| Age | Commit message (Collapse) | Author |
|---|
|
Update autoport for:
1. Commit ee126348726b ("nb/sandybridge,sb/bd82x6x: Configure USB from
southbridge devicetree")
2. Commit 94625d2aae76 ("sb/intel/bd82x6x: Allow actual USBIRx values
for native USB config")
As a side effect of #2 above, no more (broken anyway) FIXME comment
will be written for usb_port_config.
Change-Id: I3b8f44d9de19a7446e2fbcbce1aab6ec6583ebe3
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Commit 45e4ab4a660c (mb/*: Update SPD mapping for sandybridge boards)
changed the way in which SPD addresses are set up for SNB/IVB boards,
but autoport was not updated to reflect these changes. Result is:
register "spd_addresses" = "{0x50, 0x51, 0x52, 0x53}" # FIXME: Put proper SPD map here"
The stray quote at the end is irritating, but is hard to get rid of
without substantial refactoring of autoport's guts. But, given that
this is a FIXME comment, anyone using autoport should just drop the
comment after verifying the SPD map, so it's not a big deal.
In addition, update the corresponding section of the README, which
was horrendously out-of-date.
Change-Id: I6ad38f53afc4fafb45be7f086723cc0782a965ed
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82405
Reviewed-by: Keith Hui <buurin@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on the non-public "ITE IT8659E-I Preliminary Specification V0.7.2
(For H Version)".
TEST=Dump IT8659E configuration on the new Protectli platform
Change-Id: Ic036f8b99d5bd0107be7850fc4509da1bf020fe5
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Replace 3 unused values in the map with those found during a Ghidra
examination of MRC binary, and on hardwares running vendor firmware
(asus/p8z77-m and HP Z210 CMT Workstation).
The outgoing values were introduced in commit 216ad2170ca8
("sb/intel/bd82x6x: Add new USB currents") in anticipation for
Gigabyte GA-Z77-DS3H mainboard, but effort to land it was eventually
abandoned. Since commit xxxxxxxxxxxx, such values can be placed
directly in the port config, so there should be no hurdle should that
effort be resurrected.
Add a few #defines in pch.h to place some inline documentation
on MRC values, but more will be documented in the future when this
mapping is introduced MRC-side.
Finally, update autoport to match.
Change-Id: I195c7f627994e48f7a6e6698589504dc96248cff
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
We are going to expose ths tool to end users, and want to take
care that the presented information can be consumed by them.
The current code simply prints below warnings if we use release
binary available for end-user to download:
No firmware volume header present
No valid firmware volume was found
It will be concerning and not clear to end users, they might not
understant why it happens, what are the implications, and whether
it is something that they should worry about.
This commit tries to explain what actually happens here.
Change-Id: Iaa2678f5ae7c243811484c0567ced97ae0b3fc0a
Signed-off-by: Maciej Pijanowski <maciej.pijanowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
|
|
Wflex-array-member-not-at-end & Wcalloc-transposed-args are
not supported when using GCC older than GCC-14.
Use them only when supported.
Change-Id: I11c1e729569c8130bd254a10454c5066a72974d6
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82785
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
linux_trampoline.c generation is broken with latest crossgcc-i386
toolchain. Fix the issue to enable the building.
../cbfstool/linux_trampoline.S: Assembler messages:
../cbfstool/linux_trampoline.S:100: Error: no instruction mnemonic
suffix given and no register operands; can't size
instruction
<builtin>: recipe for target '../cbfstool/linux_trampoline.o'
failed
TEST=Build and boot on intel/archercity CRB
cd util/cbfstool/
rm linux_trampoline.c
make linux_trampoline.c
Change-Id: I7faca296f946bb4e9fd510661357925e5dcf9a6b
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82704
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
<stdio.h> header is used for input/output operations (such as printf,
scanf, fopen, etc.). Although some input/output functions can manipulate
strings, they do not need to directly include <string.h> because they
are declared independently.
