| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: Idd4127f7491524121b4b65c6fb9511e2c8159912
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/18609
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
cr50 by default delays nvmem commits internally from the point of
reset to accumulate change state. However, the factory process can
put a board into dev mode through the recovery screen. This state
is stored in the TPM's nvmem space. When the factory process is
complete a disable_dev_request and battery_cutoff_request is performed.
This leads to disabling the dev mode in TPM, but the battery is
subsequently cut off so the nvmem contents never stick. Therefore,
whenever antirollback_write_space_firmware() is called we know there
was a change in secdata so request cr50 to immediately enable nvmem
commits going forward. This allows state changes to happen immediately.
The fallout from this is that when secdata is changed that current
boot will take longer because every transaction that writes to TPM
nvmem space will perform a write synchronously. All subsequent boots
do not have that effect.
It should also be noted that this approach to the implementation is
a pretty severe layering violation. However, the current TPM APIs
don't lend themselves well to extending commands or re-using code
outside of the current routines which inherently assume all knowledge
of every command (in conflict with vendor commands since those are
vendor-specific by definition).
BUG=b:35775104
BRANCH=reef
TEST=Confirmed disablement of dev mode sticks in the presence of:
crossystem disable_dev_request=1; crossystem
battery_cutoff_request=1; reboot;
Change-Id: I3395db9cbdfea45da1f5cb994c6570978593b944
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18681
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Going forward it's important to note when a CR50 is expected
to be present in the system. Additionally, this Kconfig addition
provides symmetry with the equivalent i2c Kconfig option.
BUG=b:35775104
Change-Id: Ifbd42b8a22f407534b23459713558c77cde6935d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18680
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
verstage can be pretty chatty so bump the pre cbmem console size
when building for Chrome OS so that all messages can be observed.
BUG=b:35775104
BRANCH=reef
TEST=Booted and noted no cutoff of console when sec data being saved.
Change-Id: I0ce2976572dedf976f051c74a3014d282c3c5f4c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18679
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
marshal_blob() was setting an unsigned size (size_t) to a value
of -1 when an error is determined. This is wrong for the current
implementation of the code because the code assumes the buffer
space gets set to 0. Setting an unsigned value to -1 effectively
tells the library the buffer has unlimited amount of space.
BUG=b:35775104
Change-Id: I677a1fd7528bef3ea7420d0a8d0a290e9b15cea3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18678
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
SRCCLKREQ4 is unused, so configure SRCCLKREQ4 as NC (No Connect).
Change-Id: I6e265b9c9faa0df20208bb82278cadbbbbe6c537
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/18589
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add the missing EC event codes in elog.h and correct the event code value for
RECOVERY_HWREINIT.
Change-Id: If9fb319cce1e4acce4b3d7c3a39365986856a9b4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18693
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fix the following error detected by checkpatch.pl:
ERROR: space required before the open parenthesis '('
TEST=Build and run on Galileo Gen2
Change-Id: I8953fecbe75136ff989c9e3cf6c5e155dcee3c3b
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18698
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Fix the following warning detected by checkpatch.pl:
WARNING: braces {} are not necessary for single statement blocks
TEST=Build and run on Galileo Gen2
Change-Id: Ie4b41f6fb75142ddd75103a55e0347ed85e7e873
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18697
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins)
|
|
Fix the following errors detected by checkpatch.pl:
ERROR: "foo* bar" should be "foo *bar"
ERROR: "(foo*)" should be "(foo *)"
ERROR: "foo * const * bar" should be "foo * const *bar"
TEST=Build and run on Galileo Gen2
Change-Id: I0d20ca360d8829f7d7670bacf0da4a0300bfb0c1
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18696
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Fix the following warning detected by checkpatch.pl:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
The remaining 37 warnings in gcov-io.c and libgcov.c are all false
positives generated by checkpatch detecting a symbol or function name
ending in _unsigned.
