blob: 5f8fed9a56f6b2801980d7b7188c42d6affba200 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
|
/*
* This file is part of the coreboot project.
*
* Copyright (C) 2015 Intel Corp.
* (Written by Alexandru Gagniuc <alexandrux.gagniuc@intel.com> for Intel Corp.)
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#ifndef _SOC_APOLLOLAKE_CHIP_H_
#define _SOC_APOLLOLAKE_CHIP_H_
#include <soc/gpe.h>
#include <soc/gpio_defs.h>
#include <soc/gpio.h>
#include <soc/intel/common/lpss_i2c.h>
#include <device/i2c.h>
#include <soc/pm.h>
#define CLKREQ_DISABLED 0xf
#define APOLLOLAKE_I2C_DEV_MAX 8
/* Serial IRQ control. SERIRQ_QUIET is the default (0). */
enum serirq_mode {
SERIRQ_QUIET,
SERIRQ_CONTINUOUS,
SERIRQ_OFF,
};
struct soc_intel_apollolake_config {
/*
* Mapping from PCIe root port to CLKREQ input on the SOC. The SOC has
* four CLKREQ inputs, but six root ports. Root ports without an
* associated CLKREQ signal must be marked with "CLKREQ_DISABLED"
*/
uint8_t pcie_rp0_clkreq_pin;
uint8_t pcie_rp1_clkreq_pin;
uint8_t pcie_rp2_clkreq_pin;
uint8_t pcie_rp3_clkreq_pin;
uint8_t pcie_rp4_clkreq_pin;
uint8_t pcie_rp5_clkreq_pin;
/* [14:8] DDR mode Number of dealy elements.Each = 125pSec.
* [6:0] SDR mode Number of dealy elements.Each = 125pSec.
*/
uint32_t emmc_tx_cmd_cntl;
/* [14:8] HS400 mode Number of dealy elements.Each = 125pSec.
* [6:0] SDR104/HS200 mode Number of dealy elements.Each = 125pSec.
*/
uint32_t emmc_tx_data_cntl1;
/* [30:24] SDR50 mode Number of dealy elements.Each = 125pSec.
* [22:16] DDR50 mode Number of dealy elements.Each = 125pSec.
* [14:8] SDR25/HS50 mode Number of dealy elements.Each = 125pSec.
* [6:0] SDR12/Compatibility mode Number of dealy elements.Each = 125pSec.
*/
uint32_t emmc_tx_data_cntl2;
/* [30:24] SDR50 mode Number of dealy elements.Each = 125pSec.
* [22:16] DDR50 mode Number of dealy elements.Each = 125pSec.
* [14:8] SDR25/HS50 mode Number of dealy elements.Each = 125pSec.
* [6:0] SDR12/Compatibility mode Number of dealy elements.Each = 125pSec.
*/
uint32_t emmc_rx_cmd_data_cntl1;
/* [14:8] HS400 mode 1 Number of dealy elements.Each = 125pSec.
* [6:0] HS400 mode 2 Number of dealy elements.Each = 125pSec.
*/
uint32_t emmc_rx_strobe_cntl;
/* [13:8] Auto Tuning mode Number of dealy elements.Each = 125pSec.
* [6:0] SDR104/HS200 Number of dealy elements.Each = 125pSec.
*/
uint32_t emmc_rx_cmd_data_cntl2;
/* Configure serial IRQ (SERIRQ) line. */
enum serirq_mode serirq_mode;
/* I2C bus configuration */
struct lpss_i2c_bus_config i2c[APOLLOLAKE_I2C_DEV_MAX];
uint8_t gpe0_dw1; /* GPE0_63_32 STS/EN */
uint8_t gpe0_dw2; /* GPE0_95_64 STS/EN */
uint8_t gpe0_dw3; /* GPE0_127_96 STS/EN */
/* Configure LPSS S0ix Enable */
uint8_t lpss_s0ix_enable;
/* Enable DPTF support */
int dptf_enable;
/* PL1 override value in mW for APL */
uint16_t tdp_pl1_override_mw;
/* PL2 override value in mW for APL */
uint16_t tdp_pl2_override_mw;
/* Configure Audio clk gate and power gate
* IOSF-SB port ID 92 offset 0x530 [5] and [3]
*/
uint8_t hdaudio_clk_gate_enable;
uint8_t hdaudio_pwr_gate_enable;
uint8_t hdaudio_bios_config_lockdown;
/* SLP S3 minimum assertion width. */
int slp_s3_assertion_width_usecs;
/* GPIO pin for PERST_0 */
uint16_t prt0_gpio;
};
#endif /* _SOC_APOLLOLAKE_CHIP_H_ */
|
