1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <acpi/acpi_device.h>
#define CS35L53_MAX_GPIOS 2
enum cs35l53_boost_type {
INTERNAL_BOOST = 0,
EXTERNAL_BOOST = 1,
};
enum cs35l53_boost_ind_nanohenrys {
BOOST_IND_1000_NH = 1000,
BOOST_IND_1200_NH = 1200,
BOOST_IND_1500_NH = 1500,
BOOST_IND_2200_NH = 2200,
};
enum cs35l53_asp_sdout_hiz {
ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED = 0,
ASP_SDOUT_HIZ_UNUSED_LOGIC0_DISABLED = 1,
ASP_SDOUT_LOGIC0_UNUSED_HIZ_DISABLED = 2,
ASP_SDOUT_HIZ_UNUSED_HIZ_DISABLED = 3,
};
enum cs35l53_gpio1_src {
GPIO1_SRC_HIGH_IMPEDANCE = 0,
GPIO1_SRC_GPIO = 1,
GPIO1_SRC_SYNC = 2,
GPIO1_SRC_MCLK_INPUT = 3,
};
enum cs35l53_gpio2_src {
GPIO2_SRC_HIGH_IMPEDANCE = 0,
GPIO2_SRC_GPIO = 1,
GPIO2_SRC_OPEN_DRAIN = 2,
GPIO2_SRC_MCLK_INPUT = 3,
GPIO2_SRC_PUSH_PULL_INTB = 4,
GPIO2_SRC_PUSH_PULL_INT = 5,
};
/*
* Cirrus Logic CS35L53 Audio Codec devicetree bindings
* linux/Documentation/devicetree/bindings/sound/cirrus,cs35l53.yaml
*/
struct drivers_i2c_cs35l53_config {
const char *name; /* ACPI Device Name */
const char *sub; /* SUB ID to uniquely identify system */
/* Interrupt configuration */
struct acpi_irq irq;
/* Use GPIO based interrupt instead of PIRQ */
struct acpi_gpio irq_gpio;
/* Use GPIO based reset gpio */
struct acpi_gpio reset_gpio;
/* I2C Bus Frequency in Hertz (default 400kHz) */
unsigned int bus_speed;
/* Define cs35l53 parameters */
/*
* cirrus,boost-type : Configures the type of Boost being used.
* Internal boost requires boost-peak-milliamp, boost-ind-nanohenry and
* boost-cap-microfarad.
* External Boost must have GPIO1 as GPIO output. GPIO1 will be set high to
* enable boost voltage.
*/
enum cs35l53_boost_type boost_type;
/*
* cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
* Configures the peak current by monitoring the current through the boost FET.
* Range starts at 1600 mA and goes to a maximum of 4500 mA with increments
* of 50 mA. See section 4.3.6 of the datasheet for details.
*/
unsigned int boost_peak_milliamp;
/*
* cirrus,boost-ind-nanohenry : Boost inductor value, expressed in nH. Valid
* values include 1000, 1200, 1500 and 2200.
*/
enum cs35l53_boost_ind_nanohenrys boost_ind_nanohenry;
/*
* cirrus,boost-cap-microfarad : Total equivalent boost capacitance on the VBST
* and VAMP pins, derated at 11 volts DC. The value must be rounded to the
* nearest integer and expressed in uF.
*/
unsigned int boost_cap_microfarad;
/*
* cirrus,asp-sdout-hiz : Audio serial port SDOUT Hi-Z control. Sets the Hi-Z
* configuration for SDOUT pin of amplifier.
* 0 = Logic 0 during unused slots, and while all transmit channels disabled
* 1 = Hi-Z during unused slots but logic 0 while all transmit channels disabled
* 2 = Logic 0 during unused slots, but Hi-Z while all transmit channels disabled
* 3 = Hi-Z during unused slots and while all transmit channels disabled
*/
enum cs35l53_asp_sdout_hiz asp_sdout_hiz;
/*
* cirrus,gpio1-polarity-invert : Boolean which specifies whether the GPIO1
* level is inverted.
*/
bool gpio1_polarity_invert;
/*
* cirrus,gpio2-polarity-invert : Boolean which specifies whether the GPIO2
* level is inverted.
*/
bool gpio2_polarity_invert;
/*
* cirrus,gpio1-output-enable : Boolean which specifies whether the GPIO1 pin
* is configured as an output.
*/
bool gpio1_output_enable;
/*
* cirrus,gpio2-output-enable : Boolean which specifies whether the GPIO2 pin
* is configured as an output.
*/
bool gpio2_output_enable;
/*
* cirrus,gpio1-src-select : Configures the function of the GPIO1 pin.
* GPIO1:
* 0 = High Impedance (Default)
* 1 = GPIO
* 2 = Sync
* 3 = MCLK input
*/
enum cs35l53_gpio1_src gpio1_src_select;
/*
* cirrus,gpio2-src-select : Configures the function of the GPIO2 pin.
* GPIO2:
* 0 = High Impedance (Default)
* 1 = GPIO
* 2 = Open Drain INTB
* 3 = MCLK input
* 4 = Push-pull INTB (active low)
* 5 = Push-pull INT (active high)
*/
enum cs35l53_gpio2_src gpio2_src_select;
};
|
