** Offset 0x0B3A - Thermal Device Temperature
  Decides the temperature.
**/
  UINT16                      PchTemperatureHotLevel;

/** Offset 0x0B3C - Enable xHCI Compliance Mode
  Compliance Mode can be enabled for testing through this option but this is disabled
  by default.
  $EN_DIS
**/
  UINT8                       PchEnableComplianceMode;

/** Offset 0x0B3D - USB2 Port Over Current Pin
  Describe the specific over current pin number of USB 2.0 Port N.
**/
  UINT8                       Usb2OverCurrentPin[16];

/** Offset 0x0B4D - USB3 Port Over Current Pin
  Describe the specific over current pin number of USB 3.0 Port N.
**/
  UINT8                       Usb3OverCurrentPin[10];

/** Offset 0x0B57 - Enable xHCI LTR override
  Enables override of recommended LTR values for xHCI
  $EN_DIS
**/
  UINT8                       PchUsbLtrOverrideEnable;

/** Offset 0x0B58 - USB Clock Gating Enable
  Enable or disable USB clock gating
  $EN_DIS
**/
  UINT8                       UsbClockGatingEnable;

/** Offset 0x0B59 - USB Power Gating Enable
  Enable or disable USB power gating
  $EN_DIS
**/
  UINT8                       UsbPowerGatingEnable;

/** Offset 0x0B5A - USB3 LINK SPEED
  Set USB3 LINK SPEED=0 for GEN2, Set USB3 LINK SPEED=1 for GEN1
**/
  UINT8                       USB3LinkSpeed;

/** Offset 0x0B5B
**/
  UINT8                       UnusedUpdSpace42;

/** Offset 0x0B5C - xHCI High Idle Time LTR override
  Value used for overriding LTR recommendation for xHCI High Idle Time LTR setting
**/
  UINT32                      PchUsbLtrHighIdleTimeOverride;

/** Offset 0x0B60 - xHCI Medium Idle Time LTR override
  Value used for overriding LTR recommendation for xHCI Medium Idle Time LTR setting
**/
  UINT32                      PchUsbLtrMediumIdleTimeOverride;

/** Offset 0x0B64 - xHCI Low Idle Time LTR override
  Value used for overriding LTR recommendation for xHCI Low Idle Time LTR setting
**/
  UINT32                      PchUsbLtrLowIdleTimeOverride;

/** Offset 0x0B68 - Enable 8254 Static Clock Gating
  Set 8254CGE=1 is required for SLP_S0 support. However, set 8254CGE=1 in POST time
  might fail to boot legacy OS using 8254 timer. Make sure it is disabled to support
  legacy OS using 8254 timer. Also enable this while S0ix is enabled.
  $EN_DIS
**/
  UINT8                       Enable8254ClockGating;

/** Offset 0x0B69 - Enable 8254 Static Clock Gating On S3
  This is only applicable when Enable8254ClockGating is disabled. FSP will do the
  8254 CGE programming on S3 resume when Enable8254ClockGatingOnS3 is enabled. This
  avoids the SMI requirement for the programming.
  $EN_DIS
**/
  UINT8                       Enable8254ClockGatingOnS3;

/** Offset 0x0B6A - PCH Sata Rst Optane Memory
  Optane Memory
  $EN_DIS
**/
  UINT8                       SataRstOptaneMemory;

/** Offset 0x0B6B - PCH Sata Rst CPU Attached Storage
  CPU Attached Storage
  $EN_DIS
**/
  UINT8                       SataRstCpuAttachedStorage;

/** Offset 0x0B6C - Enable TCO timer.
  When FALSE, it disables PCH ACPI timer, and stops TCO timer. NOTE: This will have
  huge power impact when it's enabled. If TCO timer is disabled, uCode ACPI timer
  emulation must be enabled, and WDAT table must not be exposed to the OS.
  $EN_DIS
**/
  UINT8                       EnableTcoTimer;

/** Offset 0x0B6D - Enable Timed GPIO 0.
  When FALSE, it disables Timed GPIO 0.
  $EN_DIS
**/
  UINT8                       EnableTimedGpio0;

/** Offset 0x0B6E - Enable Timed GPIO 1.
  When FALSE, it disables Timed GPIO 1.
  $EN_DIS
**/
  UINT8                       EnableTimedGpio1;

/** Offset 0x0B6F - Enable VNN Voltage Raise.
  When TRUE, it enable VNN Voltage Raise.
  $EN_DIS
**/
  UINT8                       EnableVnnVoltageRaise;

/** Offset 0x0B70 - BgpdtHash[4]
  BgpdtHash values
**/
  UINT64                      BgpdtHash[4];

/** Offset 0x0B90 - BiosGuardAttr
  BiosGuardAttr default values
**/
  UINT32                      BiosGuardAttr;

/** Offset 0x0B94
**/
  UINT8                       UnusedUpdSpace43[4];

/** Offset 0x0B98 - BiosGuardModulePtr
  BiosGuardModulePtr default values
**/
  UINT64                      BiosGuardModulePtr;

/** Offset 0x0BA0 - SendEcCmd
  SendEcCmd function pointer. \n
  @code typedef EFI_STATUS (EFIAPI *PLATFORM_SEND_EC_COMMAND) (IN EC_COMMAND_TYPE
  EcCmdType, IN UINT8  EcCmd, IN UINT8  SendData, IN OUT UINT8  *ReceiveData); @endcode
**/
  UINT64                      SendEcCmd;

/** Offset 0x0BA8 - EcCmdProvisionEav
  Ephemeral Authorization Value default values. Provisions an ephemeral shared secret to the EC
**/
  UINT8                       EcCmdProvisionEav;

/** Offset 0x0BA9 - EcCmdLock
  EcCmdLock default values. Locks Ephemeral Authorization Value sent previously
**/
  UINT8                       EcCmdLock;

/** Offset 0x0BAA - Si Config CSM Flag.
  Platform specific common policies that used by several silicon components. CSM status flag.
  $EN_DIS
**/
  UINT8                       SiCsmFlag;

/** Offset 0x0BAB - Skip Ssid Programming.
  When set to TRUE, silicon code will not do any SSID programming and platform code
  needs to handle that by itself properly.
  $EN_DIS
**/
  UINT8                       SiSkipSsidProgramming;

/** Offset 0x0BAC - Change Default SVID
  Change the default SVID used in FSP to programming internal devices. This is only
  valid when SkipSsidProgramming is FALSE.
**/
  UINT16                      SiCustomizedSvid;

/** Offset 0x0BAE - Change Default SSID
  Change the default SSID used in FSP to programming internal devices. This is only
  valid when SkipSsidProgramming is FALSE.
**/
  UINT16                      SiCustomizedSsid;

/** Offset 0x0BB0 - SVID SDID table Poniter.
  The address of the table of SVID SDID to customize each SVID SDID entry. This is
  only valid when SkipSsidProgramming is FALSE.
**/
  UINT32                      SiSsidTablePtr;

/** Offset 0x0BB4 - Number of ssid table.
  SiNumberOfSsidTableEntry should match the table entries created in SiSsidTablePtr.
  This is only valid when SkipSsidProgramming is FALSE.
**/
  UINT16                      SiNumberOfSsidTableEntry;

/** Offset 0x0BB6
**/
  UINT8                       SiPostMemRsvd[16];

/** Offset 0x0BC6 - SATA RST Interrupt Mode
  Allowes to choose which interrupts will be implemented by SATA controller in RAID mode.
  0:Msix, 1:Msi, 2:Legacy
**/
  UINT8                       SataRstInterrupt;

/** Offset 0x0BC7 - ME Unconfig on RTC clear
  0: Disable ME Unconfig On Rtc Clear. <b>1: Enable ME Unconfig On Rtc Clear</b>.
  2: Cmos is clear, status unkonwn. 3: Reserved
  0: Disable ME Unconfig On Rtc Clear, 1: Enable ME Unconfig On Rtc Clear, 2: Cmos
  is clear, 3: Reserved
**/
  UINT8                       MeUnconfigOnRtcClear;