Change-Id: Ibe2a4ff6f68843a6d99cfdfe182cf2dd922802aa
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82665
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I75909ce85eed549d9094ba6f62d93656621d9f0d
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82679
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic03d9ac883a92d52467d563f048446871b928712
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This excludes Devicetree blob files from the list of files to check for
superfluous whitespaces. A DTB file has recently been added in commit
33079b8174 ("lib/device_tree: Add some FDT helper functions").
Change-Id: Ic25ee5361163446370c530cccefa3bf085895d15
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82638
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds some helper functions for FDT, since more and more mainboards
seem to need FDT nowadays. For example our QEMU boards need it in order
to know how much RAM is available. Also all RISC-V boards in our tree
need FDT.
This also adds some tests in order to test said functions.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I2fb1d93c5b3e1cb2f7d9584db52bbce3767b63d8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81081
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie087f43e6f60df7b97d7d7b402d3540c3a0a2461
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Debian sid is too unstable at this point, and frequently ends up having
issues that cause the coreboot-sdk docker image to fail to build. Using
stable also better reflects what users will typically be running.
Also remove the parameters to quiet the apt-get install command so that
if something does break, we can see what happened more easily.
Fixes bug 536
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I41b6464b024df89c114db2cdb9367c0526eb0297
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82411
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Idf5912d1fcdfabab7fe006b7e0cd4ebd25c07d09
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81683
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Change-Id: I03a44e0c23a925396f614f282882405dc886ba58
Signed-off-by: Lennart Eichhorn <lennarteichhorn@googlemail.com>
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Remove the patch since it was picked from master before and thus it's
included in the new release.
Change-Id: I70408b189b974f8abaadc66f0c809a1dbe10504b
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81900
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I41f56ba58af51b1ec1d7554fb35a49ccf9e778f6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Change-Id: Iaf2d4f579d987fbfd4187ae41c1be5cec55e0e8e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Yes, the DSDT revision is the OEM revision. But most certainly not that
of the board being ported. Because no one seems to care about the value
(newer boards inexplicably use lower values even though this represents
a date in 0xYYYYMMDD format), simply drop the incorrect comment. Should
save a bit of effort when reviewing mainboard ports: no longer will one
have to ask authors to drop the comment.
Change-Id: I9c425573e4fcb0f670a780e7821e815eadc8a2aa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The README suggests using `logs` as the folder name where autoport puts
the generated logs. Thus, add this folder to .gitignore for the sake of
convenience. Yes, people can use other folder names, but `logs` is most
commonly used.
Change-Id: I37906b43ba3e132de616184e4a5082ce00f4b230
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82398
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Pad names now matching soc/intel/xeon_sp/ebg/soc_gpio.c.
Test: Generated pad names for ASRock Rack SPC741D8 now compile.
Change-Id: Ied53b654f905add86a05bce8c2e366dea9ccf4d3
Signed-off-by: Fabian Meyer <fabian.meyer@student.kit.edu>
Co-authored-by: Yussuf Khalil <yussuf.khalil@kit.edu>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82205
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enables parsing Meteor Lake inteltool output into gpio.h pad macros.
Change-Id: Iaebd51d587507e68c6f263b92dc61cb6c0411bf8
Signed-off-by: Filip Lewiński <filip.lewinski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81916
Reviewed-by: Maxim <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Kopeć <michal.kopec@3mdeb.com>
|
|
Based on:
Intel Core Ultra Processor External Design Specification
Meteor Lake SOC IO Registers
Meteor Lake-U/H/U Type4 and Arrow Lake-U/H GPIO Implementation Summary
Change-Id: I7473119fa97c57cd2a1303f08f964abd0ca96270
Signed-off-by: Filip Lewiński <filip.lewinski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Kopeć <michal.kopec@3mdeb.com>
|
|
If $BOARD is not all lowercase, then certain subfunctions of the
script will fail due to case-sensitive comparisons therein. To avoid
this, since all matched strings are fully lowercase, set $BOARD
to lowercase.
TEST: './crosfirmware.sh {akemi/Akemi/AKEMI}' all succeed.
Change-Id: I8ecb613a8d9384e2cccaff5183470e2e9956d0a2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This file is appended to Documentation/util.md by the util_readme.sh
script, and contains toctree entries for utilities with more in-depth
documentation than the description automatically pulled from the
description.md files throughout the util directory. As of commit
35599f9a6671 (Docs: Replace Recommonmark with MyST Parser), the syntax
for creating a toctree has changed, so update this post_util.md
accordingly.