TEST=Build and run on Galileo Gen2
Change-Id: I9f1b71993caca8b3eb3f643525534a937d365ab3
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18695
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
1. Update DPTF TSR1 passive trigger points.
TSR1 passive point: 50
2. Update DPTF PL1 Minimum
PL1 min: 2.5W
BUG=b:35586881
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: Ia2634f40098d026c4d228fab4b7c05501c1ff05f
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18699
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fix the following error detected by checkpatch.pl:
ERROR: space prohibited after that '&' (ctx:ExW)
TEST=Build and run on Galileo Gen2
Change-Id: Ied8b4c00fc57a35ed4d649264a5ff1b8dcc6a1cd
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18648
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix the following error detected by checkpatch.pl:
ERROR: space required after that ',' (ctx:VxV)
TEST=Build and run on Galileo Gen2
Change-Id: I297bfc3d03dc95b471d3bb4b13803e81963841b5
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18647
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix the following error and warning detected by checkpatch.pl:
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
TEST=Build and run on Galileo Gen2
Change-Id: I487771b8f4d7e104457116b772cd32df5cd721a6
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18646
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix the following error detected by checkpatch.py:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
False positives are generated when assembly code is used in a macro. An
example is:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
+#define post_code(value) \
+ movb $value, %al; \
+ outb %al, $CONFIG_POST_IO_PORT
False positives are also generated for linker script include files. An
example is:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
+#define SET_COUNTER(name, addr) \
+ _ = ASSERT(. <= addr, STR(name overlaps the previous region!));
\
+ . = addr;
False positives are also generated for attribute macros. An example is:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
+#define DISABLE_TRACE_ON_FUNCTION __attribute__
((no_instrument_function));
TEST=Build and run on Galileo Gen2
Change-Id: I88abf96579e906f6962d558a3d09907f07d00b1c
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18644
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix the following error detected by checkpatch.pl:
ERROR: trailing statements should be on next line
TEST=Build and run on Galileo Gen2
Change-Id: I169f520db6f62dfea50d2bb8fb69a8e8257f86c7
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18643
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix warning detected by checkpatch.pl:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
BRANCH=none
BUG=None
TEST=Build and run on Galileo Gen2
Change-Id: I23d9b4b715aa74acc387db8fb8d3c73bd5cabfaa
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18607
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add two GPIO macros:
1. PAD_CFG_GPI_APIC_EDGE allows a pin to be route to the
APIC with input assuming the events are edge triggered.
2. PAD_CFG_GPI_ACPI_SCI_LEVEL to route the general purpose
input to SCI assuming the events are level triggered.
Change-Id: I944a9abac66b7780b2336148ae8c7fa3a8410f3f
Signed-off-by: Rahul Kumar Gupta <rahul.kumarxx.gupta@intel.com>
Reviewed-on: https://review.coreboot.org/18533
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add SKL/KBL PCH-H GPIO settings referring from SKL PCH-H
specifications to support sklrvp11.
Split the gpio_defs.h into headers gpio_pch_h_defs.h and
gpio_soc_defs.h for PCH-H specific and SOC specific GPIO
defs respectively.
Change-Id: I5eaf8d809a1244a56038cbfc29502910eb90f9f2
Signed-off-by: Li Cheng Sooi <li.cheng.sooi@intel.com>
Signed-off-by: Rahul Kumar Gupta <rahul.kumarxx.gupta@intel.com>
Reviewed-on: https://review.coreboot.org/18027
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In all simplicity, with board/OptionsIds.h file having:
IDSOPT_IDS_ENABLED TRUE
IDSOPT_TRACING_ENABLED TRUE
And src/Kconfig modified to:
config WARNINGS_ARE_ERRORS
default n
With these settings AGESA outputs complete debugging log
where-ever you have your coreboot console configured.
Change-Id: Ie5c0de6358b294160f9bf0a202161722f88059c1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15320
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins)
|
|
We build with WARNINGS_ARE_ERRORS, while IDS tracing will
raise various (non-fatal) printk() format warnings.
Change-Id: I9dc81c89ee60d17a6556a412380fed1413af66bd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18560
Tested-by: build bot (Jenkins)
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
We have been forced to build AGESA with ASSERT() as non-fatal
for some board, as hitting those errors is not uncommon.
For the cases touched here, abort eventlog operations early
to avoid further errors and dereference of null pointers.
Change-Id: I1a09ad55d998502ad19273cfcd8d6588d85d5e0c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18543
Tested-by: build bot (Jenkins)
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Do not evaluate AmdEventParams if AmdReadEventLog() fails.
Change-Id: I2b8afe827ffe6757e64c00ab005d3bb8cc577321
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18611
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Implement threshold as described in AMD.h, and do not add
entries below STATUS_LOG_LEVEL in the eventlog.
Change-Id: Ic9e45b1473b4fee46a1ad52d439e8682d961dc03
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18542
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This is useful for debugging S3 issues and in general
to understand AGESA memory allocator behaviour.