/** Offset 0x0BC8 - Enable PS_ON.
  PS_ON is a new C10 state from the CPU on desktop SKUs that enables a lower power
  target that will be required by the California Energy Commission (CEC). When FALSE,
  PS_ON is to be disabled.
  $EN_DIS
**/
  UINT8                       PsOnEnable;

/** Offset 0x0BC9 - Pmc Cpu C10 Gate Pin Enable
  Enable/Disable platform support for CPU_C10_GATE# pin to control gating of CPU VccIO
  and VccSTG rails instead of SLP_S0# pin.
  $EN_DIS
**/
  UINT8                       PmcCpuC10GatePinEnable;

/** Offset 0x0BCA - Pch Dmi Aspm Ctrl
  ASPM configuration on the PCH side of the DMI/OPI Link. Default is <b>PchPcieAspmAutoConfig</b>
  0:Disabled, 1:L0s, 2:L1, 3:L0sL1, 4:Auto
**/
  UINT8                       PchDmiAspmCtrl;

/** Offset 0x0BCB - PchDmiCwbEnable
  Central Write Buffer feature configurable and disabled by default
  $EN_DIS
**/
  UINT8                       PchDmiCwbEnable;

/** Offset 0x0BCC - OS IDLE Mode Enable
  Enable/Disable OS Idle Mode
  $EN_DIS
**/
  UINT8                       PmcOsIdleEnable;

/** Offset 0x0BCD - S0ix Auto-Demotion
  Enable/Disable the Low Power Mode Auto-Demotion Host Control feature.
  $EN_DIS
**/
  UINT8                       PchS0ixAutoDemotion;

/** Offset 0x0BCE - Global Reset TSC Enable
  Enable/Disable PMC Global Reset Three Strike Counter feature. If enabled, PMC will
  keep the platform in S5 after the third consecutive type 7 global reset occurs
  during boot flow
  $EN_DIS
**/
  UINT8                       PmcGrTscEnable;

/** Offset 0x0BCF - Latch Events C10 Exit
  When this bit is set to 1, SLP_S0# entry events in SLP_S0_DEBUG_REGx registers are
  captured on C10 exit (instead of C10 entry which is default)
  $EN_DIS
**/
  UINT8                       PchPmLatchEventsC10Exit;

/** Offset 0x0BD0 - PCIE Eq Ph3 Lane Param Cm
  CPU_PCIE_EQ_LANE_PARAM. Coefficient C-1.
**/
  UINT8                       CpuPcieEqPh3LaneParamCm[32];

/** Offset 0x0BF0 - PCIE Eq Ph3 Lane Param Cp
  CPU_PCIE_EQ_LANE_PARAM. Coefficient C+1.
**/
  UINT8                       CpuPcieEqPh3LaneParamCp[32];

/** Offset 0x0C10 - PCIE Hw Eq Gen3 CoeffList Cm
  CPU_PCIE_EQ_PARAM. Coefficient C-1.
**/
  UINT8                       CpuPcieHwEqGen3CoeffListCm[5];

/** Offset 0x0C15 - PCIE Hw Eq Gen3 CoeffList Cp
  CPU_PCIE_EQ_PARAM. Coefficient C+1.
**/
  UINT8                       CpuPcieHwEqGen3CoeffListCp[5];

/** Offset 0x0C1A - PCIE Hw Eq Gen4 CoeffList Cm
  CPU_PCIE_EQ_PARAM. Coefficient C-1.
**/
  UINT8                       CpuPcieHwEqGen4CoeffListCm[5];

/** Offset 0x0C1F - PCIE Hw Eq Gen4 CoeffList Cp
  CPU_PCIE_EQ_PARAM. Coefficient C+1.
**/
  UINT8                       CpuPcieHwEqGen4CoeffListCp[5];

/** Offset 0x0C24 - Gen3 Root port preset values per lane
  Used for programming Pcie Gen3 preset values per lane. Range: 0-9, 8 is default
  for each lane
**/
  UINT8                       CpuPcieGen3RootPortPreset[20];

/** Offset 0x0C38 - Pcie Gen4 Root port preset values per lane
  Used for programming Pcie Gen4 preset values per lane. Range: 0-9, 8 is default
  for each lane
**/
  UINT8                       CpuPcieGen4RootPortPreset[20];

/** Offset 0x0C4C - Pcie Gen3 End port preset values per lane
  Used for programming Pcie Gen3 preset values per lane. Range: 0-9, 7 is default
  for each lane
**/
  UINT8                       CpuPcieGen3EndPointPreset[20];

/** Offset 0x0C60 - Pcie Gen4 End port preset values per lane
  Used for programming Pcie Gen4 preset values per lane. Range: 0-9, 7 is default
  for each lane
**/
  UINT8                       CpuPcieGen4EndPointPreset[20];

/** Offset 0x0C74 - Pcie Gen3 End port Hint values per lane
  Used for programming Pcie Gen3 Hint values per lane. Range: 0-6, 2 is default for each lane
**/
  UINT8                       CpuPcieGen3EndPointHint[20];

/** Offset 0x0C88 - Pcie Gen4 End port Hint values per lane
  Used for programming Pcie Gen4 Hint values per lane. Range: 0-6, 2 is default for each lane
**/
  UINT8                       CpuPcieGen4EndPointHint[20];

/** Offset 0x0C9C - Skip Cpu Fia Programming
  Skip Fia configuration and lock if enable. 0: Disable; 1: Enable.
  $EN_DIS
**/
  UINT8                       CpuPcieSkipCpuFiaProgramming;

/** Offset 0x0C9D - PCIE Disable RootPort Clock Gating
  Describes whether the PCI Express Clock Gating for each root port is enabled by
  platform modules. 0: Disable; 1: Enable.
  $EN_DIS
**/
  UINT8                       CpuPcieDisableRootPortClockGating;

/** Offset 0x0C9E - PCIE Disable RootPort Power Gating
  Describes whether the PCI Express Power Gating for each root port is enabled by
  platform modules. 0: Disable; 1: Enable.
  $EN_DIS
**/
  UINT8                       CpuPcieDisableRootPortPowerGating;

/** Offset 0x0C9F - PCIE Compliance Test Mode
  Compliance Test Mode shall be enabled when using Compliance Load Board.
  $EN_DIS
**/
  UINT8                       CpuPcieComplianceTestMode;

/** Offset 0x0CA0 - PCIE Secure Register Lock
  Describes whether Secure Register Lock is enaled or disabled. When it will be enbaled,
  load CpuPcieRpSetSecuredRegisterLock recipe. 0: Disable(Default); 1: Enable
  $EN_DIS
**/
  UINT8                       CpuPcieSetSecuredRegisterLock;

/** Offset 0x0CA1 - PCIE Enable Peer Memory Write
  This member describes whether Peer Memory Writes are enabled on the platform.
  $EN_DIS
**/
  UINT8                       CpuPcieEnablePeerMemoryWrite;

/** Offset 0x0CA2 - PCIE Rp Function Swap
  Allows BIOS to use root port function number swapping when root port of function
  0 is disabled.
  $EN_DIS
**/
  UINT8                       CpuPcieRpFunctionSwap;

/** Offset 0x0CA3
**/
  UINT8                       UnusedUpdSpace44;

/** Offset 0x0CA4 - Pch PCIE device override table pointer
  The PCIe device table is being used to override PCIe device ASPM settings. This
  is a pointer points to a 32bit address. And it's only used in PostMem phase. Please
  refer to CPU_PCIE_DEVICE_OVERRIDE structure for the table. Last entry VendorId
  must be 0.
**/
  UINT32                      CpuPcieDeviceOverrideTablePtr;