Change-Id: Ia7ae3c513781e53512763578fd97db7e2f75e65c
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Replace transitional 'pkg-config' package with 'pkgconf'.
Change-Id: I9ee895cb2ca3186c4aefbdab1fd71778bf981009
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82167
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When installing the packages, apt-get returns an error about holding
broken packages. It occurs the diffutils depends on libcurl4t64
which breaks the libcurl4.
As a solution, remove the libcurl4 from the list, and let the package
manager resolve the dependencies.
TEST=Build coreboot-sdk
Change-Id: Iabc4f74619d4462317d8adb4068e50135d89d80e
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
This patch adds support for the new command-line option `-c` to
the ifdtool, which is able to check GPR0 (Global Protected Range)
status.
This patch also add helper function get_enabled_gprd() to get enabled
GPR0 settings. It used in enable_gpr0() and is_gpr0_protected().
Developers can use ifdtool with '-c' option to check whether GPR0 is
set to enabled or disabled in the binary file.
BUG=none
TEST=(1) > ifdtool -p mtl -E image-unlocked.bin -O image-lock.bin
...
Value at GPRD offset (64) is 0x83220004
--------- GPR0 Protected Range --------------
Start address = 0x00004000
End address = 0x00322fff
...
GPR0 protection is now enabled
(2) > ifdtool -p mtl -c image-unlocked.bin
GPR0 status: Disabled
Value at GPRD offset (64) is 0x00000000
--------- GPR0 Protected Range --------------
Start address = 0x00000000
End address = 0x00000fff
(3) > ifdtool -p mtl -c image-lock.bin
GPR0 status: Enabled
Value at GPRD offset (64) is 0x83220004
--------- GPR0 Protected Range --------------
Start address = 0x00004000
End address = 0x00322fff
Change-Id: I6b3af973be784200b965a68e5f6b7737cba03ed7
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
This should keep new makefiles from being named Makefile.inc.
Change-Id: I4a47998e1c997b82b8a15319eae96cdc0de64e77
Signed-off-by: Martin Roth <gaumless@gmail.com>
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81857
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
The binary hashes from GitHub releases are not stable. Use the Intel
mirror.
Change-Id: If3738b0cdab07c37ac1459a53e399e5de54435d5
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80721
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The command "wget" prints some hyperlink with "%", which will be
filtered in by previous regular expression. So we need to change to
match the string with exactly 3 digits and a percent symbol.
TEST:
echo 45% | grep -o "\<[0-9]\{1,3\}%"
45%
echo 1245% | grep -o "\<[0-9]\{1,3\}%"
<empty>
echo aa% | grep -o "\<[0-9]\{1,3\}%"
<empty>
Change-Id: I6ef9e7c87fd4ee6cc707346954d91e6e3af3b939
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
<device/device.h> is supposed to provide <device/{path,resource}.h>
Change-Id: I2ef82c8fe30b1c1399a9f85c1734ce8ba16a1f88
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add support for TigerLake Halo SoC, based on CNL profile.
Test: Convert GPIO dump from inteltool into coreboot macros for
out-of-tree TGL board.
Change-Id: I26eff225c2045edfe5836283be7b4c63f6b405e8
Signed-off-by: Alicja Michalska <ahplka19@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim <max.senia.poliak@gmail.com>
|
|
Linux kconfig has its own implementation of KCONFIG_WERROR now, so use
that. This reduces our patch count by 2.
Change-Id: I4f5f1f552e96f8ef7a4c5c0ab2ab7e2b6d798ceb
Signed-off-by: Patrick Georgi <patrick@georgi.software>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81223
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With this, `quilt pop -a` leads to an original Linux kconfig tree,
making it easier to apply kconfig updates.
Change-Id: I771bbd0f8244cae38317bd5b1f809b74771b176f
Signed-off-by: Patrick Georgi <patrick@georgi.software>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
When doing LTO the clang linker frontend needs to use LLD or gold. Build
LLD as that is the configuration that is best tested.