Change-Id: I422f2620ed0023f3920b8d2949ee1c33a6c227e0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18535
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
|
|
A problem around CAR teardown time may result with missing
training results at the time we want to save them.
Record this in the logs for debugging purposes, it will
not be possible to use S3 suspend if this happens.
Change-Id: Id2ba8facbd5d90fe3ed9c6900628309c226c2454
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18534
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
When allowing use of SSE instructions, stack must be
aligned to 16 bytes. Adjust x86 entry to C accordingly,
by pushing values to maintain the alignment.
Fixes regression with new toolchain using GCC-6.3 and
ec0a393 console: Enable printk for ENV_LIBAGESA
For some builds, the above-mentioned commit emitted
SSE instruction 'andps (%esp),%xmm0' with incorrectly
aligned esp, raising exception and thus preventing boot.
Change-Id: Ief57a2ea053c7497d50903838310b7f7800bff26
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18622
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The init files for the Core Duo and Core 2 Duo are very similar. Reduce
the differences, by using the same order for the include statements, the
same blank lines, and the same comments.
Change-Id: I0de060222a61a482377c760c6031d73c7e318edf
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/18506
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This is required to transmit button information from EC to kernel.
BUG=b:35774934
BRANCH=None
TEST=Verified using evtest that kernel is able to get button
press/release information from EC.
Change-Id: I8f380f935c2945de9d8e72eafc877562987d02db
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18642
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This is required to pass button information from EC to kernel without
using 8042 keyboard driver.
1. Define EC buttons device using GOOG0007 ACPI ID.
2. Guard enabling of this device using EC_ENABLE_MKBP_DEVICE.
BUG=b:35774934
BRANCH=None
TEST=Verified using evtest that kernel is able to get button
press/release information from EC.
Change-Id: I4578f16648305350d36fb50f2a5d2285514daed4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18641
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Apollolake platform comes with FPF (field-programmable-fuses). FPF can
be blown only once, typically at the end of the manufacturing process.
This patch adds code that sends a request to CSE to figure out if FPFs
have already been blown.
Change-Id: I9e768a8b95a3cb48adf66e1f17803c720908802d
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18604
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: If866453f06220e0edcaa77af5f54b397ead3ac14
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18603
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Add common driver that can send/receive HECI messages. This driver is
inspired by Linux kernel mei driver and somewhat based on Skylake's.
Currently it has been only tested on Apollolake.
BUG=b:35586975
BRANCH=reef
TEST=tested on Apollolake to send single messages and receive both
fragmented and non-fragmented versions.
Change-Id: Ie3772700270f4f333292b80d59f79555851780f7
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18547
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ib284493d886b223e8c85607de5fdb56b698fe5fa
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18546
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fix the following errors detected by checkpatch.pl:
ERROR: space prohibited after that open parenthesis '('
ERROR: space prohibited before that close parenthesis ')'
TEST=Build and run on Galileo Gen2
Change-Id: I586c5731c080282080fe5ddf3ac82252cb35bdd4
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18636
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Allow EC mode change event to wake AP up in S3.
BUG=b:35775085
BRANCH=None
TEST=Compiles successfully for poppy.
Change-Id: I6f1546c60aef6620e22cdce2fab3a2709e6556a1
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18608
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The event log entry indicating developer mode is useful for the
boot path, but is not really useful on the resume path and removing
it makes the event log easier to read when developer mode is enabled.
To make this work I have to use #ifdef around the ACPI code since
this is shared with ARM which does not have acpi.h.
BUG=b:36042662
BRANCH=none
TEST=perform suspend/resume on Eve and check that the event log
does not have an entry for Chrome OS Developer Mode.
Change-Id: I1a9d775d18e794b41c3d701e5211c238a888501a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18665
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
If Deep Sx is enabled the event log will get entries added on every
power sequence transition indicating that the suspend well has failed.
When a board is using Deep Sx by design this is intended behavior and
just fills the logs with extraneous events.
To make this work the device init state has to be executed first so it
actually enables the Deep Sx policies in the SOC since this code does
not have any hooks back into the devicetree to read the intended setting
from there.
BUG=b:36042662
BRANCH=none
TEST=Perform suspend/resume on Eve device with Deep S3 enabled, and
then check the event log to be sure that it does not contain the
"SUS Power Fail" event.
