1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <device/mmio.h>
#include <console/console.h>
#include <soc/addressmap.h>
#include <soc/usb.h>
#include <timer.h>
#define USBTAG "[SSUSB] "
#define u3p_msg(fmt, arg...) printk(BIOS_INFO, USBTAG fmt, ##arg)
#define u3p_err(fmt, arg...) printk(BIOS_ERR, USBTAG fmt, ##arg)
static struct ssusb_ippc_regs *ippc_regs = (void *)(SSUSB_IPPC_BASE);
static struct ssusb_sif_port *phy_ports = (void *)(SSUSB_SIF_BASE);
static void phy_index_power_on(int index)
{
struct ssusb_sif_port *phy = phy_ports + index;
if (!index) {
/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
setbits32(&phy->u3phya.phya_reg0, P3A_RG_U3_VUSB10_ON);
/* Disable power domain ISO */
clrbits32(&phy->u2phy.usbphyacr6, PA6_RG_U2_ISO_EN);
}
/* Switch system IP to USB mode */
clrbits32(&phy->u2phy.u2phydtm0, P2C_FORCE_UART_EN);
clrbits32(&phy->u2phy.u2phydtm1, P2C_RG_UART_EN);
if (!index)
clrbits32(&phy->u2phy.u2phyacr4, P2C_U2_GPIO_CTR_MSK);
/* Disable force settings */
clrbits32(&phy->u2phy.u2phydtm0, P2C_FORCE_SUSPENDM |
P2C_RG_XCVRSEL | P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
clrbits32(&phy->u2phy.usbphyacr6, PA6_RG_U2_BC11_SW_EN);
/* Improve Rx sensitivity */
clrsetbits32(&phy->u2phy.usbphyacr6,
PA6_RG_U2_SQTH, PA6_RG_U2_SQTH_VAL(2));
setbits32(&phy->u2phy.usbphyacr6, PA6_RG_U2_OTG_VBUSCMP_EN);
clrsetbits32(&phy->u3phya_da.reg0,
P3A_RG_XTAL_EXT_EN_U3, P3A_RG_XTAL_EXT_EN_U3_VAL(2));
clrsetbits32(&phy->u3phya.phya_reg9,
P3A_RG_RX_DAC_MUX, P3A_RG_RX_DAC_MUX_VAL(4));
if (!index)
clrbits32(&phy->u2phy.usbphyacr5, PA5_RG_U2_HS_100U_U3_EN);
clrsetbits32(&phy->u3phya.phya_reg6,
P3A_RG_TX_EIDLE_CM, P3A_RG_TX_EIDLE_CM_VAL(0xe));
clrsetbits32(&phy->u3phyd.phyd_cdr1,
P3D_RG_CDR_BIR_LTD0, P3D_RG_CDR_BIR_LTD0_VAL(0xc));
clrsetbits32(&phy->u3phyd.phyd_cdr1,
P3D_RG_CDR_BIR_LTD1, P3D_RG_CDR_BIR_LTD1_VAL(0x3));
clrsetbits32(&phy->u2phy.u2phydtm1,
P2C_RG_SESSEND, P2C_RG_VBUSVALID | P2C_RG_AVALID);
/* Set USB 2.0 slew rate value */
clrsetbits32(&phy->u2phy.usbphyacr5,
PA5_RG_U2_HSTX_SRCTRL, PA5_RG_U2_HSTX_SRCTRL_VAL(4));
/* Set USB 2.0 disconnect threshold */
clrsetbits32(&phy->u2phy.usbphyacr6,
PA6_RG_U2_DISCTH, PA6_RG_U2_DISCTH_VAL(15));
}
static void u3phy_power_on(void)
{
for (int i = 0; i < USB_PORT_NUMBER; i++)
phy_index_power_on(i);
}
static int check_ip_clk_status(void)
{
int u3_port_num;
u32 check_bits;
u32 sts1, sts2;
struct stopwatch sw;
u3_port_num = CAP_U3_PORT_NUM(read32(&ippc_regs->ip_xhci_cap));
check_bits = STS1_SYSPLL_STABLE | STS1_REF_RST | STS1_SYS125_RST;
check_bits |= (u3_port_num ? STS1_U3_MAC_RST : 0);
stopwatch_init_usecs_expire(&sw, 50000);
do {
if (stopwatch_expired(&sw)) {
u3p_err("USB clocks are not stable!!!\n");
return -1;
}
sts1 = read32(&ippc_regs->ip_pw_sts1) & check_bits;
sts2 = read32(&ippc_regs->ip_pw_sts2) & STS2_U2_MAC_RST;
} while ((sts1 != check_bits) || !sts2);
return 0;
}
static int u3phy_ports_enable(void)
{
int i;
u32 value;
int u3_port_num;
int u2_port_num;
value = read32(&ippc_regs->ip_xhci_cap);
u3_port_num = CAP_U3_PORT_NUM(value);
u2_port_num = CAP_U2_PORT_NUM(value);
u3p_msg("%s u2p:%d, u3p:%d\n", __func__, u2_port_num, u3_port_num);
/* Power on host ip */
clrbits32(&ippc_regs->ip_pw_ctr1, CTRL1_IP_HOST_PDN);
/* Power on and enable all u3 ports */
for (i = 0; i < u3_port_num; i++) {
clrsetbits32(&ippc_regs->u3_ctrl_p[i],
CTRL_U3_PORT_PDN | CTRL_U3_PORT_DIS,
CTRL_U3_PORT_HOST_SEL);
}
/* Power on and enable all u2 ports */
for (i = 0; i < u2_port_num; i++) {
clrsetbits32(&ippc_regs->u2_ctrl_p[i],
CTRL_U2_PORT_PDN | CTRL_U2_PORT_DIS,
CTRL_U2_PORT_HOST_SEL);
}
return check_ip_clk_status();
}
static inline void ssusb_soft_reset(void)
{
/* Reset whole ip */
setbits32(&ippc_regs->ip_pw_ctr0, CTRL0_IP_SW_RST);
clrbits32(&ippc_regs->ip_pw_ctr0, CTRL0_IP_SW_RST);
}
__weak void mtk_usb_prepare(void)
{
/* do nothing */
}
__weak void mtk_usb_adjust_phy_shift(void)
{
/* do nothing */
}
void setup_usb_host(void)
{
u3p_msg("Setting up USB HOST controller...\n");
mtk_usb_prepare();
ssusb_soft_reset();
if (u3phy_ports_enable()) {
u3p_err("%s fail to enable ports\n", __func__);
return;
}
u3phy_power_on();
mtk_usb_adjust_phy_shift();
u3p_msg("phy power-on done.\n");
}
|
