1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
|
/*
* This file is part of the LinuxBIOS project.
*
* Copyright (C) 2005 Tyan
* (Written by Yinghai Lu <yhlu@tyan.com> for Tyan)
* Copyright (C) 2007 Ward Vandewege <ward@gnu.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <device/device.h>
#include <console/console.h>
#include <device/smbus.h>
#include "chip.h"
/**
* Do some S2881-specific HWM initialization for the ADT7463 chip.
*
* See Analog Devices ADT7463 datasheet, Rev C (2004):
* http://www.analog.com/en/prod/0,,766_825_ADT7463,00.html
*/
static void adt7463_init(device_t dev)
{
device_t smbus_dev, adt7463;
struct device_path path;
int result;
/* Find the SMBus controller (AMD-8111). */
smbus_dev = dev_find_device(0x1022, 0x746b, 0);
if (!smbus_dev)
die("SMBus controller not found\n");
printk_debug("SMBus controller found\n");
/* Find the ADT7463 device. */
path.type = DEVICE_PATH_I2C;
path.u.i2c.device = 0x2d;
adt7463 = find_dev_path(smbus_dev->link, &path);
if (!adt7463)
die("ADT7463 not found\n");
printk_debug("ADT7463 found\n");
/* Set all fans to 'Fastest Speed Calculated by All 3 Temperature
* Channels Controls PWMx'.
*/
result = smbus_write_byte(adt7463, 0x5c, 0xc2);
result = smbus_write_byte(adt7463, 0x5d, 0xc2);
result = smbus_write_byte(adt7463, 0x5e, 0xc2);
/* Make sure that our fans never stop when temp. falls below Tmin,
* but rather keep going at minimum duty cycle (applies to automatic
* fan control mode only).
*/
result = smbus_write_byte(adt7463, 0x62, 0xc0);
/* Set minimum PWM duty cycle to 25%, rather than the default 50%. */
result = smbus_write_byte(adt7463, 0x64, 0x40);
result = smbus_write_byte(adt7463, 0x65, 0x40);
result = smbus_write_byte(adt7463, 0x66, 0x40);
/* Set Tmin to 55C, rather than the default 90C. Above this temperature
* the fans will start blowing harder as temperature increases
* (automatic mode only).
*/
result = smbus_write_byte(adt7463, 0x67, 0x37);
result = smbus_write_byte(adt7463, 0x68, 0x37);
result = smbus_write_byte(adt7463, 0x69, 0x37);
/* Set THERM limit to 70C, rather than the default 100C.
* The fans will kick in at 100% if the sensors reach this temperature,
* (only in automatic mode, but supposedly even when hardware is
* locked up). This is a failsafe measure.
*/
result = smbus_write_byte(adt7463, 0x6a, 0x46);
result = smbus_write_byte(adt7463, 0x6b, 0x46);
result = smbus_write_byte(adt7463, 0x6c, 0x46);
/* Remote temperature 1 offset (LSB == 0.25C). */
result = smbus_write_byte(adt7463, 0x70, 0x02);
/* Remote temperature 2 offset (LSB == 0.25C). */
result = smbus_write_byte(adt7463, 0x72, 0x01);
/* Set TACH measurements to normal (1/second). */
result = smbus_write_byte(adt7463, 0x78, 0xf0);
printk_debug("ADT7463 properly initialized\n");
}
static void dummy_noop(device_t dummy)
{
}
static struct device_operations dummy_operations = {
.read_resources = dummy_noop,
.set_resources = dummy_noop,
.enable_resources = dummy_noop,
.init = adt7463_init,
};
static unsigned int scan_root_bus(device_t root, unsigned int max)
{
struct device_path path;
device_t dummy;
unsigned link_i;
max = root_dev_scan_bus(root, max);
printk_debug("scan_root_bus ok\n");
/* The following is a little silly. We need a hook into the boot
* process *after* the ADT7463 device has been initialized. So we
* create this dummy device, and we put the ADT7463 S2881 specific
* settings in its init function, which gets called
* as the last device to be initialized.
*/
link_i = root->links;
if (link_i >= MAX_LINKS) {
printk_debug("Reached MAX_LINKS, not configuring ADT7463");
return max;
}
root->link[link_i].link = link_i;
root->link[link_i].dev = root;
root->link[link_i].children = 0;
root->links++;
path.type = DEVICE_PATH_PNP;
path.u.pnp.port = 0;
path.u.pnp.device = 0;
dummy = alloc_dev(&root->link[link_i], &path);
dummy->ops = &dummy_operations;
return max;
}
static struct device_operations mainboard_operations = {
.read_resources = root_dev_read_resources,
.set_resources = root_dev_set_resources,
.enable_resources = root_dev_enable_resources,
.init = root_dev_init,
.scan_bus = scan_root_bus,
};
static void enable_dev(struct device *dev)
{
dev->ops = &mainboard_operations;
}
#if CONFIG_CHIP_NAME == 1
struct chip_operations mainboard_tyan_s2881_ops = {
CHIP_NAME("Tyan S2881 Mainboard")
.enable_dev = enable_dev,
};
#endif
|