Change-Id: I3242585f8b5c3426fc6568d3dc47300164d56e3a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
When the compiler is used as a linker frontend clang tries to match the
target string with what it supports internally. If it's not sufficiently
complete it will forward linking to GCC which is not desirable. This is
necessary when doing LTO with clang.
Change-Id: Ie9356a2bc0f5b77e934cc16482d6ccb1961195dc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80730
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is useful for listing older images.
Change-Id: I588028d4327f59538f7c9920b671458fc631cb4c
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
In order to preprocess linker scripts the target architecture needs to
be specified. With clang this needs to be set via a cli argument.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I4340681e30059d6f18a49a49937668cd3dd39ce1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
TEST=Identical binary test on all AMD SOC platform
Change-Id: Iece4ba65e0476543a8d472168d93801714330dde
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78281
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A trailing "|" at the end of the regex added a zero length alternative
match, causing all files to match and be filtered out. This was causing
`make lint-stable` to ignore all missing license headers, preventing the
pre-commit git hook and Jenkins from detecting these. Also, a missing
"|" separator between cmos.default and .apcb would cause those files to
be unintentionally scanned.
Change-Id: I70cc3a5adf7edee059883cd3cbe02029776b02ef
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Other function calls don't have to worry about the fletcher error.
TEST=Binary identical test on all AMD SOC platform
Change-Id: I7c9d653100b476b52d6d1d80c41d0c3d765f7be3
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Move the complexity from main to function, so the main flow is easy to
understand.
TEST=Identical test on all AMD SOC platform
Change-Id: Ia549a0d08c2a60b8858440543ac8d8b5259017dd
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: If27218df40e58f249769b3d84c0cd4c299e2282b
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
The documentation is now built using MyST Parser, so Recommonmark can be
dropped.
Change-Id: I7f6810c9429573c0c51d3d72b36e9fc2ae2185f5
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80313
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update all pip packages related to coreboot's documentation to their
latest available version, and update the doc.coreboot.org base image
to Alpine 3.19.1. Add myst-parser in preparation to switch from
Recommonmark to MyST Parser.
TEST: The documentation builds and renders properly when built using
the updated container.
Change-Id: I8df4aadabc49c0201a836333745fe138184595ac
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80312
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, pip modules are installed system-wide, which may cause
conflicts with modules installed using the package manager. Newer
versions of the Alpine base image also mark its system wide Python
installation as an externally managed environment, which will cause
pip to return an error as per recent Python recommendations [1].
TEST:
- `make -C util/docker doc.coreboot.org` builds the container
successfully
- `make -C util/docker docker-build-docs` builds the documentation
successfully
[1] https://peps.python.org/pep-0668/
Change-Id: Idd9cc5e6fb28b42ef8e4fa5db01eb9ef192ba0ec
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Change-Id: I8284c35a0124ba4588d199024e28d3445c681896
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>wq
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78763
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When the table is created, the cookie is known.
When the packing going on, the cookie in header can be checked to see
where we are.
TEST=Identical test on all AMD SOC platform
Change-Id: I300e30292c68a14b44c637b26a13b308dc9c0388
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81254
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Before every integration there is a header creation. We can put them
together. And the parameters for PSP/BIOS tables are useless.
TEST=Identical test on all AMD SOC platform
Change-Id: Ia9d78bb8145855203048208fcd67f8b9cd9d3199
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The purpose of integration function is to pack the FWs into table. We
need to remove other process. Create a dedicate function to link all
the tables together. And this linking function is only called when
both the level 1 and level 2 directory are created. This simplifies
the main function and logic.
TEST=Identical test on all AMD SOC platform
Change-Id: Ieaf97208e943c79d7b76ea62eea9355138c220b9
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Instead of being local variables. This can be easier to find all
the tables anywhere.
TEST=Identical test on all AMD SOC platform
Change-Id: I98b7d01e32c75b4f13e23d496cd3de3da900678d
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Remove redundant parameter "debug" from open_process_config().