Change-Id: I3c8242baa63685232025e1dfef5595ec0ec6d14a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18664
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add a function to read the current state of Deep S5 configuration
and indicate if it is enabled (for AC and/or DC) or disabled.
This is similar to the existing function that checks Deep S3
enable state.
BUG=b:36042662
BRANCH=none
TEST=tested with subsequent commits to check Deep S5 state at boot
and filter event log messages if it is enabled.
Change-Id: I4b60fb99a99952cb3ca6be29f257bb5894ff5a52
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18663
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add options to the skylake chip config that will allow tuning the
various settings that can affect acoustics with the CPU and its VRs.
These settings are applied inside FSP, and they can adjust the slew
slew rate when changing voltages or disable fast C-state ramping on
the various CPU VR rails.
BUG=b:35581264
BRANCH=none
TEST=these are currently unused, but I verified that enabling the
options can affect the acoustics of a system at runtime.
Change-Id: I6a8ec0b8d3bd38b330cb4836bfa5bbbfc87dc3fb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18662
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
A new board revision is making use of two previously unused GPIOs
to drive BOOT/RESET pins to an on-board MCU.
The reset pin is open drain so it is set as input by default, and
the boot pin is driven low by default.
Since these are UART0 pins they also need to be set up again after
executing FSP-S as it will change them back to native mode pins.
BUG=b:36025702
BRANCH=none
TEST=manual testing on reworked board, toggling GPIOs to put
the MCU into programming mode.
Change-Id: Id6f0ef2f863bc1e873b58e344446038786b59d25
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18661
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ic5c92d9a2d8bb040a04602e5da2cd37a2ae8db95
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/18052
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fine tune USB2, need to override the following registers.
port#1:
PERPORTPETXISET=7
PERPORTTXISET=0
BUG=b:35858164
BRANCH=reef
TEST=built, measured eye diagram on snappy, and reviewed by intel
Change-Id: I461cf8f032b4e70abc9707e6cd3603a62cee448f
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18590
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
No board with binaryPI currently supports HAVE_ACPI_RESUME. For
platforms with PSP the approach is also very different from what
we previously had here.
Furthermore, s3_resume.[ch] files under cpu/amd/pi do not
distinguish between NonVolatile and Volatile buffers of S3 storage.
This means the Volatile buffer that is maintained and available in
CBMEM is unnecessarily copied to SPI flash. This has been fixed on
open-source AGESA directory, so development of S3 suspend support
with binaryPI is better continued with that.
Unfortunately there are further complications and indications that
open-source AGESA may have always had a low-memory corruption
issue. This has to be investigated separately before restoring
or claiming S3 is supported on binaryPI.
Change-Id: I81585fff7aae7bcdd55e5e95bc373e0adef43ef0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18501
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
None of the boards currently have HAVE_ACPI_RESUME and
and ACPI S3 support calls should not appear under board
directories anyways.
Change-Id: I1abd40ddba64be25b823abf801988863950c1eb5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18500
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
The file is used for fam15.
Change-Id: I7cdf238a8f7be4bf79546bcfc3c9d05bd8986e3e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18635
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Definitions are not part of ACPI S3 feature, nor do
they require any AGESA headers so move them to a
better location.
Change-Id: I9269e9d65463463d9b8280936cf90ef76711ed4f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18616
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Declaration of main in cpu/amd/car.h conflicts with the
definition of main required for x86/postcar.c in main_decl.h.
Change-Id: I19507b89a1e2ecf88ca574c560d4a9e9a3756f37
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18615
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Note that M and M_PRO had same DefaultPlatformMemoryConfiguration
defined, use one for both.
Change-Id: Ia1925957800a7fe6ef511b2d041f7a863c8fc931
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18606
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Relocate the enabling of the LAPIC out of the southbridge source and
surround it with a check for CONFIG_UDELAY_LAPIC (typical for AMD
systems). The LAPIC is now enabled for all cores; not only the BSP,
and not only when the UART is used.
This solves the problem of APs not having their APICs enabled when
the timer is expected to be functional, e.g. verstage often uses
do_printk_va_list() instead of do_printk() which exits early for
APs when CONFIG_SQUELCH_EARLY_SMP=y.
The changes were tested with two Gardenia builds, one using verstage
and another with CONFIG_SQUELCH_EARLY_SMP=n.
