| Age | Commit message (Collapse) | Author |
|---|
|
- Add placeholder USB phy settings, needs tuning still
- Change UART2 to be skipped during FSP init
- Update headphone codec irq to be level triggered as
that is how the kernel is configuring it
BUG=chrome-os-partner:40635
BRANCH=none
TEST=emerge-glados coreboot
Change-Id: I9a15a27dab49d4e19f8ef0574ee2e61ae90c99fc
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 6e7a0032ba23d6762342639c2c7cb877c1f90452
Original-Change-Id: Ie1439f21116022b0644d06853df9490e4651a9ae
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/304926
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12149
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the config option for TPM to use PIRQ instead of SERIRQ
and enable the MAINBOARD_HAS_LPC_TPM option.
BUG=chrome-os-partner:40635
BRANCH=none
TEST=emerge-glados coreboot
Change-Id: I990901117a2c478045c403f1039d6eedfc278255
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 44ecaaae1eb482ef5d4cf1e051de4571cc4441be
Original-Change-Id: I115d468c72c3fd015abdddffdd1626368bfedb6e
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/304925
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12148
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
With SPI TPMs there is no SERIRQ for interrupts, instead it is
a PIRQ based interrupt. The TCG PC Client Platform TPM Profile
Specification says it must be active low and shared.
This can be enabled with the CONFIG_TPM_PIRQ option that will
specify the interrupt vector to report for the TPM.
BUG=chrome-os-partner:40635
BRANCH=none
TEST=verify TPM interrupt functionality in /proc/interrupts on glados
Change-Id: Iad3ced213d1fc5380c559f50c086206dc9f22534
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: abdd0b8ecdf51ff32ed8bfee0823bbc30d5d3d49
Original-Change-Id: If7d22dfcfcab95dbd4c9edbd8674fc8d948a62d2
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/304133
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12147
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Implemented Device IRQ porgramming, PxRC to IRQ mapping,
GPIO IRQ routing, SCI IRQ select through UPD
BUG=NONE
BRANCH=NONE
CQ-DEPEND=CL:*232948
TEST= build and booted sklrvp,kunimitsu with this changes.
Change-Id: Ic98074491fe5251a48ed55b6fb7ef31809c3abf3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 534bd65e5df8654d745c8efe491a332336c9cdc3
Original-Change-Id: I4ea6f3cdb15d371c6023bfd046f3475290f5aa26
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/291403
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12146
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
FSP 1.7.0 provides UPD to configure USB phy settings
update the same for kunimitsu.
FSP 1.7.0 also provides UPD to indicate FSP not to reinitialise
UART2 controller during MemoryInit.
BRANCH=none
BUG=chrome-os-partner:45684,chrome-os-partner:41374,chrome-os-partner:42284
TEST=build for Kunimitsu, boot on FAB3, Also checked for Boot from USB,
Boot from eMMC, USB Audio, Onboard Audio, Touch, Wifi, S3 entry/resume
CQ-DEPEND=CL:303661
Change-Id: Ie0a545c954f472cc822b63786d40399ec93d5166
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 90296e04942c70d972c225fc75dfab6de44d10ed
Original-Change-Id: If79e81ef3323e782e96db307d89a01c14174b435
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Signed-off-by: Rishavnath Satapathy <rishavnath.satapathy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/304032
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12145
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
In FSP 1.7.0 SataMode and SataEnable have been moved from
MemoryInit to SiliconInit. Also, GpioTablePtr has been removed.
USB phy settings added to SiliconInit, Enable the configs for USB
equalization settings in coreboot.
Addition of serialIO UPD to indicate FSP not to reinitialise
UART2 controller during MemoryInit.
BRANCH=none BUG=chrome-os-partner:45684, chrome-os-partner:42284, chrome-os-partner:41374
TEST=build for Kunimitsu, boot on FAB3, Also checked for Boot from USB, Boot from eMMC,
USB Audio, Onboard Audio, Touch, Wifi, S3 entry/resume
CQ-DEPEND=CL:*232947, CL:*232946, CL:*232948, CL:*232949
Change-Id: I2e8e6e32fc7074774ddcf1fb4c270bb56372b7df
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 623c5a52f3afedaf2c0bfe7361cfd627d093cb73
Original-Change-Id: I8b3be2c49893c564fe2197aa32bde6323bf425e9
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Signed-off-by: Rishavnath Satapathy <rishavnath.satapathy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/303661
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12144
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch strengthens the Rcomp Target CTRL by 10% for
8GB memory part K4E6E304EE-EGCF as with the current values
the MRC training is failing due to more load on CS#
BRANCH=None
BUG=chrome-os-partner:44647
TEST=BUilds and boots on Kunimitsu.