Change-Id: Ib91a505838d7be4980d6b4f1e95fb8601fbbfd16
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81201
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For recovery A/B mode, the BIOS tables level 2 are traced by PSP table
instead of ROMSIG. There should not be a dedicated BIOS table, nor a
combo BIOS table.
Change-Id: I8735bd91b32bc9a0e4fc70d293e8d836d5e9c36b
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81137
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Our major version is suddenly two digits long to represent the year.
This can't be parsed with the current sed scripts. To make sure that
no unparsed data ends up in our major/minor versions, we'll run sed
with `-n' and only print the extracted numbers if anything. Also, to
allow us to use the version numbers in C code, we strip leading zeros
(a leading 0 identifies octal numbers, so for instance 08 for August
is not a valid number).
This can result in empty major/minor version strings, so we move the
default `0' to the final variable expansion.
As a bonus, this makes an explicit check if the numbers can be parsed
unnecessary.
Change-Id: Ie39381a8ef4b971556168b6996efeefe6adf2b14
Reported-by: Christoph Zechner <christophz@vrvis.at>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81290
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Previously the incorrect 'd' format specifier was used despite the '0x'
prefix implying hex to the user.
Change-Id: Ib97bd86ee0e0c8fe8c3785e22a4d9f6def3cae61
Signed-off-by: Mate Kukri <kukri.mate@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
It was complicated and weird to check both the cookie and whether one
table is a null pointer. Just checking the cookie is enough.
TEST=Identical test on all AMD SOC platform
Change-Id: Icab74714990f74e11fd5e899661e4e2d41230541
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81208
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The entry in the table has two categaries, file and pointer. For the
pointer, it does not take table space. The ISH, PSP level 2, BIOS
table are all the pointer type. So integration function only packs FWs
located in folder amd_blobs. And only FWs increase the table size.
So the table size is only set once. Later calls only update the count
and fletcher. The table has a header at least, so the size can not be
0.
The fill_dir_header can take the parameter count as 0, such PSP level
1 only with ISH-A and ISH-B. It doesn't have any file type entries.
This actually reverts
https://review.coreboot.org/c/coreboot/+/78274
and adds other changes.
TEST=Identical test on all AMD SOC platform
Change-Id: I5dfbbb55912c8e37243c351427a8df89c12e5da8
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81255
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Posix shell doesn't support '=='
Change-Id: Icbdc4204f4c07d806e721fa39f96694c4df00e8d
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81285
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a Nix shell file to provide a simple environment for coreboot
development of i386 architecture. Currently, this environment is
capable of completing Tutorial Part 1 in https://doc.coreboot.org.
The Nix shell can be used by running the following command:
$ nix-shell --pure util/nixshell/devshell-i386.nix
The `--pure` parameter is optional.
In Nixpkgs, there is a package called 'coreboot-toolchain'. It
fetches the source code of coreboot, build crossgcc, and export
it as output. With the binary cache mechanism of Nix, crossgcc
can be directly downloaded and used without compiling on user's
machine.
This Nix shell has been tested on a NixOS laptop and a Debian 12
server, and they both work fine.
Change-Id: Idcfe10be214e9bca590a62b8a207267493a4861f
Signed-off-by: Crabtux <crabtux@mail.ustc.edu.cn>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
PAYLOAD_INFO is a very old feature that can add a key/value information
section to a payload file. It seems to have only ever been generated by
coreinfo and never really read by anything.
Since CB:1721 in 2012, the feature has been inadvertently broken in
practice since the `.note.pinfo` sections that contain the information
get discarded from the payload before cbfstool gets to see them. Since
CB:28647 in 2018, support for the section in the SELF loader was
(inadvertently?) dropped, so if someone actually fed cbfstool a payload
ELF that did have a `.note.pinfo` section, modern coreboot would refuse
to boot the payload entirely (which is probably not a good state to
leave things in).
This patch removes the code to generate PAYLOAD_INFO entries entirely,
but leaves the support to parse and extract those sections from old
payloads in place in cbfstool.
