| Age | Commit message (Collapse) | Author |
|---|
|
Two bits indicate OK and BAD for each operation PROBE READ ERASE WRITE.
8 bits out of 32 are in use now. No bits set means nothing has been tested.
For chips with at least one operation that is not tested or not working, the
user is asked to email a report to a special email adress so that the table
can be updated.
All chips are TEST_UNTESTED for now.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3277 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3275 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
devices, because they need an unlock command first.
For this reason, ST M50FLW support is moved to a
new HW support module, because any change in jedec.c
would bear the risk to cause problems with the already
supported devices.
It's already tested with ST M50FLW080A; the other
chips of this family i dont have available, so i couldnt
test it.
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3274 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
flashchips table. The read pointer was already checked properly.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3273 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
layout option, as well as areas, whose flash contents already contain the
desired data, will be skipped.
These ensures absolute data security of critical areas (BIOS boot block),
e.g. against a sudden power off or a CPU hangup during flashing. As a
nice side effect, it speeds up the flash process, if the BIOS to be flashed
is very similar to the version in flash.
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3260 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3221 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3167 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Support for the Winbond W39V080FA series of chips.
Support for flashing on the Kontron 986LCD-M board.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3166 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Support for flashing on the Kontron 986LCD-M board.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3165 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
(trivial)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3153 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3152 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
mechanism.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3151 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3146 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
of not being able to erase the chip.
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3145 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
ICH* chipsets. Functionality (except printing) should be unchanged.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Ward says:
This code detects the ICH8 chipset on my laptop, and it appears to use
SPI.
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3144 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3142 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3141 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3140 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Cosmetic changes in some files, partly bending the 80-characters-per-line
rule in this special case, as the 80-character-limited version looks
equally crappy even in an 80x25 console/xterm, so let's make it at least
look good in a high-resolution xterm.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3139 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3138 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3137 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
been used in the last few years, and the contents are available in
the README already anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3134 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
ROM chips, chipsets, and mainboards (Closes #90).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3133 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Stefan Reinauer for coresystems GmbH in 2005, as confirmed on IRC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3126 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also add a comment about NULL subsystem IDs leaving the board entry out
of auto-detection logic.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3110 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
specifying custom CFLAGS/LDFLAGS from the make command line like:
make CFLAGS="..." LDFLAGS="..."
I need to do this when building flashrom in a cross compiler environment
like buildroot for a foreign target.
Signed-off-by: Clark Rawlins <clark@bit63.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3102 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Remove the "enable write to flash" message, as the caller appears to
already report that.
- Move the 'modprobe msr' suggestions to the first lseek64 error handling, as
we get an error there already.
- Rename a perror string from "read" to "read msr", as we use the latter
already in this function for another read.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3101 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3099 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, move a big code comment to the top of enable_flash_cs5536().
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3098 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
CS5536 that have the Boot ROM on NOR flash that is directly connected to
FLASH_CS3 (Boot Flash Chip Select).
We need to write enable it in the NORF_CTL MSR register for flashrom to
be able to write to it, including JEDEC probe commands.
This patch allows us to stop using AMD gx_utils.ko for BIOS flashing on
the DBE61.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3097 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Programmable Micro Corp (PMC) need this.
Both the serial and parallel flash JEDEC detection routines would
benefit from a parity/sanity check of the vendor ID. Will do this later.
Add support for the PMC Pm25LV family of SPI flash chips.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Chris Lingard <chris@stockwith.co.uk>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3091 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
one board name that matches. The full syntax still works, and is required
when two vendors have boards with the same names.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3082 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3080 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Peter Stuge <peter@stuge.se>
Tested on the pcengines alix1c and works fine.
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3078 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
working.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3074 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
I've tested and verified the chip myself, and it seems to work
everything like supposted, since Carl-Daniel has patched flashrom to
use the read funktion on verifying.
"benchvice flashrom # ./flashrom -m gigabyte:m57sli -v test.4mb
Calibrating delay loop... OK.
No coreboot table found.
Found chipset "NVIDIA MCP55", enabling flash write... OK.
Found board "GIGABYTE GA-M57SLI-S4": enabling flash write...
Serial flash segment 0xfffe0000-0xffffffff enabled
Serial flash segment 0x000e0000-0x000fffff enabled
Serial flash segment 0xffee0000-0xffefffff disabled
Serial flash segment 0xfff80000-0xfffeffff enabled
LPC write to serial flash enabled
serial flash pin 29
OK.
MX25L3205 found at physical address 0xffc00000.
Flash part is MX25L3205 (4096 KB).
Flash image seems to be a legacy BIOS. Disabling checks.