Change-Id: I478002bbebabaac418356d4b5b4755bb56009268
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b208659e690d8cb5b8dcaf30eed53c01b9f77f6d
Original-Change-Id: Ia0a0c1358649af77a3a0d301cb791f26f1e039bf
Original-Signed-off-by: pchandri <preetham.chandrian@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/304103
Original-Commit-Ready: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Tested-by: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Preetham Chandrian <preetham.chandrian@intel.com>
Reviewed-on: http://review.coreboot.org/12143
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch implements the igd_opregion using the write_acpi_tables
mechanism to support GOP usage.
BRANCH=none
BUG=chrome-os-partner:44559
TEST=W/o GOP_SUPPORT in config, Built and boot on kunimitsu/glados.
W/ GOP_SUPPORT enabled, build and boot on kunimitsu/glados, but on
glados Dev screen can not be seen (OS display is fine).
CQ-DEPEND=CL:303539
Change-Id: I4cd63dfe0d3f456c5f084e38db976425143f79e7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4db57463a69c6114b1e2ed4035d378ee3a82783f
Original-Change-Id: I6f3c29c1b608eeaad8f2bf79d17394d49f8e412c
Original-Signed-off-by: robbie zhang <robbie.zhang@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/303387
Original-Commit-Ready: Robbie Zhang <robbie.zhang@intel.com>
Original-Tested-by: Robbie Zhang <robbie.zhang@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12142
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch provides the lb_framebuffer() for coreboot table with
fsp gop usage, add Igd Opregion register defines, and update the
UPD naming following fsp.
BRANCH=none
BUG=chrome-os-partner:44559
TEST=Built and boot on kunimitsu/glados.
Change-Id: I9cf9d991eb09d698e7a78323cd855c4c99b55eca
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cd6834057cca60716bc0e24cfc2cd60fed02be7a
Original-Change-Id: I64987e393c39a7cc1084edf59e7ca51b8c5ea743
Original-Signed-off-by: robbie zhang <robbie.zhang@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/303539
Original-Commit-Ready: Robbie Zhang <robbie.zhang@intel.com>
Original-Tested-by: Robbie Zhang <robbie.zhang@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12141
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This is to support other gfx enable method such as Gfx Peim (AKA GOP)
for Intel soc.
BRANCH=none
BUG=chrome-os-partner:44559
TEST=Built and boot on kunimitsu/glados.
Change-Id: Ib8010ea6901ea906a8b4129807b94ace71ef1165
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ad26a99560009c487070cccf6ab132188b9e247d
Original-Change-Id: Id132718a8bcec5446cc4c0d9d636d26e8a99bb15
Original-Signed-off-by: robbie zhang <robbie.zhang@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/303801
Original-Commit-Ready: Robbie Zhang <robbie.zhang@intel.com>
Original-Tested-by: Robbie Zhang <robbie.zhang@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12140
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Romstage handoff copied from cpu/intel/haswell/romstage.c
Change-Id: I1e1a67fa3c2c13cebcf8f0af318055b9d97d0a59
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11953
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Having an empty microcode file makes it more easy to debug
in comparison to a not existing file in cbfs. There are some
platforms (e.g. ep80579) which support microcode updates but
not having any microcode updates yet in our tree.
These platform hang the build because `cat` is called with no
parameters.
Change-Id: I2699bde0c62ae62ca888686f8b496e845c36d970
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/12109
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Activate the IOMMU support for the Asus F2A85-M.
Add the device to `devicetree.cb`.
$ lspci -s 0.2
[…]
00:00.2 IOMMU: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) I/O Memory Management Unit
$ dmesg
[…]
[ 0.000000] ACPI: IVRS 00000000bf144e10 00070 (v02 AMD AMDIOMMU 00000001 AMD 00000000)
[ 0.000000] ACPI: SSDT 00000000bf144e80 0051F (v02 AMD ALIB 00000001 MSFT 04000000)
[ 0.000000] ACPI: SSDT 00000000bf1453a0 006B2 (v01 AMD POWERNOW 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 00000000bf145a52 00045 (v02 CORE COREBOOT 0000002A CORE 0000002A)
[…]
Linux 3.10 reported several IO page faults, which could never be explained and
which the vendor firmware did not. These errors couldn’t be reproduced with
Linux 3.18 by Damien Zammit.