/** Offset 0x0CA8 - Enable PCIE RP HotPlug
  Indicate whether the root port is hot plug available.
**/
  UINT8                       CpuPcieRpHotPlug[4];

/** Offset 0x0CAC - Enable PCIE RP Pm Sci
  Indicate whether the root port power manager SCI is enabled.
**/
  UINT8                       CpuPcieRpPmSci[4];

/** Offset 0x0CB0 - Enable PCIE RP Transmitter Half Swing
  Indicate whether the Transmitter Half Swing is enabled.
**/
  UINT8                       CpuPcieRpTransmitterHalfSwing[4];

/** Offset 0x0CB4 - PCIE RP Access Control Services Extended Capability
  Enable/Disable PCIE RP Access Control Services Extended Capability
**/
  UINT8                       CpuPcieRpAcsEnabled[4];

/** Offset 0x0CB8 - PCIE RP Clock Power Management
  Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal
  can still be controlled by L1 PM substates mechanism
**/
  UINT8                       CpuPcieRpEnableCpm[4];

/** Offset 0x0CBC - PCIE RP Advanced Error Report
  Indicate whether the Advanced Error Reporting is enabled.
**/
  UINT8                       CpuPcieRpAdvancedErrorReporting[4];

/** Offset 0x0CC0 - PCIE RP Unsupported Request Report
  Indicate whether the Unsupported Request Report is enabled.
**/
  UINT8                       CpuPcieRpUnsupportedRequestReport[4];

/** Offset 0x0CC4 - PCIE RP Fatal Error Report
  Indicate whether the Fatal Error Report is enabled.
**/
  UINT8                       CpuPcieRpFatalErrorReport[4];

/** Offset 0x0CC8 - PCIE RP No Fatal Error Report
  Indicate whether the No Fatal Error Report is enabled.
**/
  UINT8                       CpuPcieRpNoFatalErrorReport[4];

/** Offset 0x0CCC - PCIE RP Correctable Error Report
  Indicate whether the Correctable Error Report is enabled.
**/
  UINT8                       CpuPcieRpCorrectableErrorReport[4];

/** Offset 0x0CD0 - PCIE RP System Error On Fatal Error
  Indicate whether the System Error on Fatal Error is enabled.
**/
  UINT8                       CpuPcieRpSystemErrorOnFatalError[4];

/** Offset 0x0CD4 - PCIE RP System Error On Non Fatal Error
  Indicate whether the System Error on Non Fatal Error is enabled.
**/
  UINT8                       CpuPcieRpSystemErrorOnNonFatalError[4];

/** Offset 0x0CD8 - PCIE RP System Error On Correctable Error
  Indicate whether the System Error on Correctable Error is enabled.
**/
  UINT8                       CpuPcieRpSystemErrorOnCorrectableError[4];

/** Offset 0x0CDC - PCIE RP Max Payload
  Max Payload Size supported, Default 128B, see enum PCH_PCIE_MAX_PAYLOAD.
**/
  UINT8                       CpuPcieRpMaxPayload[4];

/** Offset 0x0CE0 - DPC for PCIE RP Mask
  Enable/disable Downstream Port Containment for PCIE Root Ports. 0: disable, 1: enable.
  One bit for each port, bit0 for port1, bit1 for port2, and so on.
**/
  UINT8                       CpuPcieRpDpcEnabled[4];

/** Offset 0x0CE4 - DPC Extensions PCIE RP Mask
  Enable/disable DPC Extensions for PCIE Root Ports. 0: disable, 1: enable. One bit
  for each port, bit0 for port1, bit1 for port2, and so on.
**/
  UINT8                       CpuPcieRpDpcExtensionsEnabled[4];

/** Offset 0x0CE8 - PCH PCIe root port connection type
  0: built-in device, 1:slot
**/
  UINT8                       CpuPcieRpSlotImplemented[4];

/** Offset 0x0CEC - PCIE RP Gen3 Equalization Phase Method
  PCIe Gen3 Eq Ph3 Method (see CPU_PCIE_EQ_METHOD). 0: DEPRECATED, hardware equalization;
  1: hardware equalization; 4: Fixed Coeficients.
**/
  UINT8                       CpuPcieRpGen3EqPh3Method[4];

/** Offset 0x0CF0 - PCIE RP Gen4 Equalization Phase Method
  PCIe Gen4 Eq Ph3 Method (see CPU_PCIE_EQ_METHOD). 0: DEPRECATED, hardware equalization;
  1: hardware equalization; 4: Fixed Coeficients.
**/
  UINT8                       CpuPcieRpGen4EqPh3Method[4];

/** Offset 0x0CF4 - Phase3 RP Gen3 EQ enable
  Phase3 Gen3 EQ enable. Disabled(0x0): Disable phase 3, Enabled(0x1): Enable phase
  3, Auto(0x2)(Default): Use the current default method
  0:Disable, 1:Enable, 2:Auto
**/
  UINT8                       CpuPcieRpGen3EqPh3Enable[4];

/** Offset 0x0CF8 - Phase3 RP Gen4 EQ enable
  Phase3 Gen4 EQ enable. Disabled(0x0): Disable phase 3, Enabled(0x1): Enable phase
  3, Auto(0x2)(Default): Use the current default method
  0:Disable, 1:Enable, 2:Auto
**/
  UINT8                       CpuPcieRpGen4EqPh3Enable[4];

/** Offset 0x0CFC - Phase2-3 RP Gen3 EQ enable
  Phase2-3 Gen3 EQ enable. Disabled(0x0): Disable Phase2-3, Enabled(0x1): Enable Phase2-3,
  Auto(0x2)(Default): Use the current default method
  0:Disable, 1:Enable, 2:Auto
**/
  UINT8                       CpuPcieRpGen3EqPh23Enable[4];

/** Offset 0x0D00 - Phase2-3 RP Gen4 EQ enable
  Phase2-3 Gen4 EQ enable. Disabled(0x0): Disable Phase2-3, Enabled(0x1): Enable Phase2-3,
  Auto(0x2)(Default): Use the current default method
  0:Disable, 1:Enable, 2:Auto
**/
  UINT8                       CpuPcieRpGen4EqPh23Enable[4];

/** Offset 0x0D04 - PCET Timer
  Preset/Coefficient Evaluation Timeout. See CPU_PCIE_PCET. Default is 0x4
**/
  UINT8                       CpuPciePcetTimer[4];

/** Offset 0x0D08 - Gen3 Preset/Coeffiecient List Count
  Select Gen3 Hardware Autonomous Preset/Coefficient Count. See Gen3 CPU_PCIE_PRESETCOEFF_LIST.
  Default is 0x3
**/
  UINT8                       Gen3CpuPciePresetCoeffList[4];

/** Offset 0x0D0C - Gen4 Preset/Coeffiecient List Count
  Select Gen4 Hardware Autonomous Preset/Coefficient Count. See CPU_PCIE_PRESETCOEFF_LIST.
  Default is 0x3
**/
  UINT8                       Gen4CpuPciePresetCoeffList[4];

/** Offset 0x0D10 - Presets/Coefficients Evaluation for Gen3
  8.0GT/s Training Sequence Wait Latency For Presets/Coefficients Evaluation. See
  CPU_PCIE_PX8GTSWLPCE. Default is 0x3
**/
  UINT8                       CpuPciePx8gtswlpce[4];

/** Offset 0x0D14 - Presets/Coefficients Evaluation for Gen4
  16.0GT/s Training Sequence Wait Latency For Presets/Coefficients Evaluation. See
  CPU_PCIE_PX16GTSWLPCE. Default is 0x4
**/
  UINT8                       CpuPciePx16gtswlpce[4];

/** Offset 0x0D18 - PCIE RP Physical Slot Number
  Indicates the slot number for the root port. Default is the value as root port index.
**/
  UINT8                       CpuPcieRpPhysicalSlotNumber[4];

