1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <arch/mmu.h>
#include <device/device.h>
#include <soc/addressmap.h>
#include <soc/clk_rst.h>
#include <soc/clock.h>
#include <soc/funitcfg.h>
#include <soc/nvidia/tegra/i2c.h>
#include <soc/padconfig.h>
#include <soc/spi.h>
#include <soc/nvidia/tegra/dc.h>
#include <soc/display.h>
#include <vendorcode/google/chromeos/chromeos.h>
static const struct pad_config sdmmc1_pad[] = {
/* MMC1(SDCARD) */
PAD_CFG_SFIO(SDMMC1_CLK, PINMUX_INPUT_ENABLE, SDMMC1),
PAD_CFG_SFIO(SDMMC1_CMD, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SDMMC1),
PAD_CFG_SFIO(SDMMC1_DAT0, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SDMMC1),
PAD_CFG_SFIO(SDMMC1_DAT1, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SDMMC1),
PAD_CFG_SFIO(SDMMC1_DAT2, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SDMMC1),
PAD_CFG_SFIO(SDMMC1_DAT3, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SDMMC1),
/* MMC1 Card Detect pin */
PAD_CFG_GPIO_INPUT(GPIO_PZ1, PINMUX_PULL_UP),
/* Disable SD card reader power so it can be reset even on warm boot.
Payloads must enable power before accessing SD card slots. */
PAD_CFG_GPIO_OUT0(GPIO_PZ4, PINMUX_PULL_NONE),
};
static const struct pad_config audio_codec_pads[] = {
/* GPIO_X1_AUD(BB3) is AUDIO_LDO_EN (->CODEC RESET_N pin) */
PAD_CFG_GPIO_OUT1(GPIO_X1_AUD, PINMUX_PULL_DOWN),
};
static const struct pad_config padcfgs[] = {
/* We pull the USB VBUS signals up but keep them as inputs since the
* voltage source likes to drive them low on overcurrent conditions */
PAD_CFG_GPIO_INPUT(USB_VBUS_EN1, PINMUX_PULL_NONE | PINMUX_PARKED |
PINMUX_INPUT_ENABLE | PINMUX_LPDR | PINMUX_IO_HV),
/* Add backlight vdd/enable/pwm/dp hpd pad cfgs here */
};
static const struct pad_config i2c1_pad[] = {
/* GEN1 I2C */
PAD_CFG_SFIO(GEN1_I2C_SCL, PINMUX_INPUT_ENABLE, I2C1),
PAD_CFG_SFIO(GEN1_I2C_SDA, PINMUX_INPUT_ENABLE, I2C1),
};
static const struct pad_config i2s1_pad[] = {
/* I2S1 */
PAD_CFG_SFIO(DAP1_SCLK, PINMUX_INPUT_ENABLE, I2S1),
PAD_CFG_SFIO(DAP1_FS, PINMUX_INPUT_ENABLE, I2S1),
PAD_CFG_SFIO(DAP1_DOUT, PINMUX_INPUT_ENABLE, I2S1),
PAD_CFG_SFIO(DAP1_DIN, PINMUX_INPUT_ENABLE | PINMUX_TRISTATE, I2S1),
/* codec MCLK via AUD SFIO */
PAD_CFG_SFIO(AUD_MCLK, PINMUX_PULL_NONE, AUD),
};
static const struct funit_cfg audio_funit[] = {
/* We need 1.5MHz for I2S1. So we use CLK_M */
FUNIT_CFG(I2S1, CLK_M, 1500, i2s1_pad, ARRAY_SIZE(i2s1_pad)),
};
static const struct funit_cfg funitcfgs[] = {
FUNIT_CFG(SDMMC1, PLLP, 48000, sdmmc1_pad, ARRAY_SIZE(sdmmc1_pad)),
FUNIT_CFG(SDMMC4, PLLP, 48000, NULL, 0),
FUNIT_CFG(I2C1, PLLP, 100, i2c1_pad, ARRAY_SIZE(i2c1_pad)),
FUNIT_CFG(I2C6, PLLP, 400, audio_codec_pads, ARRAY_SIZE(audio_codec_pads)),
FUNIT_CFG_USB(USBD),
};
/* Audio init: clocks and enables/resets */
static void setup_audio(void)
{
/* Audio codec (ES755) uses OSC freq (via AUD_MCLK), s/b 38.4MHz */
soc_configure_funits(audio_funit, ARRAY_SIZE(audio_funit));
/*
* As per NVIDIA hardware team, we need to take ALL audio devices
* connected to AHUB (AUDIO, APB2APE, I2S, SPDIF, etc.) out of reset
* and clock-enabled, otherwise reading AHUB devices (in our case,
* I2S/APBIF/AUDIO<XBAR>) will hang.
*/
soc_configure_ape();
clock_enable_audio();
}
static void mainboard_init(struct device *dev)
{
soc_configure_pads(padcfgs, ARRAY_SIZE(padcfgs));
soc_configure_funits(funitcfgs, ARRAY_SIZE(funitcfgs));
i2c_init(I2C1_BUS);
setup_audio();
}
static void mainboard_enable(struct device *dev)
{
dev->ops->init = &mainboard_init;
}
struct chip_operations mainboard_ops = {
.enable_dev = mainboard_enable,
};
|