Change-Id: I0aa530be17d31656e65db6113343f2ea7008b843
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/3517
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I45eb03a4b351e458e8448245896743bd6fa57637
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11943
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The native AMD DDR3 memory initialization code was riddled with
numerous errors and was missing critical configuration code segments;
this made it so that DDR3 memory did not function on most AMD boards.
This patch corrects enough of the DDR3 initialization such that
UDIMMs can be used on most channels of G34 Opteron boards. Further
work is needed to fix the broken RDIMM code and remaining UDIMM issues.
Change-Id: Iab690db769e820600693ad1170085623b177b94e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11941
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
|
|
Change-Id: I88203907270db1a268bd377151f15c24fca1efdc
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11964
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
(this probably fixes relocate_sb_ht_chain() on tyan/s2885)
Change-Id: I5a26f4280b00bfb259c600048f6a7391a6c1268f
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10913
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This patch was tested with the following card:
IDE interface: Silicon Image, Inc. PCI0680 Ultra ATA-133 Host Controller [1095:0680] (rev 02)
Change-Id: I988b73684b54942d8ee6e44a9319dcc54086fca7
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/12171
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
In order to build stand alone verstage the chromeos.c
file needs to be part of the verstage target.
BRANCH=none
BUG=chrome-os-partner:44827
TEST=Build and run on kunimitsu
Change-Id: I9c547ae177dc95030c8c545a302a2349bf1c9cf8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 07b6465f0b3e18d30647959b8e1db44d8647cf90
Original-Change-Id: I49bf7f1bd2edb32ffe9cc22f6fce1348434fd234
Original-Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/301243
Original-Commit-Ready: Leroy P Leahy <leroy.p.leahy@intel.com>
Original-Tested-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12152
Tested-by: build bot (Jenkins)
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
|
|
It's no longer used.
BUG=none
BRANCH=none
TEST=it compiles
Change-Id: I3d9385e0e1f14977c1632f3a8dda771c684ce458
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5381b6434996da10706dd358928f98703ac0892c
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: Ib0cfaf1bb173a7150f7ff504b9f58a62eb82e781
Original-Reviewed-on: https://chromium-review.googlesource.com/302634
Reviewed-on: http://review.coreboot.org/12138
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
The 1392MHz value used to throttle the RK3288 earlier was somewhat
arbitrary. This patch brings the throttling in sync with the operating
points specified in the Linux device tree for RK3288.
BUG=chrome-os-partner:42054
BRANCH=none
TEST=Saw print statement in image.serial.bin indicating that APLL
was set to the desired frequency.
Change-Id: Ibe570267bbfe23f010ad5e1ea651356291b9c63c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a146f23b13cb0f6da93ada65648cf33ecfaaa7d6
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I6bcdb5fd6ffa3f9a22e79c519bdb7980492e2318
Original-Reviewed-on: https://chromium-review.googlesource.com/302633
Reviewed-on: http://review.coreboot.org/12137
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
BUG=chrome-os-partner:42054
BRANCH=none
TEST=tested with subsequent patch
Change-Id: I92d67ff4b706c16677661ead1edd5c190ccc6d95
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: dced0fcbc35457d7326d590948ce5fe098a5e735
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I7b29c647380046ac41a290b19fdfba186bcb2127
Original-Reviewed-on: https://chromium-review.googlesource.com/302632
Reviewed-on: http://review.coreboot.org/12136
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
This applies CL:300617 to Rialto to down throttle further in
recovery mode.
BUG=chrome-os-partner:42054
BRANCH=none
TEST=Saw print statment in recovery mode with image.serial.bin,
device only got mildly warm after several minutes (not hot).