/** Offset 0x0D1C - PCIE RP Aspm
  The ASPM configuration of the root port (see: CPU_PCIE_ASPM_CONTROL). Default is
  CpuPcieAspmAutoConfig.
**/
  UINT8                       CpuPcieRpAspm[4];

/** Offset 0x0D20 - PCIE RP L1 Substates
  The L1 Substates configuration of the root port (see: CPU_PCIE_L1SUBSTATES_CONTROL).
  Default is CpuPcieL1SubstatesDisabled.
**/
  UINT8                       CpuPcieRpL1Substates[4];

/** Offset 0x0D24 - PCIE RP Ltr Enable
  Latency Tolerance Reporting Mechanism.
**/
  UINT8                       CpuPcieRpLtrEnable[4];

/** Offset 0x0D28 - PCIE RP Ltr Config Lock
  0: Disable; 1: Enable.
**/
  UINT8                       CpuPcieRpLtrConfigLock[4];

/** Offset 0x0D2C - PTM for PCIE RP Mask
  Enable/disable Precision Time Measurement for PCIE Root Ports. 0: disable, 1: enable.
  One bit for each port, bit0 for port1, bit1 for port2, and so on.
**/
  UINT8                       CpuPcieRpPtmEnabled[4];

/** Offset 0x0D30 - PCIE RP Detect Timeout Ms
  The number of milliseconds within 0~65535 in reference code will wait for link to
  exit Detect state for enabled ports before assuming there is no device and potentially
  disabling the port.
**/
  UINT16                      CpuPcieRpDetectTimeoutMs[4];

/** Offset 0x0D38 - VC for PCIE RP Mask
  Enable/disable Virtual Channel for PCIE Root Ports. 0: disable, 1: enable. One bit
  for each port, bit0 for port1, bit1 for port2, and so on.
**/
  UINT8                       CpuPcieRpVcEnabled[4];

/** Offset 0x0D3C - Force GT CLOS on LLC for Real Time Performance
  0(Default)=Disable, 1=Enable
  $EN_DIS
**/
  UINT8                       GtClosEnable;

/** Offset 0x0D3D - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3
  Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3, Each
  value in array can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate3UniqTranEnable[10];

/** Offset 0x0D47 - USB 3.0 TX Output Unique Transition Bit Scale for rate 3
  USB 3.0 TX Output Unique Transition Bit Scale for rate 3, HSIO_TX_DWORD9[6:0], <b>Default
  = 4Ch</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate3UniqTran[10];

/** Offset 0x0D51 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2
  Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2, Each
  value in array can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate2UniqTranEnable[10];

/** Offset 0x0D5B - USB 3.0 TX Output Unique Transition Bit Scale for rate 2
  USB 3.0 TX Output Unique Transition Bit Scale for rate 2, HSIO_TX_DWORD9[14:8],
  <b>Default = 4Ch</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate2UniqTran[10];

/** Offset 0x0D65 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1
  Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1, Each
  value in array can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate1UniqTranEnable[10];

/** Offset 0x0D6F - USB 3.0 TX Output Unique Transition Bit Scale for rate 1
  USB 3.0 TX Output Unique Transition Bit Scale for rate 1, HSIO_TX_DWORD9[22:16],
  <b>Default = 4Ch</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate1UniqTran[10];

/** Offset 0x0D79 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0
  Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0, Each
  value in array can be between 0-1. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate0UniqTranEnable[10];

/** Offset 0x0D83 - USB 3.0 TX Output Unique Transition Bit Scale for rate 0
  USB 3.0 TX Output Unique Transition Bit Scale for rate 0, HSIO_TX_DWORD9[30:24],
  <b>Default = 4Ch</b>. One byte for each port.
**/
  UINT8                       Usb3HsioTxRate0UniqTran[10];

/** Offset 0x0D8D - Skip PAM regsiter lock
  Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
  PAM registers will be locked by RC
  $EN_DIS
**/
  UINT8                       SkipPamLock;

/** Offset 0x0D8E - EDRAM Test Mode
  Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
  PAM registers will be locked by RC
  0: EDRAM SW disable, 1: EDRAM SW Enable, 2: EDRAM HW mode
**/
  UINT8                       EdramTestMode;

/** Offset 0x0D8F - Enable/Disable IGFX RenderStandby
  Enable(Default): Enable IGFX RenderStandby, Disable: Disable IGFX RenderStandby
  $EN_DIS
**/
  UINT8                       RenderStandby;

/** Offset 0x0D90 - Enable/Disable IGFX PmSupport
  Enable(Default): Enable IGFX PmSupport, Disable: Disable IGFX PmSupport
  $EN_DIS
**/
  UINT8                       PmSupport;

/** Offset 0x0D91 - Enable/Disable CdynmaxClamp
  Enable: Enable CdynmaxClamp, Disable(Default): Disable CdynmaxClamp
  $EN_DIS
**/
  UINT8                       CdynmaxClampEnable;

/** Offset 0x0D92 - GT Frequency Limit
  0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
  7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
  650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
  0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
  0x18: 1200 Mhz
  0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
  7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
  650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
  0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
  0x18: 1200 Mhz
**/
  UINT8                       GtFreqMax;

/** Offset 0x0D93 - Disable Turbo GT
   0=Disable: GT frequency is not limited, 1=Enable: Disables Turbo GT frequency
  $EN_DIS
**/
  UINT8                       DisableTurboGt;

/** Offset 0x0D94 - Enable/Disable CdClock Init
  Enable: Skip Full CD clock initializaton, Disable(Default): Initialize the full
  CD clock if not initialized by Gfx PEIM
  $EN_DIS
**/
  UINT8                       SkipCdClockInit;

/** Offset 0x0D95
**/
  UINT8                       UnusedUpdSpace45[3];

/** Offset 0x0D98 - LogoPixelHeight Address
  Address of LogoPixelHeight
**/
  UINT32                      LogoPixelHeight;

/** Offset 0x0D9C - LogoPixelWidth Address
  Address of LogoPixelWidth
**/
  UINT32                      LogoPixelWidth;

/** Offset 0x0DA0 - SaPostMemTestRsvd
  Reserved for SA Post-Mem Test
  $EN_DIS
**/
  UINT8                       SaPostMemTestRsvd[6];

/** Offset 0x0DA6 - RSR feature
  Enable or Disable RSR feature; 0: Disable; <b>1: Enable </b>
  $EN_DIS
**/
  UINT8                       EnableRsr;

/** Offset 0x0DA7 - 1-Core Ratio Limit
  1-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused
  1-Core Ratio Limit + OC Bins.This 1-Core Ratio Limit Must be greater than or equal
  to 2-Core Ratio Limit, 3-Core Ratio Limit, 4-Core Ratio Limit. Range is 0 to 83
**/
  UINT8                       OneCoreRatioLimit;

/** Offset 0x0DA8 - 2-Core Ratio Limit
  2-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused
  2-Core Ratio Limit + OC Bins.This 2-Core Ratio Limit Must be Less than or equal
  to 1-Core Ratio Limit.Range is 0 to 83
**/
  UINT8                       TwoCoreRatioLimit;

/** Offset 0x0DA9 - 3-Core Ratio Limit
  3-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused
  3-Core Ratio Limit + OC Bins.This 3-Core Ratio Limit Must be Less than or equal
  to 1-Core Ratio Limit.Range is 0 to 83
**/
  UINT8                       ThreeCoreRatioLimit;

/** Offset 0x0DAA - 4-Core Ratio Limit
  4-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused
  4-Core Ratio Limit + OC Bins.This 4-Core Ratio Limit Must be Less than or equal
  to 1-Core Ratio Limit.Range is 0 to 83
**/
  UINT8                       FourCoreRatioLimit;

/** Offset 0x0DAB - Enable or Disable HWP
  Enable or Disable HWP(Hardware P states) Support. 0: Disable; <b>1: Enable;</b>
  2-3:Reserved
  $EN_DIS
**/
  UINT8                       Hwp;

