1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
|
static void setup_coherent_ht_domain(void)
{
static const unsigned int register_values[] = {
/* Routing Table Node i
* F0:0x40 i = 0,
* F0:0x44 i = 1,
* F0:0x48 i = 2,
* F0:0x4c i = 3,
* F0:0x50 i = 4,
* F0:0x54 i = 5,
* F0:0x58 i = 6,
* F0:0x5c i = 7
* [ 0: 3] Request Route
* [0] Route to this node
* [1] Route to Link 0
* [2] Route to Link 1
* [3] Route to Link 2
* [11: 8] Response Route
* [0] Route to this node
* [1] Route to Link 0
* [2] Route to Link 1
* [3] Route to Link 2
* [19:16] Broadcast route
* [0] Route to this node
* [1] Route to Link 0
* [2] Route to Link 1
* [3] Route to Link 2
*/
PCI_ADDR(0, 0x18, 0, 0x40), 0xfff0f0f0, 0x00010101,
PCI_ADDR(0, 0x18, 0, 0x44), 0xfff0f0f0, 0x00010101,
PCI_ADDR(0, 0x18, 0, 0x48), 0xfff0f0f0, 0x00010101,
PCI_ADDR(0, 0x18, 0, 0x4c), 0xfff0f0f0, 0x00010101,
PCI_ADDR(0, 0x18, 0, 0x50), 0xfff0f0f0, 0x00010101,
PCI_ADDR(0, 0x18, 0, 0x54), 0xfff0f0f0, 0x00010101,
PCI_ADDR(0, 0x18, 0, 0x58), 0xfff0f0f0, 0x00010101,
PCI_ADDR(0, 0x18, 0, 0x5c), 0xfff0f0f0, 0x00010101,
/* Hypetransport Transaction Control Register
* F0:0x68
* [ 0: 0] Disable read byte probe
* 0 = Probes issues
* 1 = Probes not issued
* [ 1: 1] Disable Read Doubleword probe
* 0 = Probes issued
* 1 = Probes not issued
* [ 2: 2] Disable write byte probes
* 0 = Probes issued
* 1 = Probes not issued
* [ 3: 3] Disable Write Doubleword Probes
* 0 = Probes issued
* 1 = Probes not issued.
* [ 4: 4] Disable Memroy Controller Target Start
* 0 = TgtStart packets are generated
* 1 = TgtStart packets are not generated.
* [ 5: 5] CPU1 Enable
* 0 = Second CPU disabled or not present
* 1 = Second CPU enabled.
* [ 6: 6] CPU Request PassPW
* 0 = CPU requests do not pass posted writes
* 1 = CPU requests pass posted writes.
* [ 7: 7] CPU read Respons PassPW
* 0 = CPU Responses do not pass posted writes
* 1 = CPU responses pass posted writes.
* [ 8: 8] Disable Probe Memory Cancel
* 0 = Probes may generate MemCancels
* 1 = Probes may not generate MemCancels
* [ 9: 9] Disable Remote Probe Memory Cancel.
* 0 = Probes hitting dirty blocks generate memory cancel packets
* 1 = Only probed caches on the same node as the memory controller
* generate cancel packets.
* [10:10] Disable Fill Probe
* 0 = Probes issued for cache fills
* 1 = Probes not issued for cache fills.
* [11:11] Response PassPw
* 0 = Downstream response PassPW based on original request
* 1 = Downstream response PassPW set to 1
* [12:12] Change ISOC to Ordered
* 0 = Bit 1 of coherent HT RdSz/WrSz command used for iosynchronous prioritization
* 1 = Bit 1 of coherent HT RdSz/WrSz command used for ordering.
* [14:13] Buffer Release Priority select
* 00 = 64
* 01 = 16
* 10 = 8
* 11 = 2
* [15:15] Limit Coherent HT Configuration Space Range
* 0 = No coherent HT configuration space restrictions
* 1 = Limit coherent HT configuration space based on node count
* [16:16] Local Interrupt Conversion Enable.
* 0 = ExtInt/NMI interrups unaffected.
* 1 = ExtInt/NMI broadcat interrupts converted to LINT0/1
* [17:17] APIC Extended Broadcast Enable.
* 0 = APIC broadcast is 0F
* 1 = APIC broadcast is FF
* [18:18] APIC Extended ID Enable
* 0 = APIC ID is 4 bits.
* 1 = APIC ID is 8 bits.
* [19:19] APIC Extended Spurious Vector Enable
* 0 = Lower 4 bits of spurious vector are read-only 1111
* 1 = Lower 4 bits of spurious vecotr are writeable.