Change-Id: I08b6024d31c83c6bbd8c8d9d9a07adc9835e81fd
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 74eb9143fbe13df5f386185eab9e5ba9df27cadf
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I9e57d826750cb523c115332fa13a6143bcff7449
Original-Reviewed-on: https://chromium-review.googlesource.com/302631
Reviewed-on: http://review.coreboot.org/12135
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
BUG=chrome-os-partner:41201
BRANCH=firmware-veyron
TEST=tested with subsequent patch on mickey
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I7081d92be128f522e1a33eee6f3de9dfbbf042ea
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a390c927ad8ed035520c8a813db808715dc5e527
Original-Change-Id: I3ce0f7b2772c8c652b7f461749d01cc7b669b6cf
Original-Reviewed-on: https://chromium-review.googlesource.com/300616
Original-Commit-Ready: David Hendricks <dhendrix@chromium.org>
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/12134
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
Change-Id: Id2230ecd800b138b6ccbbac318e71c9edf076c75
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12116
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ib078b21ddf0493ad6795c6ab79125b3917ff7049
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12115
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I45b3412263507d92f443743d2ee63c9a8ef94795
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12114
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The possibility of adding a bootsplash image to ROM should be independent
from VGA_ROM_RUN and VESA menuconfig options.
For example, the stored image could be saved in CBFS not for coreboot
but for later use in SeaBIOS.
Change-Id: I3a0ed53489c40d4d44bd4ebc358ae6667e6c797f
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/12129
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ieb27bd51dfd45dd15d24a576865d38180a07444e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12175
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I02c1fba5c749d5adb33ec86777bde108e587caa6
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12185
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
LPC decodes were not enabled, leading to a failure of POST 80 cards
and similar debugging devices. Enable the relevant LPC decodes
to allow debugging.
Additionally, the SMBUS controllers were not properly set up.
Enable both the primary and auxiliary controllers.
Finally, K10 and higher CPUs were hanging during boot due to
a misconfigued IOAPIC. Properly configure the IOAPIC.
Change-Id: I9ffb6542ce445ac971fb81f4f554e7f1313e6a98
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12177
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
TEST: Booted ASUS KGPE-D16 and verified device functionality.
Change-Id: Ic6f5b3ca86eb55dc04291be0db67d06c34c6a6dc
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12188
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: Ieccafe8864d622c651e6a524e9898505ded15e54
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12187
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Certain devices, such as the Intel 82575GB, contain multiple nested
PCIe bridges (for example the PES12N3A). Coreboot does not set
the primary bus number of the lower bridges, causing upstream
forwarding failure. This in turn causes coreboot to fail to find
the lowest devices (in this case the NICs), and as a result the
required resources are not allocated and the NICs do not function.
Change-Id: I4fd3aa21a04dbe89ac6a5995e7707af914d432b1
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12186
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I5139ee222a0dca7f8e62612a39d30cad7976b505
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12184
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: Iccd034f32c26513edd52ca3a11a30f61c362682d
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11940
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
|
|
Change-Id: Idf1db091f1d1e40ce2f248bc25d662cf9608b27e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12179
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I1d7d6715663a13ab94fd6d71808e35f0f7384d00
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11938
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I507c93556dd66c3590c8ca11c06cd5b2dd7884c5
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12176
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I37763a59d2546cd0c0e57b31fdb7aa77c2c50bee
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11937
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ia13ba58118a826e830a4dc6e2378b76110fcabad
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11939
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I3f1f33b50f788b6d57f1a7986c4bdb912426e4f0
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12125
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I9a59fcb7cf221ae590a047c520e7aff99e23ecf1
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11962
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Update mainboards using the w83795 sensor device with sane default
values. Note that in some cases the defaults may vary from the
defaults provided by the old driver, for example the default fan
speeds and control modes have changed as I do not have any information
on the correct sensor to fan mappings for these boards.
Change-Id: Id2ad6222d7a0f29483b022fa097d7d098c6b4122
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12124
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I5a9b5eba992853b84b0cb6c3a1764edf42ac49b2
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12080
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I29ece10eeefc2c75a3829c169f1e1aede7194ec2
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12079
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
Add full support for fan control, fan monitoring, and voltage
monitoring. Fan speeds and functions are configurable via
each mainboard's devicetree.cb file.
NOTE: This patch effectively rewrites large portions of
the original driver. You may need to re-verify correct
operation on your hardware if you were using the old
driver code.
Change-Id: I3e246af0e398d65ee43ea708060885c67fd7d202
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11936
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Certain devices (such as the LSI SAS 2008 controller) do not
respond to PCI probes immediately after link training. If it
is known that such a device is likely to be installed allow the
mainboard to insert an appropriate delay.