/** Offset 0x0DAC - Hardware Duty Cycle Control
  Hardware Duty Cycle Control configuration. 0: Disabled; <b>1: Enabled</b> 2-3:Reserved
  $EN_DIS
**/
  UINT8                       HdcControl;

/** Offset 0x0DAD - Package Long duration turbo mode time
  Package Long duration turbo mode time window in seconds. Valid values(Unit in seconds)
  0 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
  UINT8                       PowerLimit1Time;

/** Offset 0x0DAE - Short Duration Turbo Mode
  Enable or Disable short duration Turbo Mode. </b>0 : Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       PowerLimit2;

/** Offset 0x0DAF - Turbo settings Lock
  Lock all Turbo settings Enable/Disable; <b>0: Disable , </b> 1: Enable
  $EN_DIS
**/
  UINT8                       TurboPowerLimitLock;

/** Offset 0x0DB0 - Package PL3 time window
  Package PL3 time window range for this policy from 0 to 64ms
**/
  UINT8                       PowerLimit3Time;

/** Offset 0x0DB1 - Package PL3 Duty Cycle
  Package PL3 Duty Cycle; Valid Range is 0 to 100
**/
  UINT8                       PowerLimit3DutyCycle;

/** Offset 0x0DB2 - Package PL3 Lock
  Package PL3 Lock Enable/Disable; <b>0: Disable</b> ; 1:Enable
  $EN_DIS
**/
  UINT8                       PowerLimit3Lock;

/** Offset 0x0DB3 - Package PL4 Lock
  Package PL4 Lock Enable/Disable; <b>0: Disable</b> ; 1:Enable
  $EN_DIS
**/
  UINT8                       PowerLimit4Lock;

/** Offset 0x0DB4 - TCC Activation Offset
  TCC Activation Offset. Offset from factory set TCC activation temperature at which
  the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation
  Temperature, in volts.For SKL Y SKU, the recommended default for this policy is
  <b>10</b>, For all other SKUs the recommended default are <b>0</b>
**/
  UINT8                       TccActivationOffset;

/** Offset 0x0DB5 - Tcc Offset Clamp Enable/Disable
  Tcc Offset Clamp for Runtime Average Temperature Limit (RATL) allows CPU to throttle
  below P1.For SKL Y SKU, the recommended default for this policy is <b>1: Enabled</b>,
  For all other SKUs the recommended default are  <b>0: Disabled</b>.
  $EN_DIS
**/
  UINT8                       TccOffsetClamp;

/** Offset 0x0DB6 - Tcc Offset Lock
  Tcc Offset Lock for Runtime Average Temperature Limit (RATL) to lock temperature
  target; <b>0: Disabled</b>; 1: Enabled.
  $EN_DIS
**/
  UINT8                       TccOffsetLock;

/** Offset 0x0DB7 - Custom Ratio State Entries
  The number of custom ratio state entries, ranges from 0 to 40 for a valid custom
  ratio table.Sets the number of custom P-states. At least 2 states must be present
**/
  UINT8                       NumberOfEntries;

/** Offset 0x0DB8 - Custom Short term Power Limit time window
  Short term Power Limit time window value for custom CTDP level 1. Valid Range 0 to 128
**/
  UINT8                       Custom1PowerLimit1Time;

/** Offset 0x0DB9 - Custom Turbo Activation Ratio
  Turbo Activation Ratio for custom cTDP level 1. Valid Range 0 to 255
**/
  UINT8                       Custom1TurboActivationRatio;

/** Offset 0x0DBA - Custom Config Tdp Control
  Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
  UINT8                       Custom1ConfigTdpControl;

/** Offset 0x0DBB - Custom Short term Power Limit time window
  Short term Power Limit time window value for custom CTDP level 2. Valid Range 0 to 128
**/
  UINT8                       Custom2PowerLimit1Time;

/** Offset 0x0DBC - Custom Turbo Activation Ratio
  Turbo Activation Ratio for custom cTDP level 2. Valid Range 0 to 255
**/
  UINT8                       Custom2TurboActivationRatio;

/** Offset 0x0DBD - Custom Config Tdp Control
  Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
  UINT8                       Custom2ConfigTdpControl;

/** Offset 0x0DBE - Custom Short term Power Limit time window
  Short term Power Limit time window value for custom CTDP level 3. Valid Range 0 to 128
**/
  UINT8                       Custom3PowerLimit1Time;

/** Offset 0x0DBF - Custom Turbo Activation Ratio
  Turbo Activation Ratio for custom cTDP level 3. Valid Range 0 to 255
**/
  UINT8                       Custom3TurboActivationRatio;

/** Offset 0x0DC0 - Custom Config Tdp Control
  Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
  UINT8                       Custom3ConfigTdpControl;

/** Offset 0x0DC1 - ConfigTdp mode settings Lock
  Lock the ConfigTdp mode settings from runtime changes; <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       ConfigTdpLock;

/** Offset 0x0DC2 - Load Configurable TDP SSDT
  Configure whether to load Configurable TDP SSDT; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       ConfigTdpBios;

/** Offset 0x0DC3 - PL1 Enable value
  PL1 Enable value to limit average platform power. <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       PsysPowerLimit1;

/** Offset 0x0DC4 - PL1 timewindow
  PL1 timewindow in seconds.Valid values(Unit in seconds) 0 to 8 , 10 , 12 ,14 , 16
  , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
  UINT8                       PsysPowerLimit1Time;

/** Offset 0x0DC5 - PL2 Enable Value
  PL2 Enable activates the PL2 value to limit average platform power.<b>0: Disable</b>;
  1: Enable.
  $EN_DIS
**/
  UINT8                       PsysPowerLimit2;

/** Offset 0x0DC6 - Enable or Disable MLC Streamer Prefetcher
  Enable or Disable MLC Streamer Prefetcher; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       MlcStreamerPrefetcher;

/** Offset 0x0DC7 - Enable or Disable MLC Spatial Prefetcher
  Enable or Disable MLC Spatial Prefetcher; 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       MlcSpatialPrefetcher;

/** Offset 0x0DC8 - Enable or Disable Monitor /MWAIT instructions
  Enable or Disable Monitor /MWAIT instructions; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       MonitorMwaitEnable;

/** Offset 0x0DC9 - Enable or Disable initialization of machine check registers
  Enable or Disable initialization of machine check registers; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       MachineCheckEnable;

/** Offset 0x0DCA - Check if FUSA is supported
  Check if FUSA is supported; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       IsFusaSupported;

/** Offset 0x0DCB - AP Idle Manner of waiting for SIPI
  AP Idle Manner of waiting for SIPI; 1: HALT loop; <b>2: MWAIT loop</b>; 3: RUN loop.
  1: HALT loop, 2: MWAIT loop, 3: RUN loop
**/
  UINT8                       ApIdleManner;

/** Offset 0x0DCC - Control on Processor Trace output scheme
  Control on Processor Trace output scheme; <b>0: Single Range Output</b>; 1: ToPA Output.
  0: Single Range Output, 1: ToPA Output
**/
  UINT8                       ProcessorTraceOutputScheme;

/** Offset 0x0DCD - Enable or Disable Processor Trace feature
  Enable or Disable Processor Trace feature; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       ProcessorTraceEnable;

/** Offset 0x0DCE - Enable or Disable Intel SpeedStep Technology
  Enable or Disable Intel SpeedStep Technology. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       Eist;

/** Offset 0x0DCF - Enable or Disable Energy Efficient P-state
  Enable or Disable Energy Efficient P-state will be applied in Turbo mode. Disable;
  <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       EnergyEfficientPState;

/** Offset 0x0DD0 - Enable or Disable Energy Efficient Turbo
  Enable or Disable Energy Efficient Turbo, will be applied in Turbo mode. Disable;
  <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       EnergyEfficientTurbo;

/** Offset 0x0DD1 - Enable or Disable T states
  Enable or Disable T states; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       TStates;

