1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
|
chip soc/intel/skylake
# IGD Displays
register "gfx" = "GMA_STATIC_DISPLAYS(0)"
register "panel_cfg" = "{
.up_delay_ms = 200,
.down_delay_ms = 50,
.cycle_delay_ms = 500,
.backlight_on_delay_ms = 1,
.backlight_off_delay_ms = 200,
.backlight_pwm_hz = 1000,
}"
# Enable deep Sx states
register "deep_s3_enable_ac" = "0"
register "deep_s3_enable_dc" = "0"
register "deep_s5_enable_ac" = "1"
register "deep_s5_enable_dc" = "1"
register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN"
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route. i.e. If this route changes then the affected GPE
# offset bits also need to be changed.
register "gpe0_dw0" = "GPP_B"
register "gpe0_dw1" = "GPP_D"
register "gpe0_dw2" = "GPP_E"
# EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
register "gen1_dec" = "0x00fc0801"
register "gen2_dec" = "0x000c0201"
# Enable DPTF
register "dptf_enable" = "1"
# FSP Configuration
register "SataSalpSupport" = "0"
register "SataPortsEnable[0]" = "0"
register "DspEnable" = "1"
register "IoBufferOwnership" = "3"
register "SsicPortEnable" = "0"
register "ScsEmmcHs400Enabled" = "1"
register "SkipExtGfxScan" = "1"
register "SaGv" = "SaGv_Enabled"
register "PmConfigSlpS3MinAssert" = "2" # 50ms
register "PmConfigSlpS4MinAssert" = "4" # 4s
register "PmConfigSlpSusMinAssert" = "3" # 4s
register "PmConfigSlpAMinAssert" = "3" # 2s
# Enable Root port 1
register "PcieRpEnable[0]" = "1"
# Enable CLKREQ#
register "PcieRpClkReqSupport[0]" = "1"
# RP 1 uses SRCCLKREQ1#
register "PcieRpClkReqNumber[0]" = "1"
# Must leave UART0 enabled or SD/eMMC will not work as PCI
register "SerialIoDevMode" = "{
[PchSerialIoIndexI2C0] = PchSerialIoPci,
[PchSerialIoIndexI2C1] = PchSerialIoPci,
[PchSerialIoIndexI2C2] = PchSerialIoDisabled,
[PchSerialIoIndexI2C3] = PchSerialIoDisabled,
[PchSerialIoIndexI2C4] = PchSerialIoPci,
[PchSerialIoIndexI2C5] = PchSerialIoDisabled,
[PchSerialIoIndexSpi0] = PchSerialIoDisabled,
[PchSerialIoIndexSpi1] = PchSerialIoDisabled,
[PchSerialIoIndexUart0] = PchSerialIoPci,
[PchSerialIoIndexUart1] = PchSerialIoDisabled,
[PchSerialIoIndexUart2] = PchSerialIoSkipInit,
}"
# I2C4 is 1.8V
register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8"
# PL2 override 25W
register "power_limits_config" = "{
.tdp_pl2_override = 25,
}"
# Send an extra VR mailbox command for the PS4 exit issue
register "SendVrMbxCmd" = "2"
device domain 0 on
device ref igpu on end
device ref sa_thermal on end
device ref south_xhci on end
device ref thermal on end
device ref i2c0 on end
device ref i2c1 on end
device ref heci1 on end
device ref uart2 on end
device ref i2c4 on end
device ref pcie_rp1 on
chip drivers/wifi/generic
register "wake" = "GPE0_DW0_16"
device pci 00.0 on end
end
end
device ref uart0 on end
device ref emmc on end
device ref lpc_espi on
chip drivers/pc80/tpm
device pnp 0c31.0 on end
end
chip ec/google/chromeec
device pnp 0c09.0 on end
end
end
device ref hda on end
device ref smbus on end
device ref fast_spi on end
end
end
|
