blob: 5e68d3720ced3160cb2ad4bc36b065484b31bc1c (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
|
chip soc/intel/apollolake
device cpu_cluster 0 on
device lapic 0 on end
end
register "pcie_rp4_clkreq_pin" = "0" # wifi/bt
# EMMC TX DATA Delay 1#
# 0x0C[14:8] stands for 12*125 = 1500 pSec delay for HS400
# 0x11[6:0] stands for 17*125 = 2125 pSec delay for SDR104/HS200
register "emmc_tx_data_cntl1" = "0x0C11" # HS400 required
# EMMC TX DATA Delay 2#
# 0x00[30:24] stands for 0*125 = no delay for SDR50
# 0x2B[22:16] stands for 43*125 = 5375 pSec delay for DDR50
# 0x29[14:8] stands for 41*125 = 5125 pSec delay for SDR25/HS50
# 0x29[6:0] stands for 41*125 = 5125 pSec delay for SDR12
register "emmc_tx_data_cntl2" = "0x002B2929"
# EMMC RX CMD/DATA Delay 1#
# 0x00[30:24] stands for 0*125 = no delay for SDR50
# 0x12[22:16] stands for 18*125 = 2250 pSec delay for DDR50
# 0x57[14:8] stands for 87*125 = 10875 pSec delay for SDR25/HS50
# 0x3B[6:0] stands for 59*125= 7375 pSec delay for SDR12
register "emmc_rx_cmd_data_cntl1" = "0x0012573B"
# EMMC RX CMD/DATA Delay 2#
# 0x01[17:16] stands for Rx Clock before Output Buffer
# 0x00[14:8] stands for 0 delay for Auto Tuning Mode
# 0x1C[6:0] stands for 28*125 = 3500 pSec delay for HS200
register "emmc_rx_cmd_data_cntl2" = "0x1001C"
# Enable DPTF
register "dptf_enable" = "1"
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route, i.e., if this route changes then the affected GPE
# offset bits also need to be changed. This sets the PMC register
# GPE_CFG fields.
register "gpe0_dw1" = "PMC_GPE_N_31_0"
register "gpe0_dw2" = "PMC_GPE_N_63_32"
register "gpe0_dw3" = "PMC_GPE_SW_31_0"
device domain 0 on
device pci 00.0 on end # - Host Bridge
device pci 00.1 on end # - DPTF
device pci 00.2 on end # - NPK
device pci 02.0 on end # - Gen
device pci 03.0 on end # - Iunit
device pci 0d.0 on end # - P2SB
device pci 0d.1 on end # - PMC
device pci 0d.2 on end # - SPI
device pci 0d.3 on end # - Shared SRAM
device pci 0e.0 on # - Audio
chip drivers/generic/max98357a
register "sdmode_gpio" = "ACPI_GPIO_OUTPUT(GPIO_76)"
device generic 0 on end
end
end
device pci 11.0 off end # - ISH
device pci 12.0 off end # - SATA
device pci 13.0 off end # - Root Port 2 - PCIe-A 0
device pci 13.1 off end # - Root Port 3 - PCIe-A 1
device pci 13.2 off end # - Root Port 4 - PCIe-A 2
device pci 13.3 off end # - Root Port 5 - PCIe-A 3
device pci 14.0 on end # - Root Port 0 - PCIe-B 0 - Wifi
device pci 14.1 off end # - Root Port 1 - PCIe-B 1
device pci 15.0 on end # - XHCI
device pci 15.1 off end # - XDCI
device pci 16.0 on # - I2C 0
chip drivers/i2c/da7219
register "irq" = "IRQ_LEVEL_LOW(GPIO_116_IRQ)"
register "btn_cfg" = "50"
register "mic_det_thr" = "500"
register "jack_ins_deb" = "20"
register "jack_det_rate" = ""32ms_64ms""
register "jack_rem_deb" = "1"
register "a_d_btn_thr" = "0xa"
register "d_b_btn_thr" = "0x16"
register "b_c_btn_thr" = "0x21"
register "c_mic_btn_thr" = "0x3e"
register "btn_avg" = "4"
register "adc_1bit_rpt" = "1"
register "micbias_lvl" = "2600"
register "mic_amp_in_sel" = ""diff""
device i2c 1a on end
end
end
device pci 16.1 on end # - I2C 1
device pci 16.2 on end # - I2C 2
device pci 16.3 on
chip drivers/i2c/generic
register "hid" = ""ELAN0001""
register "desc" = ""ELAN Touchscreen""
register "irq" = "IRQ_EDGE_LOW(GPIO_21_IRQ)"
device i2c 10 on end
end
end # - I2C 3
device pci 17.0 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "IRQ_EDGE_LOW(GPIO_18_IRQ)"
register "wake" = "GPE0_DW1_15"
device i2c 15 on end
end
end # - I2C 4
device pci 17.1 on end # - I2C 5
device pci 17.2 on end # - I2C 6
device pci 17.3 on end # - I2C 7
device pci 18.0 on end # - UART 0
device pci 18.1 on end # - UART 1
device pci 18.2 on end # - UART 2
device pci 18.3 on end # - UART 3
device pci 19.0 on end # - SPI 0
device pci 19.1 on end # - SPI 1
device pci 19.2 on end # - SPI 2
device pci 1a.0 on end # - PWM
device pci 1b.0 on end # - SDCARD
device pci 1c.0 on end # - eMMC
device pci 1e.0 off end # - SDIO
device pci 1f.0 on # - LPC
chip ec/google/chromeec
device pnp 0c09.0 on end
end
end
device pci 1f.1 on end # - SMBUS
end
end
|