Verifying flash... VERIFIED.
benchvice flashrom # ls -l test.4mb
-rw-r--r-- 1 root root 4194304 22. Jan 16:27 test.4mb
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3072 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
access instead. That fails if the flash chip is not mapped completely.
If the read function is set in struct flashchip, use it for verification
as well.
This fixes verification of all SPI flash chips >512 kByte behind an
IT8716F flash translation chip.
"MX25L8005 found at physical address 0xfff00000.
Flash part is MX25L8005 (1024 KB).
Flash image seems to be a legacy BIOS. Disabling checks.
Verifying flash... VERIFIED."
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Harald Gutmann <harald.gutmann@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3070 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
programming.
Minor formatting changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Harald Gutmann <harald.gutmann@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3069 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
readcnt==0 saves 10 seconds with the unconditional 10us delay, reducing
programming time for SST25VF016B to 40-45 secs.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3068 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
are already in use, the patch uses 'R' (for release) and, of course,
'--version'.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Acked-by: Ulf Jordan <jordan@chalmers.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3067 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Super I/O performing LPC-to-SPI flash translation.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3061 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3059 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3058 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3054 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
After the patch [...] The line length is still below 80 characters.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Acked-by: Torsten Duwe <duwe@lst.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3045 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3042 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Straight from the data sheet, not tested.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3036 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3033 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
unknown.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3032 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
exactly the same ID. Improve model number printing.
Add EN29F002(A)(N)B support while I'm at it.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Markus Boas <bios@ryven.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3031 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The continuation ID code does not go further than checking for IDs of
the type 0x7fXX, but does this for vendor and product ID. The current
published JEDEC spec has a list where the largest vendor ID is 7 bytes
long, but all leading bytes are 0x7f. The list will grow in the future,
and using a 64bit variable will not be enough anymore.
Besides that, it seems that the location of the ID byte after the first
continuation ID byte is very vendor specific, so we may have to revisit
that code some time in the future.
(Suggestion for a new encoding:
Use a two-byte data type for the ID, the lower byte contains the only
non-0x7f byte, the upper byte contains the number of 0x7f bytes used as
prefix, which is the bank number minus 1 the vendor ID appears in.)
Add support for EON EN29F002AT.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3030 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
(JEP106W), adds some device IDs and provides information about
non-conforming IDs.
The EON change is left to the patch adding EON chips.
This patch should have no effect on code generation.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3029 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
page size. Fix that. Page size is uniform 256 bytes for SPI.
A sector/block size field in struct flashchip would be nice, though.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3027 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
output is specified.
Pretty-print the chip status register (including block lock information)
for ST M25P family and Macronix MX25L family chips.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3026 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
data sheet.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3025 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
M25P64, M25P128 to flashrom. ST M25P80 support is already there.
Not tested, but conforming to data sheets and double checked.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
with multiple possible opcodes from linear numbering at the end (_1, _2)
to include the opcode at the end (_60, _c7). That way, you only have to
take a short look at the data sheet and choose the right function by
appending the opcode listed in the data sheet.
No functional changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Print status register before erase to help debugging block locks.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3008 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
AT49F002
AT49F002N
AT49F002T
AT49F002NT
Only tested the read function on AT49F002T.
datasheet @ http://www.atmel.com/atmel/acrobat/doc1017.pdf
Signed-off-by: Frederico Silva <frederico.silva@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3003 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, s/0xFF80/0xFFC0/ in the Acorp 6A815EPD board-enable, as per
http://www.linuxbios.org/pipermail/linuxbios/2007-December/027750.html
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2997 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2995 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Attached is a patch that enables AMD Geode CS5536 chipset support. I
have tested it successfully on a MSM800 board from digital logic.
Signed-off-by: Lane Brooks <lbrooks@mit.edu>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2967 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
a delay of 10 us after entering ID mode and this was insufficient for
the 29C020. The data sheet claims we have to wait 10 ms, but tests have
shown that 20 us suffice. Allow for variations in chip delays with a
factor of 2 safety margin.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Add support for the Fujitsu MBM29F400TC flash part.
Detection and reading works, writing is not tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2903 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Looking through the sources of Uniflash utility I found that this chip
is no more no less than low-voltage variant of Am29F040B but with
different ID.
So I created a very quick patch (attached).
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2897 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2884 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
them yet.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2881 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
status register instead.
This has been tested by Harald Gutmann <harald.gutmann@gmx.net> with a
MX25L4005 chip.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2876 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2875 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
chip the code was tested and verified with is the Macronix MX25L4005,
but other chips should work as well.
Timeouts are still hardcoded to data sheet maxima, but the status
register checking code is already there.