Change-Id: Ibcd9426628cacd6f88e6e3fcbc2b3eb7e3a92081
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11991
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
|
|
If an SMBUS device in devicetree.cb is placed under a parent device
that does not have an SMBUS controller, coreboot will enter an
infinite loop and hang without printing any failure messages.
Modify the loop to exit under these conditions, allowing the failure
message to be printed.
Change-Id: I4c615f3c5b3908178b8223cb6620c393bbfb4e7f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12131
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins)
|
|
The hudson chipset has 4 USB controllers, the fourth is USB1.1-only and
(presumably) not used very often, add support for hiding it:
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) USB1 (3.0, XHCI)
00:10.1 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03)
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB2 (2.0, OHCI+EHCI)
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB3 (2.0, OHCI+EHCI)
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB4 (1.1, OHCI only)
Change-Id: I804e7852fd0a6f870dd118b429473cb06ebac9a4
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7355
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
On my Foxconn nT-A3500 on cold boot the board doesn't survive the soft
reboot in the UsbRxMode path and the vendor bios doesn't touch this
Cg2Pll voltage setting either.
The fixup code for UsbRxMode in src/vendorcode/amd/cimx/sb800/SBPort.c
doesn't seem to "CG PLL multiplier for USB Rx 1.1 mode", but rather
lowers the Cg2Pll voltage from the hw default of 1.222V to 1.1V
by setting Cg2Pll_IVR_TRIM in CGPllConfig5 to 1000.
See also USB_PLL_Voltage which is only used in the UsbRxMode code path.
However if this is already the efuse/eprom default for the SB800 then
UsbRxMode is a no-op, so whether or not it gets executed depends on the
very exact hw revision of the southbridge chip and could change between
two instances of the same board.
UsbRxMode used to be unitialized and was first set to default to 1
in http://review.coreboot.org/6474 (change I32237ff9,
southbridge/amd/cimx/sb800: Uninitialized variables in config func):
> > Why initialize those to 1? (just curious)
> See src/vendorcode/amd/cimx/sb800/SBTYPE.h
> git grep 'SbSpiSpeedSupport\|UsbRxMode'
> src/vendorcode/amd/cimx/sb800/SBTYPE.h
I could not find a corresponding errata in the SB800 errata list,
however errata 15 (USB Resets Asynchronously With Port CF9h Hard Reset)
might play into this being unsafe to do since the code uses CF9h to
reset.
So its possible that while previously undefined it still ended up
defaulting to 0 and the codepath exercised on my board is simply
buggy or there is a difference between a true "SB800" and the
"A50 Hudson M1" presumably used on my board.
Change-Id: I33f45925e222b86c0a97ece48f1ba97f6f878499
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10549
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Replace the AMD SMBus section with the equivalent SB800 smbus.asl
include or remove already commented-out sections.
Verified by running the cpp preprocessor over the DSDTs and diffing the
results against this patch.
The only change is in src/mainboard/siemens/sitemp_g1p1/dsdt.asl, where
someone added RADD and SADD to the OpRegion, but those are unused, so
removing them is fine.
Change-Id: I074c8a1ed1c9a944d4988752bd0fc42c199c766c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10618
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Auron only has three GPIOs for RAMID, so there is no need for
sixteen SPD file entries. Only include 8 SPD entries.
Change-Id: Icf83719a2a5b9271b29f48cde5c66c4c8ccd07f4
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/12073
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
On Broadwell, this reduces the number of 'remarks' in the IASL build
from 222 to 3.
Fixes these remarks:
Object is not referenced (Name is within method [_CRS])
The ACPI compiler is trying to be helpful in letting us know
that we're not using various fields in the MCRS ResourceTemplate
when we define it inside of the _CRS method. Since we're not
intending to use those objects in the method, it shouldn't be an
issue, but the warning is annoying and can mask real issues.
Moving the creation of the MCRS object to outside of the CRS
method and referencing it from there solves this problem.
