blob: 28dc21caa4e6b9892764b6eceb38a761d101d03b (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
|
/* SPDX-License-Identifier: GPL-2.0-only */
#ifndef UART8250REG_H
#define UART8250REG_H
/* Data */
#define UART8250_RBR 0x00
#define UART8250_TBR 0x00
/* Control */
#define UART8250_IER 0x01
#define UART8250_IER_MSI 0x08 /* Enable Modem status interrupt */
#define UART8250_IER_RLSI 0x04 /* Enable receiver line status interrupt */
#define UART8250_IER_THRI 0x02 /* Enable Transmitter holding register int. */
#define UART8250_IER_RDI 0x01 /* Enable receiver data interrupt */
#define UART8250_IIR 0x02
#define UART8250_IIR_NO_INT 0x01 /* No interrupts pending */
#define UART8250_IIR_ID 0x06 /* Mask for the interrupt ID */
#define UART8250_IIR_MSI 0x00 /* Modem status interrupt */
#define UART8250_IIR_THRI 0x02 /* Transmitter holding register empty */
#define UART8250_IIR_RDI 0x04 /* Receiver data interrupt */
#define UART8250_IIR_RLSI 0x06 /* Receiver line status interrupt */
#define UART8250_FCR 0x02
#define UART8250_FCR_FIFO_EN 0x01 /* Fifo enable */
#define UART8250_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
#define UART8250_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
#define UART8250_FCR_DMA_SELECT 0x08 /* For DMA applications */
#define UART8250_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
#define UART8250_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
#define UART8250_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
#define UART8250_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
#define UART8250_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
#define UART8250_FCR_RXSR 0x02 /* Receiver soft reset */
#define UART8250_FCR_TXSR 0x04 /* Transmitter soft reset */
#define UART8250_LCR 0x03
#define UART8250_LCR_WLS_MSK 0x03 /* character length select mask */
#define UART8250_LCR_WLS_5 0x00 /* 5 bit character length */
#define UART8250_LCR_WLS_6 0x01 /* 6 bit character length */
#define UART8250_LCR_WLS_7 0x02 /* 7 bit character length */
#define UART8250_LCR_WLS_8 0x03 /* 8 bit character length */
#define UART8250_LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */
#define UART8250_LCR_PEN 0x08 /* Parity enable */
#define UART8250_LCR_EPS 0x10 /* Even Parity Select */
#define UART8250_LCR_STKP 0x20 /* Stick Parity */
#define UART8250_LCR_SBRK 0x40 /* Set Break */
#define UART8250_LCR_BKSE 0x80 /* Bank select enable */
#define UART8250_LCR_DLAB 0x80 /* Divisor latch access bit */
#define UART8250_MCR 0x04
#define UART8250_MCR_DTR 0x01 /* DTR */
#define UART8250_MCR_RTS 0x02 /* RTS */
#define UART8250_MCR_OUT1 0x04 /* Out 1 */
#define UART8250_MCR_OUT2 0x08 /* Out 2 */
#define UART8250_MCR_LOOP 0x10 /* Enable loopback test mode */
#define UART8250_MCR_DMA_EN 0x04
#define UART8250_MCR_TX_DFR 0x08
#define UART8250_DLL 0x00
#define UART8250_DLM 0x01
/* Status */
#define UART8250_LSR 0x05
#define UART8250_LSR_DR 0x01 /* Data ready */
#define UART8250_LSR_OE 0x02 /* Overrun */
#define UART8250_LSR_PE 0x04 /* Parity error */
#define UART8250_LSR_FE 0x08 /* Framing error */
#define UART8250_LSR_BI 0x10 /* Break */
#define UART8250_LSR_THRE 0x20 /* Xmit holding register empty */
#define UART8250_LSR_TEMT 0x40 /* Xmitter empty */
#define UART8250_LSR_ERR 0x80 /* Error */
#define UART8250_MSR 0x06
#define UART8250_MSR_DCD 0x80 /* Data Carrier Detect */
#define UART8250_MSR_RI 0x40 /* Ring Indicator */
#define UART8250_MSR_DSR 0x20 /* Data Set Ready */
#define UART8250_MSR_CTS 0x10 /* Clear to Send */
#define UART8250_MSR_DDCD 0x08 /* Delta DCD */
#define UART8250_MSR_TERI 0x04 /* Trailing edge ring indicator */
#define UART8250_MSR_DDSR 0x02 /* Delta DSR */
#define UART8250_MSR_DCTS 0x01 /* Delta CTS */
#define UART8250_SCR 0x07
#define UART8250_SPR 0x07
#endif /* UART8250REG_H */
|