Thanks to Harald Gutmann for the initial code on which this is loosely
based.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2874 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2873 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Ed Swierk in
http://www.mail-archive.com/linuxbios@linuxbios.org/msg09788.html .
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2868 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Install binary in /usr/sbin (not /usr/bin), as it's a root-only tool.
- Rename manpage from flashrom.1 to flashrom.8, as section 8 contains
"System administration commands (usually only for root)".
- Actually install the manpage upon 'make install'.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2866 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Michael van der Kolff <mvanderkolff@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
applying abstraction and wrapping.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2863 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Move SPI code out of board_enable.c where it started its life. The SPI
chip finding and SPI chip accessor code is moved as well. This can be
split later if we feel like it.
The non-use of svn cp is intentional because the only history we'd have
to preserve are a few commits which were early prototypes of chip
identification code. For those who intend to look at that history, they
can look at board_enable.c revision 2853.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2858 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
chip finding and SPI chip accessor code is moved as well. This can be
split later if we feel like it.
The non-use of svn cp is intentional because the only history we'd have
to preserve are a few commits which were early prototypes of chip
identification code. For those who intend to look at that history, they
can look at board_enable.c revision 2853.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2857 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
day :-)
Also minor changes to remove tab-space combinations where possible.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <david.hendricks@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Index: jedec.c
===================================================================
--- jedec.c (revision 2847)
+++ jedec.c (working copy)
@@ -281,7 +281,7 @@
// dumb check if erase was successful.
for (i = 0; i < total_size; i++) {
if (bios[i] != (uint8_t) 0xff) {
- printf("ERASE FAILED\n");
+ printf("ERASE FAILED @%d, val %02x\n", i, bios[i]);
return -1;
}
}
Index: board_enable.c
===================================================================
--- board_enable.c (revision 2847)
+++ board_enable.c (working copy)
@@ -153,7 +153,8 @@
return 1;
}
/* Start IO, 33MHz, readcnt input bytes, writecnt output bytes. Note:
- We can't use writecnt directly, but have to use a strange encoding */
+ * We can't use writecnt directly, but have to use a strange encoding
+ */
outb((0x5 << 4) | ((readcnt & 0x3) << 2) | (writeenc), port);
do {
busy = inb(port) & 0x80;
@@ -202,43 +203,39 @@
/*
* Helper functions for many Winbond Super I/Os of the W836xx range.
*/
-#define W836_INDEX 0x2E
-#define W836_DATA 0x2F
-
/* Enter extended functions */
-static void w836xx_ext_enter(void)
+static void w836xx_ext_enter(uint16_t port)
{
- outb(0x87, W836_INDEX);
- outb(0x87, W836_INDEX);
+ outb(0x87, port);
+ outb(0x87, port);
}
/* Leave extended functions */
-static void w836xx_ext_leave(void)
+static void w836xx_ext_leave(uint16_t port)
{
- outb(0xAA, W836_INDEX);
+ outb(0xAA, port);
}
/* General functions for reading/writing Winbond Super I/Os. */
-static unsigned char wbsio_read(unsigned char index)
+static unsigned char wbsio_read(uint16_t index, uint8_t reg)
{
- outb(index, W836_INDEX);
- return inb(W836_DATA);
+ outb(reg, index);
+ return inb(index+1);
}
-static void wbsio_write(unsigned char index, unsigned char data)
+static void wbsio_write(uint16_t index, uint8_t reg, uint8_t data)
{
- outb(index, W836_INDEX);
- outb(data, W836_DATA);
+ outb(reg, index);
+ outb(data, index+1);
}
-static void wbsio_mask(unsigned char index, unsigned char data,
- unsigned char mask)
+static void wbsio_mask(uint16_t index, uint8_t reg, uint8_t data, uint8_t mask)