/** Offset 0x0DD2 - Enable or Disable Bi-Directional PROCHOT#
  Enable or Disable Bi-Directional PROCHOT#; 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       BiProcHot;

/** Offset 0x0DD3 - Enable or Disable PROCHOT# signal being driven externally
  Enable or Disable PROCHOT# signal being driven externally; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       DisableProcHotOut;

/** Offset 0x0DD4 - Enable or Disable PROCHOT# Response
  Enable or Disable PROCHOT# Response; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       ProcHotResponse;

/** Offset 0x0DD5 - Enable or Disable VR Thermal Alert
  Enable or Disable VR Thermal Alert; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       DisableVrThermalAlert;

/** Offset 0x0DD6 - Enable or Disable Thermal Reporting
  Enable or Disable Thermal Reporting through ACPI tables; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       EnableAllThermalFunctions;

/** Offset 0x0DD7 - Enable or Disable Thermal Monitor
  Enable or Disable Thermal Monitor; 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       ThermalMonitor;

/** Offset 0x0DD8 - Enable or Disable CPU power states (C-states)
  Enable or Disable CPU power states (C-states). 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       Cx;

/** Offset 0x0DD9 - Configure C-State Configuration Lock
  Configure C-State Configuration Lock; 0: Disable; <b>1: Enable</b>.
  $EN_DIS
**/
  UINT8                       PmgCstCfgCtrlLock;

/** Offset 0x0DDA - Enable or Disable Enhanced C-states
  Enable or Disable Enhanced C-states. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       C1e;

/** Offset 0x0DDB - Enable or Disable Package Cstate Demotion
  Enable or Disable Package Cstate Demotion. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       PkgCStateDemotion;

/** Offset 0x0DDC - Enable or Disable Package Cstate UnDemotion
  Enable or Disable Package Cstate UnDemotion. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       PkgCStateUnDemotion;

/** Offset 0x0DDD - Enable or Disable CState-Pre wake
  Enable or Disable CState-Pre wake. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       CStatePreWake;

/** Offset 0x0DDE - Enable or Disable TimedMwait Support.
  Enable or Disable TimedMwait Support. <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       TimedMwait;

/** Offset 0x0DDF - Enable or Disable IO to MWAIT redirection
  Enable or Disable IO to MWAIT redirection; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       CstCfgCtrIoMwaitRedirection;

/** Offset 0x0DE0 - Set the Max Pkg Cstate
  Set the Max Pkg Cstate. Default set to Auto which limits the Max Pkg Cstate to deep
  C-state. Valid values 0 - C0/C1 , 1 - C2 , 2 - C3 , 3 - C6 , 4 - C7 , 5 - C7S ,
  6 - C8 , 7 - C9 , 8 - C10 , 254 - CPU Default , 255 - Auto
**/
  UINT8                       PkgCStateLimit;

/** Offset 0x0DE1 - TimeUnit for C-State Latency Control0
  TimeUnit for C-State Latency Control0; Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
  , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl0TimeUnit;

/** Offset 0x0DE2 - TimeUnit for C-State Latency Control1
  TimeUnit for C-State Latency Control1;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
  , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl1TimeUnit;

/** Offset 0x0DE3 - TimeUnit for C-State Latency Control2
  TimeUnit for C-State Latency Control2;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
  , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl2TimeUnit;

/** Offset 0x0DE4 - TimeUnit for C-State Latency Control3
  TimeUnit for C-State Latency Control3;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
  , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl3TimeUnit;

/** Offset 0x0DE5 - TimeUnit for C-State Latency Control4
  Time - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl4TimeUnit;

/** Offset 0x0DE6 - TimeUnit for C-State Latency Control5
  TimeUnit for C-State Latency Control5;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
  , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
  UINT8                       CstateLatencyControl5TimeUnit;

/** Offset 0x0DE7 - Interrupt Redirection Mode Select
  Interrupt Redirection Mode Select.0: Fixed priority; 1: Round robin;2: Hash vector;7:
  No change.
**/
  UINT8                       PpmIrmSetting;

/** Offset 0x0DE8 - Lock prochot configuration
  Lock prochot configuration Enable/Disable; <b>0: Disable</b>; 1: Enable
  $EN_DIS
**/
  UINT8                       ProcHotLock;

/** Offset 0x0DE9 - Configuration for boot TDP selection
  Configuration for boot TDP selection; <b>0: TDP Nominal</b>; 1: TDP Down; 2: TDP
  Up;0xFF : Deactivate
**/
  UINT8                       ConfigTdpLevel;

/** Offset 0x0DEA - Max P-State Ratio
  Max P-State Ratio, Valid Range 0 to 0x7F
**/
  UINT8                       MaxRatio;

/** Offset 0x0DEB - P-state ratios for custom P-state table
  P-state ratios for custom P-state table. NumberOfEntries has valid range between
  0 to 40. For no. of P-States supported(NumberOfEntries) , StateRatio[NumberOfEntries]
  are configurable. Valid Range of each entry is 0 to 0x7F
**/
  UINT8                       StateRatio[40];

/** Offset 0x0E13 - P-state ratios for max 16 version of custom P-state table
  P-state ratios for max 16 version of custom P-state table. This table is used for
  OS versions limited to a max of 16 P-States. If the first entry of this table is
  0, or if Number of Entries is 16 or less, then this table will be ignored, and
  up to the top 16 values of the StateRatio table will be used instead. Valid Range
  of each entry is 0 to 0x7F
**/
  UINT8                       StateRatioMax16[16];

/** Offset 0x0E23
**/
  UINT8                       UnusedUpdSpace46;

/** Offset 0x0E24 - Platform Power Pmax
  PCODE MMIO Mailbox: Platform Power Pmax. <b>0 - Auto</b> Specified in 1/8 Watt increments.
  Range 0-1024 Watts. Value of 800 = 100W
**/
  UINT16                      PsysPmax;

/** Offset 0x0E26 - Interrupt Response Time Limit of C-State LatencyContol1
  Interrupt Response Time Limit of C-State LatencyContol1.Range of value 0 to 0x3FF.
  0 is Auto.
**/
  UINT16                      CstateLatencyControl1Irtl;

/** Offset 0x0E28 - Interrupt Response Time Limit of C-State LatencyContol2
  Interrupt Response Time Limit of C-State LatencyContol2.Range of value 0 to 0x3FF.
  0 is Auto.
**/
  UINT16                      CstateLatencyControl2Irtl;

/** Offset 0x0E2A - Interrupt Response Time Limit of C-State LatencyContol3
  Interrupt Response Time Limit of C-State LatencyContol3.Range of value 0 to 0x3FF.
  0 is Auto.
**/
  UINT16                      CstateLatencyControl3Irtl;

/** Offset 0x0E2C - Interrupt Response Time Limit of C-State LatencyContol4
  Interrupt Response Time Limit of C-State LatencyContol4.Range of value 0 to 0x3FF.
  0 is Auto.
**/
  UINT16                      CstateLatencyControl4Irtl;

/** Offset 0x0E2E - Interrupt Response Time Limit of C-State LatencyContol5
  Interrupt Response Time Limit of C-State LatencyContol5.Range of value 0 to 0x3FF.
  0 is Auto.
**/
  UINT16                      CstateLatencyControl5Irtl;

/** Offset 0x0E30 - Package Long duration turbo mode power limit
  Package Long duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
  Valid Range 0 to 4095875 in Step size of 125
**/
  UINT32                      PowerLimit1;

/** Offset 0x0E34 - Package Short duration turbo mode power limit
  Package Short duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      PowerLimit2Power;

/** Offset 0x0E38 - Package PL3 power limit
  Package PL3 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      PowerLimit3;

/** Offset 0x0E3C - Package PL4 power limit
  Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      PowerLimit4;

/** Offset 0x0E40 - Tcc Offset Time Window for RATL
  Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      TccOffsetTimeWindowForRatl;