Change-Id: I40d8e9b76a171ebcdaa2eae02d54a1ca5e592c85
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Reference: Intel Processor and Intel Core i3 N-Series Datasheet,
Volume 1 of 2 (#759603)
Change-Id: Ib3225088fa08fb7e5a60c87d0f1f6b3001f5b562
Signed-off-by: Brandon Weeks <me@brandonweeks.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
If the host directory of a bind mount does not exist, Docker will create
it. However, the newly created directory will be owned by root due to
the Docker service running within a root context. The docker command in
the recipe for docker-build-docs binds Documentation/_build to /data-out
within the container, so if it doesn't already exist, the documentation
builder will be unable to copy the HTML output into /data-out since it
runs with the same UID and GID as the host user.
By creating, if necessary, the _build directory before the `docker run`
command, there should always be an existing directory owned by the host
user for docker to bind /data-out to (ignoring the case of an existing
_build directory the current user does not have permission to write to),
avoiding the issue where it cannot write the output.
TEST: make -C util/docker docker-build-docs completes without issues
with and without an existing Documentation/_build directory
Change-Id: I6be9bc1fdca48f4d924f5c07cc261189ab6862fd
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81127
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Input file is parsed for FMAP and SMMSTORE region which is used if
found. Otherwise, the whole file is assumed to be the region. Passing
an image with FMAP that lacks SMMSTORER is an error.
Change-Id: Ieab555d7bbcfa4dadf6a5070d1297acd737440fb
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Offline SMMSTORE variable modification tool. Can be used to
pre-configure ROM image or debug EFI state stored in a dump.
Change-Id: I6c1c06f1d0c39c13b5be76a3070f09b715aca6e0
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Intel Firmware Support Package 2.4 specification (document 736809)
brings some significant changes compared to version 2.3 (document
644852):
1. It supports FSP-M multi-phase init. Some fields have been added to
the FSP header data structure for this purpose.
2. The `FSPM_ARCH2_UPD' and `FSPS_ARCH2_UPD' data structures must be
used in place of `FSPM_ARCH_UPD' and `FSPS_ARCH_UPD' respectively.
3. It support 64-bits FSP but 64-bits support will be provided by
subsequent patch.
Note that similarly to what is done for silicon initialization,
timestamps and post-codes are used during the memory initialization
multi-phase.
[736809]
https://cdrdv2-public.intel.com/736809/736809_FSP_EAS_v2.4_Errata_A.pdf
[644852]
https://cdrdv2-public.intel.com/644852/644852_2.3_Firmware-Support-Package-External-Architecture-Specification.pdf
TEST=verified on Lunar Lake RVP board (lnlrvp)
Change-Id: I1c24d26e105c3dcbd9cca0e7197ab1362344aa97
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
Align with the function integrating PSP FWs. And it is the integration
function's responsibility.
TEST=Identical test on all AMD platforms
Change-Id: I1a98614f3a5756a462b01085e9565b52cf9a9343
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Cleanup the messy code. The code left in main is all about filling
tables.
To help to do this,
1. Some local variables are put into global struct.
2. Add some functions. Set some functions to global.
TEST=Identical test on all AMD platforms
Change-Id: Ia25c3fd5de7ae48054359f0f6551d91d7a4f6828
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The space defined by size of the L1 table can not overlap with ISH
header. For other cases, the size defines the directory and its
content.
The PSP spec does not say it quite clearly. This change is partly
based on guess and can make extraction tool work so far.
Change-Id: Id4fbc6d57d7ea070a9478649a96af92be9441289
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This changes the virt target so that it can be run with the -bios option
and a pflash backend for the flash. QEMU can now be run as follows:
qemu -M virt -m 1G -nographic -bios build/coreboot.rom \
-drive if=pflash,file=./build/coreboot.rom,format=raw
coreboot will start in DRAM, but still have a flash to put CBFS onto and
to load subsequent stages and payload from.
Tested bootflow:
coreboot -> OpenSBI -> Linux -> u-root
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I009d97fa3e13068b91c604e987e50a65e525407d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: ron minnich <rminnich@gmail.com>
Reviewed-by: Philipp Hug <philipp@hug.cx>
|
|
Change-Id: I4cfec13cbc2a86dc352758541cce915a838e0d0f
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78305
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is for next CL to move the write_body to another source,
handle_file.c.
https://review.coreboot.org/c/coreboot/+/78305
Removing amdfwtool_cleanup in write_body will not change the
result. Write_body returns to main and amdfwtool_cleanup still ends up
getting called.
