1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
|
chip soc/intel/apollolake
# EMMC Tx CMD Delay
# Refer to EDS-Vol2-16.32.
# [14:8] steps of delay for DDR mode, each 125ps.
# [6:0] steps of delay for SDR mode, each 125ps.
register "emmc_tx_cmd_cntl" = "0x505"
# EMMC TX DATA Delay 1
# Refer to EDS-Vol2-16.33.
# [14:8] steps of delay for HS400, each 125ps.
# [6:0] steps of delay for SDR104/HS200, each 125ps.
register "emmc_tx_data_cntl1" = "0x0b0c"
# EMMC TX DATA Delay 2
# Refer to EDS-Vol2-16.34.
# [30:24] steps of delay for SDR50, each 125ps.
# [22:16] steps of delay for DDR50, each 125ps.
# [14:8] steps of delay for SDR25/HS50, each 125ps.
# [6:0] steps of delay for SDR12, each 125ps.
register "emmc_tx_data_cntl2" = "0x1c282929"
# EMMC RX CMD/DATA Delay 1
# Refer to EDS-Vol2-16.35.
# [30:24] steps of delay for SDR50, each 125ps.
# [22:16] steps of delay for DDR50, each 125ps.
# [14:8] steps of delay for SDR25/HS50, each 125ps.
# [6:0] steps of delay for SDR12, each 125ps.
register "emmc_rx_cmd_data_cntl1" = "0x00181b1b"
# EMMC RX CMD/DATA Delay 2
# Refer to EDS-Vol2-16.37.
# [17:16] stands for Rx Clock before Output Buffer
# [14:8] steps of delay for Auto Tuning Mode, each 125ps.
# [6:0] steps of delay for HS200, each 125ps.
register "emmc_rx_cmd_data_cntl2" = "0x10028"
# EMMC Rx Strobe Delay
# Refer to EDS-Vol2-16.36.
# [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps.
# [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps.
register "emmc_rx_strobe_cntl" = "0x0b0b"
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| GSPI0 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| | before memory is up |
#| I2C5 | Audio |
#| I2C6 | Trackpad |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.gspi[0] = {
.speed_mhz = 1,
.early_init = 1,
},
.i2c[5] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 104,
.fall_time_ns = 52,
},
.i2c[6] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 66,
.fall_time_ns = 90,
.data_hold_time_ns = 350,
},
}"
device domain 0 on
device pci 17.1 on
chip drivers/i2c/da7219
register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_137_IRQ)"
register "btn_cfg" = "50"
register "mic_det_thr" = "500"
register "jack_ins_deb" = "20"
register "jack_det_rate" = ""32ms_64ms""
register "jack_rem_deb" = "1"
register "a_d_btn_thr" = "0xa"
register "d_b_btn_thr" = "0x16"
register "b_c_btn_thr" = "0x21"
register "c_mic_btn_thr" = "0x3e"
register "btn_avg" = "4"
register "adc_1bit_rpt" = "1"
register "micbias_lvl" = "2600"
register "mic_amp_in_sel" = ""diff""
device i2c 1a on end
end
end # - I2C 5
device pci 17.2 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPIO_135_IRQ)"
register "wake" = "GPE0_DW3_27"
register "probed" = "1"
device i2c 15 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""PNP0C50""
register "generic.desc" = ""Synaptics Touchpad""
register "generic.irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPIO_135_IRQ)"
register "generic.wake" = "GPE0_DW3_27"
register "generic.probed" = "1"
register "hid_desc_reg_offset" = "0x20"
device i2c 0x2c on end
end
end # - I2C 6
end
end
|