/** Offset 0x0E44 - Short term Power Limit value for custom cTDP level 1
  Short term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom1PowerLimit1;

/** Offset 0x0E48 - Long term Power Limit value for custom cTDP level 1
  Long term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom1PowerLimit2;

/** Offset 0x0E4C - Short term Power Limit value for custom cTDP level 2
  Short term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom2PowerLimit1;

/** Offset 0x0E50 - Long term Power Limit value for custom cTDP level 2
  Long term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom2PowerLimit2;

/** Offset 0x0E54 - Short term Power Limit value for custom cTDP level 3
  Short term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom3PowerLimit1;

/** Offset 0x0E58 - Long term Power Limit value for custom cTDP level 3
  Long term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
  Range 0 to 4095875 in Step size of 125
**/
  UINT32                      Custom3PowerLimit2;

/** Offset 0x0E5C - Platform PL1 power
  Platform PL1 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range
  0 to 4095875 in Step size of 125
**/
  UINT32                      PsysPowerLimit1Power;

/** Offset 0x0E60 - Platform PL2 power
  Platform PL2 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range
  0 to 4095875 in Step size of 125
**/
  UINT32                      PsysPowerLimit2Power;

/** Offset 0x0E64 - Race To Halt
  Enable/Disable Race To Halt feature. RTH will dynamically increase CPU frequency
  in order to enter pkg C-State faster to reduce overall power. (RTH is controlled
  through MSR 1FC bit 20)Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       RaceToHalt;

/** Offset 0x0E65 - Set Three Strike Counter Disable
  False (default): Three Strike counter will be incremented and True: Prevents Three
  Strike counter from incrementing; <b>0: False</b>; 1: True.
  0: False, 1: True
**/
  UINT8                       ThreeStrikeCounterDisable;

/** Offset 0x0E66 - Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT
  Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT; <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       HwpInterruptControl;

/** Offset 0x0E67 - 5-Core Ratio Limit
  5-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused
  5-Core Ratio Limit + OC Bins.This 5-Core Ratio Limit Must be Less than or equal
  to 1-Core Ratio Limit.Range is 0 to 83
  0x0:0xFF
**/
  UINT8                       FiveCoreRatioLimit;

/** Offset 0x0E68 - 6-Core Ratio Limit
  6-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused
  6-Core Ratio Limit + OC Bins.This 6-Core Ratio Limit Must be Less than or equal
  to 1-Core Ratio Limit.Range is 0 to 83
  0x0:0xFF
**/
  UINT8                       SixCoreRatioLimit;

/** Offset 0x0E69 - 7-Core Ratio Limit
  7-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused
  7-Core Ratio Limit + OC Bins.This 7-Core Ratio Limit Must be Less than or equal
  to 1-Core Ratio Limit.Range is 0 to 83
  0x0:0xFF
**/
  UINT8                       SevenCoreRatioLimit;

/** Offset 0x0E6A - 8-Core Ratio Limit
  8-Core Ratio Limit: For XE part: LFM to 255, For overclocking part: LFM to Fused
  8-Core Ratio Limit + OC Bins.This 8-Core Ratio Limit Must be Less than or equal
  to 1-Core Ratio Limit.Range is 0 to 83
  0x0:0xFF
**/
  UINT8                       EightCoreRatioLimit;

/** Offset 0x0E6B - Intel Turbo Boost Max Technology 3.0
  Intel Turbo Boost Max Technology 3.0. 0: Disabled; <b>1: Enabled</b>
  $EN_DIS
**/
  UINT8                       EnableItbm;

/** Offset 0x0E6C - Intel Turbo Boost Max Technology 3.0 Driver
  Intel Turbo Boost Max Technology 3.0 Driver <b>0: Disabled</b>; 1: Enabled
  $EN_DIS
**/
  UINT8                       EnableItbmDriver;

/** Offset 0x0E6D - Enable or Disable C1 Cstate Demotion
  Enable or Disable C1 Cstate Demotion. Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       C1StateAutoDemotion;

/** Offset 0x0E6E - Enable or Disable C1 Cstate UnDemotion
  Enable or Disable C1 Cstate UnDemotion. Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       C1StateUnDemotion;

/** Offset 0x0E6F - Minimum Ring ratio limit override
  Minimum Ring ratio limit override. <b>0: Hardware defaults.</b> Range: 0 - Max turbo
  ratio limit
**/
  UINT8                       MinRingRatioLimit;

/** Offset 0x0E70 - Maximum Ring ratio limit override
  Maximum Ring ratio limit override. <b>0: Hardware defaults.</b> Range: 0 - Max turbo
  ratio limit
**/
  UINT8                       MaxRingRatioLimit;

/** Offset 0x0E71 - Enable or Disable Per Core P State OS control
  Enable or Disable Per Core P State OS control. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       EnablePerCorePState;

/** Offset 0x0E72 - Enable or Disable HwP Autonomous Per Core P State OS control
  Enable or Disable HwP Autonomous Per Core P State OS control. 0: Disable; <b>1:
  Enable</b>
  $EN_DIS
**/
  UINT8                       EnableHwpAutoPerCorePstate;

/** Offset 0x0E73 - Enable or Disable HwP Autonomous EPP Grouping
  Enable or Disable HwP Autonomous EPP Grouping. 0: Disable; <b>1: Enable</b>
  $EN_DIS
**/
  UINT8                       EnableHwpAutoEppGrouping;

/** Offset 0x0E74 - Enable or Disable EPB override over PECI
  Enable or Disable EPB override over PECI. <b>0: Disable;</b> 1: Enable
  $EN_DIS
**/
  UINT8                       EnableEpbPeciOverride;

/** Offset 0x0E75 - Enable or Disable Fast MSR for IA32_HWP_REQUEST
  Enable or Disable Fast MSR for IA32_HWP_REQUEST. 0: Disable;<b> 1: Enable</b>
  $EN_DIS
**/
  UINT8                       EnableFastMsrHwpReq;

/** Offset 0x0E76 - Enable Configurable TDP
  Applies TDP initialization settings based on non-cTDP or cTDP.; 0: Applies to non-cTDP;
  <b>1: Applies to cTDP</b>
  $EN_DIS
**/
  UINT8                       ApplyConfigTdp;

/** Offset 0x0E77 - ReservedCpuPostMemTest
  Reserved for CPU Post-Mem Test
  $EN_DIS
**/
  UINT8                       ReservedCpuPostMemTest[16];

/** Offset 0x0E87
**/
  UINT8                       SecurityPostMemRsvd[16];

/** Offset 0x0E97 - D0I3 Setting for HECI Disable
  Test, 0: disable, 1: enable, Setting this option disables setting D0I3 bit for all
  HECI devices
  $EN_DIS
**/
  UINT8                       DisableD0I3SettingForHeci;

/** Offset 0x0E98 - Enable LOCKDOWN SMI
  Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit.
  $EN_DIS
**/
  UINT8                       PchLockDownGlobalSmi;

/** Offset 0x0E99 - Enable LOCKDOWN BIOS Interface
  Enable BIOS Interface Lock Down bit to prevent writes to the Backup Control Register.
  $EN_DIS
**/
  UINT8                       PchLockDownBiosInterface;

/** Offset 0x0E9A - Unlock all GPIO pads
  Force all GPIO pads to be unlocked for debug purpose.
  $EN_DIS
**/
  UINT8                       PchUnlockGpioPads;

/** Offset 0x0E9B - PCH Unlock SideBand access
  The SideBand PortID mask for certain end point (e.g. PSFx) will be locked before
  3rd party code execution. 0: Lock SideBand access; 1: Unlock SideBand access.
  $EN_DIS
**/
  UINT8                       PchSbAccessUnlock;

/** Offset 0x0E9C - PCIE RP Ltr Max Snoop Latency
  Latency Tolerance Reporting, Max Snoop Latency.
**/
  UINT16                      PcieRpLtrMaxSnoopLatency[24];

