1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
|
/*
* This file is part of the coreboot project.
*
* Copyright (C) 2013 Damien Zammit <damien@zamaudio.com>
* Copyright (C) 2014 Edward O'Callaghan <eocallaghan@alterapraxis.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <arch/io.h>
#include <device/pnp.h>
#include <stdint.h>
#include "ite.h"
/* Global configuration registers. */
#define ITE_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define ITE_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define ITE_CONFIG_REG_CLOCKSEL 0x23 /* Clock Selection. */
#define ITE_CONFIG_REG_SWSUSP 0x24 /* Software Suspend, Flash I/F. */
#define ITE_CONFIG_REG_MFC 0x2a /* multi function pin */
#define ITE_CONFIG_REG_WATCHDOG 0x72 /* watchdog config */
/* Helper procedure */
static void ite_sio_write(device_t dev, u8 reg, u8 value)
{
pnp_set_logical_device(dev);
pnp_write_config(dev, reg, value);
}
/* Enable configuration */
static void pnp_enter_conf_state(device_t dev)
{
u16 port = dev >> 8;
outb(0x87, port);
outb(0x01, port);
outb(0x55, port);
outb((port == 0x4e) ? 0xaa : 0x55, port);
}
/* Disable configuration */
static void pnp_exit_conf_state(device_t dev)
{
ite_sio_write(dev, ITE_CONFIG_REG_CC, 0x02);
}
void ite_reg_write(device_t dev, u8 reg, u8 value)
{
pnp_enter_conf_state(dev);
ite_sio_write(dev, reg, value);
pnp_exit_conf_state(dev);
}
/*
* in romstage.c
* #define CLKIN_DEV PNP_DEV(0x2e, ITE_GPIO)
* and pass: CLKIN_DEV
* ITE_UART_CLK_PREDIVIDE_24
* ITE_UART_CLK_PREDIVIDE_48 (default)
*/
void ite_conf_clkin(device_t dev, u8 predivide)
{
ite_reg_write(dev, ITE_CONFIG_REG_CLOCKSEL, (0x1 & predivide));
}
/* Bring up early serial debugging output before the RAM is initialized. */
void ite_enable_serial(device_t dev, u16 iobase)
{
pnp_enter_conf_state(dev);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, PNP_IDX_IO0, iobase);
pnp_set_enable(dev, 1);
pnp_exit_conf_state(dev);
}
/*
*
* LDN 7, reg 0x2a - needed for S3, or memory power will be cut off
* this was documented only in IT8712F_V0.9.2!
*
* Enable 3VSBSW#. (For System Suspend-to-RAM)
* 0: 3VSBSW# will be always inactive.
* 1: 3VSBSW# enabled. It will be (NOT SUSB#) NAND SUSC#.
*
* in romstage.c
* #define GPIO_DEV PNP_DEV(0x2e, ITE_GPIO)
* and pass: GPIO_DEV
*/
void ite_enable_3vsbsw(device_t dev)
{
u8 tmp;
pnp_enter_conf_state(dev);
pnp_set_logical_device(dev);
tmp = pnp_read_config(dev, ITE_CONFIG_REG_MFC);
tmp |= 0x80;
pnp_write_config(dev, ITE_CONFIG_REG_MFC, tmp);
pnp_exit_conf_state(dev);
}
/*
* in romstage.c
* #define GPIO_DEV PNP_DEV(0x2e, ITE_GPIO)
* and pass: GPIO_DEV
*/
void ite_kill_watchdog(device_t dev)
{
pnp_enter_conf_state(dev);
ite_sio_write(dev, ITE_CONFIG_REG_WATCHDOG, 0x00);
pnp_exit_conf_state(dev);
}
|