Original-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit 93ffc311165f19d4192a5489051fa4264cd8e0ad)
Change-Id: Ieaecc0bf921ee0d2691a8082f2431ea4d0c33749
Signed-off-by: Marc Jones <marcj303@gmail.com>
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18436
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Only declare S3 support in ACPI if CONFIG_HAVE_ACPI_RESUME
is set.
Change-Id: I6f8f62a92478f3db5de6feaa9822baad3f8e147e
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18493
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add some generic functions that can configure the SPI interface to
have faster performance.
Given that the hudson files are used across many generations of FCHs,
make sure to refer to the appropriate BKDG or RRG before using the
functions. Notable differences:
* Hudson 1 defines read mode in CNTRL0 differently than later gens
* Hudson 1 supports setting NormSpeed in Cntr1 but Hudson3 allows
setting FastSpeed as well
* Kabini, Mullins, Carrizo and Stoney Ridge contain a "new" SPI100
controller
Original-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit 1922d6f424dcf1f42e2f21fb7c6d53d7bcc247d0)
Change-Id: Id12440e67bc575dbe4b980ef1da931d7bfae188d
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18442
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add defines that will be used later for setting the fastest settings
in the SPI controller.
Original-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit 0d2c28b8156dcc1f3dc925b3c3ba15b6b07f202c)
Change-Id: I660cc9ed6910c33042321c80453c7f74912455d9
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18441
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Remove unused definitions from a .c file and use the BIT(n) macro
found in types.h instead. Convert existing definitions to BIT(n).
Orignial-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit f403d12b49985ee9d9b339a6659b60ef1560519c)
Change-Id: I24105bf75263236dbdbc2666f03033069d1d36d2
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18440
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Fix the error detected by checkpatch and update the copyright date.
TEST=Build and run on Galileo Gen2
Change-Id: Idc55169913e7b7b0aca684c26f6ed3b349fc6c09
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18592
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix the errors detected by checkpatch and update the copyright dates.
TEST=Build and run on Galileo Gen2
Change-Id: Idad062eaeca20519394c2cd24d803c546d8e0ae0
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18591
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Gru/Kevin use 933 MHz (actually 928 MHz for better jitter) as max sdram
frequency, while bob uses 800 MHz.
It's normal some variants can't meet 928 MHz SI requirement and hence
have to use a lower freq as spec.
BUG=chrome-os-partner:61001
BRANCH=gru
TEST=check dpll is 800 MHz on bob
Change-Id: I6d19a351f25d1f48547715ce57c3a87d9505f6f1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8176bfea52422c713f144ffec419752aeca66db2
Original-Change-Id: I46afba8d091f1489feeb20cafc44decaa81601fc
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/420208
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Tested-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-(cherry picked from commit eba5dff79eeedae5ff608d2d8d297ccf9c13cb55)
Original-Reviewed-on: https://chromium-review.googlesource.com/448277
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/18581
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The K4B4G1646E-BYK0 shares sdram config with K4B4G1646D-BYK0.
For clarity, sdram-ddr3-samsung-2GB now is used by
- K4B4G1646D-BYK0
- K4B4G1646E-BYK0
- K4B4G1646Q-HYK0
BUG=chrome-os-partner:62131
BRANCH=veyron
TEST=emerge
Change-Id: Ie43f23bf8f5f5b1acbb74c85cac17fe181c841c4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 46d62d87101e0ee1050b00db02b3ecaa4587e9f4
Original-Change-Id: I461c6f36c28ea0eeaf7d64292c9c87ab0c9de443
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/446197
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-(cherry picked from commit f98251a4a4fe4d49721a936a684f6ac80f3f6405)
Original-Reviewed-on: https://chromium-review.googlesource.com/446300
Reviewed-on: https://review.coreboot.org/18519
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This adds SDRAM entries for the following modules:
- Micron: DDMT52L256M64D2PP-107
- Hynix: H9CCNNNBKTALBR-NUD
They are compatible with Samsung K4E8E324EB-EGCF, so this just
copies sdram-lpddr3-samsung-2GB-24EB.inc and changes the name used
in the comment near the top.
Notes on our "special snowflake" boards:
- veyron_danger's RAM ID is hard-coded to zero, so I skipped changes
involving the binary first numbering scheme.
- Rialto's SDRAM mapping is different, so I padded its SDRAM entries
to 24 to match other boards.
- veyron_mickey requires different MR3 and ODT settings than other
boards due to its unique PCB (chrome-os-partner:43626).