This change was made for fsp_baytrail in commit 2eaa0d49
fsp_baytrail: Fix ACPI 'Object is not referenced' warnings
Change-Id: I67a1faf963d1868f4133c7747a43a511cd28a44b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11268
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: Ifb434db1b8eb01acf48f26366c5237ae49a8730a
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11884
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: Ide50b34184b80c86b996f86dd589c3cf3bf75587
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11883
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: I1e69cf0fd73e70ed6656b9ed6f55aba4c56a6edd
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11882
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/southbridge/intel/i82801gx/acpi`. Devices with the
southbridge `intel/i82801ix`, like the laptop Lenovo X200, use the exact
same ASL code though. So share this in the directory
`src/southbridge/intel/common/acpi`.
Change-Id: I33b7993bcdbef7233ed85a683b2858ac72c1d642
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11881
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/cpu/intel/model_6dx/acpi`, although the devices
can also use different Intel CPU models like, for example,
`intel/model_6ex` on the Lenovo T60.
Therefore move the file to the directory `src/cpu/intel/common/acpi` so
that other devices, like Intel GM45 based devices, can also include it.
Change-Id: I90126b66a4d70468923622a8e3aebadeafcbf96f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11880
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Before this fix the value of PcdEnableSdio was printed as the MIPI/ISP
configuration option.
TEST=Built and booted on Minnowboard Max
Change-Id: Ia9b02d520f4e615f90b45935456b9d97c5d00f11
Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl>
Reviewed-on: http://review.coreboot.org/10126
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
connections checked by desoldering the FCH and looking at the PCB
this lowers the power consumption by about 150-200mW measured on primary side
based on change #5397
Change-Id: I986c4cc73a247994f2a47fdfd03f585069ca9385
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/11866
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
don't use non-volatile pointers for MMIO access
Change-Id: I9f38012a806e43f2535265f1d25537c59b53904e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/12081
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ia0313b9ecd64c9e6f99a140772ebb35abe0175fd
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11950
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I3623f8945bd62b7050ec609934f96543552c792b
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12018
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
|
|
Change-Id: I7503ae42eb8bc91411413ef2cc7e7a723df7091a
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11990
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I94b870f47581a4a2591d02eeb37627666e0f4297
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11945
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I6dff74b3857e1fb384aefc87b44e7679bd4aab07
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11948
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ic27d404a7ed76b58043037e8b66097db6d664501
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11942
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Icda915933c4ebf3a735d9e1d4e4dbb1138a06b39
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11955
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
|
|
The reintroduction of cougar_canyon2 crossed beams with the
moving the GMA display brightness data in ACPI into individual
mainboards.
Make things build again by having the board use the same default values
that it used to use automatically. They may be wrong, but no worse than
what was there before.
Change-Id: Id788034c38b42e1c35d9cd17e9bbb2ce49e3e91c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12132
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I0a9b3a66231052622c862bae32b900f52f6efba9
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11944
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
|
|
To help hypervisors to assign PCI devices individually to virtualization
guests, page align dynamically allocated MMIO resources.
Tested with kontron/ktqm77 which has dynamically configured onboard
devices on the root bus and secondary buses. Booted Linux and checked
the configuration with `lspci -v`. Got the configuration through Muen's
tools which are very picky about overlapping and alignment. Booted a
Muen based system that uses many onboard devices. GMA, xHCI and one NIC
(on a secondary bus) were verified to function properly.
Change-Id: I2b7115070e1ccad64565feff025289732c3b5e66
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/12111
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Those are actually board specific. Keep the old value as defaults,
though. The defaults are included by all affected boards.
Change-Id: Ib865c7b4274f2ea3181a89fc52701b740f9bab7d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11705
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
Values based on correlation of brand strings, brand numbers and the TDP
listings on AMD's web site (Wikipedia for Athlon 64 FX-7x TDPs).
Change-Id: I7e6d12d0b6cc4fefc3f84076234c62c40e08304c
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10926
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Please don't remove chipsets and mainboards without discussion and input
from the owners. Someone was asking about cougar canyon 2 just a couple
of weeks ago - there's obviously still interest.
This reverts commit fb50124d22014742b6990a95df87a7a828e891b6.
Change-Id: Icd7dcea21fa4a7808b25bb8727020701aeebffc9
Signed-off-by: Martin Roth <martinroth@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/12128
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
It works there, we want it, disable that restriction.
Change-Id: Idc023775f0750c980c989bff10486550e4ad1374
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/12094
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This reverts commit e6606518243d9beda31693d40493b5f7a1a3e2e0.
After some discussion on IRC we decided to revert it as libpayload can
only read the copy that was removed (and other users like nvramtool can
only read the other copy). So we need both copies at this time.