* [20:20] Sequence ID Source Node Enable
* 0 = Normal operation
* 1 = Keep SeqID on routed packets for debugging.
* [22:21] Downstream non-posted request limit
* 00 = No limit
* 01 = Limited to 1
* 10 = Limited to 4
* 11 = Limited to 8
* [23:23] RESERVED
* [25:24] Medium-Priority Bypass Count
* - Maximum # of times a medium priority access can pass a low
* priority access before Medium-Priority mode is disabled for one access.
* [27:26] High-Priority Bypass Count
* - Maximum # of times a high prioirty access can pass a medium or low
* priority access before High-prioirty mode is disabled for one access.
* [28:28] Enable High Priority CPU Reads
* 0 = Cpu reads are medium prioirty
* 1 = Cpu reads are high prioirty
* [29:29] Disable Low Priority Writes
* 0 = Non-isochronous writes are low priority
* 1 = Non-isochronous writes are medium prioirty
* [30:30] Disable High Priority Isochronous writes
* 0 = Isochronous writes are high priority
* 1 = Isochronous writes are medium priority
* [31:31] Disable Medium Priority Isochronous writes
* 0 = Isochronous writes are medium are high
* 1 = With bit 30 set makes Isochrouns writes low priority.
*/
PCI_ADDR(0, 0x18, 0, 0x68), 0x00800000, 0x0f00840f,
/* HT Initialization Control Register
* F0:0x6C
* [ 0: 0] Routing Table Disable
* 0 = Packets are routed according to routing tables
* 1 = Packets are routed according to the default link field
* [ 1: 1] Request Disable (BSP should clear this)
* 0 = Request packets may be generated
* 1 = Request packets may not be generated.
* [ 3: 2] Default Link (Read-only)
* 00 = LDT0
* 01 = LDT1
* 10 = LDT2
* 11 = CPU on same node
* [ 4: 4] Cold Reset
* - Scratch bit cleared by a cold reset
* [ 5: 5] BIOS Reset Detect
* - Scratch bit cleared by a cold reset
* [ 6: 6] INIT Detect
* - Scratch bit cleared by a warm or cold reset not by an INIT
*
*/
PCI_ADDR(0, 0x18, 0, 0x6C), 0xffffff8c, 0x00000000 | (1 << 6) |(1 << 5)| (1 << 4),
/* LDTi Capabilities Registers
* F0:0x80 i = 0,
* F0:0xA0 i = 1,
* F0:0xC0 i = 2,
*/
/* LDTi Link Control Registrs
* F0:0x84 i = 0,
* F0:0xA4 i = 1,
* F0:0xC4 i = 2,
* [ 1: 1] CRC Flood Enable
* 0 = Do not generate sync packets on CRC error
* 1 = Generate sync packets on CRC error
* [ 2: 2] CRC Start Test (Read-Only)
* [ 3: 3] CRC Force Frame Error
* 0 = Do not generate bad CRC
* 1 = Generate bad CRC
* [ 4: 4] Link Failure
* 0 = No link failure detected
* 1 = Link failure detected
* [ 5: 5] Initialization Complete
* 0 = Initialization not complete
* 1 = Initialization complete
* [ 6: 6] Receiver off
* 0 = Recevier on
* 1 = Receiver off
* [ 7: 7] Transmitter Off
* 0 = Transmitter on
* 1 = Transmitter off
* [ 9: 8] CRC_Error
* 00 = No error
* [0] = 1 Error on byte lane 0
* [1] = 1 Error on byte lane 1
* [12:12] Isochrnous Enable (Read-Only)
* [13:13] HT Stop Tristate Enable
* 0 = Driven during an LDTSTOP_L
* 1 = Tristated during and LDTSTOP_L
* [14:14] Extended CTL Time
* 0 = CTL is asserted for 16 bit times during link initialization
* 1 = CTL is asserted for 50us during link initialization
* [18:16] Max Link Width In (Read-Only?)
* 000 = 8 bit link
* 001 = 16bit link
* [19:19] Doubleword Flow Control in (Read-Only)
* 0 = This link does not support doubleword flow control
* 1 = This link supports doubleword flow control
* [22:20] Max Link Width Out (Read-Only?)