BUG=chrome-os-partner:59997
BRANCH=none
TEST=Booted new modules on Mickey (see BUG)
Change-Id: If2e22c83f4a08743f12bbc49b3fabcbf1d7d07dd
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 35cac483e86e57899dbb0898dad3510f4c2ab2d3
Original-Change-Id: I22386a25b965a4b96194d053b97e3269dbdea8c7
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/412328
Original-Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Queue: Jiazi Yang <Tomato_Yang@asus.com>
Original-Tested-by: Jiazi Yang <Tomato_Yang@asus.com>
Original-(cherry picked from commit bd5aa1a5488b99f2edc3e79951064a1f824062f6)
Original-Reviewed-on: https://chromium-review.googlesource.com/446299
Original-Commit-Ready: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18518
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix the following issues:
* A raw read is described by a single read segment, don't assert.
* Support reads longer than the FIFO size.
* Support writes longer than the FIFO size.
* Use the 400 KHz clock by default.
* Remove the error displays since vboot device polling generates
errors.
TEST=Build and run on Galileo Gen2
Change-Id: I421ebb23989aa283b5182dcae4f8099c9ec16eee
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18029
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Configure the right GPIOs for finger print sensor interrupt and reset
lines.
As per the schematics GPP_C8 is for sensor interrupt and GPP_C9
is for sensor reset.
Change-Id: Ib25c68ec2fe20b1302b6170d67ceab7e8cca1a83
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18389
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
One very long line has to be wrapped to be shorter than 80 characters to
satisfy the lint scripts.
Note, that this gets rid of the brackets ().
Change-Id: Ie98eff360ebc5b68ce496edc15eb2d9fddcac868
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/18556
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Status:
- The primary PCIe 16x slot works:
It was tested with a GPU compatible with nouveau
- USB and audio are not very reliable
- The ethernet card is not seen with lspci
- The secondary pcie16x slot isn't working:
When plugging a GPU inside, it's not seen with lspci
- SATA works: The board fully boots GNU/Linux
- Serial doesn't work
- Populating the RAM slots might have to follow
the recommended memory configuration that is described
in the mainboard manual in order to be able to boot.
Note that when running the shutdown command, the default
boot firmware will rewrite part of the boot flash before
powering off the machine.
Flashing coreboot internally from the default boot fimrware can
still work, if the power plug is removed after running flashrom.
Change-Id: I934de521d0acceb7770f23b2ae15c31a67ae73eb
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: https://review.coreboot.org/16931
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
These definitions do not require AGESA.h include,
and we will eventually remove agesawrapper.h files.
Change-Id: I1b5b78409828aaf2616e177bb54a054960c3869f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18588
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The size of the array did not match that of the actual
allocation. Furthermore, the tables are written as
part of set_pci_irqs() in hudson/pci.c.
Also the removed code was never reached runtime, as it is
only executed on ACPI S3 resume path that is currently
disabled.
Change-Id: If1c47d53a7656bdff40d93fc132c8c057184ae46
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18587
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I7a1574259f73a52b66d03c686ae8ab70345c36ed
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18586
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This file is only static defines.
Change-Id: Id50a0eba1ce240df36da9bd6b2f39a263fa613df
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18585
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Change-Id: Ib37989ee7535e59b1903537995f8383d8b04387c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18584
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Messages from AGESA proper are additionally controlled
by various IDS parameters in board/OptionsIds.h file.
Change-Id: I83e975d37ad2bdecb09c483ecae71c0ed6877731
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18545
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Definition is required to enable use of printk() from AGESA proper.
Change-Id: I6666a003c91794490f670802d496321ffb965cd3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18544
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The current elog implementation has two event types defined for 0xa7,
apparently the result of divergent coreboot trees on chromium where
some events were added to ARM systems but not upstreamed until later.
Fix this by moving ELOG_TYPE_THERM_TRIP to be 0xab, since the current
elog parsing code in chromium is using ELOG_TYPE_SLEEP for 0xa7.
BUG=b:35977516
TEST=check for proper "CPU Thermal Trip" event when investigating a
device that is unexpectedly powering down.
Change-Id: Idfa9b2322527803097f4f19f7930ccbdf2eccf35
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18579
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use header (soc/intel/common/block/include/intelblocks/msr.h) for
MSR macros
Change-Id: I401b92cda54b6140f2fe23a6447dad89879a5ef0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18554
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I7bd83d293fcc1848f6f64526d8f38d010c1f69a3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18223
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Move all common MSRs as per IA SDM into a common location
to avoid duplication.