Signed-off-by: Nico Huber <nico.h@gmx.de>
Change-Id: I6cf6b2a1523d771bb52f3d5720b1b16ed4b348db
Reviewed-on: http://review.coreboot.org/11696
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
We need to special-case filling out the vboot structures when
we use CBFS instead of vboot's custom indexed format, otherwise
(due to the way the CBFS header looks), it will try to write several
million entries.
Change-Id: Ie1289d4a19060bac48089ff70e5cfc04a2de373f
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/11914
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Some registers only allow word-sized or half-word-sized operations and will
cause a data fault when accessed with byte-sized operations.
However, the compiler may or may not break such an operation into smaller
(byte-sized) chunks. Thus, we need to reliably perform word-sized operations for
32 bit read/write and half-word-sized operations for 16 bit read/write.
This is particularly the case on the rk3288 SRAM registers, where the watchdog
tombstone is stored. Moving to GCC 5.2.0 introduced a change of strategy in the
compiler, where a 32 bit read would be broken into byte-sized chunks, which
caused a data fault when accessing the watchdog tombstone register.
The definitions for byte-sized memory operations are also adapted to stay
consistent with the rest.
Change-Id: I1fb3fc139e0a813acf9d70f14386a9603c9f9ede
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: http://review.coreboot.org/11698
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
With the introduction of these options in commit b26156e
(bd82x6x/xhci: Set mask of ports switchable between USB2 and USB3.)
the default regressed to disable these capabilities. Maybe other boards
regressed too. I didn't check.
Change-Id: I220896e656d00145618e61d55b74904517c7d855
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11287
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Merge artifact -- don't check spd_index twice.
BUG=None
TEST=Build only
BRANCH=Auron
Original-Change-Id: I0cc372fec415646854aa931949ed0f57b473cb01
Original-Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/234421
Original-Reviewed-by: Bernie Thompson <bhthompson@chromium.org>
(cherry picked from commit 850125141b52886c845161434a1320676e59534d)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I0070e3f26ebddba716905ebb934bcec4715c4b05
Reviewed-on: http://review.coreboot.org/11912
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
|
|
These are needed for the hardware-sequencing function of the PCH SPI
interface. Values are specific to the flash chip used on a board.
Change-Id: Id06766b4bac2686406bc09b8afa02f311f40dee7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11798
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-by: Duncan Laurie <dlaurie@google.com>
|
|
Part of the following patch was lost in the merge from chromium.
This patch fixes up the spd_index for the copy from the SPD file.
In spd.c "spd_index *= SPD_LEN" will change the original spd_index
from gpio and let the following if(spd_index>3) to misjudge and
disable channel 1 incorrectly. So we calculate the index for spd file
memcpy when calling memcpy().
BUG=chrome-os-partner:32879
TEST=Can get total memory 4G on yuna 4G SKU
BRANCH=Auron
Original-Change-Id: Iebc49e20e4ca15ef6db8c4defe43cc22382a28bf
Original-Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/234420
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Original-Commit-Queue: Shawn N <shawnn@chromium.org>
Original-Tested-by: Shawn N <shawnn@chromium.org>
(cherry picked from commit 3b1fce58b7b4b15e947b40fd011174d4e8e294bc)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I03f9d63623e083c99d349d938fd802d828858f70
Reviewed-on: http://review.coreboot.org/11911
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Georg Wicherski <gw@oxff.net>
Tested-by: build bot (Jenkins)
|
|
Do not hardcode the CPU downstream non-posted request limit; the
value of this register is CPU family specific and is set appropriately
in the corresponding CPU driver code.
Change-Id: I432b942f114243cba23c9a8d916cf6d07bc4740b
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11935
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I975142351c0c033f9dc44670dcf819d296896921
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11934
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I6a32b69d3b75d7d086dc7f8ea1e195473399f406
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11933
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Commit dbeedbef (arch/x86/bootblock: Link in object files selected with
bootblock-y) breaks building of x86 boards with
`CONFIG_EARLY_CBMEM_INIT` *not* selected but CBMEM time stamp collection
enabled.
Aaron Durbin explained as below [1] and provided this patch to fix it.
> That change actually processes bootblock-objs where before it never did
> such a thing. I'm sure this isn’t the only issue lurking. bootblock on
> x86 implied romcc and thus all the bootblock-y += rules that other
> architectures use worked, but now all the implied assumptions are no
> longer true on x86.
