1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <arch/cache.h>
#include <device/mmio.h>
#include <console/console.h>
#include <device/device.h>
#include <delay.h>
#include <edid.h>
#include <gpio.h>
#include <string.h>
#include <soc/addressmap.h>
#include <soc/clock.h>
#include <soc/display.h>
#include <soc/edp.h>
#include <soc/hdmi.h>
#include <soc/gpio.h>
#include <soc/grf.h>
#include <soc/soc.h>
#include <soc/vop.h>
#include "chip.h"
void rk_display_init(struct device *dev, u32 lcdbase, unsigned long fb_size)
{
struct edid edid;
uint32_t val;
struct soc_rockchip_rk3288_config *conf = dev->chip_info;
uint32_t lower = ALIGN_DOWN(lcdbase, MiB);
uint32_t upper = ALIGN_UP(lcdbase + fb_size, MiB);
enum vop_modes detected_mode = VOP_MODE_UNKNOWN;
printk(BIOS_SPEW, "LCD framebuffer @%p\n", (void *)(lcdbase));
memset((void *)lcdbase, 0, fb_size); /* clear the framebuffer */
dcache_clean_invalidate_by_mva((void *)lower, upper - lower);
mmu_config_range(lower / MiB, (upper - lower) / MiB, DCACHE_OFF);
switch (conf->vop_mode) {
case VOP_MODE_NONE:
return;
case VOP_MODE_AUTO_DETECT:
/* try EDP first, then HDMI */
case VOP_MODE_EDP:
printk(BIOS_DEBUG, "Attempting to setup EDP display.\n");
rkclk_configure_edp();
rkclk_configure_vop_aclk(conf->vop_id, 192 * MHz);
/* grf_edp_ref_clk_sel: from internal 24MHz or 27MHz clock */
write32(&rk3288_grf->soc_con12, RK_SETBITS(1 << 4));
/* select epd signal from vop0 or vop1 */
val = (conf->vop_id == 1) ? RK_SETBITS(1 << 5) :
RK_CLRBITS(1 << 5);
write32(&rk3288_grf->soc_con6, val);
rk_edp_init();
if (rk_edp_get_edid(&edid) == 0) {
detected_mode = VOP_MODE_EDP;
break;
} else {
printk(BIOS_WARNING, "Cannot get EDID from EDP.\n");
if (conf->vop_mode == VOP_MODE_EDP)
return;
}
/* fall thru */
case VOP_MODE_HDMI:
printk(BIOS_DEBUG, "Attempting to setup HDMI display.\n");
rkclk_configure_hdmi();
rkclk_configure_vop_aclk(conf->vop_id, 384 * MHz);
rk_hdmi_init(conf->vop_id);
if (rk_hdmi_get_edid(&edid) == 0) {
detected_mode = VOP_MODE_HDMI;
break;
} else {
printk(BIOS_WARNING, "Cannot get EDID from HDMI.\n");
if (conf->vop_mode == VOP_MODE_HDMI)
return;
}
/* fall thru */
default:
printk(BIOS_WARNING, "Cannot read any edid info, aborting.\n");
return;
}
if (rkclk_configure_vop_dclk(conf->vop_id, edid.mode.pixel_clock * KHz)) {
printk(BIOS_WARNING, "config vop err\n");
return;
}
edid_set_framebuffer_bits_per_pixel(&edid,
conf->framebuffer_bits_per_pixel, 0);
rkvop_mode_set(conf->vop_id, &edid, detected_mode);
rkvop_prepare(conf->vop_id, &edid);
rkvop_enable(conf->vop_id, lcdbase);
switch (detected_mode) {
case VOP_MODE_HDMI:
if (rk_hdmi_enable(&edid)) {
printk(BIOS_WARNING, "hdmi enable err\n");
return;
}
/*
* HACK: if we do remove this delay, HDMI TV may not show
* anythings. So we make an delay here, ensure TV have
* enough time to respond.
*/
mdelay(2000);
break;
case VOP_MODE_EDP:
default:
if (rk_edp_prepare()) {
printk(BIOS_WARNING, "edp prepare err\n");
return;
}
if (rk_edp_enable()) {
printk(BIOS_WARNING, "edp enable err\n");
return;
}
mainboard_power_on_backlight();
break;
}
set_vbe_mode_info_valid(&edid, (uintptr_t)lcdbase);
}
|