Change-Id: I06d609e722f4285c39ae4fd4ca6e1c562dd6f901
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18509
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Create sample model for common Intel XHCI driver.
Change-Id: I81f57bc713900c96d998bae924fc4d38a9024fe3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18221
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Select all Kconfig belongs into Intel SoC Family block/ips common
code model and include required header.h file.
Change-Id: Idbce59a57533dbeb9ccfadca966c3d7560537fa0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18377
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Don't need "skylake/include/soc/xhci.h", hence removed.
Change-Id: I35df2003f311b557b622ce1d7a1c2e832693c2fc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18508
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Split out dual-port switching functionality into dedicated xdci.c.
Change-Id: Ia58fc3fb6d017dd0c19cc450d1caba307fc89a7b
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18226
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Currently, when using `iasl` 20140926-32 [Oct 1 2014] from Debian 8
(Jessie/stable), the build of the Lenovo X60 fails due to syntax errors.
ASL 2.0 supports `<<`. For consistency, right now, coreboot still uses
the old syntax. So use `ShiftLeft` instead, which also fixes the build
issue with older ASL compilers.
Change-Id: Id7e309c31612387da3920cf7d846b358ac2bdc71
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/18520
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Support for voltage margining is dependent on the platform.
Enabling voltage margining puts additional constraints for
the SLP_S0# to be asserted and hence moving to S0ix state.
If the platform PMIC/VR supports PCH voltage reduction,
voltage marigining can be enabled.
Use the UPD provided by FSP to enable/disable voltage margining.
Change-Id: Iea214e9d7d6126e8367426485c6446ced63caa66
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18469
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This is selected by default and not overwritten anywhere else for this
board.
Change-Id: I0f803e130366ee322163f7bb6fa16cac75f5416e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18541
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
BUG=chrome-os-partner:62963
BRANCH=None
TEST=Compiles successfully
Change-Id: Icb929262fd67362b8e5c5cf31dce04ab1f496695
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18467
Tested-by: build bot (Jenkins)
Reviewed-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
As we drive both channels with the same speed,
chan0dll and chan1dll are the same.
Change-Id: I7253ea9ea66396c536c82d63c67fecb041681707
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/18472
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins)
|
|
AGESA AmdInitEarly() reconfigures the lapic timer in a way that
conflicts with lapic/apic_timer.
This results in an endless loop when printk() is called after
AmdInitEarly() and before the apic_timer is initialized.
This patch forces a reconfiguration of the timer after
AmdInitEarly() is called.
Codepath of the endless loop:
printk()->
(...)->
uart_tx_byte->
uart8250_mem_tx_byte->
udelay()->
start = lapic_read(LAPIC_TMCCT);
do {
value = lapic_read(LAPIC_TMCCT);
} while ((start - value) < ticks);
[lapic_read returns the same value after AmdInitEarly()]
Change-Id: I1a08789c89401b2bf6d11846ad7c376bfc68801b
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-on: https://review.coreboot.org/17924
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This reverts commit fec8872c9dee4411ba1a89fc8ec833a700b476c6.
The commit introduced a regression which is causing MC4 failures
when 8 RDIMMs are populated in a configuration with a single CPU
package. Using just 4 RDIMMs, the failure does not occur.
After reverting the commit, I tested configurations with
1 CPU (8x8=64GB) and 2 CPU packages (16x8=128GB) using an
Opteron 6276. The MC4 failures did not occur anymore.
Change-Id: Ic6c9de84c38f772919597950ba540a3b5de68a65
Signed-off-by: Daniel Kulesz <daniel.ina1@googlemail.com>
Reviewed-on: https://review.coreboot.org/18369
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
|
|
The newly assigned ACPI ID for coreboot is 'BOOT'
http://www.uefi.org/acpi_id_list
Use this new range of ACPI IDs of "BOOTxxxx" for coreboot specific
ACPI objects instead of the placeholder range of "GOOGCBxx".
Change-Id: I10b30b5a35be055c220c85b14a06b88939739a31
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18521
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fix a typo that was introduce in commit 696ebc2d (Broadwell/Sata:
Add support for setting IOBP registers for Ports 2 and 3.) [1].
Setting one of the SATA port 3 IOBP setting was using the value from
the port 2 register.
On the purism/librem13 (on which SATA port 3 is tested), this change
doesn't seem to affect anything, as that typo wasn't exhibiting any
visible problems anyways.
