1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
|
/*
* This file is part of the coreboot project.
*
* Copyright 2014 Google Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <arch/io.h>
#include <console/console.h>
#include <device/i2c.h>
#include <soc/addressmap.h>
#include <soc/bootblock.h>
#include <soc/clock.h>
#include <soc/padconfig.h>
#include <soc/nvidia/tegra/i2c.h>
#include <soc/nvidia/tegra132/clk_rst.h>
#include <soc/nvidia/tegra132/spi.h> /* FIXME: move back to soc code? */
#include "pmic.h"
static struct clk_rst_ctlr *clk_rst = (void *)TEGRA_CLK_RST_BASE;
static const struct pad_config uart_console_pads[] = {
/* UARTA: tx and rx. */
PAD_CFG_SFIO(KB_ROW9, PINMUX_PULL_NONE, UA3),
PAD_CFG_SFIO(KB_ROW10, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, UA3),
/*
* Disable UART2 pads as they are default connected to UARTA controller.
*/
PAD_CFG_UNUSED(UART2_RXD),
PAD_CFG_UNUSED(UART2_TXD),
PAD_CFG_UNUSED(UART2_RTS_N),
PAD_CFG_UNUSED(UART2_CTS_N),
};
void bootblock_mainboard_early_init(void)
{
soc_configure_pads(uart_console_pads, ARRAY_SIZE(uart_console_pads));
}
static void set_clock_sources(void)
{
/* UARTA gets PLLP, deactivate CLK_UART_DIV_OVERRIDE */
writel(PLLP << CLK_SOURCE_SHIFT, &clk_rst->clk_src_uarta);
clock_configure_source(mselect, PLLP, 102000);
/* The PMIC is on I2C5 and can run at 400 KHz. */
clock_configure_i2c_scl_freq(i2c5, PLLP, 400);
/* TODO: We should be able to set this to 50MHz, but that did not seem
* reliable. */
clock_configure_source(sbc4, PLLP, 33333);
}
static const struct pad_config padcfgs[] = {
/* Board build id bits 1:0 */
PAD_CFG_GPIO_INPUT(KB_COL4, PINMUX_PULL_NONE),
PAD_CFG_GPIO_INPUT(KB_COL3, PINMUX_PULL_NONE),
/* PMIC i2C bus */
PAD_CFG_SFIO(PWR_I2C_SCL, PINMUX_INPUT_ENABLE, I2CPMU),
PAD_CFG_SFIO(PWR_I2C_SDA, PINMUX_INPUT_ENABLE, I2CPMU),
/* SPI fLash: mosi, miso, clk, cs0 */
PAD_CFG_SFIO(GPIO_PG6, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SPI4),
PAD_CFG_SFIO(GPIO_PG7, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SPI4),
PAD_CFG_SFIO(GPIO_PG5, PINMUX_INPUT_ENABLE, SPI4),
PAD_CFG_SFIO(GPIO_PI3, PINMUX_INPUT_ENABLE, SPI4),
};
void bootblock_mainboard_init(void)
{
set_clock_sources();
/* Enable PMIC I2C controller. */
clock_enable_clear_reset(0, CLK_H_I2C5, 0, 0, 0, 0);
/* Set up the pads required to load romstage. */
soc_configure_pads(padcfgs, ARRAY_SIZE(padcfgs));
i2c_init(4);
pmic_init(4);
tegra_spi_init(4);
}
|