{
- unsigned char tmp;
+ uint8_t tmp;
- outb(index, W836_INDEX);
- tmp = inb(W836_DATA) & ~mask;
- outb(tmp | (data & mask), W836_DATA);
+ outb(reg, index);
+ tmp = inb(index+1) & ~mask;
+ outb(tmp | (data & mask), index+1);
}
/**
@@ -248,37 +245,80 @@
* - Agami Aruma
* - IWILL DK8-HTX
*/
-static int w83627hf_gpio24_raise(const char *name)
+static int w83627hf_gpio24_raise(uint16_t index, const char *name)
{
- w836xx_ext_enter();
+ w836xx_ext_enter(index);
/* Is this the w83627hf? */
- if (wbsio_read(0x20) != 0x52) { /* SIO device ID register */
+ if (wbsio_read(index, 0x20) != 0x52) { /* Super I/O device ID register */
fprintf(stderr, "\nERROR: %s: W83627HF: Wrong ID: 0x%02X.\n",
- name, wbsio_read(0x20));
- w836xx_ext_leave();
+ name, wbsio_read(index, 0x20));
+ w836xx_ext_leave(index);
return -1;
}
/* PIN89S: WDTO/GP24 multiplex -> GPIO24 */
- wbsio_mask(0x2B, 0x10, 0x10);
+ wbsio_mask(index, 0x2B, 0x10, 0x10);
- wbsio_write(0x07, 0x08); /* Select logical device 8: GPIO port 2 */
+ wbsio_write(index, 0x07, 0x08); /* Select logical device 8: GPIO port 2 */
- wbsio_mask(0x30, 0x01, 0x01); /* Activate logical device. */
+ wbsio_mask(index, 0x30, 0x01, 0x01); /* Activate logical device. */
- wbsio_mask(0xF0, 0x00, 0x10); /* GPIO24 -> output */
+ wbsio_mask(index, 0xF0, 0x00, 0x10); /* GPIO24 -> output */
- wbsio_mask(0xF2, 0x00, 0x10); /* Clear GPIO24 inversion */
+ wbsio_mask(index, 0xF2, 0x00, 0x10); /* Clear GPIO24 inversion */
- wbsio_mask(0xF1, 0x10, 0x10); /* Raise GPIO24 */
+ wbsio_mask(index, 0xF1, 0x10, 0x10); /* Raise GPIO24 */
- w836xx_ext_leave();
+ w836xx_ext_leave(index);
return 0;
}
+static int w83627hf_gpio24_raise_2e(const char *name)
+{
+ return w83627hf_gpio24_raise(0x2d, name);
+}
+
/**
+ * Winbond W83627THF: GPIO 4, bit 4
+ *
+ * Suited for:
+ * - MSI K8N-NEO3
+ */
+static int w83627thf_gpio4_4_raise(uint16_t index, const char *name)
+{
+ w836xx_ext_enter(index);
+ /* Is this the w83627thf? */
+ if (wbsio_read(index, 0x20) != 0x82) { /* Super I/O device ID register */
+ fprintf(stderr, "\nERROR: %s: W83627THF: Wrong ID: 0x%02X.\n",
+ name, wbsio_read(index, 0x20));
+ w836xx_ext_leave(index);
+ return -1;
+ }
+
+ /* PINxxxxS: GPIO4/bit 4 multiplex -> GPIOXXX */
+
+ wbsio_write(index, 0x07, 0x09); /* Select logical device 9: GPIO port 4 */
+
+ wbsio_mask(index, 0x30, 0x02, 0x02); /* Activate logical device. */
+
+ wbsio_mask(index, 0xF4, 0x00, 0x10); /* GPIO4 bit 4 -> output */
+
+ wbsio_mask(index, 0xF6, 0x00, 0x10); /* Clear GPIO4 bit 4 inversion */
+
+ wbsio_mask(index, 0xF5, 0x10, 0x10); /* Raise GPIO4 bit 4 */
+
+ w836xx_ext_leave(index);
+
+ return 0;
+}
+
+static int w83627thf_gpio4_4_raise_4e(const char *name)
+{
+ return w83627thf_gpio4_4_raise(0x4E, name);
+}
+/**
* Suited for VIAs EPIA M and MII, and maybe other CLE266 based EPIAs.
*
* We don't need to do this when using LinuxBIOS, GPIO15 is never lowered there.
@@ -335,12 +375,12 @@
pci_write_byte(dev, 0x59, val);
/* Raise ROM MEMW# line on Winbond w83697 SuperIO */
- w836xx_ext_enter();
+ w836xx_ext_enter(0x2E);
- if (!(wbsio_read(0x24) & 0x02)) /* flash rom enabled? */
- wbsio_mask(0x24, 0x08, 0x08); /* enable MEMW# */
+ if (!(wbsio_read(0x2E, 0x24) & 0x02)) /* flash rom enabled? */
+ wbsio_mask(0x2E, 0x24, 0x08, 0x08); /* enable MEMW# */
- w836xx_ext_leave();
+ w836xx_ext_leave(0x2E);
return 0;
}
@@ -487,9 +527,11 @@
{0x10de, 0x0360, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
"gigabyte", "m57sli", "GIGABYTE GA-M57SLI", it87xx_probe_serial_flash},
{0x1022, 0x7468, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
- "iwill", "dk8_htx", "IWILL DK8-HTX", w83627hf_gpio24_raise},
+ "iwill", "dk8_htx", "IWILL DK8-HTX", w83627hf_gpio24_raise_2e},
+ {0x10de, 0x005e, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
+ "msi", "k8n-neo3", "MSI K8N Neo3", w83627thf_gpio4_4_raise_4e},
{0x1022, 0x746B, 0x1022, 0x36C0, 0x0000, 0x0000, 0x0000, 0x0000,
- "AGAMI", "ARUMA", "agami Aruma", w83627hf_gpio24_raise},
+ "AGAMI", "ARUMA", "agami Aruma", w83627hf_gpio24_raise_2e},
{0x1106, 0x3177, 0x1106, 0xAA01, 0x1106, 0x3123, 0x1106, 0xAA01,
NULL, NULL, "VIA EPIA M/MII/...", board_via_epia_m},
{0x1106, 0x3177, 0x1043, 0x80A1, 0x1106, 0x3205, 0x1043, 0x8118,
@@ -509,8 +551,8 @@
* Match boards on LinuxBIOS table gathered vendor and part name.