[1] https://review.coreboot.org/18408
Change-Id: I3948def5c0588791009c4b24cbc061552d9d1d48
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18514
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Follow commit 7676730 (mb/lenovo/x60: Remove PCI reset code from
romstage). The PCI reset was copied from code specific for Roda
RK886EX and Kontron 986LCD-M. It is not needed on the MacBook.
Change-Id: I22dac962e8079732591f9bc134c1433f5c29ff4e
Signed-off-by: Axel Holewa <mono-for-coreboot@donderklumpen.de>
Reviewed-on: https://review.coreboot.org/18502
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I304467353bb9989f0d7e0ad7d1b632081f66b1af
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/18482
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
struct dimm_info has all the parameter types defined in stdint.h
file. So including it.
BUG=none
BRANCH=none
TEST=Build and boot KBLRVP
Change-Id: I707523749ecf415e993b460f9613eae7be859c34
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18471
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Save SMBIOS memory information from FSP MEM_INFO_DATA_HOB in CBMEM.
Add function dimm_info_fill() which populates SMBIOS memory
information from FSP MEM_INFO_DATA_HOB data.
BUG=chrome-os-partner:61729
BRANCH=none
TEST=Build and boot KBLRVP to verify the type 17 DIMM info coming in
SMBIOS table from Kernel command "dmidecode".
Change-Id: I0fd7c9887076d3fdd320fcbdcc873cb1965b950c
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18418
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the MemInfoHob.h provided by FSP v1.6.0 for aid in parsing the
MEM_INFO_DATA_HOB.
BUG=chrome-os-partner:61729
BRANCH=none
TEST=Build and boot KBLRVP
Change-Id: Ia2b528ba4d9f093006cc12ee317d02e7f3e83166
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18326
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
thinkpad_acpi expects a SSMS method to turn on/off the mute LED
and a MMTS method to turn on/off the microphone mute LED. With
these methods implemented the driver can correctly sync the LEDs
with the corresponding statuses.
There seems to be two different bits to mute the audio in the
Lenovo H8 EC:
* AMUT, used internally (for example to disable the audio before
entering S3).
* ALMT, controllable by the OS, which also toggles the mute LED
(if present).
Tested on a X220T and on a X201.
Change-Id: I578f95f9619a53fd35f8a8bfe5564aeb6c789212
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18329
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins)
|
|
Currently, the USB ports are still powered during S3, so turning
them off may reduce the power consumption.
Note that, when the USB Always on feature is enabled, the USB
ports are always powered, regardless of the USBP state.
This patch also disables the audio, as it might consume some
power or generate some noise.
Both the USB power and the audio are reenabled by coreboot during
the poweron.
Change-Id: If0431b1315fffef2e372e7023f830a66bb7fddae
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18464
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
On the models that support it (like the X220) the LED pulses, on
the others (like the X201) the LED powers off.
Change-Id: I2ac7dbc30609179e4ca5fc0a7b06763431fe3344
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18325
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
thinkpad_acpi expects a MHKG method which returns the current
state of the tablet mode switch shifted left by 3. If such
method is not found, subsequent laptop/tablet mode events are
ignored.
Tested on a X220T.
Change-Id: Ic9ffea2ffe507b3692d1dd7411c52b813ec32146
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18328
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
This timeout is probably needed on all devices with Lenovo H8 embedded
controllers so set the default there.
Change-Id: I830ab1894f7c0f10f55c82e398becf44d810852d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18274
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
The cr50 part on reef is connected to the SoC's UART lines. However,
when the tx signal is low it causes an interrupt to fire on cr50.
Therefore, keep the tx signal high in suspend state so that it doesn't
cause an interrupt storm on cr50 which prevents cr50 from sleeping.
BUG=chrome-os-partner:63283
BRANCH=reef
TEST=s0ix no longer causes interrupt storm on cr50. Power consumption
normal.
Change-Id: Idaeb8e4427c1cec651122de76a43daa15dc54d0f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18491
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Apply tuning for the PCH I2C buses on Eve based on rise/fall time
measurements that were done with a scope.
BUG=chrome-os-partner:59686
BRANCH=none
TEST=Manual testing on Eve P1 to verify that all devices on I2C
buses are still functional. Post-tuning measurement will be done
once a new firmware is released.
Change-Id: I3d70ff455a20ecda374d7e7fa6cd3ab15e7f2621
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18487
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