>
> timestamp stuff on x86 !CONFIG_EARLY_CBMEM_INIT is the issue you're
> seeing. In order to compile timestamp.c for bootblock under these
> conditions will mean there needs to be some more Makefile guarding.
[1] http://review.coreboot.org/11864
Change-Id: I3441b9fcdbbc8bbe82b9f2075e60668a846ecf09
Fix-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11875
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I208b012c6b612a94b3bbc8235d5a005028be8bcc
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11832
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I626a11c17c9d05c174c507d50684e498c8604cbc
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11905
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The broadwell soc code was upstreamed based off an old coreboot branch
and apparently never tested with USBDEBUG.
This changeset fixes USBDEBUG on the not yet upstreamed Auron-Paine
board, as verified with a FT232H setup. The fix is simply removing
outdated code that since branching off had been deduplicated in upstream
coreboot, anyway.
Change-Id: I53c924aa2a5357ed8313d0c9eaa2f9f9e132345e
Signed-off-by: Georg Wicherski <gwicherski@gmail.com>
Reviewed-on: http://review.coreboot.org/11874
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Serial number is derived from the MAC address of first NIC.
Change-Id: I91e5555b462cca87d48fb56c83aedd1eb02eba62
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/11901
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
Do this to wipe error message and hexdump of SPD from console log.
Change-Id: I45ffcb1c80aecf43b79d93faedcd62c8f0023cb7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/11900
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Value of tRFCmin was incorrectly using 2 Gigabit chip data.
There was no observed instability or bug reports because of this.
Change-Id: Ifa03b883afa5a304dd20caf3d4d0383c6cfebdb8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/11899
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I3a42ba9494b5174920e36e3110b8d62d721fe742
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11886
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ia158b4c6c12fb6e22ea7fed9035574a3abedf98c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11885
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
We use UNDERSCORE_CASE. For the MTRR macros that refer to an MSR,
we also remove the _MSR suffix, as they are, by definition, MSRs.
Change-Id: Id4483a75d62cf1b478a9105ee98a8f55140ce0ef
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11761
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This chip is still being used and should not have been deleted. It's
a current intel chip, and doesn't even require an ME binary.
This reverts commit 959478a763c16688d43752adbae2c76e7764da45.
Change-Id: I78594871f87af6e882a245077b59727e15f8021a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11860
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The existing microcode update system used custom, manually generated microcode
blob files. This made updates very difficult. Update parser to use stock
microcode update files as provided by AMD.
Change-Id: I772b264ad167f2a5d629dab5d64d9b0ccab3a053
Signed-off-by: Audrey Pearson <apearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11829
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Updating to a new IASL introduces a lot of warnings that are
not serious issues but can be fixed with some reworks.
- Method local variables that are set but never used now warn,
when needing to read back a register the ordering is now changed
to set the value in Local0 first so the compiler does not complain.
- Methods that create an object must be serialized
- A ResourceTemplate declared inside a _CRS with a named variable
does not seem to be able to compile without a warning. To fix
this move the ResourceTemplate outside the _CRS method.
- The DPTF CPU code was still using the old legacy \_PR.CPUx
instead of the new \_PR.CPxx definitions.
BUG=chrome-os-partner:44622
BRANCH=none
TEST=build glados with iasl-20150717 and see no warnings
Original-Change-Id: I4a66c7eb6495aac4ae1aa42100c846725c1a04d2
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/302168
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ia3af802ca2faab4f1c59e73f2ce31a65c7e862e0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11812
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@google.com>
|
|
In order to support verstage the cache-as-ram split
is taken advantage of such that verstage has the
cache-as-ram setup and rosmtage has the cache-as-ram
tear down path. The verstage proper just initializes
the console and attempts to run romstage which triggers
the vboot verification of the firmware. In order to
pass the current FSP to use during romstage a global
variable in cache-as-ram is populated before returning
to the assembly code which tears down cache-as-ram.
BUG=chrome-os-partner:44827
BRANCH=None
TEST=Built and booted glados with verstage support as well as
VBOOT_DYNAMIC_WORK_BUFFER with direct link in romstage.
Change-Id: I8de74a41387ac914b03c9da67fd80f8b91e9e7ca
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11824
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