* 000 = 8 bit link
* 001 = 16bit link
* [23:23] Doubleworld Flow Control out (Read-Only)
* 0 = This link does not support doubleword flow control
* 1 = This link supports doubleworkd flow control
* [26:24] Link Width In
* 000 = Use 8 bits
* 001 = Use 16 bits
* 010 = reserved
* 011 = Use 32 bits
* 100 = Use 2 bits
* 101 = Use 4 bits
* 110 = reserved
* 111 = Link physically not connected
* [27:27] Doubleword Flow Control In Enable
* 0 = Doubleword flow control disabled
* 1 = Doubleword flow control enabled (Not currently supported)
* [30:28] Link Width Out
* 000 = Use 8 bits
* 001 = Use 16 bits
* 010 = reserved
* 011 = Use 32 bits
* 100 = Use 2 bits
* 101 = Use 4 bits
* 110 = reserved
* 111 = Link physically not connected
* [31:31] Doubleworld Flow Control Out Enable
* 0 = Doubleworld flow control disabled
* 1 = Doubleword flow control enabled (Not currently supported)
*/
PCI_ADDR(0, 0x18, 0, 0x84), 0x00009c05, 0x11110020,
/* LDTi Frequency/Revision Registers
* F0:0x88 i = 0,
* F0:0xA8 i = 1,
* F0:0xC8 i = 2,
* [ 4: 0] Minor Revision
* Contains the HT Minor revision
* [ 7: 5] Major Revision
* Contains the HT Major revision
* [11: 8] Link Frequency (Takes effect the next time the link is reconnected)
* 0000 = 200Mhz
* 0001 = reserved
* 0010 = 400Mhz
* 0011 = reserved
* 0100 = 600Mhz
* 0101 = 800Mhz
* 0110 = 1000Mhz
* 0111 = reserved
* 1000 = reserved
* 1001 = reserved
* 1010 = reserved
* 1011 = reserved
* 1100 = reserved
* 1101 = reserved
* 1110 = reserved
* 1111 = 100 Mhz
* [15:12] Error (Not currently Implemented)
* [31:16] Indicates the frequency capabilities of the link
* [16] = 1 encoding 0000 of freq supported
* [17] = 1 encoding 0001 of freq supported
* [18] = 1 encoding 0010 of freq supported
* [19] = 1 encoding 0011 of freq supported
* [20] = 1 encoding 0100 of freq supported
* [21] = 1 encoding 0101 of freq supported
* [22] = 1 encoding 0110 of freq supported
* [23] = 1 encoding 0111 of freq supported
* [24] = 1 encoding 1000 of freq supported
* [25] = 1 encoding 1001 of freq supported
* [26] = 1 encoding 1010 of freq supported
* [27] = 1 encoding 1011 of freq supported
* [28] = 1 encoding 1100 of freq supported
* [29] = 1 encoding 1101 of freq supported
* [30] = 1 encoding 1110 of freq supported
* [31] = 1 encoding 1111 of freq supported
*/
PCI_ADDR(0, 0x18, 0, 0x88), 0xfffff0ff, 0x00000200,
/* LDTi Feature Capability
* F0:0x8C i = 0,
* F0:0xAC i = 1,
* F0:0xCC i = 2,
*/
/* LDTi Buffer Count Registers
* F0:0x90 i = 0,
* F0:0xB0 i = 1,
* F0:0xD0 i = 2,
*/
/* LDTi Bus Number Registers
* F0:0x94 i = 0,
* F0:0xB4 i = 1,
* F0:0xD4 i = 2,
* For NonCoherent HT specifies the bus number downstream (behind the host bridge)
* [ 0: 7] Primary Bus Number
* [15: 8] Secondary Bus Number
* [23:15] Subordiante Bus Number
* [31:24] reserved
*/
PCI_ADDR(0, 0x18, 0, 0x94), 0xff000000, 0x00ff0000,
/* LDTi Type Registers
* F0:0x98 i = 0,
* F0:0xB8 i = 1,
* F0:0xD8 i = 2,
*/
};
int i;
int max;
print_debug("setting up coherent ht domain....\r\n");
max = sizeof(register_values)/sizeof(register_values[0]);
for(i = 0; i < max; i += 3) {
device_t dev;
unsigned where;
unsigned long reg;
#if 0
print_debug_hex32(register_values[i]);
print_debug(" <-");
print_debug_hex32(register_values[i+2]);
print_debug("\r\n");
#endif
dev = register_values[i] & ~0xff;
where = register_values[i] & 0xff;
reg = pci_read_config32(dev, where);
reg &= register_values[i+1];
reg |= register_values[i+2];
pci_write_config32(dev, where, reg);
#if 0
reg = pci_read_config32(register_values[i]);
reg &= register_values[i+1];
reg |= register_values[i+2] & ~register_values[i+1];
pci_write_config32(register_values[i], reg);
#endif
}
print_debug("done.\r\n");
}
|