/** Offset 0x0ECC - PCIE RP Ltr Max No Snoop Latency
  Latency Tolerance Reporting, Max Non-Snoop Latency.
**/
  UINT16                      PcieRpLtrMaxNoSnoopLatency[24];

/** Offset 0x0EFC - PCIE RP Snoop Latency Override Mode
  Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
  UINT8                       PcieRpSnoopLatencyOverrideMode[24];

/** Offset 0x0F14 - PCIE RP Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
  UINT8                       PcieRpSnoopLatencyOverrideMultiplier[24];

/** Offset 0x0F2C - PCIE RP Snoop Latency Override Value
  Latency Tolerance Reporting, Snoop Latency Override Value.
**/
  UINT16                      PcieRpSnoopLatencyOverrideValue[24];

/** Offset 0x0F5C - PCIE RP Non Snoop Latency Override Mode
  Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
  UINT8                       PcieRpNonSnoopLatencyOverrideMode[24];

/** Offset 0x0F74 - PCIE RP Non Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
  UINT8                       PcieRpNonSnoopLatencyOverrideMultiplier[24];

/** Offset 0x0F8C - PCIE RP Non Snoop Latency Override Value
  Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
  UINT16                      PcieRpNonSnoopLatencyOverrideValue[24];

/** Offset 0x0FBC - PCIE RP Slot Power Limit Scale
  Specifies scale used for slot power limit value. Leave as 0 to set to default.
**/
  UINT8                       PcieRpSlotPowerLimitScale[24];

/** Offset 0x0FD4 - PCIE RP Slot Power Limit Value
  Specifies upper limit on power supplie by slot. Leave as 0 to set to default.
**/
  UINT16                      PcieRpSlotPowerLimitValue[24];

/** Offset 0x1004 - PCIE RP Enable Port8xh Decode
  This member describes whether PCIE root port Port 8xh Decode is enabled. 0: Disable;
  1: Enable.
  $EN_DIS
**/
  UINT8                       PcieEnablePort8xhDecode;

/** Offset 0x1005 - PCIE Port8xh Decode Port Index
  The Index of PCIe Port that is selected for Port8xh Decode (0 Based).
**/
  UINT8                       PchPciePort8xhDecodePortIndex;

/** Offset 0x1006 - PCH Energy Reporting
  Disable/Enable PCH to CPU energy report feature.
  $EN_DIS
**/
  UINT8                       PchPmDisableEnergyReport;

/** Offset 0x1007 - PCH Sata Test Mode
  Allow entrance to the PCH SATA test modes.
  $EN_DIS
**/
  UINT8                       SataTestMode;

/** Offset 0x1008 - PCH USB OverCurrent mapping lock enable
  If this policy option is enabled then BIOS will program OCCFDONE bit in xHCI meaning
  that OC mapping data will be consumed by xHCI and OC mapping registers will be locked.
  $EN_DIS
**/
  UINT8                       PchXhciOcLock;

/** Offset 0x1009 - Low Power Mode Enable/Disable config mask
  Configure if respective S0i2/3 sub-states are to be supported. Each bit corresponds
  to one sub-state (LPMx - BITx): LPM0-s0i2.0, LPM1-s0i2.1, LPM2-s0i2.2, LPM3-s0i3.0,
  LPM4-s0i3.1, LPM5-s0i3.2, LPM6-s0i3.3, LPM7-s0i3.4.
**/
  UINT8                       PmcLpmS0ixSubStateEnableMask;

/** Offset 0x100A - Mctp Broadcast Cycle
  Test, Determine if MCTP Broadcast is enabled <b>0: Disable</b>; 1: Enable.
  $EN_DIS
**/
  UINT8                       MctpBroadcastCycle;

/** Offset 0x100B
**/
  UINT8                       UnusedUpdSpace47[1];

/** Offset 0x100C - PCIE RP Ltr Max Snoop Latency
  Latency Tolerance Reporting, Max Snoop Latency.
**/
  UINT16                      CpuPcieRpLtrMaxSnoopLatency[4];

/** Offset 0x1014 - PCIE RP Ltr Max No Snoop Latency
  Latency Tolerance Reporting, Max Non-Snoop Latency.
**/
  UINT16                      CpuPcieRpLtrMaxNoSnoopLatency[4];

/** Offset 0x101C - PCIE RP Snoop Latency Override Mode
  Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
  UINT8                       CpuPcieRpSnoopLatencyOverrideMode[4];

/** Offset 0x1020 - PCIE RP Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
  UINT8                       CpuPcieRpSnoopLatencyOverrideMultiplier[4];

/** Offset 0x1024 - PCIE RP Snoop Latency Override Value
  Latency Tolerance Reporting, Snoop Latency Override Value.
**/
  UINT16                      CpuPcieRpSnoopLatencyOverrideValue[4];

/** Offset 0x102C - PCIE RP Non Snoop Latency Override Mode
  Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
  UINT8                       CpuPcieRpNonSnoopLatencyOverrideMode[4];

/** Offset 0x1030 - PCIE RP Non Snoop Latency Override Multiplier
  Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
  UINT8                       CpuPcieRpNonSnoopLatencyOverrideMultiplier[4];

/** Offset 0x1034 - PCIE RP Non Snoop Latency Override Value
  Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
  UINT16                      CpuPcieRpNonSnoopLatencyOverrideValue[4];

/** Offset 0x103C - PCIE RP Upstream Port Transmiter Preset
  Used during Gen3 Link Equalization. Used for all lanes.  Default is 7.
**/
  UINT8                       CpuPcieRpGen3Uptp[4];

/** Offset 0x1040 - PCIE RP Downstream Port Transmiter Preset
  Used during Gen3 Link Equalization. Used for all lanes.  Default is 7.
**/
  UINT8                       CpuPcieRpGen3Dptp[4];

/** Offset 0x1044 - PCIE RP Upstream Port Transmiter Preset
  Used during Gen3 Link Equalization. Used for all lanes.  Default is 7.
**/
  UINT8                       CpuPcieRpGen4Uptp[4];

/** Offset 0x1048 - PCIE RP Downstream Port Transmiter Preset
  Used during Gen3 Link Equalization. Used for all lanes.  Default is 7.
**/
  UINT8                       CpuPcieRpGen4Dptp[4];

/** Offset 0x104C - Enable PSE JTAG debug option
  Set if to enable JTAG debug feature for PSE. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseJtagEnabled;

/** Offset 0x104D - Enable PSE JTAG pin option
  This option is used to enable or disable PSE JTAG pin pad mode. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseJtagPinMux;

/** Offset 0x104E - Enable PSE SHELL option
  Set if to enable PSE Shell feature. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseShellEnabled;

/** Offset 0x104F - Enable PSE ECLITE option
  Set if to enable PSE Eclite feature. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseEcliteEnabled;

/** Offset 0x1050 - Enable PSE OOB option
  Set if to enable PSE OOB feature. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseOobEnabled;

/** Offset 0x1051 - Enable CPU Temperature Read
  Set to enable CPU Temperature Read feature. 0: Disable; 1: Enable.
**/
  UINT8                       PchCpuTempSensorEnable;

/** Offset 0x1052 - Enable PSE WoL option
  Set if to enable PSE WoL feature. 0: Disable; 1: Enable.
**/
  UINT8                       PchPseWoLEnabled;

/** Offset 0x1053
**/
  UINT8                       ReservedFspsUpd[13];
} FSP_S_CONFIG;

/** Fsp S UPD Configuration
**/
typedef struct {

/** Offset 0x0000
**/
  FSP_UPD_HEADER              FspUpdHeader;

/** Offset 0x0020
**/
  FSP_S_CONFIG                FspsConfig;

/** Offset 0x1060
**/
  UINT8                       UnusedUpdSpace48[6];

/** Offset 0x1066
**/
  UINT16                      UpdTerminator;
} FSPS_UPD;

#pragma pack()

#endif