Change-Id: I639828498fa45911f430500735e90ddc198b6af5
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78304
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Darwin's getopt does not support the same parameters as the
util-linux version and so it is not possible to commit any
changes because lint fails.
Change-Id: Ife26083d2de080af9ed3d509945720051ca14bd7
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80436
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When updating the Makefiles, to keep from having to update two files at
the same time, import Makefile.mk into the external Makefile. This
allows the bulk of the settings to be in a single location.
While I'm here, I adjusted the print statements to match the rest of
coreboot.
Change-Id: Id5b869f49b34b22e6a02fc086e7b42975141a87e
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This is needed to build opensil. With meson and ninja added to the
coreboot-sdk image there is no need have them in the jenkins node image.
Change-Id: I36188ae895f2a770f1dc4528f332c09bf386db73
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
When we're building non-AMD processors, don't bother building amdfwtool
unless we're specifically building all of the tools like for abuild.
Change-Id: I9021674a06d65a79e24020790d317ab947c505fe
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80714
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I17758e23da25d610a0b462dfd388c53b89315242
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: I773fb39801f180fead584942dfb385fcde9d2680
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80262
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: ron minnich <rminnich@gmail.com>
|
|
Change-Id: Ifed410f4b7fdc358535f01850328c642d19ff1f6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: I6e9b2dac6fed702e8e353290971699cb9ee05dfc
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: I6b027ed39d3ee81878e069142c2d7212f3dc0a6f
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Thomas Heijligen <src@posteo.de>
|
|
SELF has the fields wired up for 64bit, but adding flat images cuts the
upper half.
Change-Id: I3b48b8face921e942fb0e01eace791ad3e1669a0
Signed-off-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80576
Reviewed-by: ron minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
currently the HiFive Unmatched mainboard produces the following error:
```
util/crossgcc/xgcc/lib/gcc/riscv64-elf/13.2.0/rv64imafdc/lp64d/libgcc.a
(_clzsi2.o): in function `__clzdi2':
util/crossgcc/gcc-13.2.0/libgcc/libgcc2.c:690:(.text+0x1e): relocation
truncated to fit: R_RISCV_HI20 against symbol `__clz_tab' defined in
.rodata section in util/crossgcc/xgcc/lib/gcc/riscv64-elf/13.2.0/
rv64imafdc/lp64d/libgcc.a(_clz.o)
```
This is due to the fact that the libgcc.a library is compiled with the
medlow code model but the mainboards are compiled with the medany code
model.
Changing the code model of the GCC libraries to the medany code model
fixes the issue.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: If5f07ce034686dd7fec160ea76838507c0ba7fa0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80139
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: ron minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since linux commit f9ba70535dc12d9eb57d466a2ecd749e16eca866
"[PATCH] Increase number of e820 entries hard limit from 32 to 128"
made in 2005 the number of e820 entries passed from the bootloader
is 128. Use the boot protocol version to check for support of
128 entries and use them if necessary.
Tested on IBM/SBP1:
Fixes booting a Linux payload when more than 32 entries are present
in the memory table, which can easily happen on a 4 socket platform.
Change-Id: Iec0a832fff091b6c3ae7050ef63e743a30618f25
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marvin Drees <marvin.drees@9elements.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
These strings didn't match the license names exactly, so update them
to match.
Change-Id: Ib946eb15ca5fa64cbd6b657350b989b4a4c1b7b7
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Platform has argument, but has_arg was mistakenly set to 0.
Change-Id: I7d5c31c2b1da544cb73d9e213d463332fcdba7df
Signed-off-by: Vojtech Vesely <vojtech.vesely@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80432
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marvin Drees <marvin.drees@9elements.com>
|
|
This tool doesn't have a makefile, when trying to compile it manually
with the given instructions it even fails to compile after fixing the
paths in the given command, and it references the non-existing
PCI_BUS_SEGN_BITS Kconfig symbol, so just drop this.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8ca75db281a215bf3f194ab72a107f666dc0694e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79934
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The device IDs were taken from the 200 series datasheet (page 24).
