1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
|
/* SPDX-License-Identifier: GPL-2.0-only */
/* This file is part of the coreboot project. */
#include <device/mmio.h>
#include <delay.h>
#include <soc/addressmap.h>
#include <soc/clk_rst.h>
#include <soc/clock.h>
#include <soc/nvidia/tegra/i2c.h>
#include <soc/padconfig.h>
#include <soc/power.h>
#define I2C6_PADCTL 0xC001
#define DPAUX_HYBRID_PADCTL 0x545C0124
#define DPAUX_HYBRID_SPARE 0x545C0134
static void enable_sor_periph_clocks(void)
{
clock_enable(CLK_L_HOST1X, 0, 0, 0, 0, CLK_X_DPAUX, 0);
/* Give clocks time to stabilize. */
udelay(IO_STABILIZATION_DELAY);
}
static void disable_sor_periph_clocks(void)
{
clock_disable(CLK_L_HOST1X, 0, 0, 0, 0, CLK_X_DPAUX, 0);
/* Give clocks time to stabilize. */
udelay(IO_STABILIZATION_DELAY);
}
static void unreset_sor_periphs(void)
{
clock_clr_reset(CLK_L_HOST1X, 0, 0, 0, 0, CLK_X_DPAUX, 0);
}
void soc_configure_i2c6pad(void)
{
/*
* I2C6 on Tegra1xx requires some special init.
* The SOR block must be unpowergated, and a couple of
* display-based peripherals must be clocked and taken
* out of reset so that a DPAUX register can be
* configured to enable the I2C6 mux routing.
* Afterwards, we can disable clocks to the display blocks
* and put Host1X back in reset. DPAUX must remain out of
* reset and the SOR partition must remained unpowergated.
*/
soc_configure_host1x();
/* enable SOR_SAFE and DPAUX_1 clocks */
clock_enable_y(CLK_Y_DPAUX1 | CLK_Y_SOR_SAFE);
/* Now we can write the I2C6 mux in DPAUX */
write32((void *)DPAUX_HYBRID_PADCTL, I2C6_PADCTL);
/* Finally, power up the pads */
write32((void *)DPAUX_HYBRID_SPARE, 0);
/*
* Delay before turning off Host1X/DPAUX clocks.
* This delay is needed to keep the sequence from
* hanging the system.
*/
udelay(CLOCK_PLL_STABLE_DELAY_US);
/* Stop Host1X/DPAUX clocks and reset Host1X */
disable_sor_periph_clocks();
clock_set_reset_l(CLK_L_HOST1X);
}
void soc_configure_host1x(void)
{
power_ungate_partition(POWER_PARTID_SOR);
/* Host1X needs a valid clock source so DPAUX can be accessed. */
clock_configure_source(host1x, PLLP, 204000);
enable_sor_periph_clocks();
remove_clamps(POWER_PARTID_SOR);
unreset_sor_periphs();
}
|