* Require main PCI IDs to match too as extra safety.
*/
-static struct board_pciid_enable *board_match_linuxbios_name(char *vendor,
- char *part)
+static struct board_pciid_enable *board_match_linuxbios_name(char *vendor,
+ char *part)
{
struct board_pciid_enable *board = board_pciid_enables;
@@ -525,10 +567,11 @@
continue;
if (board->second_vendor &&
- !pci_dev_find(board->second_vendor, board->second_device))
+ !pci_dev_find(board->second_vendor, board->second_device))
continue;
return board;
}
+ printf("NOT FOUND %s:%s\n", vendor, part);
return NULL;
}
@@ -545,20 +588,20 @@
continue;
if (!pci_card_find(board->first_vendor, board->first_device,
- board->first_card_vendor,
- board->first_card_device))
+ board->first_card_vendor,
+ board->first_card_device))
continue;
if (board->second_vendor) {
if (board->second_card_vendor) {
if (!pci_card_find(board->second_vendor,
- board->second_device,
- board->second_card_vendor,
- board->second_card_device))
+ board->second_device,
+ board->second_card_vendor,
+ board->second_card_device))
continue;
} else {
if (!pci_dev_find(board->second_vendor,
- board->second_device))
+ board->second_device))
continue;
}
}
@@ -582,7 +625,7 @@
if (board) {
printf("Found board \"%s\": Enabling flash write... ",
- board->name);
+ board->name);
ret = board->enable(board->name);
if (ret)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2850 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2847 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2846 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The help implied that writes happen by default, which they don't. Fix
the text, and say something when we dont specify any commands.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2820 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
way. It introduces a generic SPI host driver for the IT8716F Super I/O
which will enable easy SPI programming without having to care for the
peculiarities of the SPI host.
To activate probing for the IT8716F, you have to use the gigabyte:m57sli
mainboard override. SPI support will then use the gathered SPI host data
to access the SPI flash.
This has been tested sucessfully by Ward Vandewege <ward@gnu.org> on the
GA-M57SLI v2.0, which has a MX25L4005 SPI flash part.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2817 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
to ITE IT8716F Super I/O. Right now this is hardcoded to the Gigabyte
M57SLI board. It works only with rev 2.0 of the board, but it will bail
out on earlier versions, so no damage can occur.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2811 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
sis630 chipset enable.
Signed-off-by: Alex Beregszaszi <alex@rtfs.hu>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2770 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2769 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2768 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
I'm self-ack'ing this, as the origin of the code in udelay.c (and thus
the license and copyright owner) is pretty clear.
The code which is now in udelay.c was split out from flash_rom.c in r1428,
and flash_rom.c, in turn, has been around since the beginning and had a
'Copyright 2000 Silicon Integrated System Corporation' line as well as the
usual GPLv2-or-later license header.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2767 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
project (being packaged by distros, among other things).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2764 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Markus Boas <ryven@ryven.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2753 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Markus Boas <ryven@ryven.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2752 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
No changes in content of the files.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2751 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2748 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2747 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2746 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2745 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The first byte of the flash chip was read at the start of the function
and later written back to address 0 if the flash chip was not identified
as SST28SF040, which means most of the time. This write caused corruption
of flash contents when verifying a SST49LF160C part.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2744 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2743 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2742 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
M50FLW080B, M50FW080, M50FW016, M50LPW116, M29W010B flash chips made
by ST to flashrom.
The patch is based on the data sheets of the chips and has not been
tested at all.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2741 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Only reading from the chips was tested; writing support is untested.
Thanks to Gürkan Sengün <gurkan@linuks.mine.nu> for testing!
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2740 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
