1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <amdblocks/acpimmio.h>
#include <amdblocks/espi.h>
#include <amdblocks/lpc.h>
#include <bootblock_common.h>
#include <baseboard/variants.h>
#include <console/console.h>
#include <delay.h>
#include <device/pci_ops.h>
#include <soc/lpc.h>
#include <soc/pci_devs.h>
#include <soc/southbridge.h>
#include <timer.h>
#define FC350_PCIE_INIT_DELAY_US (20 * USECS_PER_MSEC)
struct stopwatch pcie_init_timeout_sw;
void mb_set_up_early_espi(void)
{
/*
* We don't need to initialize all of the GPIOs that are done
* in bootblock_mainboard_early_init(), but we need to release
* the EC eSPI reset and do the rest of the configuration.
*
* This will not be present in the normal boot flow.
*/
bootblock_mainboard_early_init();
}
void bootblock_mainboard_early_init(void)
{
uint32_t dword;
size_t base_num_gpios, override_num_gpios;
const struct soc_amd_gpio *base_gpios, *override_gpios;
dword = pci_read_config32(SOC_LPC_DEV, LPC_MISC_CONTROL_BITS);
dword &= ~(LPC_LDRQ0_PU_EN | LPC_LDRQ1_EN | LPC_LDRQ0_EN);
dword |= LPC_LDRQ0_PD_EN;
pci_write_config32(SOC_LPC_DEV, LPC_MISC_CONTROL_BITS, dword);
pci_write_config32(SOC_LPC_DEV, LPC_IO_PORT_DECODE_ENABLE, 0);
pci_write_config32(SOC_LPC_DEV, LPC_IO_OR_MEM_DECODE_ENABLE, 0);
if (CONFIG(VBOOT_STARTS_BEFORE_BOOTBLOCK))
return;
base_gpios = variant_early_gpio_table(&base_num_gpios);
override_gpios = variant_early_override_gpio_table(&override_num_gpios);
gpio_configure_pads_with_override(base_gpios, base_num_gpios,
override_gpios, override_num_gpios);
/* Set a timer to make sure there's enough delay for
* the Fibocom 350 PCIe init
*/
stopwatch_init_usecs_expire(&pcie_init_timeout_sw, FC350_PCIE_INIT_DELAY_US);
/* Early eSPI interface configuration */
dword = pm_read32(PM_SPI_PAD_PU_PD);
dword |= PM_ESPI_CS_USE_DATA2;
pm_write32(PM_SPI_PAD_PU_PD, dword);
/* Switch the pads that can be used as either LPC or secondary eSPI to 1.8V mode */
dword = pm_read32(PM_ACPI_CONF);
dword |= PM_ACPI_S5_LPC_PIN_MODE | PM_ACPI_S5_LPC_PIN_MODE_SEL;
pm_write32(PM_ACPI_CONF, dword);
}
void bootblock_mainboard_init(void)
{
size_t base_num_gpios, override_num_gpios;
const struct soc_amd_gpio *base_gpios, *override_gpios;
int i = 0;
/* Make sure that at least 20ms has elapsed since enabling WWAN power
* in bootblock_mainboard_early_init.
* This is only applicable if verstage is not in the PSP and the board
* is using the fibocom 350 WLAN card, so this typically will not be hit.
*/
if (!CONFIG(VBOOT_STARTS_BEFORE_BOOTBLOCK) && variant_has_pcie_wwan()) {
while (!stopwatch_expired(&pcie_init_timeout_sw)) {
mdelay(1);
i++;
};
if (i)
printk(BIOS_DEBUG, "Delayed %d ms for PCIe\n", i);
}
base_gpios = variant_bootblock_gpio_table(&base_num_gpios);
override_gpios = variant_bootblock_override_gpio_table(&override_num_gpios);
gpio_configure_pads_with_override(base_gpios, base_num_gpios, override_gpios,
override_num_gpios);
/* FPMCU check needs to happen after EC initialization for FW_CONFIG bits */
if (variant_has_fpmcu())
variant_fpmcu_reset();
}
|
