1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <bootblock_common.h>
#include <device/pci_def.h>
#include <device/pci_ops.h>
#include <device/pnp_ops.h>
#include <intelblocks/pcr.h>
#include <soc/pci_devs.h>
#include <soc/pcr_ids.h>
#include <superio/aspeed/ast2400/ast2400.h>
#include <superio/aspeed/common/aspeed.h>
#include <tp_pch_gpio.h>
/* these are defined in intelblocks/lpc_lib.h but we can't use them yet */
#define PCR_DMI_LPCIOD 0x2770
#define PCR_DMI_LPCIOE 0x2774
#define ASPEED_CONFIG_INDEX 0x2E
#define ASPEED_CONFIG_DATA 0x2F
static void enable_espi_lpc_io_windows(void)
{
/*
* Set up decoding windows on PCH over PCR. The CPUs use two of AST2500 SIO ports,
* one is connected to debug header (SUART1) and another is used as SOL (SUART2).
* For that end it is wired into BMC virtual port.
*/
/* Open IO windows: 0x3f8 for com1 and 02e8 for com2 */
pcr_or32(PID_DMI, PCR_DMI_LPCIOD, (0 << 0) | (1 << 4));
/* LPC I/O enable: com1 and com2 */
pcr_or32(PID_DMI, PCR_DMI_LPCIOE, (1 << 0) | (1 << 1));
/* Enable com1 (0x3f8), com2 (02f8) and superio (0x2e) */
pci_mmio_write_config32(PCH_DEV_LPC, 0x80,
(1 << 28) | (1 << 16) | (1 << 17) | (0 << 0) | (1 << 4));
}
static uint8_t com_to_ast_sio(uint8_t com)
{
switch (com) {
case 0:
return AST2400_SUART1;
case 1:
return AST2400_SUART2;
case 2:
return AST2400_SUART3;
case 4:
return AST2400_SUART4;
default:
return AST2400_SUART1;
}
}
void bootblock_mainboard_early_init(void)
{
/* pre-configure Lewisburg PCH GPIO pads */
gpio_configure_pads(gpio_table, ARRAY_SIZE(gpio_table));
/* Open IO windows */
enable_espi_lpc_io_windows();
/* Configure appropriate physical port of SuperIO chip off BMC */
const pnp_devfn_t serial_dev = PNP_DEV(ASPEED_CONFIG_INDEX,
com_to_ast_sio(CONFIG_UART_FOR_CONSOLE));
aspeed_enable_serial(serial_dev, CONFIG_TTYS0_BASE);
/* Port 80h direct to GPIO for LED display */
const pnp_devfn_t gpio_dev = PNP_DEV(ASPEED_CONFIG_INDEX, AST2400_GPIO);
aspeed_enable_port80_direct_gpio(gpio_dev, GPIOH);
/* Enable UART function pin */
aspeed_enable_uart_pin(serial_dev);
}
|