Change-Id: I34b5cb61dd7b561778cc8506858cd436e6f04f9a
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80419
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GMP and IASL don't compile with the default compiler and linker flags:
- GMP's check for the MacOS architecture hard coded x86_64 but it also
needs to know about arm64.
- iasl does some trickery on pointer alignment to save space(?), so we
need to tell clang about it.
Change-Id: If4cca9d3e55051a6121d992e5320bee1df17af9f
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80435
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Just a memory leak fix in Linux 6.7.
Change-Id: I1ff302dafa01e78429a30ff18e21ffe0b45ce46e
Signed-off-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80263
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This patch switches the cbmem utility from its own IP checksum
implementation to the commonlib version (which is good because the old
one had a couple of bugs: doesn't work on odd sizes and may overflow
its carry accumulator with input larger than 64K).
Change-Id: I0bef2c85c37ddd3438b7ac6389e9daa3e4955b31
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80256
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds support for the new command-line option `-E` to
the ifdtool, which enables users (primarily factory users) to
protect GPR0.
Additionally, this patch refactors some code while adding support for
enabling GPR0 protection.
For more information on the scope of GPR0 (General Protection Range 0),
please refer to the Intel Meteor Lake-U Type 4 Client Platform SPI
Programming Guide, Document Number 768150.
BUG=b:270275115
TEST=Able to test GPR0 protection on google/rex and google/yahiko.
> ifdtool -p mtl -E image.bin -O image.bin_lock
...
Value at GPRD offset (64) is 0x83220004
--------- GPR0 Protected Range --------------
Start address = 0x00004000
End address = 0x00322fff
...
GPR0 protection is now enabled
Change-Id: I27c533ae4109c79299f4e7ff75e750d7cc64280f
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
This renames bus to upstream and link_list to downstream.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I80a81b6b8606e450ff180add9439481ec28c2420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
GCC_OPTIONS is only used for target specific options right now,
so rename to TARGET_GCC_OPTIONS and only use them in the
non-bootstrap build.
Adapt BINUTILS_OPTIONS for consistency, even though it doesn't
have the same problem.
Change-Id: I5e4f54b758dd7daf4e69101c19dfa1212fa64cf6
Signed-off-by: Patrick Georgi <patrick@georgi.software>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80229
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id86ebc20cf5af5b65812c3f09235d0cba86d13f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80126
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Multiple links are unused throughout the tree and make the code more
confusing as an iteration over all busses is needed to get downstream
devices. This also not done consistently e.g. the allocator does not
care about multiple links on busses. A better way of dealing multiple
links below a device is to feature dummy devices with each their
respective bus.
This drops the sconfig capability to declare the same device multiple
times which was previously used to declare multiple links.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Iab6fe269faef46ae77ed1ea425440cf5c7dbd49b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78328
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jincheng Li <jincheng.li@intel.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This patch refactors GPR0 unlock function to add few important
logic as below
1. Perform GPR0 unlock if GPR0 is locked.
2. While unlocking dump the GPRD PCH strap details
3. Additionally, print the GPR start and end range if GPR0
protection is enabled.
TEST=Able to test GPR0 protection on google/rex and google/yahiko.
Exp 1: Trying to unlock GPR0 protection for a locked image
> ifdtool -p mtl -g image.bin -O image.bin_unlock
File image.bin is 33554432 bytes
Value at GPRD offset (64) is 0x83220004
--------- GPR0 Protected Range --------------
Start address = 0x00004000
End address = 0x00322fff
Writing new image to image.bin_unlock
Exp 2: Trying to unlock GPR0 protection for a unlocked image
> ifdtool -p mtl -g image.bin_unlock -O image.bin_unlock
File image.bin_unlock is 33554432 bytes
GPR0 protection is already disabled
Change-Id: Id35ebdefe83182ad7a3e735bdd2998baa0ec3ed7
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80216
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib69236fb5d68272f92405512dc231fa75ecccaa6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ieaf7894f49a90f562b164924cc025e3eab5a3f7f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
